EN IEC 61169-1-5:2022
(Main)Radio frequency connectors - Part 1-5: Electrical test methods - Rise time degradation
Radio frequency connectors - Part 1-5: Electrical test methods - Rise time degradation
IEC 61169-1-5:2022 provides test methods for the rise time degradation of radio frequency (RF) connector. This document is applicable to triaxial and other radio frequency connectors.
Hochfrequenz-Steckverbinder – Teil 1-5: Elektrische Prüfverfahren - Degradation der Anstiegszeit
Connecteurs pour fréquences radioélectriques - Partie 1-5: Méthodes d’essai électrique - Dégradation du temps de montée
IEC 61169-1-5:2022 fournit des méthodes d’essai pour la dégradation du temps de montée d’un connecteur pour fréquences radioélectriques (RF, radio frequency). Le présent document s’applique aux connecteurs triaxiaux et autres connecteurs pour fréquences radioélectriques.
Radiofrekvenčni konektorji - 1-5. del: Električne preskusne metode - Poslabšanje časa vzpona (IEC 61169-1-5:2022)
Ta del standarda IEC 61169 zagotavlja preskusne metode za poslabšanje časa vzpona radiofrekvenčnega (RF) konektorja. Ta dokument se uporablja za triaksialne in druge radiofrekvenčne konektorje.
General Information
Standards Content (Sample)
SLOVENSKI STANDARD
01-junij-2022
Radiofrekvenčni konektorji - 1-5. del: Električne preskusne metode - Poslabšanje
časa vzpona (IEC 61169-1-5:2022)
Radio frequency connectors - Part 1-5: Electrical test methods - Rise time degradation
(IEC 61169-1-5:2022)
Hochfrequenz-Steckverbinder - Teil 1-5: Elektrische Prüfverfahren - Degradation der
Anstiegszeit (IEC 61169-1-5:2022)
Connecteurs pour fréquences radioélectriques - Partie 1-5: Méthodes d’essai électrique -
Dégradation du temps de montée (IEC 61169-1-5:2022)
Ta slovenski standard je istoveten z: EN IEC 61169-1-5:2022
ICS:
33.120.30 Radiofrekvenčni konektorji RF connectors
(RF)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD EN IEC 61169-1-5
NORME EUROPÉENNE
EUROPÄISCHE NORM March 2022
ICS 33.120.10
English Version
Radio frequency connectors - Part 1-5: Electrical test methods -
Rise time degradation
(IEC 61169-1-5:2022)
Connecteurs pour fréquences radioélectriques - Partie 1-5: Hochfrequenz-Steckverbinder - Teil 1-5: Elektrische
Méthodes d'essai électrique - Dégradation du temps de Prüfverfahren - Degradation der Anstiegszeit
montée (IEC 61169-1-5:2022)
(IEC 61169-1-5:2022)
This European Standard was approved by CENELEC on 2022-03-10. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2022 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 61169-1-5:2022 E
European foreword
The text of document 46F/592/FDIS, future edition 1 of IEC 61169-1-5, prepared by SC 46F "RF and
microwave passive components" of IEC/TC 46 "Cables, wires, waveguides, RF connectors, RF and
microwave passive components and accessories" was submitted to the IEC-CENELEC parallel vote
and approved by CENELEC as EN IEC 61169-1-5:2022.
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2022-12-10
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2025-03-10
document have to be withdrawn
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
Any feedback and questions on this document should be directed to the users’ national committee. A
complete listing of these bodies can be found on the CENELEC website.
Endorsement notice
The text of the International Standard IEC 61169-1-5:2022 was approved by CENELEC as a
European Standard without any modification.
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1 Where an International Publication has been modified by common modifications, indicated by (mod), the
relevant EN/HD applies.
NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available
here: www.cenelec.eu.
Publication Year Title EN/HD Year
IEC 61169-1 - Radio frequency connectors - Part 1: EN 61169-1 -
Generic specification - General
requirements and measuring methods
IEC 61169-1-5 ®
Edition 1.0 2022-02
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
colour
inside
Radio frequency connectors –
Part 1-5: Electrical test methods – Rise time degradation
Connecteurs pour fréquences radioélectriques –
Partie 1-5: Méthodes d’essai électrique – Dégradation du temps de montée
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 33.120.10 ISBN 978-2-8322-1074-1
– 2 – IEC 61169-1-5:2022 © IEC 2022
CONTENTS
FOREWORD . 3
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 5
4 Test principle . 6
5 Measurement system . 7
5.1 General . 7
5.2 Equipment . 8
6 Preparation of test sample . 8
6.1 Insertion method . 8
6.2 Reference method . 8
7 Test procedure . 9
7.1 General . 9
7.2 Insertion method . 9
7.3 Reference method . 10
7.4 Calculation of test data . 11
8 Failure criterion . 11
9 Information to be given in the relevant specification . 11
10 Test report . 12
Figure 1 – The equivalent distribution parameter of the sample under test . 6
Figure 2 – Test principle . 7
Figure 3 – Preparation of cable RF connector test sample (insertion method) . 8
Figure 4 – Preparation of cable RF connector test sample (reference method) . 9
Figure 5 – Insertion method . 10
Figure 6 – Reference method . 11
Table 1 – Measurement system rise time . 7
IEC 61169-1-5:2022 © IEC 2022 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
RADIO FREQUENCY CONNECTORS –
Part 1-5: Electrical test methods – Rise time degradation
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international
co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and
in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports,
Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their
preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with
may participate in this preparatory work. International, governmental and non-governmental organizations liaising
with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for
Standardization (ISO) in accordance with conditions determined by agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence between
any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent
rights. IEC shall not be held responsible for identifying any or all such patent rights.
IEC 61169-1-5 has been prepared by subcommittee 46F: RF and microwave passive
components, of IEC technical committee 46: Cables, wires, waveguides, RF connectors, RF
and microwave passive components and accessories. It is an International Standard.
The text of this International Standard is based on the following documents:
Draft Report on voting
46F/592/FDIS 46F/608/RVD
Full information on the voting for its approval can be found in the report on voting indicated in
the above table.
The language used for the development of this International Standard is English.
– 4 – IEC 61169-1-5:2022 © IEC 2022
This document was drafted in accordance with ISO/IEC Directives, Part 2, and developed in
accordance with ISO/IEC Directives, Part 1 and ISO/IEC Directives, IEC Supplement, available
at www.iec.ch/members_experts/refdocs. The main document types developed by IEC are
described in greater detail at www.iec.ch/standardsdev/publications.
A list of all parts of the IEC 61169 series, under the general title Radio frequency connectors
can be found on the IEC website.
The committee has decided that the contents of this document will remain unchanged until the
stability date indicated on the IEC website under webstore.iec.ch in the data related to the
specific document. At this date, the document will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
IMPORTANT – The "colour inside" logo on the cover page of this document indicates that it
contains colours which are considered to be useful for the correct unders
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.