EN 60873-1:2004
(Main)Electrical and pneumatic analogue chart recorders for use in industrial-process control systems - Part 1: Methods for performance evaluation
Electrical and pneumatic analogue chart recorders for use in industrial-process control systems - Part 1: Methods for performance evaluation
Applies to the programming of program-mable controller systems using the programming languages defined in EN 61131-3. It also provides guidelines for the implementation of these languages in programmable controller systems and their programming support environments (PSEs).
Elektrische und pneumatische analoge Streifenschreiber zum Einsatz in Systemen industrieller Prozessleittechnik - Teil 1: Verfahren zu Bewertung des Betriebsverhaltens
Enregistreurs analogiques électriques et pneumatiques sur papier diagramme, utilisés dans les systèmes de commande des processus industriels - Partie 1: Méthodes d’évaluation des performances
Applies to the programming of program-mable controller systems using the programming languages defined in EN 61131-3. It also provides guidelines for the implementation of these languages in programmable controller systems and their programming support environments (PSEs).
Electrical and pneumatic analogue chart recorders for use in industrial-process control systems - Part 1: Methods for performance evaluation
General Information
Relations
Standards Content (Sample)
SLOVENSKI SIST EN 60873-1:2004
STANDARD
junij 2004
Electrical and pneumatic analogue chart recorders for use in industrial-process
control systems - Part 1: Methods for performance evaluation
ICS 25.040.40 Referenčna številka
© Standard je založil in izdal Slovenski inštitut za standardizacijo. Razmnoževanje ali kopiranje celote ali delov tega dokumenta ni dovoljeno
EUROPEAN STANDARD EN 60873-1
NORME EUROPÉENNE
EUROPÄISCHE NORM January 2004
ICS 25.040.40 Supersedes EN 60873:1993
English version
Electrical and pneumatic analogue chart recorders
for use in industrial-process control systems
Part 1: Methods for performance evaluation
(IEC 60873-1:2003)
Enregistreurs de courbes électriques Elektrische und pneumatische analoge
et pneumatiques pour une utilisation Streifenschreiber zum Einsatz
dans les systèmes de processus in Systemen industrieller
industriels Prozessleittechnik
Partie 1 : Méthodes pour l'évaluation Teil 1: Verfahren zu Bewertung
des performances des Betriebsverhaltens
(CEI 60873-1:2003) (IEC 60873-1:2003)
This European Standard was approved by CENELEC on 2003-12-01. CENELEC members are bound to
comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the Central Secretariat or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and
notified to the Central Secretariat has the same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland
and United Kingdom.
CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
Central Secretariat: rue de Stassart 35, B - 1050 Brussels
© 2004 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 60873-1:2004 E
Foreword
The text of document 65B/494/FDIS, future edition 1 of IEC 60873-1, prepared by SC 65B, Devices, of
IEC TC 65, Industrial-process measurement and control, was submitted to the IEC-CENELEC parallel
vote and was approved by CENELEC as EN 60873-1 on 2003-12-01.
This European Standard is to be used in conjunction with EN 61298.
This European Standard supersedes EN 60873:1993.
The main changes with respect to EN 60873:1993 concern the updating of methods for inspection and
routine testing of devices, and recorder testing requirements now comply with EN 61298.
The following dates were fixed:
– latest date by which the EN has to be implemented
at national level by publication of an identical
national standard or by endorsement (dop) 2004-09-01
– latest date by which the national standards conflicting
with the EN have to be withdrawn (dow) 2006-12-01
Annex ZA has been added by CENELEC.
__________
Endorsement notice
The text of the International Standard IEC 60873-1:2003 was approved by CENELEC as a European
Standard without any modification.
__________
- 3 - EN 60873-1:2004
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
NOTE When an international publication has been modified by common modifications, indicated by (mod), the relevant
EN/HD applies.
Publication Year Title EN/HD Year
IEC 60050-351 1998 International Electrotechnical - -
Vocabulary (IEV)
Part 351: Automatic control
IEC 61010-1 2001 Safety requirements for electrical EN 61010-1 2001
equipment for measurement, control, + corr. June 2002
and laboratory use
Part 1: General requirements
IEC 61187 (mod) 1993 Electrical and electronic measuring EN 61187 1994
equipment - Documentation + corr. March 1995
IEC 61298-1 1995 Process measurement and control EN 61298-1 1995
devices - General methods and
procedures for evaluating performance
Part 1: General considerations
IEC 61298-2 1995 Part 2: Tests under reference conditions EN 61298-2 1995
IEC 61298-3 1998 Part 3: Tests for the effects of influence EN 61298-3 1998
quantities
IEC 61298-4 1995 Part 4: Evaluation report content EN 61298-4 1995
INTERNATIONAL IEC
STANDARD
60873-1
First edition
2003-10
Electrical and pneumatic analogue
chart recorders for use in industrial-
process control systems –
Part 1:
Methods for performance evaluation
© IEC 2003 ⎯ Copyright - all rights reserved
No part of this publication may be reproduced or utilized in any form or by any means, electronic or
mechanical, including photocopying and microfilm, without permission in writing from the publisher.
International Electrotechnical Commission, 3, rue de Varembé, PO Box 131, CH-1211 Geneva 20, Switzerland
Telephone: +41 22 919 02 11 Telefax: +41 22 919 03 00 E-mail: inmail@iec.ch Web: www.iec.ch
PRICE CODE
Commission Electrotechnique Internationale
Q
International Electrotechnical Commission
ɆɟɠɞɭɧɚɪɨɞɧɚɹɗɥɟɤɬɪɨɬɟɯɧɢɱɟɫɤɚɹɄɨɦɢɫɫɢɹ
For price, see current catalogue
– 2 – 60873-1 © IEC:2003(E)
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
ELECTRICAL AND PNEUMATIC ANALOGUE CHART RECORDERS
FOR USE IN INDUSTRIAL-PROCESS SYSTEMS –
Part 1: Methods for performance evaluation
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any
equipment declared to be in conformity with an IEC Publication.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 60873-1 has been prepared by subcommittee 65B: Devices, of IEC
technical committee 65: Industrial-process measurement and control.
This first edition of IEC 60873-1 cancels and replaces IEC 60873 (1986) and constitutes a
technical revision.
The main changes with respect to the previous edition concern the updating of methods for
inspection and routine testing of devices, and recorder testing requirements now comply with
IEC 61298.
60873-1 © IEC:2003(E) – 3 –
The text of this standard is based on the following documents:
FDIS Report on voting
65B/494/FDIS 65B/511/RVD
Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.
This standard is to be used in conjunction with IEC 61298.
This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.
The committee has decided that the contents of this publication will remain unchanged until
2009. At this date, the publication will be
• reconfirmed;
• withdrawn;
• replaced by a revised edition, or
• amended.
A bilingual version of this publication may be issued at a later date.
– 4 – 60873-1 © IEC:2003(E)
INTRODUCTION
The methods of evaluation specified in this part of IEC 60873 are intended for use by
manufacturers to determine the performance of their products and by users or independent
testing establishments to verify manufacturers’ performance specifications.
The test conditions in this standard, for example, the range of ambient temperatures and power
supply, represent those which commonly arise in use. Consequently, the values specified
herein shall be used where no other values are specified by the manufacturer.
The tests specified in this standard are not necessarily sufficient for instruments specifically
designed for unusually arduous duties. Conversely, a restricted series of tests may be suitable
for instruments designed to perform within a more limited range of conditions.
It will be appreciated that the closest communication should be maintained between the
evaluating body and the manufacturer. Note should be taken of the manufacturer's
specifications for the instrument when the test programme is being decided, and the
manufacturer should be invited to comment on both the test programmes and the results.
60873-1 © IEC:2003(E) – 5 –
ELECTRICAL AND PNEUMATIC ANALOGUE CHART RECORDERS
FOR USE IN INDUSTRIAL-PROCESS SYSTEMS –
Part 1: Methods for performance evaluation
1 Scope and object
This part of IEC 60873 provides methods for determining the performance of all electrical and
pneumatic analogue chart recorders operating from a standardized signal which may be used
in process control. It is intended that continuous and dotted-line traces, multiple-pen and
multiple-channel instruments should be covered. Some tests should not apply to all instruments
and additional tests may be required for certain types of recorders.
The object of this standard is to specify uniform methods of test for the evaluation of the
performance of electrical and pneumatic analogue chart recorders operating from a
standardized signal which may be used in process control.
When a full evaluation in accordance with this standard is not required, those tests which are
required should be performed and the results reported in accordance with those parts of the
standard which are relevant. It should be made clear in such a report that the evaluation
reported is not a full evaluation and the parts omitted should be indicated.
2 Normative references
The following referenced documents are indispensable for the application of this document. For
dated references, only the edition cited applies. For undated references, the latest edition of
the referenced document (including any amendments) applies.
IEC 60050-351:1998, International Electrotechnical Vocabulary (IEV) – Part 351: Automatic
control
IEC 61010-1:2001, Safety requirements for electrical equipment for measurement, control, and
laboratory use – Part 1: General requirements
IEC 61187:1993, Electric and electronic measuring equipment − Documentation
IEC 61298-1:1995, Process measurement and control devices – General methods and
procedures for evaluating performance – Part 1: General considerations
IEC 61298-2:1995, Process measurement and control devices – General methods and
procedures for evaluation performance – Part 2: Tests under reference conditions
IEC 61298-3:1998, Process measurement and control devices – General methods and
procedures for evaluation performance – Part 3: Tests for the effects of influence quantities
IEC 61298-4:1995, Process measurement and control devices – General methods and
procedures for evaluation performance – Part 4: Evaluation report content
– 6 – 60873-1 © IEC:2003(E)
3 Terms and definitions
For the purposes of this document, the terms and definitions given in IEC 60050-351 and in
IEC 61298-1, IEC 61298-2 and IEC 61298-3 together with the following additional definitions,
apply.
3.1
friction effect
in the case of continuous line recorders, effect which friction of the marking device on the chart
may have on the record even though the chart is moving slowly
3.2
measuring range
region between the limits within which a quantity is measured, or received, expresse
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.