EN 61326-2-5:2013

Electrical equipment for measurement, control and laboratory use - EMC requirements - Part 2-5: Particular requirements - Test configurations, operational conditions and performance criteria for devices with field bus interfaces according to IEC 61784-1

IEC 61326-2-5:2012 treats the particular features for EMC testing of field devices with field bus interfaces. This part of IEC 61326 covers only the field bus interface of the equipment. This second edition cancels and replaces the first edition published in 2005. This edition constitutes a technical revision. The main technical changes are: Update with respect to IEC 61326-1:2012.

Elektrische Mess-, Steuer-, Regel- und Laborgeräte – EMV-Anforderungen – Teil 2-5: Besondere Anforderungen – Prüfanordnungen, Betriebsbedingungen und Leistungsmerkmale für Feldgeräte mit Feldbus-Schnittstellen gemäß IEC 61784-1

Matériel électrique de mesure, de commande et de laboratoire - Exigences relatives à la CEM - Partie 2-5: Exigences particulières - Configurations d'essai, conditions de fonctionnement et critères d'aptitude à la fonction pour les équipements de terrain avec des interfaces utilisant des bus de terrain conformes à la CEI 61784-1

La CEI 61326-2-5:2012 traite des caractéristiques particulières pour les essais de CEM des équipements de terrain avec des interfaces utilisant des bus de terrain. La présente partie de la CEI 61326 couvre uniquement l'interface utilisant le bus de terrain du matériel. Cette deuxième édition annule et remplace la première édition parue en 2005. Cette édition constitue une révision technique. Les principaux changements techniques sont: Mise à jour par rapport à la CEI 61326-1:2012.

Električna oprema za merjenje, kontrolo in laboratorijsko uporabo - Zahteve za elektromagnetno združljivost (EMC) - 2-5. del: Posebne zahteve - Preskusne konfiguracije, obratovalni pogoji in merila za lastnosti terenskih naprav z vmesnikom po IEC 61784-1 (IEC 61326-2-5:2012)

Poleg zahtev mednarodnega standarda IEC 61326-1 ta del standarda IEC 61326 obravnava posebne lastnosti za preskušanje elektromagnetne združljivosti terenskih naprav z vmesnikom. Ta del standarda IEC 61326 zajema le vmesnik opreme. OPOMBA Druge funkcije opreme še naprej opisujejo drugi deli skupine standardov IEC 61326. Ta del se nanaša samo na terenske naprave, namenjene uporabi pri kontroli procesov in merjenju procesov. V tem standardu so zajete terenske naprave z vmesniki po IEC 61784-1, CP 3/2 in CP 1/1, kot je opredeljeno v standardu IEC 61784. Druga procesna vodila bodo morda vključena v prihodnje izdaje tega standarda. Standard IEC 61784-1 določa sklop komunikacijskih profilov, specifičnih za protokol, na podlagi standarda IEC 61158. Proizvajalec določi okolje, v katerem naj bi se izdelek uporabljal, in/ali izbere ustrezne specifikacije preskusne ravni iz standarda IEC 61326-1.

General Information

• Status: Withdrawn
• Publication Date: 10-Jan-2013
• Withdrawal Date: 05-Nov-2015
• ICS: 17.220 - Electricity. Magnetism. Electrical and magnetic measurements
• ICS: 25.040.40 - Industrial process measurement and control
• ICS: 33.100 - Electromagnetic compatibility (EMC)
• Technical Committee: CLC/TC 65X - Industrial-process measurement, control and automation
• Drafting Committee: IEC/SC 65A - IEC_SC_65A
• Current Stage: 9960 - Withdrawal effective - Withdrawal
• Start Date: 04-Jun-2024
• Completion Date: 04-Jun-2024
• Directive: 2004/108/EC - Directive 2004/108/EC of the European Parliament and of the Council of 15 December 2004 on the approximation of the laws of the Member States relating to electromagnetic compatibility and repealing Directive 89/336/EEC
• Directive: 2004/108/EU - DIRECTIVE 2004/108/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL of 15 December 2004 on the approximation of the laws of the Member States relating to electromagnetic compatibility and repealing Directive 89/336/EEC
• Directive: 2014/30/EU - Directive 2014/30/EU of the European Parliament and of the Council of 26 February 2014 on the harmonisation of the laws of the Member States relating to electromagnetic compatibility (recast)
• Ref Project: SIST EN 61326-2-5:2013 - Electrical equipment for measurement, control and laboratory use - EMC requirements - Part 2-5: Particular requirements - Test configurations, operational conditions and performance criteria for devices with field bus interfaces according to IEC 61784-1 (IEC 61326-2-5:2012)

Relations

• Replaces: EN 61326-2-5:2006 - Electrical equipment for measurement, control and laboratory use - EMC requirements - Part 2-5: Particular requirements - Test configurations, operational conditions and performance criteria for field devices with interfaces according to IEC 61784-1, CP 3/2
• Effective Date: 28-Jan-2023
• Replaced By: EN IEC 61326-2-5:2021 - Electrical equipment for measurement, control and laboratory use - EMC requirements - Part 2-5: Particular requirements - Test configurations, operational conditions and performance criteria for field devices with field bus interfaces according to IEC 61784-1
• Effective Date: 08-Jun-2021

Standards Content (Sample)

SLOVENSKI STANDARD
01-marec-2013
1DGRPHãþD
SIST EN 61326-2-5:2007
(OHNWULþQDRSUHPD]DPHUMHQMHNRQWURORLQODERUDWRULMVNRXSRUDER=DKWHYH]D
HOHNWURPDJQHWQR]GUXåOMLYRVW(0&GHO3RVHEQH]DKWHYH3UHVNXVQH
NRQILJXUDFLMHREUDWRYDOQLSRJRMLLQPHULOD]DODVWQRVWLWHUHQVNLKQDSUDY]
YPHVQLNRPSR,(&,(&
Electrical equipment for measurement, control and laboratory use - EMC requirements -
Part 2-5: Particular requirements - Test configurations, operational conditions and
performance criteria for devices with field bus interfaces according to IEC 61784-1 (IEC
61326-2-5:2012)
Elektrische Mess-, Steuer-, Regel- und Laborgeräte - EMV-Anforderungen - Teil 2-5:
Besondere Anforderungen - Prüfanordnungen, Betriebsbedingungen und
Leistungsmerkmale für Geräte mit Feldbus-Schnittstellen gemäß IEC 61784-1 (IEC
61326-2-5:2012)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

Matériel électrique de mesure, de commande et de laboratoire - Exigences relatives à la
CEM - Partie 2-4: Exigences particulières - Configurations d'essai, conditions de
fonctionnement et critères d'aptitude à la fonction pour les appareils en exploitation avec
des interfaces utilisant des bus de terrain conformes à la CEI 61784-1 (CEI 61326-2-
5:2012)
Ta slovenski standard je istoveten z: EN 61326-2-5:2013
ICS:
19.080 (OHNWULþQRLQHOHNWURQVNR Electrical and electronic
SUHVNXãDQMH testing
33.100.01 Elektromagnetna združljivost Electromagnetic compatibility
na splošno in general
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN 61326-2-5
NORME EUROPÉENNE
January 2013
EUROPÄISCHE NORM
ICS 17.220; 25.040.40; 33.100 Supersedes EN 61326-2-5:2006

English version
Electrical equipment for measurement, control and laboratory use -
EMC requirements -
Part 2-5: Particular requirements -
Test configurations, operational conditions and performance criteria for
devices with field bus interfaces according to IEC 61784-1
(IEC 61326-2-5:2012)
Matériel électrique de mesure, de Elektrische Mess-, Steuer-, Regel- und
commande et de laboratoire - Laborgeräte – EMV-Anforderungen – Teil
Exigences relatives à la CEM - 2-5: Besondere Anforderungen –
Partie 2-4: Exigences particulières - Prüfanordnungen, Betriebsbedingungen
Configurations d'essai, conditions de und Leistungsmerkmale für Feldgeräte mit
fonctionnement et critères d'aptitude à la Feldbus-Schnittstellen gemäß IEC 61784-
fonction pour les appareils en exploitation 1
avec des interfaces utilisant des bus de (IEC 61326-2-5:2012)
terrain conformes à la CEI 61784-1
(CEI 61326-2-5:2012)
This European Standard was approved by CENELEC on 2012-11-06. CENELEC members are bound to comply
with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard
the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the CEN-CENELEC Management Centre or to any CENELEC member.

This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and notified
to the CEN-CENELEC Management Centre has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus,
the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany,
Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.

CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung

Management Centre: Avenue Marnix 17, B - 1000 Brussels

© 2013 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 61326-2-5:2013 E
Foreword
The text of document 65A/643/FDIS, future edition 2 of IEC 61326-2-5, prepared by SC 65A, "System
aspects", of IEC TC 65, "Industrial-process measurement, control and automation" was submitted to the
IEC-CENELEC parallel vote and approved by CENELEC as EN 61326-2-5:2013.

The following dates are fixed:
• latest date by which the document has (dop) 2013-08-06
to be implemented at national level by
publication of an identical national
standard or by endorsement
(dow) 2015-11-06
• latest date by which the national
standards conflicting with the
document have to be withdrawn
This document supersedes EN 61326-2-5:2006.
5:2006:
– Update with respect to EN 61326-1:2013.
of clauses, subclauses, tables and figures.
When a particular subclause of EN 61326-1 is not mentioned in this part, that subclause applies as far as
is reasonable. When this standard states “addition”, “modification” or “replacement”, the relevant text in
EN 61326-1 is to be adapted accordingly.
NOTE The following numbering system is used:
– subclauses, tables and figures that are numbered starting from 101 are additional to those in EN 61326-1;
– unless notes are in a new subclause or involve notes in EN 61326-1, they are numbered starting from 101 including
those in a replaced clause or subclause;
– additional annexes are lettered AA, BB, etc.

Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such patent
rights.
This document has been prepared under a mandate given to CENELEC by the European Commission
and the European Free Trade Association, and supports essential requirements of EU Directive(s).

For the relationship with EU Directive(s) see informative Annex ZZ, which is an integral part of this
document.
Endorsement notice
The text of the International Standard IEC 61326-2-5:2012 was approved by CENELEC as a European
Standard without any modification.

- 3 - EN 61326-2-5:2013
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications

The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.

NOTE  When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD
applies.
Annex ZA of EN 61326-1:2013 applies, except as follows:

Publication Year Title EN/HD Year

Addition:
IEC 61158-2 2010 Industrial communication networks - Fieldbus EN 61158-2 2010
specifications -
Part 2: Physical layer specification and service
definition
IEC 61158-3-3 2007 Industrial communication networks - Fieldbus EN 61158-3-3 2008
specifications -
Part 3-3: Data-link layer service definition -
Type 3 elements
IEC 61158-5-5 2007 Industrial communication networks - Fieldbus EN 61158-5-5 2008
specifications -
Part 5-5: Application layer service definition -
Type 5 elements
IEC 61158-6-10 2010 Industrial communication networks - Fieldbus EN 61158-6-10 2012
specifications -
Part 6-10: Application layer protocol
specification - Type 10 elements

IEC 61784-1 2010 Industrial communication networks - Profiles - EN 61784-1 2010
Part 1: Fieldbus profiles
Annex ZZ
(informative)
Coverage of Essential Requirements of EU Directives
This European Standard has been prepared under a mandate given to CENELEC by the European
Commission and the European Free Trade Association and within its scope the standard covers
protection requirements of Annex I, Article 1 of the EC Directive 2004/108/EC.
Compliance with this standard provides one means of conformity with the specified essential
requirements of the Directive[s] concerned.
NOTE Other requirements and other EU Directives may be applicable to the products falling within the scope of
this standard.
IEC 61326-2-5 ®
Edition 2.0 2012-10
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Electrical equipment for measurement, control and laboratory use – EMC

requirements –
Part 2-5: Particular requirements – Test configurations, operational conditions

and performance criteria for field devices with field bus interfaces according to

IEC 61784-1
Matériel électrique de mesure, de commande et de laboratoire – Exigences

relatives à la CEM –
Partie 2-5: Exigences particulières – Configurations d'essai, conditions de

fonctionnement et critères d’aptitude à la fonction pour les équipements de

terrain avec des interfaces utilisant des bus de terrain conformes à la

CEI 61784-1
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
PRICE CODE
INTERNATIONALE
CODE PRIX Q
ICS 17.220; 25.040.40; 33.100 ISBN 978-2-83220-396-5

– 2 – 61326-2-5 © IEC:2012
CONTENTS
FOREWORD . 3
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 6
4 General . 6
5 EMC test plan . 6
5.1 General . 6
5.2 Configuration of EUT during testing . 6
5.3 Operation conditions of EUT during testing . 6
5.4 Specification of functional performance . 6
5.5 Test description . 6
6 Immunity requirements . 6
6.1 Conditions during the tests . 6
6.2 Immunity test requirements . 6
6.3 Random aspects. 6
6.4 Performance criteria . 7
7 Emission requirements . 7
8 Test results and test report . 7
9 Instructions for use . 7
Annex AA (normative) Particular requirements – Test configurations, operational
conditions and performance criteria for field devices with field bus interfaces according
to IEC 61784-1 CP 1/1 . 8
Annex BB (normative) Particular requirements – Test configurations, operational
conditions and performance criteria for field devices with field bus interfaces according
to IEC 61784-1 CP 3/2 . 13

Figure AA.1 – Test set up for EUT with CP 1/1 interface . 10
Figure BB.1 – Test set up for EUT with CP 3/2 interface . 15

61326-2-5 © IEC:2012 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
ELECTRICAL EQUIPMENT FOR MEASUREMENT,
CONTROL AND LABORATORY USE –
EMC REQUIREMENTS –
Part 2-5: Particular requirements –
Test configurations, operational conditions and performance criteria
for field devices with field bus interfaces according to IEC 61784-1

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Repor
...