EN 60252-2:2011

AC motor capacitors - Part 2: Motor start capacitors

IEC 60252-2:2010 applies to motor start capacitors intended for connection to windings of asynchronous motors supplied from a single-phase system having the frequency of the mains. Covers impregnated or unimpregnated metallized motor start capacitors having a dielectric of paper or plastic film, or a combination of both and electrolytic motor start capacitors with non-solid electrolyte, with rated voltages up to and including 660 V. The main changes with respect to the previous edition are: - definition of segmented film capacitors; - clearer definition of the purpose of d.c. conditioning in destruction test.

Wechselspannungsmotorkondensatoren - Teil 2: Motoranlaufkondensatoren

Condensateurs des moteurs à courant alternatif - Partie 2: Condensateurs de démarrage de moteurs

La CEI 60252-2:2010 s'applique aux condensateurs de démarrage destinés à être raccordés aux enroulements des moteurs asynchrones alimentés par un réseau monophasé dont la fréquence est celle du réseau. La présente norme couvre les condensateurs de démarrage métallisés imprégnés ou non, ayant un diélectrique en papier, film plastique ou une combinaison des deux, et les condensateurs électrolytiques de démarrage à électrolyte non solide, pour une tension assignée n'excédant pas 660 V. Les principales modifications par rapport à l'édition précédente sont: - définition des condensateurs à film segmenté; - définition plus claire du conditionnement en courant continu en l'essai de destruction.

Izmenični kondenzatorji za motorje - 2. del: Zaganjalni kondenzatorji (IEC 60252-2:2010)

Ta del IEC 60252 velja za zaganjalne kondenzatorje, namenjene povezavi z navitji asinhronih motorjev, napajanih iz enofaznega sistema, ki imajo frekvenco javnega omrežja.
Ta standard zajema zaganjalne kondenzatorje motorjev, ki so ali niso impregnirani in ki imajo dielektrik iz papirja ali plastičnega filma ali kombinacije obeh, ter elektrolitske zaganjalne kondenzatorje, ki nimajo trdnih elektrolitov, z ocenjeno napetostjo do in vključno 660 V.

General Information

• Status: Published
• Publication Date: 10-Feb-2011
• Withdrawal Date: 18-Jan-2014
• ICS: 31.060.30 - Paper and plastics capacitors
• ICS: 31.060.70 - Power capacitors
• Technical Committee: CLC/SR 33 - Power capacitors
• Drafting Committee: IEC/TC 33 - IEC_TC_33
• Parallel Committee: IEC/TC 33 - IEC_TC_33
• Current Stage: 6060 - Document made available - Publishing
• Start Date: 11-Feb-2011
• Completion Date: 11-Feb-2011
• Directive: 2006/95/EC - Directive 2006/95/EC of the European Parliament and of the Council of 12 December 2006 on the harmonisation of the laws of Member States relating to electrical equipment designed for use within certain voltage limits (codified version)
• Directive: 2014/35/EU - Directive 2014/35/EU of the European Parliament and of the Council of 26 February 2014 on the harmonisation of the laws of the Member States relating to the making available on the market of electrical equipment designed for use within certain voltage limits
• Directive: 2014/53/EU - Directive 2014/53/EU of The European Parliament and of the Council of 16 April 2014 on the harmonisation of the laws of the Member States relating to the making available on the market of radio equipment and repealing Directive 1999/5/EC
• Ref Project: SIST EN 60252-2:2011 - AC motor capacitors - Part 2: Motor start capacitors (IEC 60252-2:2010)

Relations

• Replaces: EN 60252-2:2003 - AC motor capacitors - Part 2: Motor start capacitors
• Effective Date: 28-Jan-2023
• Amended By: EN 60252-2:2011/A1:2013 - AC motor capacitors - Part 2: Motor start capacitors
• Effective Date: 28-Jan-2023

Standards Content (Sample)

SLOVENSKI STANDARD
01-april-2011
1DGRPHãþD
SIST EN 60252-2:2003
,]PHQLþQLNRQGHQ]DWRUML]DPRWRUMHGHO=DJDQMDOQLNRQGHQ]DWRUML,(&

AC motor capacitors - Part 2: Motor start capacitors (IEC 60252-2:2010)
Wechselspannungsmotorkondensatoren - Teil 2: Motoranlaufkondensatoren (IEC 60252-
2:2010)
Condensateurs des moteurs à courant alternatif - Partie 2: Condensateurs de démarrage
de moteurs (CEI 60252-2:2010)
Ta slovenski standard je istoveten z: EN 60252-2:2011
ICS:
31.060.70 0RþQRVWQLNRQGHQ]DWRUML Power capacitors
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN 60252-2
NORME EUROPÉENNE
February 2011
EUROPÄISCHE NORM
ICS 31.060.30; 31.060.70 Supersedes EN 60252-2:2003

English version
AC motor capacitors -
Part 2: Motor start capacitors
(IEC 60252-2:2010)
Condensateurs des moteurs à courant Wechselspannungsmotorkondensatoren -
alternatif - Teil 2: Motoranlaufkondensatoren
Partie 2: Condensateurs de démarrage de (IEC 60252-2:2010)
moteurs
(CEI 60252-2:2010)
This European Standard was approved by CENELEC on 2011-01-19. CENELEC members are bound to comply
with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard
the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the Central Secretariat or to any CENELEC member.

This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and notified
to the Central Secretariat has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus,
the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy,
Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia,
Spain, Sweden, Switzerland and the United Kingdom.

CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung

Management Centre: Avenue Marnix 17, B - 1000 Brussels

© 2011 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 60252-2:2011 E
Foreword
The text of document 33/476/FDIS, future edition 2 of IEC 60252-2, prepared by IEC TC 33, Power
capacitors, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as
EN 60252-2 on 2011-01-19.
This European Standard supersedes EN 60252-2:2003.
The main changes with respect to EN 60252-2:2003 are listed below:
– definition of segmented film capacitors;
– clearer definition of the purpose of d.c. conditioning in destruction test.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN and CENELEC shall not be held responsible for identifying any or all such patent
rights.
The following dates were fixed:
– latest date by which the EN has to be implemented
at national level by publication of an identical
(dop) 2011-10-19
national standard or by endorsement
– latest date by which the national standards conflicting
(dow) 2014-01-19
with the EN have to be withdrawn
Annex ZA has been added by CENELEC.
__________
Endorsement notice
The text of the International Standard IEC 60252-2:2010 was approved by CENELEC as a European
Standard without any modification.
__________
- 3 - EN 60252-2:2011
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications

The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.

NOTE  When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD
applies.
Publication Year Title EN/HD Year

IEC 60062 - Marking codes for resistors and capacitors EN 60062 -

IEC 60068-2 Series Environmental testing - EN 60068-2 Series
Part 2: Tests
IEC 60068-2-6 - Environmental testing - EN 60068-2-6 -
Part 2-6: Tests - Test Fc: Vibration
(sinusoidal)
IEC 60068-2-14 - Environmental testing - EN 60068-2-14 -
Part 2-14: Tests - Test N: Change of
temperature
IEC 60068-2-20 - Environmental testing - EN 60068-2-20 -
Part 2-20: Tests - Test T: Test methods for
solderability and resistance to soldering heat
of devices with leads
IEC 60068-2-21 - Environmental testing - EN 60068-2-21 -
Part 2-21: Tests - Test U: Robustness of
terminations and integral mounting devices

IEC 60068-2-78 2001 Environmental testing - EN 60068-2-78 2001
Part 2-78: Tests - Test Cab: Damp heat,
steady state
IEC 60112 - Method for the determination of the proof and EN 60112 -
the comparative tracking indices of solid
insulating materials
IEC 60309-1 1999 Plugs, socket-outlets and couplers for EN 60309-1 1999
industrial purposes -
Part 1: General requirements
IEC 60529 - Degrees of protection provided by enclosures - -
(IP Code)
IEC 60695-2-10 2000 Fire hazard testing - EN 60695-2-10 2001
Part 2-10: Glowing/hot-wire based test
methods - Glow-wire apparatus and common
test procedure
IEC 60695-2-11 2000 Fire hazard testing - EN 60695-2-11 2001
Part 2-11: Glowing/hot-wire based test
methods - Glow-wire flammability test method
for end-products
Publication Year Title EN/HD Year
ISO 4046 - Paper, board, pulp and related terms - - -
Vocabulary
IEC 60252-2 ®
Edition 2.0 2010-12
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
AC motor capacitors –
Part 2: Motor start capacitors

Condensateurs des moteurs à courant alternatif –
Partie 2: Condensateurs de démarrage de moteurs

INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
PRICE CODE
INTERNATIONALE
X
CODE PRIX
ICS 31.060.30; 31.060.70 ISBN 978-2-88912-293-6
– 2 – 60252-2 Ó IEC:2010
CONTENTS
FOREW ORD . 4
1 Sc o pe . 6
2 Normative references . 6
3 Terms and definitions . 7
4 Service conditions . 10
4.1 Normal service conditions . 10
4.2 Preferred tolerances on capacitance . 10
5 Self-healing motor start capacitors . 10
5.1 Quality requirements and tests . 10
5.1.1 Test requirements . 10
5.1.2 Nature of tests . 11
5.1.3 Type tests . 11
5.1.4 Routine tests . 13
5.1.5 Tangent of the loss-angle measurement . 13
5.1.6 Visual examination . 13
5.1.7 Voltage test between the terminals . 14
5.1.8 Voltage test between terminals and case . 14
5.1.9 Capacitance measurement . 14
5.1.10 Check of dimensions . 14
5.1.11 Mechanical tests . 15
5.1.12 Sealing test . 17
5.1.13 Endurance test . 17
5.1.14 Damp heat test . 19
5.1.15 Self-healing test . 19
5.1.16 Destruction test . 19
5.1.17 Resistance to heat, fire and tracking . 22
5.2 Overloads . 23
5.2.1 Maximum permissible voltage . 23
5.2.2 Maximum permissible current . 23
5.2.3 Maximum permissible reactive output . 23
5.3 Safety requirements . 23
5.3.1 Creepage distances and clearances . 23
5.3.2 Terminals and connecting cables . 24
5.3.3 Earth connections . 24
5.3.4 Discharge devices . 25
5.3.5 Pollution . 25
5.4 Marking . 25
6 Electrolytic motor start capacitors . 26
6.1 Quality requirements and tests . 26
6.1.1 Test requirements . 26
6.1.2 Nature of tests . 26
6.1.3 Type tests . 27
6.1.4 Routine tests . 29
6.1.5 Visual examination . 29
6.1.6 Voltage test between the terminals . 29
6.1.7 Voltage test between terminals and case . 29

60252-2 Ó IEC:2010 – 3 –
6.1.8 Capacitance and power factor measurement . 30
6.1.9 Check of dimensions . 31
6.1.10 Mechanical tests . 31
6.1.11 Sealing test . 33
6.1.12 Endurance test . 33
6.1.13 Damp heat test . 35
6.1.14 Pressure relief test . 35
6.1.15 Resistance to heat, fire and tracking . 36
6.2 Overloads . 36
6.2.1 Maximum permissible voltage . 36
6.2.2 Maximum permissible current . 36
6.2.3 Maximum permissible reactive output . 37
6.3 Safety requirements . 37
6.3.1 Creepage distances and clearances . 37
6.3.2 Terminals and connecting cables . 37
6.3.3 Earth connections . 37
6.3.4 Discharge devices . 38
6.3.5 Pollution . 38
6.4 Marking . 38
7 Guidance for installation and operation . 39
7.1 General . 39
7.2 Choice of rated voltage . 39
7.2.1 Measurement of working voltage . 39
7.2.2 Influence of capacitance .
...