iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CLC

EN 50130-4:1995

(Main)

Alarm systems - Part 4: Electromagnetic compatibility - Product family standard: Immunity requirements for components of fire, intruder and social alarm systems

Alarm systems - Part 4: Electromagnetic compatibility - Product family standard: Immunity requirements for components of fire, intruder and social alarm systems

This EMC product-family standard, for immunity requirements, applies to the components of the following alarm systems, intended for use in and around buildings in residential, commercial, light industrial and industrial environments: Intruder alarm systems; Hold-up alarm systems; Fire detection and fire alarm systems; Social alarm systems; CCTV systems, for security applications; Access control systems, for security applications. The tests and severities to be used are the same for indoor and outdoor applications of fixed, movable and portable equipment. The levels do not cover extreme cases, which may occur in any location, but with an extremely low probability of occurrence, or in special locations close to powerful emitters (e.g. radar transmitters). Equipment within the scope of this standard should be designed in order to operate satisfactorily in the environmental electromagnetic conditions of residential, commercial, light industrial and industrial environments. This implies particularly that it should be able to operate correctly within the conditions fixed by the electromagnetic compatibility levels for the various disturbances on the low voltage public supply system as defined by ENV 61000-2-2. The Immunity tests in this standard only concern the most critical disturbance phenomena. For equipment using radio signaling, mains signaling or with connections to the public telephone system, additional requirements, from other standards specific to these signaling media, might apply. For the requirements applicable to radio links, reference should be made to the applicable ETSI standard, in accordance with the agreement between ETSI and CENELEC. This standard does not specify basic safety requirements, such as protection against electrical shocks, unsafe operation, insulation coordination and related dielectric tests. This standard does not cover EMC emission requirements. These are covered by other appropriate standards

Alarmanlagen - Teil 4: Elektromagnetische Verträglichkeit - Produktfamiliennorm: Anforderungen an die Störfestigkeit von Anlageteilen für Brand- und Einbruchmeldeanlagen sowie Personen-Hilferufanlagen

Systèmes d'alarme - Partie 4: Compatibilité électromagnétique - Norme famille de produit: Prescriptions relatives à l'immunité des composants de systèmes de détection d'incendie, d'intrusion et d'alarme sociale

Alarmni sistemi - 4. del: Elektromagnetna združljivost - Standard za varnost proizvodov - Zahteve za odpornost sestavnih komponent požarnih, vlomnih in socialnih alarmnih sistemov

General Information

Status
Withdrawn
Publication Date
04-Dec-1995
Withdrawal Date
31-Dec-2000
ICS
13.320 - Alarm and warning systems
29.020 - Electrical engineering in general
Technical Committee
CLC/TC 79 - Alarm systems
Parallel Committee
IEC/TC 79 - IEC_TC_79
Current Stage
9960 - Withdrawal effective - Withdrawal
Start Date
13-Jun-2014
Completion Date
13-Jun-2014
Directive
2004/108/EC - Directive 2004/108/EC of the European Parliament and of the Council of 15 December 2004 on the approximation of the laws of the Member States relating to electromagnetic compatibility and repealing Directive 89/336/EEC
2004/108/EU - DIRECTIVE 2004/108/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL of 15 December 2004 on the approximation of the laws of the Member States relating to electromagnetic compatibility and repealing Directive 89/336/EEC
89/336/EEC - Electromagnetic compatibility (EMC)
Mandate
BC/CLC/92-02 - BC/CLC/92-02
M/404 - Standardisation Mandate to CEN, CENELEC and ETSI for harmonized standard according to the Electro Magnetic Compatibility (EMC) Directive 2004/108/EC
Ref Project
SIST EN 50130-4:1997 - Alarm systems -- Part 4: Electromagnetic compatibility - Product family standard: Immunity requirements for components of fire, intruder and social alarm systems

Relations

Replaced By
EN 50130-4:2011 - Alarm systems - Part 4: Electromagnetic compatibility - Product family standard: Immunity requirements for components of fire, intruder, hold up, CCTV, access control and social alarm systems
Effective Date
07-Jun-2022
Amended By
EN 50130-4:1995/A1:1998 - Alarm systems - Part 4: Electromagnetic compatibility - Product family standard: Immunity requirements for components of fire, intruder and social alarm systems
Effective Date
29-Jan-2023
Amended By
EN 50130-4:1995/A2:2003 - Alarm systems - Part 4: Electromagnetic compatibility - Product family standard: Immunity requirements for components of fire, intruder and social alarm systems
Effective Date
29-Jan-2023
Revised
EN 50130-4:2011 - Alarm systems - Part 4: Electromagnetic compatibility - Product family standard: Immunity requirements for components of fire, intruder, hold up, CCTV, access control and social alarm systems
Effective Date
06-May-2014

Buy Standard

EN 50130-4:1997EN 50130-4:1997
PreviousNext
Standard
EN 50130-4:1997
English language
21 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 50130-4:1997
01-avgust-1997
Alarmni sistemi - 4. del: Elektromagnetna združljivost - Standard za varnost
proizvodov - Zahteve za odpornost sestavnih komponent požarnih, vlomnih in
socialnih alarmnih sistemov
Alarm systems -- Part 4: Electromagnetic compatibility - Product family standard:
Immunity requirements for components of fire, intruder and social alarm systems
Alarmanlagen -- Teil 4: Elektromagnetische Verträglichkeit - Produktfamiliennorm:
Anforderungen an die Störfestigkeit von Anlageteilen für Brand- und
Einbruchmeldeanlagen sowie Personen-Hilferufanlagen
Systèmes d'alarme -- Partie 4: Compatibilité électromagnétique - Norme famille de
produit: Prescriptions relatives à l'immunité des composants de systèmes de détection
d'incendie, d'intrusion et d'alarme sociale
Ta slovenski standard je istoveten z: EN 50130-4:1995
ICS:
13.320 Alarmni in opozorilni sistemi Alarm and warning systems
33.100.20 Imunost Immunity
SIST EN 50130-4:1997 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 50130-4:1997

---------------------- Page: 2 ----------------------

SIST EN 50130-4:1997

---------------------- Page: 3 ----------------------

SIST EN 50130-4:1997

---------------------- Page: 4 ----------------------

SIST EN 50130-4:1997

---------------------- Page: 5 -------------------
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CLC
EN 50130-4:2011/A1:2014(Amendment)
Alarm systems - Part 4: Electromagnetic compatibility - Product family standard: Immunity requirements for components of fire, intruder, hold up, CCTV, access control and social alarm systems
SIST EN 50130-4:2011/A1:2014

This EMC product-family standard, for immunity requirements, applies to the components of the following alarm systems, intended for use in and around buildings in residen¬tial, commercial, light industrial and industrial environments: – access control systems, for security applications; – alarm transmission systems 1); – CCTV systems, for security applications; – fire detection and fire alarm systems; – hold-up alarm systems; – intruder alarm systems; – social alarm systems; The tests and severities to be used are the same for indoor and outdoor applications of fixed, movable and portable equipment. The levels do not cover extreme cases, which may occur in any location, but with an extremely low probability of occurrence, or in special locations close to powerful emitters (e.g. radar transmitters). Equipment within the scope of this standard should be designed in order to operate satisfactorily in the environmental electromagnetic conditions of residential, commercial, light industrial and industrial environments. This implies particularly that it should be able to operate correctly within the conditions fixed by the electromagnetic compatibility levels for the various disturbances on the low voltage public supply system as defined by EN 61000 2 2. The immunity tests in this standard only concern the most critical disturbance phenomena. For equipment using radio signalling, mains signalling or with connections to the public telephone system, additional requirements, from other standards specific to these signalling media, might apply. This standard does not specify basic safety requirements, such as protection against electrical shocks, unsafe operation, insulation coordination and related dielectric tests. This standard does not cover EMC emission requirements. These are covered by other appropriate standards.

  • Amendment
    3 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 50130-5:2011(Main)
Alarm systems - Part 5: Environmental test methods
SIST EN 50130-5:2011

This European Standard specifies environmental test methods to be used for testing the system components of the following alarm systems, intended for use in and around buildings: - intruder alarm systems; - hold-up alarm systems; - social alarm systems; - CCTV systems, for security applications; - access control systems, for security applications; - alarm transmission systems 1). This European Standard specifies three equipment classes (fixed, movable & portable equipment) and four environmental classes. The environmental classes only include the general service environments envisaged for equipment installed in typical residential, commercial and industrial environments. It may be necessary for the product standard to require additional or different environmental tests or severities where a) there could be specific environmental problems (e.g. some different severities may be required for break glass detectors stuck to glass windows, due to the local extremes of temperature and humidity), b) the test exposure falls within the intended detection phenomenon of the detector (e.g. during a vibration test on a seismic detector). In order to provide reproducible test methods and to avoid the proliferation of technically similar test methods, the test procedures have been chosen, where possible, from internationally accepted standards (e.g. IEC publications). For specific guidance on these tests, reference should be made to the appropriate document, which is indicated in the relevant sub section. For more general guidance and background information on environmental testing, reference should be made to EN 60068 1 and to the EN 60068 3 series. This European Standard does not specify a) the requirements or performance criteria to be applied, which should be specified in the relevant product standard, b) special tests only applicable to a particular device (e.g. the effects of turbulent air draughts on ultrasonic movement detectors), c) basic safety requirements, such as protection against electrical shocks, unsafe operation, insulation coordination and related dielectric tests, d) tests relating to deliberate acts of damage or tampering.

  • Standard
    37 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 50130-4:2011(Main)
Alarm systems - Part 4: Electromagnetic compatibility - Product family standard: Immunity requirements for components of fire, intruder, hold up, CCTV, access control and social alarm systems
SIST EN 50130-4:2011

This EMC product-family standard, for immunity requirements, applies to the components of the following alarm systems, intended for use in and around buildings in residen¬tial, commercial, light industrial and industrial environments: – access control systems, for security applications; – alarm transmission systems 1); – CCTV systems, for security applications; – fire detection and fire alarm systems; – hold-up alarm systems; – intruder alarm systems; – social alarm systems; The tests and severities to be used are the same for indoor and outdoor applications of fixed, movable and portable equipment. The levels do not cover extreme cases, which may occur in any location, but with an extremely low probability of occurrence, or in special locations close to powerful emitters (e.g. radar transmitters). Equipment within the scope of this standard should be designed in order to operate satisfactorily in the environmental electromagnetic conditions of residential, commercial, light industrial and industrial environments. This implies particularly that it should be able to operate correctly within the conditions fixed by the electromagnetic compatibility levels for the various disturbances on the low voltage public supply system as defined by EN 61000 2 2. The immunity tests in this standard only concern the most critical disturbance phenomena. For equipment using radio signalling, mains signalling or with connections to the public telephone system, additional requirements, from other standards specific to these signalling media, might apply. This standard does not specify basic safety requirements, such as protection against electrical shocks, unsafe operation, insulation coordination and related dielectric tests. This standard does not cover EMC emission requirements. These are covered by other appropriate standards.

  • Standard
    24 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 50130-4:2011/A1:2014(Amendment)
Alarm systems - Part 4: Electromagnetic compatibility - Product family standard: Immunity requirements for components of fire, intruder, hold up, CCTV, access control and social alarm systems
SIST EN 50130-4:2011/A1:2014

This EMC product-family standard, for immunity requirements, applies to the components of the following alarm systems, intended for use in and around buildings in residen¬tial, commercial, light industrial and industrial environments: – access control systems, for security applications; – alarm transmission systems 1); – CCTV systems, for security applications; – fire detection and fire alarm systems; – hold-up alarm systems; – intruder alarm systems; – social alarm systems; The tests and severities to be used are the same for indoor and outdoor applications of fixed, movable and portable equipment. The levels do not cover extreme cases, which may occur in any location, but with an extremely low probability of occurrence, or in special locations close to powerful emitters (e.g. radar transmitters). Equipment within the scope of this standard should be designed in order to operate satisfactorily in the environmental electromagnetic conditions of residential, commercial, light industrial and industrial environments. This implies particularly that it should be able to operate correctly within the conditions fixed by the electromagnetic compatibility levels for the various disturbances on the low voltage public supply system as defined by EN 61000 2 2. The immunity tests in this standard only concern the most critical disturbance phenomena. For equipment using radio signalling, mains signalling or with connections to the public telephone system, additional requirements, from other standards specific to these signalling media, might apply. This standard does not specify basic safety requirements, such as protection against electrical shocks, unsafe operation, insulation coordination and related dielectric tests. This standard does not cover EMC emission requirements. These are covered by other appropriate standards.

  • Amendment
    3 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 50130-5:2011(Main)
Alarm systems - Part 5: Environmental test methods
SIST EN 50130-5:2011

This European Standard specifies environmental test methods to be used for testing the system components of the following alarm systems, intended for use in and around buildings: - intruder alarm systems; - hold-up alarm systems; - social alarm systems; - CCTV systems, for security applications; - access control systems, for security applications; - alarm transmission systems 1). This European Standard specifies three equipment classes (fixed, movable & portable equipment) and four environmental classes. The environmental classes only include the general service environments envisaged for equipment installed in typical residential, commercial and industrial environments. It may be necessary for the product standard to require additional or different environmental tests or severities where a) there could be specific environmental problems (e.g. some different severities may be required for break glass detectors stuck to glass windows, due to the local extremes of temperature and humidity), b) the test exposure falls within the intended detection phenomenon of the detector (e.g. during a vibration test on a seismic detector). In order to provide reproducible test methods and to avoid the proliferation of technically similar test methods, the test procedures have been chosen, where possible, from internationally accepted standards (e.g. IEC publications). For specific guidance on these tests, reference should be made to the appropriate document, which is indicated in the relevant sub section. For more general guidance and background information on environmental testing, reference should be made to EN 60068 1 and to the EN 60068 3 series. This European Standard does not specify a) the requirements or performance criteria to be applied, which should be specified in the relevant product standard, b) special tests only applicable to a particular device (e.g. the effects of turbulent air draughts on ultrasonic movement detectors), c) basic safety requirements, such as protection against electrical shocks, unsafe operation, insulation coordination and related dielectric tests, d) tests relating to deliberate acts of damage or tampering.

  • Standard
    37 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 50130-4:2011(Main)
Alarm systems - Part 4: Electromagnetic compatibility - Product family standard: Immunity requirements for components of fire, intruder, hold up, CCTV, access control and social alarm systems
SIST EN 50130-4:2011

This EMC product-family standard, for immunity requirements, applies to the components of the following alarm systems, intended for use in and around buildings in residen¬tial, commercial, light industrial and industrial environments: – access control systems, for security applications; – alarm transmission systems 1); – CCTV systems, for security applications; – fire detection and fire alarm systems; – hold-up alarm systems; – intruder alarm systems; – social alarm systems; The tests and severities to be used are the same for indoor and outdoor applications of fixed, movable and portable equipment. The levels do not cover extreme cases, which may occur in any location, but with an extremely low probability of occurrence, or in special locations close to powerful emitters (e.g. radar transmitters). Equipment within the scope of this standard should be designed in order to operate satisfactorily in the environmental electromagnetic conditions of residential, commercial, light industrial and industrial environments. This implies particularly that it should be able to operate correctly within the conditions fixed by the electromagnetic compatibility levels for the various disturbances on the low voltage public supply system as defined by EN 61000 2 2. The immunity tests in this standard only concern the most critical disturbance phenomena. For equipment using radio signalling, mains signalling or with connections to the public telephone system, additional requirements, from other standards specific to these signalling media, might apply. This standard does not specify basic safety requirements, such as protection against electrical shocks, unsafe operation, insulation coordination and related dielectric tests. This standard does not cover EMC emission requirements. These are covered by other appropriate standards.

  • Standard
    24 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 61169-70:2024(Main)
Radio-frequency connectors - Part 70: Sectional specification for series HD-BNC radio-frequency coaxial connectors - Characteristic Impedance 75 Ω
SIST EN IEC 61169-70:2024

IEC 61169-70:2024, which is a sectional specification (SS), provides information and rules for the preparation of detail specifications (DS) of HD-BNC series RF coaxial connectors together with the pro forma blank detail specification. HD-BNC series connectors with characteristic impedance of 75 Ω are used with RF cables or micro-strips in microwave, telecommunication, wireless and other fields. The operating frequency limit is up to 18 GHz. It also prescribes mating face dimensions for general purpose connectors, gauging information and tests selected from IEC 61169-1, applicable to all detail specifications relating to series HD-BNC RF connectors. This specification indicates the recommended performance characteristics to be considered when writing a detail specification and it covers test schedules and inspection requirements for assessment levels M and H.

  • Draft
    25 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 61300-2-44:2024(Main)
Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-44: Tests - Flexing of the strain relief of fibre optic devices and components
SIST EN IEC 61300-2-44:2024

IEC 61300-2-44:2024 specifies a test to determine the influence of flexing under tensile load of the strain relief of fibre optic interconnecting devices or components. The intention is to simulate the number of flexing cycles which would typically be experienced during service life. This test is applied to both single fibre cable and multiple fibre cable. This fourth edition cancels and replaces the third edition published in 2013. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: a) replaced active monitoring with transient loss for measurements during test; b) harmonized recommended severities according to IEC 61753-1.

  • Draft
    9 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 63305:2024(Main)
Underwater acoustics - Calibration of acoustic wave vector receivers in the frequency range 5 Hz to 10 kHz
SIST EN IEC 63305:2024

IEC 63305:2024 specifies methods and procedures for calibration of vector receivers in the frequency range 5 Hz to 10 kHz, which are applicable to vector receivers based on the two different principles. In addition, it describes an absolute method of inertial vector receiver calibration in air using optical interferometry. Usually, acoustic wave vector receivers are designed and constructed based on one of two principles. One is the sound pressure difference (gradient) principle. When measuring with this sensor, the vector receiver is rigidly fixed on a mount and supported in water. The other is the co-vibrating (inertial) principle. When measuring with this sensor, the vector receiver is suspended on a mount and supported in water in a non-rigid manner, which allows the vector receiver co-vibrate in the same direction as the sound particle in the sound wave field. Many methods have been used to calibrate vector receivers, such as free-field calibration, calibration in standing wave tube and calibration in a travelling wave tube.

  • Draft
    55 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 60704-2-14:2013/A2:2024(Amendment)
Household and similar electrical appliances - Test code for the determination of airborne acoustical noise - Part 2-14: Particular requirements for refrigerators, frozen-food storage cabinets and food freezers
SIST EN 60704-2-14:2013/A2:2024
  • Draft
    4 pages
    English language
    sale 10% off
    e-Library read for
    1 day