EN IEC 60286-2:2022
(Main)Packaging of components for automatic handling - Part 2: Tape packaging of components with unidirectional leads on continuous tapes
Packaging of components for automatic handling - Part 2: Tape packaging of components with unidirectional leads on continuous tapes
IEC 60286-2:2022 applies to the tape packaging of components with two or more unidirectional leads for use in electronic equipment. It provides dimensions and tolerances necessary to tape components with unidirectional leads. In general, the tape is applied to the component leads. It covers requirements for taping techniques used with equipment for automatic handling, pre-forming of leads, insertion and other operations and includes only those dimensions which are essential to the taping of components intended for the above-mentioned purposes. This edition includes the following significant technical changes with respect to the previous edition: a) complete revision of structure; b) consolidation of essential parameters and requirements in Clause 4.
Gurtung und Magazinierung von Bauelementen für automatische Verarbeitung – Teil 2: Gurtung von Bauelementen mit einseitig herausgeführten Anschlussdrähten
Emballage de composants pour opérations automatisées - Partie 2: Emballage des composants à sorties unilatérales en bandes continues
L’IEC 60286-2:2022 s’applique à l’emballage des composants à deux sorties unilatérales ou plus utilisés dans les équipements électroniques. Elle fournit les dimensions et tolérances nécessaires pour la mise sur bande des composants à sorties unilatérales. En général, la bande est appliquée aux sorties des composants. Elle spécifie les exigences relatives aux techniques de mise sur bande utilisées avec les équipements pour les opérations automatisées, le préformage des sorties, l’insertion et d’autres opérations automatiques. Elle fournit uniquement les dimensions essentielles pour la mise sur bande de composants destinés aux opérations mentionnées ci-dessus. Cette édition inclut les modifications techniques majeures suivantes par rapport à l’édition précédente:
révision complète de la structure;
consolidation des exigences et paramètres essentiels à l’Article 4.
Pakiranje komponent za samodejno obdelavo - 2. del: Trakanje komponent z enostranskimi izvodi na neprekinjene trakove (IEC 60286-2:2022)
Standard IEC 60286-2:2022 se uporablja za tračno pakiranje komponent z dvema ali več enostranskimi izvodi za uporabo v elektronski opremi. Določa dimenzije in tolerance, potrebne za trakanje komponent z enostranskimi izvodi. V splošnem se trak nanese na priključke komponent.
Standard zajema zahteve za tehnike trakanja, ki se uporabljajo z opremo za samodejno obdelavo, predobdelavo izvodov, vstavljanje in druge operacije, ter vključuje samo tiste dimenzije, ki so bistvene za trakanje komponent, ki se uporabljajo za zgoraj omenjene namene.
Ta izdaja v primerjavi s prejšnjo vključuje naslednje pomembne tehnične spremembe:
a) popolna revizija strukture;
b) konsolidacija bistvenih parametrov in zahtev iz točke 4.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-marec-2023
Nadomešča:
SIST EN 60286-2:2015
Pakiranje komponent za samodejno obdelavo - 2. del: Trakanje komponent z
enostranskimi izvodi na neprekinjene trakove (IEC 60286-2:2022)
Packaging of components for automatic handling - Part 2: Tape packaging of
components with unidirectional leads on continuous tapes (IEC 60286-2:2022)
Gurtung und Magazinierung von Bauelementen für automatische Verarbeitung – Teil 2:
Gurtung von Bauelementen mit einseitig herausgeführten Anschlussdrähten (IEC 60286-
2:2022)
Emballage de composants pour opérations automatisées - Partie 2: Emballage des
composants à sorties unilatérales en bandes continues (IEC 60286-2:2022)
Ta slovenski standard je istoveten z: EN IEC 60286-2:2022
ICS:
31.020 Elektronske komponente na Electronic components in
splošno general
55.020 Pakiranje in distribucija blaga Packaging and distribution of
na splošno goods in general
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD EN IEC 60286-2
NORME EUROPÉENNE
EUROPÄISCHE NORM December 2022
ICS 31.020; 31.240 Supersedes EN 60286-2:2015
English Version
Packaging of components for automatic handling - Part 2: Tape
packaging of components with unidirectional leads on
continuous tapes
(IEC 60286-2:2022)
Emballage de composants pour opérations automatisées - Gurtung und Magazinierung von Bauelementen für
Partie 2: Emballage des composants à sorties unilatérales automatische Verarbeitung - Teil 2: Gurtung von
en bandes continues Bauelementen mit einseitig herausgeführten
(IEC 60286-2:2022) Anschlussdrähten
(IEC 60286-2:2022)
This European Standard was approved by CENELEC on 2022-12-20. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Türkiye and the United Kingdom.
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2022 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 60286-2:2022 E
European foreword
The text of document 40/2974/FDIS, future edition 5 of IEC 60286-2, prepared by IEC/TC 40
"Capacitors and resistors for electronic equipment" was submitted to the IEC-CENELEC parallel vote
and approved by CENELEC as EN IEC 60286-2:2022.
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2023-09-20
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2025-12-20
document have to be withdrawn
This document supersedes EN 60286-2:2015 and all of its amendments and corrigenda (if any).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
Any feedback and questions on this document should be directed to the users’ national committee. A
complete listing of these bodies can be found on the CENELEC website.
Endorsement notice
The text of the International Standard IEC 60286-2:2022 was approved by CENELEC as a European
Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standard indicated:
IEC 60301 NOTE Harmonized as EN 60301
IEC 60717 NOTE Harmonized as EN 60717
ISO 11468 NOTE Harmonized as EN ISO 11468
IEC 60286-2 ®
Edition 5.0 2022-11
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Packaging of components for automatic handling –
Part 2: Tape packaging of components with unidirectional leads on continuous
tapes
Emballage de composants pour opérations automatisées –
Partie 2: Emballage des composants à sorties unilatérales en bandes continues
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 31.020; 31.240 ISBN 978-2-8322-6029-6
– 2 – IEC 60286-2:2022 © IEC 2022
CONTENTS
FOREWORD . 4
1 Scope . 6
2 Normative references . 6
3 Terms and definitions . 6
4 Dimensions and specific requirements . 7
4.1 General . 7
4.2 Coordinate system . 7
4.3 Lead taping dimensions . 8
4.4 Specific requirements to components and sprocket hole pitches (P, P , P ,
0 1
P , D ) . 11
2 0
4.5 Specific requirements to leads . 12
4.5.1 General . 12
4.5.2 Lead diameter (d, d ) . 12
4.5.3 Lead spacing (F, F , F ) . 12
1 2
4.6 Specific requirements to component position in taping (∆h, ∆p, ∆P ) . 12
4.7 Specific requirements to components with unguided leads . 12
4.7.1 Distance between the abscissa and tip of unguided lead (H ) . 12
4.7.2 Distance between the bottom of the component and the tip of the
unguided lead (H ) . 13
4.7.3 Distance between the lead terminal and the unguided lead (K) . 13
5 Requirements to taping . 13
5.1 Taping dimensions . 13
5.2 Polarity and orientation requirements of components on tape . 13
5.3 Adhesion to tape and extraction force for components . 14
5.4 Splices . 14
5.5 Tape leader and trailer . 14
6 Requirements to tape material . 15
6.1 Tape breaking force . 15
6.2 Tape material . 15
6.3 Hold-down tape . 15
7 Packing . 16
7.1 General . 16
7.2 Reel dimensions . 16
7.2.1 General . 16
7.2.2 Component tape reeling . 17
7.2.3 Component protection. 17
7.2.4 Reel filling . 17
7.3 Maximum dimensions of the fan-fold container . 17
7.4 Missing components . 18
7.5 Marking . 20
8 Recycling. 20
Annex A (normative) Dimensions for two leads . 21
A.1 Dimensions for two formed leads, sprocket hole between parts . 21
A.2 Dimensions for two formed leads, sprocket hole between leads . 23
A.3 Dimensions for two straight leads, sprocket hole between parts . 25
IEC 60286-2:2022 © IEC 2022 – 3 –
A.4 Dimensions for two straight leads, sprocket hole between leads . 27
Annex B (normative) Dimensions for three leads . 30
B.1 Dimensions for three formed leads, sprocket hole between parts . 30
B.2 Dimensions for three formed leads, sprocket hole between leads . 32
Bibliography . 35
Figure 1 – Abscissa, ordinate, reference plane and seating plane . 8
Figure 2 – Crimped or otherwise formed leads . 8
Figure 3 – Lead taping dimensions (straight leads) . 8
Figure 4 – Lead taping dimensions (crimped leads) . 9
Figure 5 – Lead taping dimensions – unguided leads . 9
Figure 6 – Front-to-back and lateral deviations . 10
Figure 7 – Position of short terminal without tape . 13
Figure 8 – Pull strength (extraction from taping) . 14
Figure 9 – Leader and trailer of tape . 15
Figure 10 – Symbols for reel dimensions . 16
Figure 11 – Reeling . 17
Figure 12 – Symbols for fan-fold container dimensions . 18
Figure 13 – Missing components . 19
Figure A.1 – Symbol references for two formed leads, sprocket hole between parts . 22
Figure A.2 – Symbol references for two formed leads, sprocket hole between leads . 24
Figure A.3 – Symbol references for two straight leads, sprocket hole between parts . 26
Figure A.4 – Symbol references for two straight leads, sprocket hole between leads . 28
Figure B.1 – Symbol references for three formed leads, sprocket hole between parts . 31
Figure B.2 – Symbol references for three formed leads, sprocket hole between leads . 33
Table 1 – Lead taping dimensions . 10
Table 2 – Reel dimensions . 16
Table 3 – Maximum outer dimensions for a fan-fold container . 18
Table A.1 – Dimensions for two formed leads, sprocket hole between parts . 23
Table A.2 – Dimensions for two formed leads, sprocket hole between leads . 25
Table A.3 – Dimensions for two straight leads, sprocket hole between parts . 27
Table A.4 –
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.