EN 62752:2016
(Main)In-cable control and protection device for mode 2 charging of electric road vehicles (IC-CPD)
In-cable control and protection device for mode 2 charging of electric road vehicles (IC-CPD)
IEC 62752:2016 applies to in-cable control and protection devices (IC-CPDs) for mode 2 charging of electric road vehicles, hereafter referred to as IC-CPD including control and safety functions. This standard applies to portable devices performing simultaneously the functions of detection of the residual current, of comparison of the value of this current with the residual operating value and of opening of the protected circuit when the residual current exceeds this value.
Ladeleitungsintegrierte Steuer- und Schutzeinrichtung für die Ladebetriebsart 2 von Elektro-Straßenfahrzeugen (IC-CPD)
Appareil de contrôle et de protection intégré au câble pour la charge en mode 2 des véhicules électriques (IC-CPD)
L'IEC 62752:2016 s'applique aux appareils de contrôle et de protection intégrés au câble (IC-CPD) pour la charge en mode 2 des véhicules électriques, qui seront désignés IC-CPD par la suite, y compris les fonctions de commande et de sécurité. La présente Norme s'applique aux appareils mobiles qui remplissent à la fois les fonctions de détection du courant résiduel, de comparaison de la valeur de ce courant à une valeur d'exploitation différentielle et d'ouverture du circuit protégé quand le courant différentiel résiduel dépasse cette valeur.
Intergirana zaščita kabla in zaščitna naprava tipa 2 za napajanje električnih cestnih vozil (IC-CPD) (IEC 62752:2016)
Ta mednarodni standard se uporablja za integrirane zaščite kablov in zaščitne naprave (IC-CPD) tipa 2 za napajanje električnih cestnih vozil, v nadaljevanju »IC-CPD«, vključno z nadzornimi in zaščitnimi funkcijami.
Ta standard se uporablja za prenosne naprave, ki hkrati izvajajo funkcije zaznavanja preostalega (residualnega) toka, primerjanja vrednosti tega toka s preostalo obratovalno vrednostjo in odprtja zaščitenega tokokroga, kadar preostali tok preseže to vrednost.
IC-CPD v skladu s tem standardom:
• vključuje krmilni upravljavec v skladu s standardom IEC TS 62763;
• preverja pogoje napajanja in preprečuje napajanje v primeru napake pod določenimi pogoji;
• lahko vključuje zaščitni vodnik.
Ti IC-CPD-ji so namenjeni za uporabo v sistemih TN in TT.
Uporaba IC-CPD-jev in sistemov IT je lahko omejena.
Obravnavani so preostali (residualni) tokovi s frekvencami, različnimi od nazivne frekvence, enosmerni preostali (residualni) tokovi in specifične okoljske razmere.
Ta standard se uporablja za IC-CPD-je z varnostnimi in nadzornimi funkcijami, kot je zahtevano v standardu IEC 61851-1 za napajanje električnih vozil tipa 2.
Ta standard se uporablja za IC-CPD-je za enofazne krogotoke, ki ne presegajo 250 V, ali večfazne
krogotoke, ki ne presegajo 480 V, pri čemer je njihov največji nazivni tok 32 A.
OPOMBA 1: Na Danskem se uporablja še naslednja dodatna zahteva: za IC-CPD-je z vtičem za gospodinjsko
in podobno uporabo uporabite največji napajalni tok 8 A, če lahko polnilni cikel traja dlje kot 2 uri.
OPOMBA 2: Na Finskem se uporablja tudi naslednja dodatna zahteva: za IC-CPD-je z vtičem za gospodinjsko in podobno uporabo uporabite največji napajalni tok 8 A za dolgotrajno napajanje.
Ta standard se uporablja za IC-CPD-je, ki se uporabljajo samo v izmeničnem električnem toku, s priporočenimi vrednostmi frekvence med 50 in 60 Hz ali 50/60 Hz. Glede na ta standard IC-CPD-ji niso namenjeni oskrbi priklopljene mreže z električno energijo.
Ta standard se uporablja za IC-CPD-je, katerih preostali (residualni) tok ne presega vrednosti 30 mA in ki so namenjeni za dodatno zaščito krogotoka IC-CPD-ja v smeri toka v primerih, ko ni možno zagotoviti, da je inštalacija opremljena z napravo na preostali (residualni) tok z vrednostjo IΔn ≤ 30 mA.
IC-CPD vključuje:
• vtič za povezavo z izhodno vtičnico fiksne inštalacije;
• enega ali več podsklopov, ki vsebujejo kontrolne in zaščitne funkcije;
• kabel med vtičem in podsklopi (izbirno);
• kabel med podsklopi in konektorjem vozila (izbirno);
• priključek vozila za povezavo z električnim vozilom.
Za vtiče za gospodinjsko in podobno uporabo se uporabljajo zahteve nacionalnih standardov in specifične zahteve, ki jih je določil nacionalni komite države prodaje proizvoda. Če nacionalne zahteve ne obstajajo, se lahko uporabi IEC 60884-1.
Za industrijske vtiče se uporablja IEC 60309-2. Za specifične aplikacije in območja se lahko uporabijo nezamenljivi industrijski vtiči. V tem primeru se uporablja standard EN 60309-1.
OPOMBA 3: Na Danskem: zahteve tega standarda ne nadomestijo ali spremenijo katerega koli dela danskih nacionalnih zahtev za vtiče za gospodinjsko in podobno uporabo v skladu s standardom DS 60884-2-D1.
Vtiči, priključki in kabli, ki so del IC-CPD-ja v skladu s tem standardom niso preskušeni. Ti deli so preskušeni ločeno v skladu z ustreznim standardom za proizvode.
OPOMBA 4: V naslednjih državah zahteve za komplete kablov EV (tipa 2) zajemajo NMX-J 677-ANCE- 2013/ CSA C22.2 št. 280-13/ UL 2594: Standard za napajalno opremo električnega vozila: US, CA, MX.
Za preklopne kontakte IC-CPD-ja ni treba zagotoviti izolacije, saj je ta zagotovljena z izklopom vtiča.
IC-CPD lahko ima v fazi/fazah in/ali nevtralni tokovni poti nezamenljivo vgrajeno varovalko.
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Ladeleitungsintegrierte Steuer- und Schutzeinrichtung für die Ladebetriebsart 2 von Elektro-Straßenfahrzeugen (IC-CPD) (IEC 62752:2016)Appareil de contrôle et de protection intégré au câble pour la charge en mode 2 des véhicules électriques (IC-CPD) (IEC 62752:2016)In-Cable Control and Protection Device for mode 2 charging of electric road vehicles (IC-CPD) (IEC 62752:2016)43.120Electric road vehicles29.120.50Fuses and other overcurrent protection devicesICS:Ta slovenski standard je istoveten z:EN 62752:2016SIST EN 62752:2016en,fr,de01-december-2016SIST EN 62752:2016SLOVENSKI
STANDARDSIST EN 61851-1:20111DGRPHãþD
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 62752
August 2016 ICS 29.120.50
Supersedes
EN 61851-1:2011 (partially)
English Version
In-cable control and protection device for mode 2 charging of electric road vehicles (IC-CPD) (IEC 62752:2016)
Appareil de contrôle et de protection intégré au câble pour la charge en mode 2 des véhicules électriques (IC-CPD) (IEC 62752:2016)
Ladeleitungsintegrierte Steuer- und Schutzeinrichtung für die Ladebetriebsart 2 von Elektro-Straßenfahrzeugen (IC-CPD) (IEC 62752:2016) This European Standard was approved by CENELEC on 2016-04-08. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique Europäisches Komitee für Elektrotechnische Normung CEN-CENELEC Management Centre: Avenue Marnix 17,
B-1000 Brussels © 2016 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN 62752:2016 E SIST EN 62752:2016
The following dates are fixed: • latest date by which the document has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2017-02-19 • latest date by which the national standards conflicting with the document have to be withdrawn (dow) 2017-12-31
This European Standard partially supersedes EN 61851-1:2011 for what concerns the product IC-CPD as a cable assembly for mode 2 EV charging. The DOW will be 2017-12-31.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such patent rights.
This document has been prepared under a mandate given to CENELEC by the European Commission and the European Free Trade Association, and supports essential requirements of EU Directive(s).
For the relationship with EU Directives see informative Annexes ZZA and ZZB, which are integral parts of this document.
Endorsement notice The text of the International Standard IEC 62752:2016 was approved by CENELEC as a European Standard without any modification. In the official version, for Bibliography, the following notes have to be added for the standards indicated:
IEC 60269-1:2006 NOTE Harmonized as EN 60269-1:2007 (not modified). IEC 60364 Series NOTE Harmonized as HD 384/HD 60364 Series. IEC 60364-7-722 NOTE Harmonized as HD 60364-7-722. IEC 60999-1:1999 NOTE Harmonized as EN 60999-1:2000 (not modified). IEC 60947-1:2007 NOTE Harmonized as EN 60947-1:2007 (not modified). IEC 61008-1:2010 NOTE Harmonized as EN 61008-1:2012 (modified). IEC 62423:2009 NOTE Harmonized as EN 62423:2009 (modified). SIST EN 62752:2016
Normative references to international publications with their corresponding European publications
The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
NOTE 1 When an International Publication has been modified by common modifications, indicated by (mod), the relevant EN/HD applies.
NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available here: www.cenelec.eu
Publication Year Title EN/HD Year
IEC 60065 -
Audio, video and similar electronic apparatus - Safety requirements EN 60065 -
IEC 60068-2-1 -
Environmental testing -
Part 2-1: Tests - Test A: Cold EN 60068-2-1 -
IEC 60068-2-5 -
Environmental testing -
Part 2-5: Tests - Test Sa: Simulated solar radiation at ground level and guidance for solar radiation testing EN 60068-2-5 -
IEC 60068-2-11 -
Basic environmental testing procedures - Part 2-11: Tests - Test Ka: Salt mist EN 60068-2-11 -
IEC 60068-2-27 -
Environmental testing -
Part 2-27: Tests - Test Ea and guidance: Shock EN 60068-2-27 -
IEC 60068-2-30 -
Environmental testing -
Part 2-30: Tests - Test Db: Damp heat, cyclic (12 h + 12 h cycle) EN 60068-2-30 -
IEC 60068-2-31 -
Environmental testing -
Part 2-31: Tests - Test Ec: Rough handling shocks, primarily for equipment-type specimens EN 60068-2-31 -
IEC 60068-2-64 -
Environmental testing -
Part 2-64: Tests - Test Fh: Vibration, broadband random and guidance EN 60068-2-64 -
IEC 60068-3-4 -
Environmental testing -
Part 3-4: Supporting documentation and guidance - Damp heat tests EN 60068-3-4 -
IEC 60112 -
Method for the determination of the proof and the comparative tracking indices of solid insulating materials EN 60112 -
IEC 60227 Series
Polyvinyl chloride insulated cables of rated voltages up to and including 450/750 V - - IEC 60245 Series
Rubber insulated cables - Rated voltages up to and including 450/750 V - -
IEC 60309 Series
Plugs, socket-outlets and couplers for industrial purposes
EN 60309 Series
IEC 60309-1 1999
Plugs, socket-outlets and couplers for industrial purposes -
Part 1: General requirements EN 60309-1 +A11 1999
2004 +A1 (mod) 2005
+A1 2007
+A2 2012
+A2 2012
IEC 60309-2 -
Plugs, socket-outlets and couplers for industrial purposes -
Part 2: Dimensional interchangeability requirements for pin and contact-tube accessories EN 60309-2 -
IEC 60364-4-44 (mod) 2007
Low-voltage electrical installations -
Part 4-44: Protection for safety - Protection against voltage disturbances and electromagnetic disturbances HD 60364-4-442 2012
IEC 60384-14 Series
Fixed capacitors for use in electronic equipment -
Part 14: Sectional specification - Fixed capacitors for electromagnetic interference suppression and connection to the supply mains EN 60384-14 Series
IEC 60417-DB -
Graphical symbols for use on equipment - -
IEC 60529 1989
Degrees of protection provided by enclosures (IP Code) EN 60529 + corr. May 1991
1993 IEC 60664-1 2007
Insulation coordination for equipment within low-voltage systems -
Part 1: Principles, requirements and tests EN 60664-1 2007
IEC 60664-3 -
Insulation coordination for equipment within low-voltage systems -
Part 3: Use of coating, potting or moulding for protection against pollution EN 60664-3 -
IEC 60695-2-10 -
Fire hazard testing -
Part 2-10: Glowing/hot-wire based test methods - Glow-wire apparatus and common test procedure EN 60695-2-10 -
IEC 60695-2-11 -
Fire hazard testing -
Part 2-11: Glowing/hot-wire based test methods - Glow-wire flammability test method for end-products (GWEPT) EN 60695-2-11 -
IEC 60884-1 2002
Plugs and socket-outlets for household and similar purposes -
Part 1: General requirements - -
+A1 2006
- -
+A2 2013
- -
IEC 61249-2 Series
Materials for printed boards and other interconnecting structures EN 61249-2 Series
IEC 61540 -
Electrical accessories - Portable residual current devices without integral overcurrent protection for household and similar use (PRCDs) HD 639 S1 -
IEC 61543 1995
Residual current-operated protective devices (RCDs) for household and similar use - Electromagnetic compatibility EN 61543 + corr. December +A11 +A12 1995
1997 2003 2005 +A1 2004
- -
+A2 2005
+A2 2006
IEC 61851-1 2010
Electric vehicle conductive charging system -
Part 1: General requirements EN 61851-1 2011
IEC 62196-1 -
Plugs, socket-outlets, vehicle connectors and vehicle inlets - Conductive charging of electric vehicles -
Part 1: General requirements EN 62196-1 -
IEC 62196-2 -
Plugs, socket-outlets, vehicle connectors and vehicle inlets - Conductive charging of electric vehicles -
Part 2: Dimensional compatibility and interchangeability requirements for a.c. pin and contact-tube accessories EN 62196-2 -
IEC/TS 62763 2013
Pilot function through a control pilot circuit using PWM modulation and a control pilot wire - -
CISPR 14 Series
Electromagnetic compatibility - Requirements for household appliances, electric tools and similar apparatus EN 55014 Series
ISO 178 -
Plastics - Determination of flexural properties EN ISO 178 -
ISO 179 Series
Plastics - Determination of Charpy impact properties EN ISO 179 Series
ISO 179-1 -
Plastics - Determination of Charpy impact properties -
Part 1: Non-instrumented impact test EN ISO 179-1 -
ISO 2409 -
Paints and varnishes - Cross-cut test EN ISO 2409 -
ISO 4628-3 -
Paints and varnishes - Evaluation of degradation of coatings - Designation of quantity and size of defects, and of intensity of uniform changes in appearance - Part 3: Assessment of degree of rusting EN ISO 4628-3 -
ISO 4892-2 2013
Plastics - Methods of exposure to laboratory light sources -
Part 2: Xenon-arc lamps EN ISO 4892-2 2013
ISO 16750-5 2010
Road vehicles - Environmental conditions and testing for electrical and electronic equipment -
Part 5: Chemical loads - -
ISO 17409 2015
Electrically propelled road vehicles - Connection to an external electric power supply - Safety requirements - -
(normative)
Special national conditions
Special national condition: National characteristic or practice that cannot be changed even over a long period, e.g. climatic conditions, electrical earthing conditions.
NOTE If it affects harmonization, it forms part of the European Standard or Harmonization Document.
For the countries in which the relevant special national conditions apply these provisions are normative, for other countries they are informative.
Country Clause Special national condition Denmark 1 IC-CPD: For IC-CPDs supplied with a plug for household and similar use, repeated continuous loads of long duration, shall be limited to 6 A. Finland 1 IC-CPD: The following additional requirement applies: for IC-CPDs supplied with a plug for household and similar use the maximum charging current is 8 A for long lasting charging. Norway 4.3.4 IC-CPD: In Norway, pluggable types where connector is part of the ICCB shall not be used. Switzerland 5.3.2 IC-CPD: In Switzerland, simplified control pilot circuit is not allowed. Switzerland 5.3.2 IC-CPD: In Switzerland, the use of EN 60309-2 accessories is recommended for mode 2 connections for more than 8 A (2 kVA). France 8.1 IC-CPD: In France, the use of solid brass pins is required. France 8.3.1 IC-CPD: In France, For a rated current above 8 A, rewirable connections of the household plug are not allowed. Connection between the household plugs and cable shall use terminations (see definition 3.2.3). Switzerland 8.3.1 IC-CPD: In Switzerland, the use of EN 60309-2 accessories is recommended for mode 2 connections for more than 8 A (2 kVA). Belgium 9.7.7.4 IC-CPD: In Belgium, an IC-CPD shall be able to function properly in both LNE and LLE configurations, provided the correct voltage is available.
A-deviations
A-deviation: National deviation due to regulations, the alteration of which is for the time being outside the competence of the CEN-CENELEC national member.
This European Standard falls under Directives 2014/35/EU and 2014/30/EU.
NOTE
(from CEN/CENELEC IR Part 2:2015, 2.16) Where standards fall under EC Directives or Regulations, it is the view of the Commission of the European Communities (OJ No C 59; 1982-03-09) that the effect of the decision of the Court of Justice in case 815/79 Cremonini/Vrankovich (European Court Reports 1980, p. 3583) is that compliance with A-deviations is no longer mandatory and that the free movement of products complying with such a standard should not be restricted within the EC except under the safeguard procedure provided for in the relevant Directive or Regulation.
A-deviations in an EFTA-country are valid instead of the relevant provisions of the European Standard in that country until they have been removed.
Country Clause A-deviation Denmark General The requirements in this standard cannot replace or change any part of the Danish National requirements for plugs for household and similar use according to DS 60884-2-D1. SIST EN 62752:2016
Relationship between this European standard and the essential requirements of Directive 2014/30/EU [2014 OJ L96] aimed to be covered
This European standard has been prepared under a Commission’s standardisation request as regards harmonised standards in support of Directive 2014/30/EU relating to electromagnetic compatibility,to provide one voluntary means of conforming to essential requirements of Directive 2014/30/EU of the European Parliament and of the Council of 26 February 2014 on the harmonisation of the laws of the Member States relating to electromagnetic compatibility [2014 OJ L96].
Once this standard is cited in the Official Journal of the European Union under that Directive, compliance with the normative clauses of this standard given in Table ZZA.1 conf
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.