EN 71-5:1993/A1:2006
(Amendment)Safety of toys - Part 5: Chemical toys (sets) other than experimental sets
Safety of toys - Part 5: Chemical toys (sets) other than experimental sets
Migrated from Progress Sheet (TC Comment) (2000-07-10): TC forecasts modified (TC resolution 48/2000, 2000-05-05)
Sicherheit von Spielzeug - Teil 5: Chemisches Spielzeug (Sets) ausgenommen Experimentierkästen
Sécurité des jouets - Partie 5: Jouets chimiques (coffrets) autres que les coffrets d'expériences chimiques
Varnost igrač - 5. del: Kemijske igrače (kompleti), razen kompletov za kemijske poskuse – Dopolnilo A1
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-marec-2006
9DUQRVWLJUDþGHO .HPLMVNHLJUDþH NRPSOHWL UD]HQNRPSOHWRY]DNHPLMVNH
SRVNXVH±'RSROQLOR$
Safety of toys - Part 5: Chemical toys (sets) other than experimental sets - Amendment
A1
Sicherheit von Spielzeug - Teil 5: Chemisches Spielzeug (Sets) ausgenommen
Experimentierkästen
Sécurité des jouets - Partie 5: Jouets chimiques (coffrets) autres que les coffrets
d'expériences chimiques
Ta slovenski standard je istoveten z: EN 71-5:1993/A1:2006
ICS:
97.200.50 ,JUDþH Toys
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
EN 71-5:1993/A1
NORME EUROPÉENNE
EUROPÄISCHE NORM
January 2006
ICS 97.200.50
English Version
Safety of toys - Part 5: Chemical toys (sets) other than
experimental sets
Sécurité des jouets - Partie 5: Jeux chimiques (coffrets) Sicherheit von Spielzeug - Teil 5: Chemisches Spielzeug
autres que les coffres d'expériences chimiques (Sets) ausgenommen Experimentierkästen
This amendment A1 modifies the European Standard EN 71-5:1993; it was approved by CEN on 7 December 2005.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this
amendment into the relevant national standard without any alteration. Up-to-date lists and bibliographical references concerning such
national standards may be obtained on application to the Central Secretariat or to any CEN member.
This amendment exists in three official versions (English, French, German). A version in any other language made by translation under the
responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania,
Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2006 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 71-5:1993/A1:2006: E
worldwide for CEN national Members.
Contents Page
Foreword .3
12 Test methods.6
12.1 General .6
12.2 Determination of elements in ceramic and vitreous enamelling materials .6
12.3 Determination of plasticizers in oven hardening polyvinyl chloride (PVC) modelling clay
sets.11
12.4 Determination of the emission of benzene, toluene and xylenes from oven hardening
plasticised PVC modelling sets and plastic moulding sets.23
12.5 Determination of styrene content in polystyrene granules .27
12.6 Identification and determination of substances in photographic processing sets .29
12.7 Determination of organic solvents .50
12.8 Combined approach for the determination of plasticizers in solvent-based adhesives and
in solvent-based paints and lacquers, film forming agents in paints and lacquers and
modifiers in solvent-based paints and lacquers .70
Annex A (normative) Environmental, health and safety precautions.81
Annex B (informative) Solvent content in different matrices and permitted maximum
concentration .82
Annex C (informative) Preliminary test method for the determination of elements in ceramic and
vitreous enamelling materials.83
Annex D (informative) Validation of test methods .84
Annex ZA (informative) Clauses of this European Standard addressing essential requirements or
other provisions of EU Directives.85
Bibliography.86
Foreword
This European Standard (EN 71-5:1993/A1:2006) has been prepared by Technical Committee CEN/TC 52
“Safety of toys”, the secretariat of which is held by DS.
This Amendment to the European Standard EN 71-5:1993 shall be given the status of a national standard,
either by publication of an identical text or by endorsement, at the latest by July 2006, and conflicting national
standards shall be withdrawn at the latest by July 2006.
This European Standard has been prepared under a mandate given to CEN by the European Commission
and the European Free Trade Association, and supports essential requirements of EU Directive(s).
For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this European
Standard.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden,
Switzerland and United Kingdom.
Add under "Introduction",
st
following the 1 paragraph:
Part 6: Graphical symbol for age warning labelling
Part 7: Finger paints — Requirements and test methods
Part 8: Swings, slides and similar activity toys for indoor and outdoor family domestic use
Part 9: Organic chemical compounds — Requirements
Part 10: Organic chemical compounds — Sample preparation and extraction
Part 11: Organic chemical compounds — Methods of analysis
th
following the 6 paragraph:
Under a mandate given to CEN by the European Commission, test methods were developed to determine the
migration and emission of the following substances or compounds, respectively:
• elements in ceramic and vitreous enamelling materials;
• plasticizers in oven hardening poly (vinyl chloride) (PVC) modelling clay sets;
• toluene, xylene and benzene in oven hardening plasticized PVC modelling clay sets and plastic moulding
sets;
• styrene in plastic moulding sets;
• substances in photographic processing sets;
• organic solvents in adhesives, lacquers, paints etc. and
• modifiers, film builders and plasticizers in paints and lacquers.
Five lead laboratories worked out the relevant test methods. In a second step the developed test procedures
were validated by the lead and peer review laboratories using specially manufactured or specially selected
samples (see Annex D). All test methods have been supervised by CEN/TC 52/WG 5 which also developed
EN 71-4.
th th
The 7 to 12 paragraph in the "Introduction" shall be deleted.
st
Replace the 1 sentence under Clause 1 "Scope" by
This part of EN 71 specifies requirements and test methods for the substances and materials used in chemical
toys (sets) other than experimental sets.
Amend the standard text in Clause 2 to read
The following referenced documents are indispensable for the application of this European Standard. For
dated references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
Add under Clause 2 "Normative references"
EN 14517:2004, Liquid petroleum products — Determination of hydrocarbon types and oxygenates in petrol
— Multidimensional gas chromatography method
EN ISO 3696:1995, Water for analytical laboratory use — Specification and test methods (ISO 3696:1987)
Delete the following references
ISO 3696:1987, Water for analytical laboratory use; specifications and test methods
Add the following clause:
12 Test methods
12.1 General
All chemicals used for analysis shall be of analytical grade (pro analysis) or, if unavailable, the best technical
grade. Water shall be of grade 3 according to EN ISO 3696 or of a comparable quality, and demonstrably free
from analytes of interest.
The precision of volumetric glassware should be grade A.
12.2 Determination of elements in ceramic and vitreous enamelling materials
12.2.1 Principle
The ceramic or enamel sample is submitted to a melting digestion using dilithium tetraborate. After the
dissociation the fused product is extracted by means of diluted hydrochloric acid. The individual metals are
determined by atomic emission spectrophotometry.
12.2.2 Standards and reagents
12.2.2.1 Standards
NOTE These elemental standard solutions are commercially available.
Table 16 — Standards
Chemical Concentration
mg/l
Copper 1 000
Iron 1 000
Praseodymium 1 000
Cobalt 1 000
Zirconium 1 000
Vanadium 1 000
Tin 1 000
12.2.2.2 Reagents
Table 17 — Reagents
Chemical Concentration
Di-lithium tetraborate (Li B O)
2 4 7
Hydrochloric acid
ρ(HCl) = 1,12 g/ml
12.2.3 Apparatus
NOTE As there is no standardized equipment on the market only general detailed user's instructions could be
provided.
12.2.3.1 Platinum crucible
12.2.3.2 Muffle furnace, or relevant equipment, temperature range: up to (1 000 ± 50) ºC
12.2.3.3 Analytical balance, precision 0,1 mg
12.2.3.4 Glassware (beaker, funnel, volumetric flask and pipettes)
Before use all glass equipment shall be cleaned using 10 % hydrochloric acid (per volume).
12.2.3.5 Atomic emission spectrometer
12.2.4 Preparation of standard solutions
12.2.4.1 Multi-element standard solution I
c (Cu, Fe, Pr, Co, Zr, V, Sn) = 10 mg/l
Pipette (1,0 ± 0,01) ml of each of the 1 000 mg/l standards (12.2.2.1) into a 100-ml volumetric flask. Add 10 ml
of hydrochloric acid (12.2.2.2), mix and make up to the mark with water.
NOTE The multi-element standard solution I may be stored for a month in a refrigerator at (4 ± 2) ºC.
12.2.4.2 Multi-element standard solution II
c (Cu, Fe, Pr, Co, Zr, V, Sn) = 5,0 mg/l
Pipette (50 ± 0,05) ml of the multi-element standard solution I into a 100-ml volumetric flask. Add 10 ml of
hydrochloric acid, mix and make up to the mark with water.
This solution shall be freshly prepared.
12.2.4.3 Multi-element standard solution III
c (Cu, Fe, Pr, Co, Zr, V, Sn) = 1,0 mg/l
Pipette (10 ± 0,02) ml of the multi-element standard solution I into a 100-ml volumetric flask. Add 10 ml of
hydrochloric acid, mix and make up to the mark with water.
This solution shall be freshly prepared.
12.2.5 Blank solution
Add 10 ml hydrochloric acid to 90 ml water in a polyethene- or polytetrafluorethene (PTFE)-flask.
12.2.6 Sampling
Obtain three test portions from each colour of the material and treat them separately.
NOTE Homogenisation of the test portions is not necessary because the materials have been melted and are very
finely ground.
12.2.7 Sample preparation
Weigh (0,1 ± 0,05) g to the nearest 0,001 g of each test portion in a platinum crucible. Add 1 g of dilithium
tetraborate to the crucible and mix carefully. Heat the crucible in a muffle furnace to (1 000 ± 50) ºC for
120 min.
After cooling to approximately 500 ºC remove the crucible from the muffle furnace and transfer it into a glass
of water. Add 20 ml of hydrochloric acid. Heat the solution to boiling point and let it boil until complete
dissolution of the sample occurs. Transfer the solution into a 250-ml volumetric flask and filled up to the mark.
If silicon dioxide is precipitated, remove it by filtration.
12.2.8 Procedure
Determine the elemental concentrations using the wavelengths according to Table 18. In case of spectral
interference choose an alternative appropriate wavelength.
Table 18 — Wavelengths
Element Wavelength
nm
Copper (Cu) 324,752
Iron (Fe) 259,942
Praseodymium (Pr) 422,285
Cobalt (Co) 228,616
Zirconium (Zr) 339,198
Vanadium (V) 292,399
Tin (Sn) 189,932
After the verification of the calibration function the samples are measured.
Determine the blank solutions before analysing the solutions.
Recalibrate the analytical instruments frequently. To avoid memory effects perform also checks with the blank
solution.
12.2.9 Evaluation of results
12.2.9.1 General
The mean value of three test portions shall be given.
The metal contents are calculated according to Equation (1):
(c −c )×V × f
sample blank
M = (1)
m
W ×10000
where
M is the content of the metal in the sample, in mass-%;
m
c is the concentration of the metal in the analytical solution, in mg/l;
sample
c is the concentration of the metal in the blank value solution, in mg/l;
blank
V is the volume of the sample solution, in ml;
f is the dilution factor;
W is the weighed portion of the sample, in g.
The calculated contents of elements are compared with the maximum permitted element concentrations in the
compounds given in Table C.1. If these concentrations are not exceeded, the requirements of EN 71-5 are
fulfilled.
If the concentrations are exceeded, the concentration of compounds have to be calculated according to
Equati
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.