Hand-held motor-operated electric tools - Safety - Part 2-13: Particular requirements for chain saws
Applies to chain saws for cutting wood and designed for use by one person. This standard does not cover chain saws designed for use in conjunction with a guide-plate and riving knife or in any other way such as with a support or as a stationary or transportable machine. Does not apply to chain saws for tree service as defined in ISO 11681-2, pole cutters and pruners.
Handgeführte motorbetriebene Elektrowerkzeuge - Sicherheit - Teil 2-13: Besondere Anforderungen für Kettensägen
Outils électroportatifs à moteur - Sécurité - Partie 2-13: Règles particulières pour les scies à chaîne
S'applique aux scies à chaîne destinées à couper du bois et conçues pour être utilisées par une seule personne. Cette norme ne s'applique pas aux scies à chaîne conçues pour être utilisées conjointement avec un guide-chaîne et un couteau diviseur ou de toute autre manière telle qu'avec un support ou comme une machine fixe ou transportable. Ne s'applique pas aux scies à chaîne pour l'élagage des arbres comme défini dans l'ISO 11681-2, les scies à perche et les perches élagueuses.
Električna ročna orodja - Varnost - 2-13. del: Posebne zahteve za verižne žage (IEC 60745-2-13:2006, spremenjen)
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Handgeführte motorbetriebene Elektrowerkzeuge - Sicherheit -- Teil 2-13: Besondere Anforderungen für KettensägenOutils électroportatifs à moteur - Sécurité -- Partie 2-13: Règles particulières pour les scies à chaîneHand-held motor-operated electric tools
- Safety -- Part 2-13: Particular requirements for chain saws65.060.80Gozdarska opremaForestry equipment25.140.20Electric toolsICS:Ta slovenski standard je istoveten z:EN 60745-2-13:2009SIST EN 60745-2-13:2009en,fr,de01-december-2009SIST EN 60745-2-13:2009SLOVENSKI
STANDARDSIST EN 60745-2-13:20081DGRPHãþD
SIST EN 60745-2-13:2009
EUROPEAN STANDARD EN 60745-2-13 NORME EUROPÉENNE
EUROPÄISCHE NORM July 2009
CENELEC European Committee for Electrotechnical Standardization Comité Européen de Normalisation Electrotechnique Europäisches Komitee für Elektrotechnische Normung
Central Secretariat: Avenue Marnix 17, B - 1000 Brussels
© 2009 CENELEC -
All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 60745-2-13:2009 E
ICS 25.140.20; 65.060.80 Supersedes EN 60745-2-13:2007
Hand-held motor-operated electric tools -
Part 2-13: Particular requirements for chain saws (IEC 60745-2-13:2006, modified)
Outils électroportatifs à moteur -
Partie 2-13: Règles particulières
pour les scies à chaîne (CEI 60745-2-13:2006, modifiée)
Handgeführte motorbetriebene Elektrowerkzeuge -
Sicherheit - Teil 2-13: Besondere Anforderungen
für Kettensägen (IEC 60745-2-13:2006, modifiziert)
This European Standard was approved by CENELEC on 2009-06-01. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the Central Secretariat has the same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Cyprus, the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom.
SIST EN 60745-2-13:2009
EN 60745-2-13:2009 - 2 - Foreword The text of the International Standard IEC 60745-2-13:2006, prepared by IEC SC 61F (transformed into IEC TC 116, Safety of hand-held motor-operated electric tools), together with the common modifications prepared by the Technical Committee CENELEC TC 61F (transformed into TC 116), was submitted to the CENELEC Unique Acceptance Procedure and was approved by CENELEC as EN 60745-2-13 on 2007-03-01. A draft amendment (prAB), extending Annex ZZ to include the new MD 2006/42/EC, was submitted to the formal vote. The combined texts were approved by CENELEC as a new edition of EN 60745-2-13 on 2009-06-01. This European Standard supersedes EN 60745-2-13:2007. The following dates were fixed: – latest date by which the EN has to be implemented at national level by publication of an identical national standard or by endorsement
2009-12-29 – latest date by which the national standards conflicting with the EN have to be withdrawn
2009-12-29 This standard is divided into two parts: Part 1: General requirements which are common to most hand-held electric motor operated tools (for the purpose of this standard referred to simply as tools) which could come within the scope of this standard; Part 2: Requirements for particular types of tools which either supplement or modify the requirements given in Part 1 to account for the particular hazards and characteristics of these specific tools. This European Standard has been prepared under a mandate given to CENELEC by the European Commission and the European Free Trade Association and covers essential requirements of EC Directives 98/37/EC (Machinery Directive), amended by Directive 98/79/EC, and 2006/42/EC. See Annexes ZZA and ZZB. Compliance with the clauses of Part 1 together with this Part 2 provides one means of conforming with the essential health and safety requirements of the Directives concerned. CEN/TC 144 is producing standards for non-electric chain saws (EN 608). Warning: Other requirements and other EC Directives can be applicable to the products falling within the scope of this standard. This standard follows the overall requirements of EN ISO 12100-1 and EN ISO 12100-2. This Part 2-13 is to be used in conjunction with EN 60745-1:2009. When this standard states "addition", "modification" or "replacement", the relevant text in Part 1 is to be adapted accordingly. Subclauses, items, tables and figures which are additional to those in Part 1 are numbered starting from 101. SIST EN 60745-2-13:2009
- 3 - EN 60745-2-13:2009 Subclauses, notes, tables and figures which are additional to those in IEC 60745-2-13:2006 are prefixed “Z”. Annexes ZA, ZZA and ZZB have been added by CENELEC. NOTE In this standard the following print types are used:
- requirements proper; in roman type
- test specifications: in italic type;
- explanatory matter: in smaller roman type. __________
SIST EN 60745-2-13:2009
EN 60745-2-13:2009 - 4 - Endorsement notice The text of the International Standard IEC 60745-2-13:2006 was approved by CENELEC as a European Standard with agreed common modifications as given below. COMMON MODIFICATIONS 1 Scope Add: The chain saws covered by this standard are designed only to be operated with the right hand on the rear handle and the left hand on the front handle. 2 Normative references Replace the reference to ISO 3864-3 by: ISO 3864-3:2006, Graphical symbols – Safety colours and safety signs – Part 3: Design principles for graphical symbols for use in safety signs
Add: ISO 22868:2005, Forestry machinery – Noise test code for portable hand-held machines with an internal combustion engine – Engineering method (Grade 2 accuracy) 6 Void Replace by: 6 Environmental requirements This clause of Part 1 is applicable, except as follows: 188.8.131.52 Replacement: The sound power level shall be measured according to EN ISO 3744, where the acoustic environment, instrumentation, quantities to be measured, quantities to be determined, and the measurement procedure are specified. The sound power level shall be given as A-weighted sound power level in dB reference 1 pW. The A-weighted sound pressure levels, from which the sound power is to be determined, shall be measured directly, and not calculated from frequency band data.
The sound power level shall be determined according to Clause 5 of EN ISO 22868, with the test environment, measurement surface and six microphone positions specified there and in Clause 6 of EN ISO 22868. SIST EN 60745-2-13:2009
- 5 - EN 60745-2-13:2009 The A-weighted sound power level, LWA, shall be calculated, in accordance with 8.6 of EN ISO 3744, as follows:
)10lg(0pfAWASSLL+=, in dB (Z101) with pfAL determined from
2A1A61i0,1pfAipA,106110lgKKLL−−=∑=′ where pfAL is the A-weighted surface sound pressure level according to EN ISO 3744 ipA,L′ A-weighted sound pressure level measured at the i-th microphone position, in decibels AK1 background noise correction, A-weighted AK2 environmental correction, A-weighted S area of the measurement surface, in m² 0S = 1 m² If the test environment meets the requirements of EN ISO 22868, then the environmental correction factor K2A shall be considered as negligible. For the hemispherical measurement surface, the area S of the measurement surface is calculated as follows: S = 2π r²,
in m². (Z102) where r, the radius of the hemisphere, is 4 m as specified in Clause 5 of EN ISO 22868. 184.108.40.206 Modification: The installation and mounting conditions shall be in accordance with A.1 and A.2 of EN ISO 22868, as far as applicable to electric chain saws. The ambient conditions shall be as specified in 6.1 of EN ISO 22868. 220.127.116.11 Modification: Chain saws are tested under the two operating conditions “idling” and “full load” in accordance with A.3.1 of EN ISO 22868. “Idling” shall be operation at no-load, with maximum speed settings. “Full load” shall be in accordance with A.3.3 of EN ISO 22868, with maximum speed settings. SIST EN 60745-2-13:2009
EN 60745-2-13:2009 - 6 - Four consecutive tests for “idling” and four for “full load” shall be carried out, with each sound power level determined in accordance with the procedure stated in A.3.1 of EN ISO 22868. With LW1 and LW2 being the average sound power levels of the two different modes of operation defined above, the resulting sound power level LWA is calculated by:
10 21 lg 10LLL+= 18.104.22.168 Location of the measurement Addition: Figure Z101 shows the positions on the front handle and rear handle. 22.214.171.124 Operating conditions Chain saws are tested under load observing the conditions shown in Table Z101. Table Z101 – Test conditions Material Freshly felled softwood log of local timber, not frozen. Width of the log to be trimmed to 75 % of the usable cutting length of the guide bar Orientation Log to be rigidly clamped horizontally so that the centre line of the log is at 0,6 m from the ground Tool bit Saw chain to be as supplied or recommended by the manufacturer Feed force Sufficient force, using the spiked bumper, to achieve rated input ± 10 % Test cycle Cutting across the width of the log in a part substantially free of knots
126.96.36.199 Declaration of the vibration total value Addition: The vibration total value ah of the handle with the highest emission and the uncertainty K shall be declared. 8 Marking and instructions 188.8.131.52 Remove the note after the 2nd indent. 21 Construction Add the following subclause: 21.Z1 This subclause of Part 1 is not applicable. SIST EN 60745-2-13:2009
- 7 - EN 60745-2-13:2009 Add the following new figure:
Figure Z101 - Position of transducers SIST EN 60745-2-13:2009
EN 60745-2-13:2009 - 8 - Add the following annexes: Annex ZA (normative)
Normative references to international publications with their corresponding European publications The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
Where an International Publication has been modified by common modifications, indicated by (mod), the relevant EN/HD applies. Publication Year Title EN/HD Year ISO 3864-3 2006 Graphical symbols - Safety colours and safety signs -
Part 3: Design principles for graphical symbols for use in safety signs - - ISO 6533 2001 Forestry machinery - Portable chain-saw front hand-guard - Dimensions and clearances - - ISO 6534 1992 Portable chain-saw - Hand-guards - Mechanical strength - - ISO 7914 2002 Forestry machinery - Portable chain-saws - Minimum handle clearance and sizes - - ISO 7915 1991 Forestry machinery - Portable chain-saws - Determination of handle strength - - ISO 8334 1985 Forestry machinery - Portable chain-saws - Determination of balance - - ISO 9518 1998 Forestry machinery - Portable chain-saws - Kickback test - - ISO 10726 1992 Portable chain saws - Chain catcher - Dimensions and mechanical strength - - ISO 11681-2 1998 Machinery for forestry - Portable chain-saws - Safety requirements and testing - Part 2: Chain-saws for tree service EN ISO 11681-2 1998 ISO 22868 2005 Forestry machines - Noise test code for portable hand-held machines with an internal combustion engine - Engineering method (Grade 2 accuracy) EN ISO 22868 2008
SIST EN 60745-2-13:2009
- 9 - EN 60745-2-13:2009 Annex ZZ (informative)
Coverage of Essential Requirements of EC Directives Annex ZZA (informative)
Coverage of Essential Requirements of Directive 98/37/EC This European Standard has been prepared under a mandate given to CENELEC by the European Commission and the European Free Trade Association and within its scope the standard covers all relevant Essential Requirements as given in EC Directive 98/37/EC (Machinery Directive), amended by Directive 98/79/EC.
Compliance with this standard provides one means of conformity with the specified essential requirements of the Directives concerned.
WARNING: Other requirements and other EC Directives may be applicable to the products falling within the scope of this standard. Annex ZZB (informative)
Coverage of Essential Requirements of Directive 2006/42/EC This European Standard has been prepared under a mandate given to CENELEC by the European Commission and the European Free Trade Association and within its scope the standard covers all relevant Essential Requirements as given in EC Directive 2006/42/EC (Machinery Directive).
Compliance with this standard provides one means of conformity with the specified essential requirements of the Directive concerned.
WARNING: Other requirements and other EC Directives may be applicable to the products falling within the scope of this standard.
__________ SIST EN 60745-2-13:2009
SIST EN 60745-2-13:2009
NORME INTERNATIONALECEIIEC INTERNATIONAL STANDARD 60745-2-13Deuxième éditionSecond edition2006-03 Outils électroportatifs à moteur – Sécurité – Partie 2-13: Règles particulières pour les scies à chaîne
Hand-held motor-operated electric tools – Safety – Part 2-13: Particular requirements for chain saws
Pour prix, voir catalogue en vigueur For price, see current catalogue IEC 2006
Droits de reproduction réservés
Copyright - all rights reserved Aucune partie de cette publication ne peut être reproduite ni utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie et les microfilms, sans l'accord écrit de l'éditeur. No part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from the publisher. International Electrotechnical Commission,
3, rue de Varembé, PO Box 131, CH-1211 Geneva 20, SwitzerlandTelephone: +41 22 919 02 11 Telefax: +41 22 919 03 00 E-mail: firstname.lastname@example.org
Web: www.iec.ch CODE PRIX PRICE CODE V Commission Electrotechnique InternationaleInternational Electrotechnical CommissionSIST EN 60745-2-13:2009
60745-2-13 IEC:2006 – 3 – CONTENTS FOREWORD.7 1 Scope.13 2 Normative references.13 3 Terms and definitions.15 4 General requirements.17 5 General conditions for the tests.17 6 Void.17 7 Classification.17 8 Marking and instructions.19 9 Protection against access to live parts.23 10 Starting.23 11 Input and current.23 12 Heating.23 13 Leakage current.25 14 Moisture resistance.25 15 Electric strength.25 16 Overload protection of transformers and associated circuits.25 17 Endurance.25 18 Abnormal operation.25 19 Mechanical hazards.25 20 Mechanical strength.33 21 Construction.33 22 Internal wiring.37 23 Components.37 24 Supply connection and external flexible cords.37 25 Terminals for external conductors.37 26 Provision for earthing.37 27 Screws and connections.37 28 Creepage distances, clearances and distances through insulation.37 29 Resistance to heat, fire and tracking.37 30 Resistance to rusting.37 31 Radiation, toxicity and similar hazards.37
Annexes.51 Annex K (normative)
Battery tools and battery packs.51 Annex L (normative)
Battery tools and battery packs provided with mains connection or non-isolated sources.51 Annex AA (normative)
Symbols for safety recommendations and warnings.53 Annex BA (informative)
Instructions concerning the proper techniques for basic felling, limbing, and cross-cutting.55
Bibliography.65 SIST EN 60745-2-13:2009
60745-2-13 IEC:2006 – 5 –
Figure 101 – Chain saw nomenclature.39 Figure 102 – Cutting length.41 Figure 103 – Holding the chain saw.41 Figure 104 – Minimum rear hand guard dimensions.43 Figure 105 – Straight test probe.43 Figure 106 – Chain brake test.45 Figure 107 – Static test for release force.47 Figure 108 – Bar tip guard.47 Figure 109 – Handle gripping area.49 Figure 110 – Impact text fixture for handle insulation.49 Figure BB.101 – Description of felling: escape routes.59 Figure BB.102 – Description of felling: undercutting.59 Figure BB.103 – Tree limbing.61 Figure BB.104 – Log supported along the entire length.61 Figure BB.105 – Log supported one end.61 Figure BB.106 – Log supported both ends.63 Figure BB.107 – Bucking a log.63
SIST EN 60745-2-13:2009
60745-2-13 IEC:2006 – 7 – INTERNATIONAL ELECTROTECHNICAL COMMISSION ____________
HAND-HELD MOTOR-OPERATED ELECTRIC TOOLS – SAFETY–
Part 2-13: Particular requirements for chain saws
FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non-governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any equipment declared to be in conformity with an IEC Publication. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. International Standard IEC 60745-2-13 has been prepared by subcommittee 61F: Safety of hand-held motor-operated electric tools, of IEC technical committee 61: Safety of household and similar electrical appliances. This second edition cancels and replaces the first edition published in 1989. This edition constitutes a technical revision. Main changes include Clause 8: Markings and instructions, introducing detailed safety warnings; Clause 19: Mechanical hazards, with requirements for handles, hand guards, guarding of moving parts, chain catcher, spiked bumper, chain brake, computed kickback angle, guide bar cover, saw chain tension, oiler, balance and run down time; Clause 20: Mechanical strength, with requirements for handles and hand guards; Clause 21: Construction, with requirements for the insulation of knobs and handles. SIST EN 60745-2-13:2009
60745-2-13 IEC:2006 – 9 – The text of this standard is based on the following documents: FDIS Report on voting 61F/625/FDIS 61F/637/RVD
Full information on the voting for the approval of this standard can be found in the report on voting indicated in the above table. This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. This part 2 is to be used in conjunction with the latest edition of IEC 60745-1, Hand-held motor-operated electric tools – Safety – Part 1: General requirements, and its amendments. It was established on the basis of the fourth edition (2006) of that standard.
NOTE 1 When “Part 1” is mentioned in this standard, it refers to IEC 60745-1. This part 2 supplements or modifies the corresponding clauses of IEC 60745-1, so as to convert that publication into the IEC standard: Safety requirements for chain saws.
When a particular subclause of Part 1 is not mentioned in this part 2, that subclause applies as far as is reasonable. When this standard states “addition”, “modification” or “replacement”, the relevant text in Part 1 is to be adapted accordingly.
NOTE 2 The following numbering system is used: – subclauses, items, tables and figures that are numbered starting from 101 are additional to those in Part 1; – additional annexes are lettered AA, BB, etc. NOTE 3 In this standard, the following print types are used: – requirements: in roman type;
– test specifications: in italic type; – notes: in smaller roman type. IEC 60745 consists of the following parts, under the general title Hand-held motor-operated electric tools – Safety: Part 1: General requirements Part 2-1: Particular requirements for drills and impact drills Part 2-2: Particular requirements for screwdrivers and impact wrenches Part 2-3: Particular requirements for grinders, polishers and disk-type sanders Part 2-4: Particular requirements for sanders and polishers other than disk type Part 2-5: Particular requirements for circular saws
Part 2-6: Particular requirements for hammers Part 2-7: Particular requirements for spray guns for non-flammable liquids Part 2-8: Particular requirements for shears and nibblers Part 2-9: Particular requirements for tappers Part 2-11: Particular requirements for reciprocating saws (jig and sabre saws) Part 2-12: Particular requirements for concrete vibrators SIST EN 60745-2-13:2009
60745-2-13 IEC:2006 – 11 – Part 2-13: Particular requirements for chain saws Part 2-14: Particular requirements for planers Part 2-15: Particular requirements for hedge trimmers
Part 2-16: Particular requirements for tackers Part 2-17: Particular requirements for routers and trimmers Part 2-18: Particular requirements for strapping tools Part 2-19: Particular requirements for jointers
Part 2-20: Particular requirements for band saws Part 2-21: Particular requirements for drain cleaners
The committee has decided that the contents of this publication will remain unchanged until the maintenance result date indicated on the IEC web site under "http://webstore.iec.ch" in the data related to the specific publication. At this date, the publication will be • reconfirmed; • withdrawn; • replaced by a revised edition, or • amended.
SIST EN 60745-2-13:2009
60745-2-13 IEC:2006 – 13 – HAND-HELD MOTOR-OPERATED ELECTRIC TOOLS – SAFETY
Part 2-13: Particular requirements for chain saws
1 Scope This clause of Part 1 is applicable, except as follows: Addition: This standard applies to chain saws for cutting wood and designed for use by one person. This standard does not cover chain saws designed for use in conjunction with a guide-plate and riving knife or in any other way such as with a support or as a stationary or transportable machine. This standard does not apply to chain saws for tree service as defined in ISO 11681-2, pole cutters and pruners. 2 Normative references This clause of Part 1 is applicable, except as follows: Addition: ISO 3864-31), Graphical sym