EN IEC 62149-3:2020
(Main)Fibre optic active components and devices - Performance standards - Part 3: Modulator-integrated laser diode transmitters for 40-Gbit/s fibre optic transmission systems
Fibre optic active components and devices - Performance standards - Part 3: Modulator-integrated laser diode transmitters for 40-Gbit/s fibre optic transmission systems
IEC 62149-3:2014 covers the performance specification for optical modulators monolithically integrated with laser diodes for 2,5 Gbit/s to 40 Gbit/s multi-channel fibre optic transmission systems. This performance standard contains a definition of the product performance requirements together with a series of sets of tests and measurements with clearly defined conditions, severities and pass/fail criteria. The tests are intended to be run as an initial design verification to prove any product's ability to satisfy the performance standard's requirements. This standard is only applicable for on-off keying format. This second edition cancels and replaces the first edition published in 2004 and constitutes a technical revision. The significant technical change with respect to the previous edition is as follows: The performance standards covered by this standard are now extended to a 40 Gb/s-class system from their original 2,5 Gb/s. Keywords: optical modulators monolithically integrated, laser diodes, 2,5 Gbit/s to 40 Gbit/s multi-channel fibre optic transmission systems
Aktive Lichtwellenleiterbauelemente und -geräte - Betriebsverhalten - Teil 3: Sender mit modulatorintegrierten Laserdioden für 40 Gbit/s-Lichtwellenleiter-Übertragungssysteme
Composants et dispositifs actifs fibroniques - Normes de performances - Partie 3: Émetteurs à diodes laser à modulateur intégré pour systèmes de transmission fibroniques 40 Gbit/s
L'IEC 62149-3:2014 couvre les spécifications de performance concernant les modulateurs optiques avec diodes laser intégrées de façon monolithique, destinés à des systèmes de transmission à fibres optiques à canaux multiples de 2,5 Gbit/s à 40 Gbit/s. La présente norme de performance donne une définition des exigences de performances de produits, ainsi qu'une série d'ensembles d'essais et de mesures, avec des conditions, des sévérités et des critères d'acceptation/de rejet clairement définis. Les essais sont prévus pour être réalisés à titre de vérification initiale de conception, pour prouver la capacité des produits à satisfaire aux exigences des normes de performance. La présente norme n'est applicable qu'au format de codage binaire. Cette deuxième édition annule et remplace la première édition parue en 2004, dont elle constitue une révision technique. La modification technique significative par rapport à l'édition précédente concerne les standards de performance couverts par la présente norme qui sont maintenant élargies pour inclure les systèmes de classe 40 Gb/s à partir des valeurs originales des systèmes 2,5 Gb/s. Mots clés: modulateurs optiques avec diodes laser intégrées de façon monolithique, diodes laser, systèmes de transmission à fibres optiques à canaux multiples de 2,5 Gbit/s à 40 Gbit/s
Aktivne komponente in naprave optičnih vlaken - Izvedbeni standardi - 3. del: Laserski diodni oddajniki z integriranim modulatorjem za optične prenosne sisteme 40-Gbit/s (IEC 62149-3:2020)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-december-2020
Nadomešča:
SIST EN 62149-3:2015
Aktivne komponente in naprave optičnih vlaken - Izvedbeni standardi - 3. del:
Laserski diodni oddajniki z integriranim modulatorjem za optične prenosne
sisteme 40-Gbit/s (IEC 62149-3:2020)
Fibre optic active components and devices - Performance standards - Part 3: Modulator-
integrated laser diode transmitters for 40-Gbit/s fibre optic transmission systems (IEC
62149-3:2020)
Aktive Lichtwellenleiterbauelemente und -geräte - Betriebsverhalten - Teil 3: Sender mit
modulatorintegrierten Laserdioden für 40 Gbit/s-Lichtwellenleiter-Übertragungssysteme
(IEC 62149-3:2020)
Composants et dispositifs actifs fibroniques - Normes de performances - Partie 3:
Émetteurs à diodes laser à modulateur intégré pour systèmes de transmission
fibroniques 40 Gbit/s (IEC 62149-3:2020)
Ta slovenski standard je istoveten z: EN IEC 62149-3:2020
ICS:
33.180.20 Povezovalne naprave za Fibre optic interconnecting
optična vlakna devices
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD EN IEC 62149-3
NORME EUROPÉENNE
EUROPÄISCHE NORM
September 2020
ICS 33.180.20 Supersedes EN 62149-3:2014 and all of its amendments
and corrigenda (if any)
English Version
Fibre optic active components and devices - Performance
standards - Part 3: Modulator-integrated laser diode transmitters
for 40-Gbit/s fibre optic transmission systems
(IEC 62149-3:2020)
Composants et dispositifs actifs fibroniques - Normes de Aktive Lichtwellenleiterbauelemente und -geräte -
performances - Partie 3: Émetteurs à diodes laser à Betriebsverhalten - Teil 3: Sender mit modulatorintegrierten
modulateur intégré pour systèmes de transmission Laserdioden für 40 Gbit/s-Lichtwellenleiter-
fibroniques 40 Gbit/s Übertragungssysteme
(IEC 62149-3:2020) (IEC 62149-3:2020)
This European Standard was approved by CENELEC on 2020-08-11. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2020 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 62149-3:2020 E
European foreword
The text of document 86C/1666/FDIS, future edition 3 of IEC 62149-3, prepared by SC 86C "Fibre
optic systems and active devices" of IEC/TC 86 "Fibre optics" was submitted to the IEC-CENELEC
parallel vote and approved by CENELEC as EN IEC 62149-3:2020.
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2021-05-11
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2023-08-11
document have to be withdrawn
This document supersedes EN 62149-3:2014 and all of its amendments and corrigenda (if any).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
Endorsement notice
The text of the International Standard IEC 62149-3:2020 was approved by CENELEC as a European
Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standards
indicated:
IEC 60068 (series) NOTE Harmonized as EN 60068 (series)
IEC 60793 (series) NOTE Harmonized as EN IEC 60793 (series)
IEC 60825 (series) NOTE Harmonized as EN 60825 (series)
IEC 60874 (series) NOTE Harmonized as EN 60874 (series)
IEC 61280 (series) NOTE Harmonized as EN 61280 (series)
IEC 62007-2 NOTE Harmonized as EN 62007-2
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1 Where an International Publication has been modified by common modifications, indicated by (mod), the relevant
EN/HD applies.
NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available here:
www.cenelec.eu.
Publication Year Title EN/HD Year
IEC 60068-2-1 - Environmental testing - Part 2-1: Tests - Test EN 60068-2-1 -
A: Cold
IEC 60068-2-2 - Environmental testing - Part 2-2: Tests - Test EN 60068-2-2 -
B: Dry heat
IEC 60068-2-6 - Environmental testing - Part 2-6: Tests - Test EN 60068-2-6 -
Fc: Vibration (sinusoidal)
IEC 60068-2-14 - Environmental testing - Part 2-14: Tests - EN 60068-2-14 -
Test N: Change of temperature
IEC 60068-2-27 - Environmental testing - Part 2-27: Tests - EN 60068-2-27 -
Test Ea and guidance: Shock
IEC 60068-2-78 - Environmental testing - Part 2-78: Tests - EN 60068-2-78 -
Test Cab: Damp heat, steady state
IEC 60749-7 - Semiconductor devices - Mechanical and EN 60749-7 -
climatic test methods - Part 7: Internal
moisture content measurement and the
analysis of other residual gases
IEC 60749-26 - Semiconductor devices - Mechanical and EN IEC 60749-26 -
climatic test methods - Part 26: Electrostatic
discharge (ESD) sensitivity testing - Human
body model (HBM)
IEC 60825-1 - Safety of laser products - Part 1: Equipment EN 60825-1 -
classification and requirements
IEC 60950-1 - Information technology equipment - Safety - EN 60950-1 -
Part 1: General requirements
IEC 62007-1 - Semiconductor optoelectronic devices for EN 62007-1 -
fibre optic system applications - Part 1:
Specification template for essential ratings
and characteristics
IEC 62572-3 - Fibre optic active components and devices - EN 62572-3 -
Reliability standards - Part 3: Laser modules
used for telecommunication
ITU-T G.694-1 - Spectral grids for WDM applications: DWDM - -
frequency grid
ITU-T G.957 - Optical interfaces for equipments and - -
systems relating to the synchronous digital
hierarchy
MIL-STD-883-1 - U.S. Department of Defense - Test method - -
standard - Environmental test methods for
microcircuits, Part 1: Test methods 1000-
IEC 62149-3 ®
Edition 3.0 2020-07
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Fibre optic active components and devices – Performance standards –
Part 3: Modulator-integrated laser diode transmitters for 40-Gbit/s fibre optic
transmission systems
Composants et dispositifs actifs fibroniques – Normes de performances –
Partie 3: Émetteurs à diodes laser à modulateur intégré pour systèmes de
transmission fibroniques 40 Gbit/s
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 33.180.20 ISBN 978-2-8322-8591-6
– 2 – IEC 62149-3:2020 © IEC 2020
CONTENTS
FOREWORD . 3
INTRODUCTION . 5
1 Scope . 6
2 Normative references . 6
3 Terms, definitions and abbreviated terms . 7
3.1 Terms and definitions . 7
3.2 Abbreviated terms . 7
4 Product parameters . 7
4.1 Absolute limiting ratings . 7
4.2 Operating environment . 8
4.3 Functional specification. 8
4.4 Diagrams . 10
5 Testing . 10
5.1 General . 10
5.2 Characterization testing . 10
5.3 Performance testing . 12
6 Environmental specifications . 13
6.1 General safety . 13
6.2 Laser safety . 14
Bibliography . 15
Figure 1 – Schematic diagram . 10
Table 1 – Absolute limiting ratings . 8
Table 2 – Operating environment . 8
Table 3 – Operating conditions for functional specification . 9
Table 4 – Functional specification . 9
Table 5 – Characterization tests . 11
Table 6 – Performance test plan . 12
Table 7 – Recommended performance test failure criteria . 13
IEC 62149-3:2020 © IEC 2020 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
FIBRE OPTIC ACTIVE COMPONENTS AND DEVICES –
PERFORMANCE STANDARDS –
Part 3: Modulator-integrated laser diode transmitters
for 40-Gbit/s fibre optic transmission systems
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international
co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and
in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports,
Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their
preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with
may participate in this preparatory work. International, governmental and non-governmental organizations liaising
with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for
Standardization (ISO) in accordance with conditions determined by agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.