EN 61340-5-1:2016

Electrostatics - Part 5-1: Protection of electronic devices from electrostatic phenomena - General requirements

Applies to activities that: manufacture, process, assemble, install, package, label, service, test, inspect, transport or otherwise handle electrical or electronic parts, assemblies and equipment susceptible to damage by electrostatic discharges greater than or equal to 100 V human body model (HBM). Provides the requirements for an ESD control program. The user should refer to IEC 61340-5-2 for guidance on the implementation of this standard. Does not apply to electrically initiated explosive devices, flammable liquids, gases and powders. The purpose of this standard is to provide the administrative and technical requirements for establishing, implementing and maintaining an ESD control program (hereinafter referred to as the 'program'). The main changes with respect to the previous edition are listed below: This version of IEC 61340-5-1 focuses on the requirements for an ESD control program. In addition, this version of IEC 61340-5-1 has been aligned with other major ESD control program standards used throughout the world.

Elektrostatik - Teil 5-1: Schutz von elektronischen Bauelementen gegen elektrostatische Phänomene - Allgemeine Anforderungen

Electrostatique - Partie 5-1: Protection des dispositifs électroniques contre les phénomènes électrostatiques - Exigences générales

La présente partie de la CEI 61340 s'applique aux activités concernant: la fabrication, le traitement, l'assemblage, l'installation, l'emballage, l'étiquetage, l'entretien, l'essai, l'examen, le transport ou bien la manipulation des parties, des ensembles et des équipements électriques ou électroniques susceptibles d'être endommagés par des décharges électrostatiques supérieures ou égales à 100 V sur le modèle du corps humain (HBM). Cette norme fournit les exigences nécessaires à un programme de contrôle ESD. Il convient que l'utilisateur se réfère à la CEI 61340-5-2 comme lignes directrices pour l'application de cette norme. Cette norme ne s'applique pas aux dispositifs explosifs provoqués électriquement, aux liquides, gaz et poudres inflammables. La présente norme a pour but de fournir les exigences administratives et techniques pour l'établissement, la mise en uvre et l'entretien d'un programme de contrôle des ESD (désigné ici comme le 'programme'). Les modifications principales par rapport à l'édition précédente sont les suivantes: Cette version de la CEI 61340-5-1 porte sur les exigences nécessaires à un programme de contrôle ESD. De plus, cette version de la CEI 61340-5-1 a été alignée sur d'autres normes de programmes de contrôle ESD utilisées à travers le monde

Elektrostatika - 5-1. del: Zaščita elektronskih naprav pred elektrostatskimi pojavi - Splošne zahteve (IEC 61340-5-1:2016)

Uporablja se za dejavnosti, s katerimi se izdeluje, obdeluje, sestavlja, namešča, pakira, označuje, servisira, preskuša, pregleduje, prevaža ali drugače upravlja električne ali elektronske dele, sestave in opremo, ki se lahko poškodujejo pod vplivom elektrostatičnih izpraznitev, višjih ali enakih 100 V po modelu človeškega telesa (HBM).   Zagotavlja zahteve za nadzorni program ESD.  Uporabnik naj bi za izvajanje tega standarda uporabljal dokument IEC 61340-5-2. Ne uporablja se za elektronsko sprožene eksplozivne naprave, vnetljive tekočine, pline in praške. Namen tega standarda je zagotavljanje administrativnih in tehničnih zahtev za vzpostavljanje, uvajanje in vzdrževanje nadzornega programa ESD (v nadaljevanju program). Spodaj so navedene glavne spremembe glede na predhodno različico: Ta različica standarda IEC 61340-5-1 se osredotoča na zahteve za nadzorni program ESD. Poleg tega je bila ta različica standarda IEC 61340-5-1 usklajena z drugimi glavnimi standardi za nadzorni program ESD, ki se uporabljajo po svetu.

General Information

• Status: Published
• Publication Date: 17-Nov-2016
• Withdrawal Date: 17-Nov-2019
• ICS: 17.200.99 - Other standards related to thermodynamics
• ICS: 29.020 - Electrical engineering in general
• Technical Committee: CLC/SR 101 - Electrostatics
• Drafting Committee: IEC/TC 101 - IEC_TC_101
• Current Stage: 6060 - Document made available - Publishing
• Start Date: 18-Nov-2016
• Completion Date: 18-Nov-2016
• Ref Project: SIST EN 61340-5-1:2017 - Electrostatics - Part 5-1: Protection of electronic devices from electrostatic phenomena - General requirements (IEC 61340-5-1:2016)

Relations

• Replaces: EN 61340-5-1:2007 - Electrostatics - Part 5-1: Protection of electronic devices from electrostatic phenomena - General requirements
• Effective Date: 24-Mar-2015
• Replaced By: EN IEC 61340-5-1:2024 - Electrostatics - Part 5-1: Protection of electronic devices from electrostatic phenomena - General requirements
• Effective Date: 22-Mar-2022
• Corrected By: EN 61340-5-1:2016/AC:2017-05 - Electrostatics - Part 5-1: Protection of electronic devices from electrostatic phenomena - General requirements
• Effective Date: 16-May-2017

Standards Content (Sample)

SLOVENSKI STANDARD
01-januar-2017
1DGRPHãþD
SIST EN 61340-5-1:2008
(OHNWURVWDWLNDGHO=DãþLWDHOHNWURQVNLKQDSUDYSUHGHOHNWURVWDWVNLPLSRMDYL
6SORãQH]DKWHYH,(&
Electrostatics - Part 5-1: Protection of electronic devices from electrostatic phenomena -
General requirements (IEC 61340-5-1:2016)
Elektrostatik - Teil 5-1: Schutz von elektronischen Bauelementen gegen elektrostatische
Phänomene - Allgemeine Anforderungen
Electrostatique - Partie 5-1: Protection des dispositifs électroniques contre les
phénomènes électrostatiques - Exigences générales
Ta slovenski standard je istoveten z: EN 61340-5-1:2016
ICS:
17.220.99 Drugi standardi v zvezi z Other standards related to
elektriko in magnetizmom electricity and magnetism
31.020 Elektronske komponente na Electronic components in
splošno general
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD EN 61340-5-1

NORME EUROPÉENNE
EUROPÄISCHE NORM
November 2016
ICS 17.200.99; 29.020 Supersedes EN 61340-5-1:2007
English Version
Electrostatics - Part 5-1: Protection of electronic devices from
electrostatic phenomena - General requirements
(IEC 61340-5-1:2016)
Electrostatique - Partie 5-1: Protection des dispositifs Elektrostatik - Teil 5-1: Schutz von elektronischen
électroniques contre les phénomènes électrostatiques - Bauelementen gegen elektrostatische Phänomene -
Exigences générales Allgemeine Anforderungen
(IEC 61340-5-1:2016) (IEC 61340-5-1:2016)
This European Standard was approved by CENELEC on 2016-07-01. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.

European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2016 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN 61340-5-1:2016 E
European foreword
The text of document 101/505/FDIS, future edition 2 of IEC 61340-5-1, prepared by IEC/TC 101
"Electrostatics" was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as
The following dates are fixed:
(dop) 2017-05-18
• latest date by which the document has to be implemented at
national level by publication of an identical national
standard or by endorsement
• latest date by which the national standards conflicting with (dow) 2019-11-18
the document have to be withdrawn

This document supersedes EN 61340-5-1:2007.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such
patent rights.
Endorsement notice
The text of the International Standard IEC 61340-5-1:2016 was approved by CENELEC as a
European Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standard indicated :
IEC 60749-26 NOTE Harmonized as EN 60749-26.
IEC 60749-27 NOTE Harmonized as EN 60749-27.
IEC 60364 (Series) NOTE Harmonized as EN 60364 (Series).
IEC 61010-1 NOTE Harmonized as EN 61010-1.
IEC 61140 NOTE Harmonized as EN 61140.
IEC/TR 61340-5-2 NOTE Harmonized as CLC/TR 61340-5-2.

Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.
NOTE 1 When an International Publication has been modified by common modifications, indicated by (mod), the relevant
EN/HD applies.
NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available here:
www.cenelec.eu.
Publication Year Title EN/HD Year
IEC 61340-2-3 -  Electrostatics - Part 2-3: Methods of test EN 61340-2-3 -
for determining the resistance and
resistivity of solid materials used to avoid
electrostatic charge accumulation
IEC 61340-4-1 -  Electrostatics -- Part 4-1: Standard test EN 61340-4-1 -
methods for specific applications -
Electrical resistance of floor coverings and
installed floors
IEC 61340-4-3 -  Electrostatics -- Part 4-3: Standard test EN 61340-4-3 -
methods for specific applications -
Footwear
IEC 61340-4-5 -  Electrostatics -- Part 4-5: Standard test EN 61340-4-5 -
methods for specific applications - Methods
for characterizing the electrostatic
protection of footwear and flooring in
combination with a person
IEC 61340-4-6 -  Electrostatics -- Part 4-6: Standard test EN 61340-4-6 -
methods for specific applications - Wrist
straps
IEC 61340-4-7 -  Electrostatics - Part 4-7: Standard test - -
methods for specific applications -
Ionization
IEC 61340-4-9 -  Electrostatics - Part 4-9: Standard test EN 61340-4-9 -
methods for specific applications -
Garments
IEC 61340-5-3 -  Electrostatics - Part 5-3: Protection of EN 61340-5-3 -
electronic devices from electrostatic
phenomena - Properties and requirements
classification for packaging intended for
electrostatic discharge sensitive devices

IEC 61340-5-1 ®
Edition 2.0 2016-05
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Electrostatics –
Part 5-1: Protection of electronic devices from electrostatic phenomena –

General requirements
Électrostatique –
Partie 5-1: Protection des dispositifs électroniques contre les phénomènes

électrostatiques – Exigences générales

INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 17.220.99; 29.020 ISBN 978-2-8322-3422-8

– 2 – IEC 61340-5-1:2016 © IEC 2016
CONTENTS
FOREWORD . 3
INTRODUCTION . 5
1 Scope . 7
2 Normative references. 7
3 Terms and definitions . 8
4 Personnel safety . 9
5 ESD control program . 10
5.1 General . 10
5.1.1 ESD control program requirements . 10
5.1.2 ESD coordinator . 10
5.1.3 Tailoring . 10
5.2 ESD control program administrative requirements . 10
5.2.1 ESD control program plan . 10
5.2.2 Training plan . 10
5.2.3 Product qualification . 11
5.2.4 Compliance verification plan . 11
5.3 ESD control program plan technical requirements . 11
5.3.1 General . 11
5.3.2 Grounding/equipotential bonding systems . 12
5.3.3 Personnel grounding . 14
5.3.4 ESD protected areas (EPA) . 15
5.3.5 Packaging . 17
5.3.6 Marking . 17
Annex A (normative) Test methods . 19
Bibliography . 20

Figure 1 – Schematic of an EPA with a ground reference . 13
Figure 2 – Schematic of an equipotential bonding system . 14
Figure A.1 – Footwear functional testing (example). 19

Table 1 – Grounding/bonding requirements . 14
Table 2 – Personnel grounding requirements . 15
Table 3 – EPA requirements . 17

IEC 61340-5-1:2016 © IEC 2016 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
ELECTROSTATICS –
Part 5-1: Protection of electronic devices from
electrostatic phenomena – General requirements

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upo
...