iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CLC

HD 631.1 S1:1998

(Main)

Material characterisation - Part 1: Compounds for use in cable accessories: Resinous compounds before cure and in the cured state

Material characterisation - Part 1: Compounds for use in cable accessories: Resinous compounds before cure and in the cured state

Superseded by HD 631.1 S2:2007

Materialcharakterisierung - Teil 1: Vergußmassen für die Anwendung in Kabelgarnituren: Gießharzmassen vor dem Aushärten und im ausgehärteten Zustand

Caractérisation des matériaux - Partie 1: Matières de remplissage des accessoires de câbles: Composés résineux avant et après polymérisation

Material characterisation – Part 1: Compounds for use in cable accessories: Resinous compounds before cure and in the cured state

General Information

Status
Withdrawn
Publication Date
18-May-1998
ICS
29.040.20 - Insulating gases
29.060.20 - Cables
Technical Committee
CLC/TC 20 - Electric cables
Drafting Committee
IEC/TC 20 - IEC_TC_20
Parallel Committee
IEC/TC 20 - IEC_TC_20
Current Stage
9960 - Withdrawal effective - Withdrawal
Start Date
01-Sep-2010
Completion Date
01-Sep-2010
Ref Project
SIST HD 631.1 S1:2002 - Material characterisation -- Part 1: Compounds for use in cable accessories: Resinous compounds before cure and in the cured state

Relations

Replaced By
HD 631.1 S2:2007 - Electric cables - Accessories - Material characterisation - Part 1: Fingerprinting and type tests for resinous compounds
Effective Date
29-Jan-2023

Buy Standard

HD 631.1 S1:2002HD 631.1 S1:2002
PreviousNext
Standardization document
HD 631.1 S1:2002
English language
14 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
HD 631.1 S1:1999HD 631.1 S1:1999
PreviousNext
Standardization document
HD 631.1 S1:1999
English language
14 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST HD 631.1 S1:
01-QRYHPEHU
Material characterisation – Part 1: Compounds for use in cable accessories:
Resinous compounds before cure and in the cured state
Material characterisation -- Part 1: Compounds for use in cable accessories: Resinous
compounds before cure and in the cured state
Materialcharakterisierung -- Teil 1: Vergußmassen für die Anwendung in
Kabelgarnituren: Gießharzmassen vor dem Aushärten und im ausgehärteten Zustand
Caractérisation des matériaux -- Partie 1: Matières de remplissage des accessoires de
câbles: Composés résineux avant et après polymérisation
Ta slovenski standard je istoveten z: HD 631.1 S1:1998
ICS:
29.035.20 3ODVWLþQLLQJXPHQLL]RODFLMVNL Plastics and rubber insulating
PDWHULDOL materials
29.060.20 Kabli Cables
SIST HD 631.1 S1: en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST HD 631.1 S1:2002

---------------------- Page: 2 ----------------------

SIST HD 631.1 S1:2002

------------------
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CLC
HD 621 S1:1996/A1:2001(Amendment)
Medium voltage impregnated paper insulated distribution cables
SIST HD 621 S1:1998/A1:2002

2021: CLC legacy converted by DCLab NISOSTS

  • Amendment
    39 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
HD 621 S1:1996(Main)
Medium voltage impregnated paper insulated distribution cables
SIST HD 621 S1:1998

HD 621 applies to impregnated paper insulated cables for rated voltages Uo/U(Uml from 3,6/6(7,2)kV up to 20,8/36(42)kV used in power distribution systems. This part (Part 1) specifies the general requirements applicable to these cables, unless otherwise specified in the particular sections of this H D. Test methods specified are given in HD 605, EN 60811, HD 383 and HD 405 and in IEC 55-1 and IEC 229. Part 2 covers all those test methods which are specific to paper insulated cables, and not included in HD 605. The particular types of cables are specified in Parts 3 and 4.

  • Standardization document
    776 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
HD 621 S1:1996/A1:2001(Amendment)
Medium voltage impregnated paper insulated distribution cables
SIST HD 621 S1:1998/A1:2002

2021: CLC legacy converted by DCLab NISOSTS

  • Amendment
    39 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
HD 621 S1:1996(Main)
Medium voltage impregnated paper insulated distribution cables
SIST HD 621 S1:1998

HD 621 applies to impregnated paper insulated cables for rated voltages Uo/U(Uml from 3,6/6(7,2)kV up to 20,8/36(42)kV used in power distribution systems. This part (Part 1) specifies the general requirements applicable to these cables, unless otherwise specified in the particular sections of this H D. Test methods specified are given in HD 605, EN 60811, HD 383 and HD 405 and in IEC 55-1 and IEC 229. Part 2 covers all those test methods which are specific to paper insulated cables, and not included in HD 605. The particular types of cables are specified in Parts 3 and 4.

  • Standardization document
    776 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 50566:2017/A1:2023(Amendment)
Product standard to demonstrate the compliance of wireless communication devices with the basic restrictions and exposure limit values related to human exposure to electromagnetic fields in the frequency range from 30 MHz to 6 GHz: hand-held and body mounted devices in close proximity to the human body
SIST EN 50566:2018/oprA1:2020

This product standard applies to wireless communication devices used at distances up to and including 200 mm from the human body, i.e. when held in the hand or in front of the face, mounted on the body, combined with other transmitting or non-transmitting devices or accessories (e.g. belt-clip, camera or Bluetooth add-on), or integrated into garments. The applicable frequency range is from 30 MHz to 6 GHz. The objective of this standard is to demonstrate the compliance of such devices with the basic restrictions and exposure limit values related to human exposure to radio frequency electromagnetic fields. For devices used next to the ear the applicable product standard is EN 50360:2017 [1]. For low power devices the applicable product standard is EN 50663:2017 [2].

  • Draft
    4 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 50360:2017/A1:2023(Amendment)
Product standard to demonstrate the compliance of wireless communication devices, with the basic restrictions and exposure limit values related to human exposure to electromagnetic fields in the frequency range from 300 MHz to 6 GHz: devices used next to the ear
SIST EN 50360:2018/oprA1:2020

This product standard applies to wireless communication devices used in close proximity to the human ear (e.g. mobile phones, wireless headsets). The applicable frequency range is from 300 MHz to 6 GHz. The objective of this standard is to demonstrate the compliance of such devices with the basic restrictions and exposure limit values related to human exposure to radio frequency electromagnetic fields. For devices used next to the body or in front of the face the applicable product standard is EN 50566:2017. For low power devices the applicable product standard is EN 50663:2017.

  • Draft
    3 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 60061-2:1993/A59:2023(Main)
Lamp caps and holders together with gauges for the control of interchangeability and safety - Part 2: Lampholders
SIST EN 60061-2:1999/A59:2023
  • Draft
    2 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 62351-3:2023(Main)
Power systems management and associated information exchange - Data and communications security - Part 3: Communication network and system security - Profiles including TCP/IP
SIST EN IEC 62351-3:2023

IEC 62351-3:2023 specifies how to provide confidentiality, integrity protection, and message level authentication for protocols that make use of TCP/IP as a message transport layer and utilize Transport Layer Security when cyber-security is required. This may relate to SCADA and telecontrol protocols, but also to additional protocols if they meet the requirements in this document. IEC 62351-3 specifies how to secure TCP/IP-based protocols through constraints on the specification of the messages, procedures, and algorithms of Transport Layer Security (TLS) (TLSv1.2 defined in RFC 5246, TLSv1.3 defined in RFC 8446). In the specific clauses, there will be subclauses to note the differences and commonalities in the application depending on the target TLS version. The use and specification of intervening external security devices (e.g., "bump-in-the-wire") are considered out-of-scope. In contrast to previous editions of this document, this edition is self-contained in terms of completely defining a profile of TLS. Hence, it can be applied directly, without the need to specify further TLS parameters, except the port number, over which the communication will be performed. Therefore, this part can be directly utilized from a referencing standard and can be combined with further security measures on other layers. Providing the profiling of TLS without the need for further specifying TLS parameters allows declaring conformity to the described functionality without the need to involve further IEC 62351 documents. This document is intended to be referenced as a normative part of other IEC standards that have the need for providing security for their TCP/IP-based protocol exchanges under similar boundary conditions. However, it is up to the individual protocol security initiatives to decide if this document is to be referenced. The document also defines security events for specific conditions, which support error handling, security audit trails, intrusion detection, and conformance testing. Any action of an organization in response to events to an error condition described in this document are beyond the scope of this document and are expected to be defined by the organization’s security policy. This document reflects the security requirements of the IEC power systems management protocols. Should other standards bring forward new requirements, this document may need to be revised. This second edition cancels and replaces the first edition published in 2014, Amendment 1:2018 and Amendment 2:2020. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: a) Inclusion of the TLSv1.2 related parameter required in IEC 62351-3 Ed.1.2 to be specified by the referencing standard. This comprises the following parameter: • Mandatory TLSv1.2 cipher suites to be supported. • Specification of session resumption parameters. • Specification of session renegotiation parameters. • Revocation handling using CRL and OCSP. • Handling of security events. b) Inclusion of a TLSv1.3 profile to be applicable for the power system domain in a similar way as for TLSv1.2 session.

  • Standard
    52 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 60728-101-1:2023(Main)
Cable networks for television signals, sound signals and interactive services - Part 101-1: RF cabling for two-way home networks with all-digital channels load
SIST EN IEC 60728-101-1:2023

IEC 60728-101-1:2023 provides the requirements and describes the implementation guidelines of RF cabling for two-way home networks; it is applicable to any home network that distributes signals provided by CATV/MATV/SMATV cable networks (including individual receiving systems) having a coaxial cable output. It is also applicable to home networks where some part of the distribution network uses wireless links, for example in place of the receiver cord. This part of IEC 60728 is therefore applicable to RF cabling for two-way home networks with wired cords or wireless links inside a room and primarily intended for television and sound signals operating between about 5 MHz and 3 300 MHz. The frequency range is extended to 6 000 MHz for distribution techniques that replace wired cords with a wireless two-way communication inside a room (or a small number of adjacent rooms) that uses the 5 GHz to 6 GHz band. In a building divided into apartment blocks, the distribution of the signals inside the home starts from the home network interface (HNI) up to the system outlet or terminal input. The requirements at the system outlet are given in IEC 60728-101:2016, Clause 5 and the requirements at the HNI are given in IEC 60728-101:2016, Clause 7. In Clause 5 of this document, additional requirements are given. This document deals with various possibilities to distribute signals in a home network, using coaxial cables, balanced pair cables, fibre optic cables (glass or plastic) and also wireless links inside a room (or a small number of adjacent rooms) to replace wired cords. This document gives references to basic methods of measurement of the operational characteristics of the home cable network in order to assess its performance. All requirements refer to the performance limits, which are obtained between the input(s) at the home network interface (HNI) and the output at any system outlet when terminated in a resistance equal to the nominal load impedance of the system, unless otherwise specified. Where system outlets are not used, the above applies to the terminal input. The present document also provides limits for the accumulation of degradations if the home network is subdivided into a number of parts, using different transmission media (e.g. coaxial cabling, balanced cabling, optical cabling, wireless links). Clause 5 defines the performance limits measured at system outlet or terminal input for an unimpaired (ideal) test signal applied at the HNI. Under normal operating conditions for any digital channel and meeting these limits, the cumulative effect of the impairment of any single parameter at the HNI and that due to the home network produces signals not worse than the requirements given in IEC 60728-101-2. For digitally modulated signals, the quality requirement is a QEF (quasi error-free) reception. This document describes the physical layer connection for home networks. Description of protocols required for layer 2 and higher layers is out of the scope of this document. Logical connections between devices within the home network are therefore not always guaranteed. This International Standard is to be used in conjunction with IEC 60728-101:2016.

  • Draft
    68 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 61000-4-6:2023(Main)
Electromagnetic compatibility (EMC) - Part 4-6: Testing and measurement techniques - Immunity to conducted disturbances, induced by radio-frequency fields
SIST EN IEC 61000-4-6:2023

This part of IEC 61000 relates to the conducted immunity requirements of electrical and electronic equipment to electromagnetic disturbances coming from intended radio-frequency (RF) transmitters in the frequency range 150 kHz up to 80 MHz. NOTE 1 Product committees might decide to use the methods described in this document also for frequencies up to 230 MHz (see Annex B) although the methods and test instrumentation is intended to be used in the frequency range up to 80 MHz. Equipment not having at least one conducting wire and/or cable (such as mains supply, signal line or earth connection) which can couple the equipment to the disturbing RF fields is excluded from the scope of this publication. NOTE 2 Test methods are specified in this part of IEC 61000 to assess the effect that conducted disturbing signals, induced by electromagnetic radiation, have on the equipment concerned. The simulation and measurement of these conducted disturbances are not adequately exact for the quantitative determination of effects. The test methods specified are structured for the primary objective of establishing adequate repeatability of results at various facilities for quantitative analysis of effects. The object of this standard is to establish a common reference for evaluating the functional immunity of electrical and electronic equipment when subjected to conducted disturbances induced by RF fields. The test method documented in this part of IEC 61000 describes a consistent method to assess the immunity of an equipment or system against a specified phenomenon. NOTE 3 As described in IEC Guide 107, this standard is a basic EMC publication for use by product committees of the IEC. As also stated in Guide 107, the IEC product committees are responsible for determining whether this immunity test standard should be applied or not, and if applied, they are responsible for determining the appropriate test levels and performance criteria.

  • Standard
    86 pages
    English language
    sale 10% off
    e-Library read for
    1 day