Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 3-54: Examinations and measurements - Angular misalignment between ferrule bore axis and ferrule axis for cylindrical ferrules

IEC 61300-3-54:2019 describes the procedure to measure the angular misalignment between the ferrule bore axis and the outside diameter datum axis of a cylindrical ferrule. Keywords: ferrule bore, angular misalignment

Lichtwellenleiter - Verbindungselemente und passive Bauteile – Grundlegende Prüf- und Messverfahren - Teil 3 54: Untersuchungen und Messungen - Winkelversatz zwischen Ferrulenbohrungsachse und Ferrulenachse für zylindrische Ferrulen

Dispositifs d'interconnexion et composants passifs fibroniques - Procédures fondamentales d'essais et de mesures - Partie 3-54: Examens et mesures - Erreur d'alignement angulaire entre l'axe de l'alésage de férule et l'axe de férule pour les férules cylindriques

IEC 61300-3-54:2019 décrit la procédure de mesure de l'erreur d'alignement angulaire entre l'axe de l'alésage de férule et l'axe de référence du diamètre extérieur d'une férule cylindrique. Mot clés: alésage de férule, erreur d'alignement angulaire

Optični spojni elementi in pasivne komponente - Postopki osnovnega preskušanja in meritev - 3-54. del: Preiskave in meritve - Kotna neporavnanost med osjo odprtine tulke in osmi tulk pri cilindričnih tulkah (IEC 61300-3-54:2019)

Ta dokument opisuje postopek za merjenje kotnega zamika med osjo izvrtine tulke in osjo zunanjega premera cilindrične tulke.

General Information

Status
Published
Publication Date
29-Aug-2019
Withdrawal Date
11-Aug-2022
Current Stage
6060 - Document made available - Publishing
Start Date
30-Aug-2019
Completion Date
30-Aug-2019

Buy Standard

Standard
EN IEC 61300-3-54:2019
English language
16 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI STANDARD
01-november-2019
Optični spojni elementi in pasivne komponente - Postopki osnovnega preskušanja
in meritev - 3-54. del: Preiskave in meritve - Kotna neporavnanost med osjo
odprtine tulke in osmi tulk pri cilindričnih tulkah (IEC 61300-3-54:2019)
Fibre optic interconnecting devices and passive components - Basic test and
measurement procedures - Part 3-54: Examinations and measurements - Angular
misalignment between ferrule bore axis and ferrule axes for cylindrical ferrules (IEC
61300-3-54:2019)
Lichtwellenleiter-Verbindungselemente und passive Bauteile – Grundlegende Prüf- und
Messverfahren - Teil 3 54: Untersuchungen und Messungen - Winkelversatz zwischen
Ferrulenbohrungsachse und Ferrulenachse für zylindrische Ferrulen (IEC 61300-3-
54:2019)
Dispositifs d'interconnexion et composants passifs fibroniques - Procédures
fondamentales d'essais et de mesures - Partie 3-54: Examens et mesures - Erreur
d'alignement angulaire entre l'axe de l'alésage de férule et l'axe de férule pour les férules
cylindriques (IEC 61300-3-54:2019)
Ta slovenski standard je istoveten z: EN IEC 61300-3-54:2019
ICS:
33.180.20 Povezovalne naprave za Fibre optic interconnecting
optična vlakna devices
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD EN IEC 61300-3-54

NORME EUROPÉENNE
EUROPÄISCHE NORM
August 2019
ICS 33.180.10
English Version
Fibre optic interconnecting devices and passive components -
Basic test and measurement procedures - Part 3-54:
Examinations and measurements - Angular misalignment
between ferrule bore axis and ferrule axis for cylindrical ferrules
(IEC 61300-3-54:2019)
Dispositifs d'interconnexion et composants passifs Lichtwellenleiter - Verbindungselemente und passive
fibroniques - Procédures fondamentales d'essais et de Bauteile - Grundlegende Prüf- und Messverfahren - Teil 3
mesures - Partie 3-54: Examens et mesures - Erreur 54: Untersuchungen und Messungen - Winkelversatz
d'alignement angulaire entre l'axe de l'alésage de férule et zwischen Ferrulenbohrungsachse und Ferrulenachse für
l'axe de férule pour les férules cylindriques zylindrische Ferrulen
(IEC 61300-3-54:2019) (IEC 61300-3-54:2019)
This European Standard was approved by CENELEC on 2019-08-12. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.

European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 61300-3-54:2019 E

European foreword
The text of document 86B/4203/FDIS, future edition 1 of IEC 61300-3-54, prepared by SC 86B "Fibre
optic interconnecting devices and passive components" of IEC/TC 86 "Fibre optics" was submitted to
the IEC-CENELEC parallel vote and approved by CENELEC as EN IEC 61300-3-54:2019.
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2020-05-12
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2022-08-12
document have to be withdrawn
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.

Endorsement notice
The text of the International Standard IEC 61300-3-54:2019 was approved by CENELEC as a
European Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standards
indicated:
IEC 61300-3-26  NOTE  Harmonized as EN 61300-3-26
IEC 61755-3-1 NOTE Harmonized as EN 61755-3-1
IEC 61755-3-2 NOTE Harmonized as EN 61755-3-2
ISO 2538-1 NOTE Harmonized as EN ISO 2538-1

Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1  Where an International Publication has been modified by common modifications, indicated by (mod), the relevant
EN/HD applies.
NOTE 2  Up-to-date information on the latest versions of the European Standards listed in this annex is available here:
www.cenelec.eu.
Publication Year Title EN/HD Year
ISO 1938-1 -  Geometrical product specifications (GPS) – EN ISO 1938-1 -
Dimensional measuring equipment – Part
1: Plain limit gauges of linear size

IEC 61300-3-54 ®
Edition 1.0 2019-07
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Fibre optic interconnecting devices and passive components – Basic test and

measurement procedures –
Part 3-54: Examinations and measurements – Angular misalignment between

ferrule bore axis and ferrule axis for cylindrical ferrules

Dispositifs d'interconnexion et composants passifs fibroniques – Procédures

fondamentales d'essais et de mesures –

Partie 3-54: Examens et mesures – Erreur d'alignement angulaire entre l'axe de

l'alésage de férule et l'axe de férule pour les férules cylindriques

INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 33.180.10 ISBN 978-2-8322-7099-8

– 2 – IEC 61300-3-54:2019  IEC 2019
CONTENTS
FOREWORD . 3
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 5
4 General description . 6
5 Apparatus . 6
5.1 General . 6
5.2 Pin gauge . 6
5.3 Ferrule holder . 7
5.4 Microscope with video camera . 7
5.5 Precision alignment stage . 7
5.6 Display . 7
5.7 Computer . 7
6 Procedure . 7
7 Details to be specified . 8
Annex A (informative) Measurement uncertainty . 9
A.1 General . 9
A.2 Precision alignment stage accuracy . 9
A.3 Misalignment between ferrule holder axis and camera axis . 10
A.4 Image plane resolution per pixel . 10
A.5 Ferrule bore eccentricity . 11
A.6 Clearance between ferrule bore diameter and gauge diameter . 11
A.7 Summary of measurement uncertainty . 12
Bibliography . 13

Figure 1 – Angular misalignment between ferrule bore axis and ferrule outside
diameter datum axis. 6
Figure 2 – Example of test apparatus . 6
Figure A.1 – Diagram of error caused by the precision alignment stage accuracy . 9
Figure A.2 – Diagram of error caused by the misalignment between the ferrule holder
axis and the camera axis . 10
Figure A.3 – Diagram of error caused by the image plane resolution per pixel . 11
Figure A.4 – Diagram of error caused by the ferrule bore eccentricity . 11
Figure A.5 – Diagram of error caused by the clearance between the ferrule bore
diameter and the pin gauge diameter . 12

Table A.1 – Example of measurement uncertainty summary . 12

IEC 61300-3-54:2019  IEC 2019 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
FIBRE OPTIC INTERCONNECTING
DEVICES AND PASSIVE COMPONENTS –
BASIC TEST AND MEASUREMENT PROCEDURES –

Part 3-54: Examinations and measurements –
Angular misalignment between ferrule bore axis
and ferrule axis for cylindrical ferrules

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international
co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and
in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports,
Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their
preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with
may participate in this preparatory work. International, governmental and non-governmental organizations liaising
with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for
Standardization (ISO) in accordance with conditions determined by agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence between
any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.