Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-6: Tests - Tensile strength of coupling mechanism

IEC 61300-2-6:2023 is available as IEC 61300-2-6:2023 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 61300-2-6:2023 describes a test to ensure the coupling mechanism of a connector set or connector and device combination withstands the axial loads likely to be applied during normal service, and that the optical performance remains within the given specifications during this test. This third edition cancels and replaces the second edition published in 2010. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: a) addition of normative references; b) modification of the details to be specified; c) addition of optical monitoring.

Lichtwellenleiter - Verbindungselemente und passive Bauteile - Grundlegende Prüf- und Messverfahren - Teil 2-6: Prüfungen - Zugfestigkeit der Verriegelung

Dispositifs d'interconnexion et composants passifs fibroniques - Procédures fondamentales d’essais et de mesures - Partie 2-6: Essais - Résistance à la traction du mécanisme de couplage

IEC 61300-2-6:2023 est disponible sous forme de IEC 61300-2-6:2023 RLV qui contient la Norme internationale et sa version Redline, illustrant les modifications du contenu technique depuis l'édition précédente.L'IEC 61300-2-6:2023 décrit un essai destiné à vérifier que le mécanisme de couplage d'un jeu de connecteurs ou d'une combinaison d'un connecteur et d'un dispositif résiste aux charges axiales susceptibles d'être appliquées dans des conditions normales de fonctionnement et que, pendant l'essai, les performances optiques restent dans les limites spécifiées. Cette troisième édition annule et remplace la deuxième édition parue en 2010. Cette édition constitue une révision technique. Cette édition inclut les modifications techniques majeures suivantes par rapport à l'édition précédente: a) ajout de références normatives; b) modification des informations détaillées à spécifier; c) ajout du suivi optique.

Optični spojni elementi in pasivne komponente - Osnovni preskusni in merilni postopki - 2-6. del: Preskusi - Natezna trdnost spojnega mehanizma (IEC 61300-2-6:2023)

Ta del standarda IEC 61300 opisuje preskus, s katerim se zagotovi, da spojni mehanizem sklopa konektorjev ali kombinacije konektorja in naprave zdrži osne obremenitve in da optično delovanje med tem preskusom ostane znotraj določenih specifikacij.

General Information

Status
Published
Publication Date
11-Jan-2024
Current Stage
6060 - Document made available - Publishing
Start Date
12-Jan-2024
Completion Date
12-Jan-2024

Relations

Buy Standard

Standard
EN IEC 61300-2-6:2024 - BARVE
English language
13 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI STANDARD
01-marec-2024
Optični spojni elementi in pasivne komponente - Osnovni preskusni in merilni
postopki - 2-6. del: Preskusi - Natezna trdnost spojnega mehanizma (IEC 61300-2-
6:2023)
Fibre optic interconnecting devices and passive components - Basic test and
measurement procedures - Part 2-6: Tests - Tensile strength of coupling mechanism
(IEC 61300-2-6:2023)
Lichtwellenleiter - Verbindungselemente und passive Bauteile - Grundlegende Prüf- und
Messverfahren - Teil 2-6: Prüfungen - Zugfestigkeit der Verriegelung (IEC 61300-2-
6:2023)
Dispositifs d'interconnexion et composants passifs fibroniques - Procédures
fondamentales d’essais et de mesures - Partie 2-6: Essais - Résistance à la traction du
mécanisme de couplage (IEC 61300-2-6:2023)
Ta slovenski standard je istoveten z: EN IEC 61300-2-6:2024
ICS:
33.180.20 Povezovalne naprave za Fibre optic interconnecting
optična vlakna devices
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD EN IEC 61300-2-6

NORME EUROPÉENNE
EUROPÄISCHE NORM January 2024
ICS 33.180.20 Supersedes EN 61300-2-6:2011
English Version
Fibre optic interconnecting devices and passive components -
Basic test and measurement procedures - Part 2-6: Tests -
Tensile strength of coupling mechanism
(IEC 61300-2-6:2023)
Dispositifs d'interconnexion et composants passifs Lichtwellenleiter - Verbindungselemente und passive
fibroniques - Procédures fondamentales d'essais et de Bauteile - Grundlegende Prüf- und Messverfahren - Teil 2-
mesures - Partie 2-6: Essais - Résistance à la traction du 6: Prüfungen - Zugfestigkeit der Verriegelung
mécanisme de couplage (IEC 61300-2-6:2023)
(IEC 61300-2-6:2023)
This European Standard was approved by CENELEC on 2023-12-28. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Türkiye and the United Kingdom.

European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2024 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 61300-2-6:2024 E

European foreword
The text of document 86B/4808/FDIS, future edition 3 of IEC 61300-2-6, prepared by SC 86B "Fibre
optic interconnecting devices and passive components" of IEC/TC 86 "Fibre optics" was submitted to
the IEC-CENELEC parallel vote and approved by CENELEC as EN IEC 61300-2-6:2024.
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2024-09-28
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2024-12-28
document have to be withdrawn
This document supersedes EN 61300-2-6:2011 and all of its amendments and corrigenda (if any).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
Any feedback and questions on this document should be directed to the users’ national committee. A
complete listing of these bodies can be found on the CENELEC website.
Endorsement notice
The text of the International Standard IEC 61300-2-6:2023 was approved by CENELEC as a
European Standard without any modification.
In the official version, for Bibliography, the following note has to be added for the standard indicated:
IEC 61753-1 NOTE Approved as EN IEC 61753-1
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1 Where an International Publication has been modified by common modifications, indicated by (mod), the
relevant EN/HD applies.
NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available
here: www.cencenelec.eu.
Publication Year Title EN/HD Year
IEC 61300-1 - Fibre optic interconnecting devices and EN IEC 61300-1 -
passive components - Basic test and
measurement procedures - Part 1: General
and guidance
IEC 61300-3-1 - Fibre optic interconnecting devices and EN 61300-3-1 -
passive components - Basic test and
measurement procedures - Part 3-1:
Examinations and measurements - Visual
examination
IEC 61300-3-3 - Fibre optic interconnecting devices and EN 61300-3-3 -
passive components - Basic test and
measurement procedures - Part 3-3:
Examinations and measurements - Active
monitoring of changes in attenuation and
return loss
IEC 61300-2-6 ®
Edition 3.0 2023-11
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
colour
inside
Fibre optic interconnecting devices and passive components – Basic test and

measurement procedures –
Part 2-6: Tests – Tensile strength of coupling mechanism

Dispositifs d'interconnexion et composants passifs fibroniques – Procédures

fondamentales d’essais et de mesures –

Partie 2-6: Essais – Résistance à la traction du mécanisme de couplage

INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 33.180.20  ISBN 978-2-8322-7875-8

– 2 – IEC 61300-2-6:2023 © IEC 2023
CONTENTS
FOREWORD . 3
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 5
4 Apparatus . 5
4.1 General . 5
4.2 Force generator . 6
4.3 Force gauge . 7
4.4 Clamping device . 7
4.5 DUT mount . 7
5 Procedure . 7
5.1 General . 7
5.2 Preconditioning . 7
5.3 Prepare DUT . 7
5.4 Initial visual examinations and measurements . 7
5.5 Mount DUT . 7
5.6 Apply load . 8
5.7 Recovery . 8
5.8 Final examination and measurements . 8
6 Severity . 8
7 Details to be specified and reported. 9
Bibliography . 10

Figure 1 – Example of test apparatus . 6

Table 1 – Recommended severity values . 8

IEC 61300-2-6:2023 © IEC 2023 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
FIBRE OPTIC INTERCONNECTING
DEVICES AND PASSIVE COMPONENTS –
BASIC TEST AND MEASUREMENT PROCEDURES –

Part 2-6: Tests – Tensile strength of coupling mechanism

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international
co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and
in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports,
Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their
preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with
may participate in this preparatory work. International, governmental and non-governmental organizations liaising
with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for
Standardization (ISO) in accordance with conditions determined by agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence between
any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) IEC draws attention to the possibility that the implementation of this document may involve the use of (a)
patent(s). IEC takes no position concerning the evidence, validity or applicability of any claimed patent rights in
respect thereof. As of the date of publication of this document, IEC had not received notice of (a) patent(s), which
may be required to implement this document. However, implementers are cautioned that this may not represent
the latest information, which may be obtained from the patent database available at https://patents.iec.ch. IEC
shall not be held responsible for identifying any or all such patent rights.
IEC 61300-2-6 has been prepared by subcommittee 86B: Fibr
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.