EN 60317-0-7:2017
(Main)Specifications for particular types of winding wires - Part 0-7: General requirements - Fully insulated (FIW) zero-defect enamelled round copper wire
Specifications for particular types of winding wires - Part 0-7: General requirements - Fully insulated (FIW) zero-defect enamelled round copper wire
IEC 60317-0-7:2017 establishes general requirements for fully insulated (FIW) zero-defect enamelled round copper wires. The nominal conductor diameter range is given in the relevant technical specification. This second edition cancels and replaces the first edition published in 2012. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: - reduction in the number of grades of FIW from 3 through 9 to 4, 6 and 8 only; - reduction of the wire diameter range from (0,040 to 1,000) mm to (0,090 to 0,900) mm for several requirements; - revision of Clause 5 to delete the Table 2 resistance requirements; - revision of Clause 13 to clarify that breakdown is determined when a calculated minimum test voltage is reached, which can be less than 10 000 V; - expansion of Annex A to include requirements for FIW 3, 5, 7 and 9 and for all grades, wire diameters below 0,090 mm and above 0,900 mm. Keywords: insulated wires used for windings
Technische Lieferbedingungen für bestimmte Typen von Wickeldrähten - Teil 0-7: Allgemeine Anforderungen - Isolationsfehlerfreie Runddrähte (FIW) aus Kupfer, lackisoliert
Spécifications pour types particuliers de fils de bobinage - Partie 0-7: Exigences générales - Fil de section circulaire, isolé en continu (FIW), en cuivre émaillé, sans défaut d'isolation électrique
IEC 60317-0-7:2017 établit les exigences générales relatives aux fils de section circulaire, isolés en continu, en cuivre émaillé, sans défaut d'isolation électrique. La gamme des diamètres nominaux des conducteurs est donnée dans la spécification technique appropriée. Cette deuxième édition annule et remplace la première édition parue en 2012. Cette édition constitue une révision technique. La présente édition inclut les modifications techniques majeures suivantes par rapport à l’édition précédente: - réduction du nombre de grades FIW compris entre 3 et 9, qui se limitent à 4, 6 et 8 seulement; - réduction de la gamme de diamètres des conducteurs, qui passe de (0,040 à 1,000) mm à (0,090 à 0,900) mm pour plusieurs exigences; - révision de l’Article 5 pour supprimer les exigences de résistance du Tableau 2; - révision de l’Article 13 pour préciser que le claquage est déterminé lorsqu’une tension minimale d’essai calculée est atteinte, qui peut être inférieure à 10 000 V; - extension de l’Annexe A afin d’intégrer des exigences concernant les grades FIW 3, 5, 7 et 9 ainsi que tous les grades dont les diamètres de conducteurs sont inférieurs à 0,090 mm et supérieurs à 0,900 mm. Mots clés: fils isolés utilisés dans les enroulements
Specifikacije za posebne vrste navijalnih žic - 0-7. del: Splošne zahteve - Popolnoma izolirana in brezhibno lakirana okrogla bakrena žica (IEC 60317-0-7:2017)
Ta del IEC 60317 določa splošne zahteve za popolnoma izolirane in brezhibno lakirane okrogle bakrene žice.
Razpon nazivnega premera prevodnika je naveden v ustrezni tehnični specifikaciji.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-januar-2018
1DGRPHãþD
SIST EN 60317-0-7:2012
Specifikacije za posebne vrste navijalnih žic - 0-7. del: Splošne zahteve -
Popolnoma izolirana in brezhibno lakirana okrogla bakrena žica (IEC 60317-0-
7:2017)
Specifications for particular types of winding wires - Part 0-7: General requirements -
Fully insulated (FIW) zero-defect enamelled round copper wire (IEC 60317-0-7:2017)
Ta slovenski standard je istoveten z: EN 60317-0-7:2017
ICS:
29.060.10 Žice Wires
77.150.30 Bakreni izdelki Copper products
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD EN 60317-0-7
NORME EUROPÉENNE
EUROPÄISCHE NORM
November 2017
ICS 29.060.10 Supersedes EN 60317-0-7:2012
English Version
Specifications for particular types of winding wires -
Part 0-7: General requirements - Fully insulated (FIW) zero-
defect enamelled round copper wire
(IEC 60317-0-7:2017)
Spécifications pour types particuliers de fils de bobinage - Technische Lieferbedingungen für bestimmte Typen von
Partie 0-7: Exigences générales - Fil de section circulaire, Wickeldrähten - Teil 0-7: Allgemeine Anforderungen -
isolé en continu (FIW), en cuivre émaillé, sans défaut Isolationsfehlerfreie Runddrähte (FIW) aus Kupfer,
d'isolation électrique lackisoliert
(IEC 60317-0-7:2017) (IEC 60317-0-7:2017)
This European Standard was approved by CENELEC on 2017-09-20. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden,
Switzerland, Turkey and the United Kingdom.
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2017 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN 60317-0-7:2017 E
European foreword
The text of document 55/1619/FDIS, future edition 2 of IEC 60317-0-7, prepared by
IEC/TC 55 "Winding wires" was submitted to the IEC-CENELEC parallel vote and approved by
CENELEC as EN 60317-0-7:2017.
The following dates are fixed:
(dop) 2018-06-20
• latest date by which the document has to be
implemented at national level by
publication of an identical national
standard or by endorsement
• latest date by which the national (dow) 2020-09-20
standards conflicting with the
document have to be withdrawn
This document supersedes EN 60317-0-7:2012.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
Endorsement notice
The text of the International Standard IEC 60317-0-7:2017 was approved by CENELEC as a
European Standard without any modification.
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1 Where an International Publication has been modified by common modifications, indicated by (mod), the relevant
EN/HD applies.
NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available here:
www.cenelec.eu.
Publication Year Title EN/HD Year
IEC 60172 - Test procedure for the determination EN 60172 -
of the temperature index of enamelled
and tape wrapped winding wires
IEC 60317-0-1 2013 Specifications for particular types EN 60317-0-1 2014
of winding wires -
Part 0-1: General requirements -
Enamelled round copper wire
IEC 60851 Series Winding wires - Test methods EN 60851 Series
IEC 60851-5 2008 Winding wires - Test methods - EN 60851-5 2008
Part 5: Electrical properties
+A1 2011 +A1 2011
ISO 3 - Preferred numbers - Series of preferred - -
numbers
IEC 60317-0-7 ®
Edition 2.0 2017-08
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Specifications for particular types of winding wires –
Part 0-7: General requirements – Fully insulated (FIW) zero-defect enamelled round
copper wire
Spécifications pour types particuliers de fils de bobinage –
Partie 0-7: Exigences générales – Fil de section circulaire, isolé en continu (FIW),
en cuivre émaillé, sans défaut d'isolation électrique
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 29.060.10 ISBN 978-2-8322-4722-8
– 2 – IEC 60317-0-7:2017 © IEC 2017
CONTENTS
FOREWORD . 4
INTRODUCTION . 6
1 Scope . 7
2 Normative references . 7
3 Terms, definitions, general notes and appearance . 7
3.1 Terms and definitions . 7
3.2 General notes . 9
3.2.1 Methods of test . 9
3.2.2 Winding wire . 9
3.3 Appearance . 9
4 Dimensions. 9
4.1 Conductor diameter . 9
4.2 Out of roundness of conductor (for nominal diameters over 0,090 mm up to
0,900 mm) . 10
4.3 Minimum overall diameter . 10
4.4 Maximum overall diameter . 10
5 Electrical resistance . 11
6 Elongation . 11
7 Springiness . 11
8 Flexibility and adherence . 12
8.1 Mandrel winding test (for nominal conductor diameters over 0,090 mm up to
0,900 mm) . 12
8.2 Jerk test (for nominal diameters up to 0,900 mm) . 13
9 Heat shock . 13
10 Cut through . 14
11 Resistance to abrasion . 14
12 Resistance to solvents . 14
13 Breakdown voltage . 14
14 Continuity of insulation (nominal conductor diameters over 0,090 mm up to
0,900 mm) . 15
14.1 Off-line high voltage continuity . 15
14.2 In-line high voltage continuity . 15
15 Temperature index . 15
16 Resistance to refrigerants . 15
17 Solderability . 15
18 Heat or solvent bonding . 15
19 Dielectric dissipation factor . 16
20 Resistance to transformer oil . 16
21 Loss of mass . 16
23 Pin-hole test . 16
30 Packaging . 16
Annex A (normative) Supplemental requirements for FIW . 17
A.1 Dimensions . 17
A.2 Electrical resistance . 18
IEC 60317-0-7:2017 © IEC 2017 – 3 –
A.3 Elongation . 19
A.4 Springiness . 20
A.5 Mandrel winding test . 21
A.6 Heat shock . 22
A.7 Breakdown voltage . 24
Table 1 – Dimensions of enamelled wires (R 20). 10
Table 2 – Elongation at break . 11
Table 3 – Springiness . 12
Table 4 – Mandrel diameters for mandrel winding test . 13
Table 5 – Heat shock . 14
Table 6 – Breakdown voltage . 15
Table A.1 – Dimensions of enamelled wires for grades FIW 3, 5, 7 and 9 . 17
Table A.2 – Dimensions of enamelled wires up to and including 0,090 mm and over
0,900 mm (R 20) for grades FIW 4, 6 and 8 . 18
Table A.3 – Electrical resistance . 19
Table A.4 – Elongation at break . 19
Table A.5 – Springiness for grades FIW 3, 5, 7 and 9 . 20
Table A.6 – Springiness for grades FIW 4, 6 and 8 . 21
Table A.7 – Mandrel diameters for mandrel winding test for grade FIW 3, 5, 7 and 9 . 21
Table A.8 – Mandrel diameters for mandrel winding test for grade FIW 4, 6 and 8,
nominal conductor diameters up to and including 0,090 m
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.