EN IEC 60317-70-1:2020
(Main)Specifications for particular types of winding wires - Part 70-1: Polyester glass-fibre wound unvarnished and fused, bare or enamelled round copper wire, temperature index 155
Specifications for particular types of winding wires - Part 70-1: Polyester glass-fibre wound unvarnished and fused, bare or enamelled round copper wire, temperature index 155
IEC 60317-70-1:2020 specifies the requirements of polyester glass-fibre wound unvarnished and fused bare, grade 1 or grade 2 enamelled round copper winding wires, temperature index 155. The nominal conductor diameters are specified in Clause 4 of IEC 60317-0-10:2017. NOTE For this type of wire, the heat shock test is inappropriate and therefore a heat shock temperature cannot be established. Consequently, a class based on the requirements for temperature index and heat shock temperature cannot be specified.
Technische Lieferbedingungen für bestimmte Typen von Wickeldrähten - Teil 70-1: Runddrähte aus Kupfer, blank oder lackisoliert, mit Polyester-Glas-Fasergewebe umsponnen und verschmolzen und nicht imprägniert, Temperaturindex 155
Spécifications pour types particuliers de fils de bobinage - Partie 70-1: Fil de section circulaire en cuivre nu ou émaillé, guipé de fibres de verre polyester fondues non vernies, d'indice de température 155
IEC 60317-70-1:2020 spécifie les exigences relatives aux fils de bobinage de section circulaire en cuivre nus ou émaillés de grade 1 ou de grade 2, guipés de fibres de verre polyester fondues non vernies, d'indice de température 155. Les diamètres nominaux des conducteurs sont spécifiés à l'Article 4 de l'IEC 60317-0-10:2017. NOTE Pour ce type de fil, l'essai de choc thermique ne s'applique pas et la température de choc thermique ne peut donc pas être définie. Par conséquent, une classe fondée sur les exigences d'indice de température et de température de choc thermique ne peut pas être spécifiée.
Specifikacije za posebne vrste navijalnih žic - 70-1. del: S poliestrskim steklenim vlaknom povita, impregnirana s silikonsko smolo ali lakom, gola ali emajlirana pravokotna bakrena žica, temperaturni indeks 155 (IEC 60317-70-1:2020)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-oktober-2020
Nadomešča:
SIST EN 60317-70:2017
Specifikacije za posebne vrste navijalnih žic - 70-1. del: S poliestrskim steklenim
vlaknom povita, impregnirana s silikonsko smolo ali lakom, gola ali emajlirana
pravokotna bakrena žica, temperaturni indeks 155 (IEC 60317-70-1:2020)
Specifications for particular types of winding wires - Part 70-1: Polyester glass-fibre
wound unvarnished and fused, bare or enamelled round copper wire, temperature index
155 (IEC 60317-70-1:2020)
Technische Lieferbedingungen für bestimmte Typen von Wickeldrähten - Teil 70-1:
Runddrähte aus Kupfer, blank oder lackisoliert, mit Polyesterglasfasern umsponnen und
verschmolzen und nicht imprägniert, Temperaturindex 155 (IEC 60317-70-1:2020)
Spécifications pour types particuliers de fils de bobinage - Partie 70-1: Fil de section
circulaire en cuivre nu ou émaillé, guipé de fibres de verre polyester fondues non
vernies, d'indice de température 155 (IEC 60317-70-1:2020)
Ta slovenski standard je istoveten z: EN IEC 60317-70-1:2020
ICS:
29.060.10 Žice Wires
77.150.30 Bakreni izdelki Copper products
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD EN IEC 60317-70-1
NORME EUROPÉENNE
EUROPÄISCHE NORM
August 2020
ICS 29.060.10 Supersedes EN 60317-70:2017 (partially)
and all of its amendments and corrigenda (if any)
English Version
Specifications for particular types of winding wires - Part 70-1:
Polyester glass-fibre wound unvarnished and fused, bare or
enamelled round copper wire, temperature index 155
(IEC 60317-70-1:2020)
Spécifications pour types particuliers de fils de bobinage - Technische Lieferbedingungen für bestimmte Typen von
Partie 70-1: Fil de section circulaire en cuivre nu ou émaillé, Wickeldrähten - Teil 70-1: Runddrähte aus Kupfer, blank
guipé de fibres de verre polyester fondues non vernies, oder lackisoliert, mit Polyesterglasfasern umsponnen und
d'indice de température 155 verschmolzen und nicht imprägniert, Temperaturindex 155
(IEC 60317-70-1:2020) (IEC 60317-70-1:2020)
This European Standard was approved by CENELEC on 2020-07-27. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2020 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 60317-70-1:2020 E
European foreword
The text of document 55/1845/FDIS, future edition 1 of IEC 60317-70-1, prepared by IEC/TC 55
"Winding wires" was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2021-04-27
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2023-07-27
document have to be withdrawn
This document supersedes (partially) EN 60317-70:2017 and all of its amendments and corrigenda (if
any).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
Endorsement notice
The text of the International Standard IEC 60317-70-1:2020 was approved by CENELEC as a
European Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standards
indicated:
IEC 60264 (series) NOTE Harmonized as EN 60264 (series)
IEC 60317 (series) NOTE Harmonized as EN 60317 (series)
IEC 60851 (series) NOTE Harmonized as EN 60851 (series)
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1 Where an International Publication has been modified by common modifications, indicated by (mod), the relevant
EN/HD applies.
NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available here:
www.cenelec.eu.
Publication Year Title EN/HD Year
IEC 60317-0-10 2017 Specifications for particular types of winding EN 60317-0-10 2017
wires - Part 0-10: General requirements -
Polyester glass-fibre wound fused,
unvarnished, or resin or varnish
impregnated, bare or enamelled round
copper wire
IEC 60317-70-1 ®
Edition 1.0 2020-06
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Specifications for particular types of winding wires –
Part 70-1: Polyester glass-fibre wound unvarnished and fused, bare or
enamelled round copper wire, temperature index 155
Spécifications pour types particuliers de fils de bobinage –
Partie 70-1: Fil de section circulaire en cuivre nu ou émaillé, guipé de fibres
de verre polyester fondues non vernies, d'indice de température 155
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 29.060.10 ISBN 978-2-8322-8420-9
– 2 – IEC 60317-70-1:2020 © IEC 2020
CONTENTS
FOREWORD . 3
INTRODUCTION . 5
1 Scope . 6
2 Normative references . 6
3 Terms, definitions, general notes and appearance . 6
3.1 Terms and definitions . 6
3.2 General notes . 6
3.2.1 Methods of test . 6
3.2.2 Winding wire . 6
3.3 Appearance . 7
4 Dimensions. 7
5 Electrical resistance . 7
6 Elongation . 7
7 Springiness . 7
8 Flexibility and adherence . 7
9 Heat shock . 7
10 Cut-through . 7
11 Resistance to abrasion . 8
12 Resistance to solvents . 8
13 Breakdown voltage . 8
14 Continuity of insulation . 8
15 Temperature index . 8
16 Resistance to refrigerants . 8
17 Solderability . 8
18 Heat or solvent bonding . 8
19 Dielectric dissipation factor . 8
20 Resistance to hydrolysis and to transformer oil . 8
21 Loss of mass . 8
23 Pin hole test . 8
30 Packaging . 9
Bibliography . 10
IEC 60317-70-1:2020 © IEC 2020 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES –
Part 70-1: Polyester glass-fibre wound unvarnished and fused,
bare or enamelled round copper wire, temperature index 155
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the public
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.