EN 60286-2:2015

Packaging of components for automatic handling - Part 2: Tape packaging of components with unidirectional leads on continuous tapes

IEC 60286-2:2015 applies to the tape packaging of components with two or more unidirectional leads for use in electronic equipment. In general, the tape is applied to the component leads. It covers requirements for taping techniques used with equipment for automatic handling, pre-forming of leads, insertion and other operations and includes only those dimensions which are essential to the taping of components intended for the above-mentioned purposes. This edition includes the following significant changes with respect to the previous edition: - A complete revision of the structure and reworked layout. - A two page overview containing a clear overview of all symbols and references. - Addition of annexes of known radial tape formats. - Improved figures.

Gurtung und Magazinierung von Bauelementen für automatische Verarbeitung – Teil 2: Gurtung von Bauelementen mit einseitig herausgeführten Anschlussdrähten

Emballage de composants pour opérations automatisées - Partie 2: Emballage des composants à sorties unilatérales en bandes continues

L'IEC 60286-2:2015 s'applique à l'emballage des composants à deux sorties unilatérales ou plus utilisés dans les équipements électroniques. En général, la bande est appliquée aux sorties des composants. Elle spécifie les exigences relatives aux techniques de mise sur bande applicables pour l'utilisation des équipements de manutention, de préformage des sorties, d'insertion et d'autres opérations automatiques. Elle fournit uniquement les dimensions essentielles pour la mise sur bande de composants destinés aux opérations mentionnées ci-dessus. Cette édition inclut les modifications majeures suivantes par rapport à l'édition précédente: - Révision complète de la structure et modification de la présentation. - Vue d'ensemble de deux pages contenant un aperçu clair de tous les symboles et références. - Ajout d'annexes en formats de bandes radiales connus. - Amélioration des figures.

Pakiranje komponent za avtomatsko ravnanje - 2. del: Pakiranje komponent z enostranskimi priključki na neprekinjenih trakovih

Ta del standarda IEC 60286 se uporablja za tračno pakiranje komponent z dvema ali več enostranskimi priključki za uporabo v elektronski opremi. V splošnem se trak nanese na priključke komponent.
Standard zajema zahteve za tehnike tračnega pakiranja, ki se uporabljajo z opremo za samodejno upravljanje, predobdelavo priključkov, vstavljanje in druge operacije, in vključuje samo tiste dimenzije, ki so bistvene za tračno pakiranje komponent, ki se uporabljajo za zgoraj omenjene namene.

General Information

• Status: Published
• Publication Date: 04-Jun-2015
• Withdrawal Date: 26-May-2018
• ICS: 31.020 - Electronic components in general
• ICS: 31.240 - Mechanical structures for electronic equipment
• Technical Committee: CLC/SR 40 - Capacitors and resistors for electronic equipment
• Drafting Committee: IEC/TC 40 - IEC_TC_40
• Current Stage: 6060 - Document made available - Publishing
• Start Date: 05-Jun-2015
• Completion Date: 05-Jun-2015
• Ref Project: SIST EN 60286-2:2015 - Packaging of components for automatic handling - Part 2: Packaging of components with unidirectional leads on continuous tapes

Relations

• Replaces: EN 60286-2:2009 - Packaging of components for automatic handling - Part 2: Packaging of components with unidirectional leads on continuous tapes
• Effective Date: 28-Jan-2023
• Replaced By: EN IEC 60286-2:2022 - Packaging of components for automatic handling - Part 2: Tape packaging of components with unidirectional leads on continuous tapes
• Effective Date: 02-Mar-2021

Standards Content (Sample)

SLOVENSKI STANDARD
01-september-2015
1DGRPHãþD
SIST EN 60286-2:2009
3DNLUDQMHNRPSRQHQW]DDYWRPDWVNRUDYQDQMHGHO3DNLUDQMHNRPSRQHQW]
HQRVWUDQVNLPLSULNOMXþNLQDQHSUHNLQMHQLKWUDNRYLK
Packaging of components for automatic handling - Part 2: Packaging of components with
unidirectional leads on continuous tapes
Gurtung und Magazinierung von Bauelementen für automatische Verarbeitung – Teil 2:
Gurtung von Bauelementen mit einseitig herausgeführten Anschlussdrähten
Emballage de composants pour opérations automatisées - Partie 2: Emballage des
composants à sorties unilatérales en bandes continues
Ta slovenski standard je istoveten z: EN 60286-2:2015
ICS:
31.020 Elektronske komponente na Electronic components in
splošno general
55.020 Pakiranje in distribucija blaga Packaging and distribution of
na splošno goods in general
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD EN 60286-2
NORME EUROPÉENNE
EUROPÄISCHE NORM
June 2015
ICS 31.240; 31.020 Supersedes EN 60286-2:2009
English Version
Packaging of components for automatic handling - Part 2:
Packaging of components with unidirectional leads on
continuous tapes
(IEC 60286-2:2015)
Emballage de composants pour opérations automatisées - Gurtung und Magazinierung von Bauelementen für
Partie 2: Emballage des composants à sorties unilatérales automatische Verarbeitung - Teil 2: Gurtung von
en bandes continues Bauelementen mit einseitig herausgeführten
(IEC 60286-2:2015) Anschlussdrähten
(IEC 60286-2:2015)
This European Standard was approved by CENELEC on 2015-05-27. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.

European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2015 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN 60286-2:2015 E
Foreword
The text of document 40/2343/FDIS, future edition 4 of IEC 60286-2, prepared by IEC/TC 40
"Capacitors and resistors for electronic equipment" was submitted to the IEC-CENELEC parallel vote
and approved by CENELEC as EN 60286-2:2015.
The following dates are fixed:
(dop) 2016-02-27
• latest date by which the document has to be implemented at
national level by publication of an identical national
standard or by endorsement
(dow) 2018-05-27
• latest date by which the national standards conflicting with
the document have to be withdrawn

This document supersedes EN 60286-2:2009.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such
patent rights.
Endorsement notice
The text of the International Standard IEC 60286-2:2015 was approved by CENELEC as a European
Standard without any modification.
In the official version, for Bibliography, the following note has to be added for the standard indicated:
ISO 11469:2000 NOTE Harmonized as EN ISO 11469:2000.

- 3 - EN 60286-2:2015
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.
NOTE 1 When an International Publication has been modified by common modifications, indicated by (mod), the relevant
EN/HD applies.
NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available here:
www.cenelec.eu.
Publication Year Title EN/HD Year

IEC 60097 1991 Grid systems for printed circuits EN 60097 1993
IEC 60301 -  Preferred diameters of wire terminations of EN 60301 -
capacitors and resistors
IEC 60286-2 ®
Edition 4.0 2015-04
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Packaging of components for automatic handling –

Part 2: Tape packaging of components with unidirectional leads on continuous

tapes
Emballage de composants pour opérations automatisées –

Partie 2: Emballage des composants à sorties unilatérales en bandes continues

INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 31.020; 31.240 ISBN 978-2-8322-2595-0

– 2 – IEC 60286-2:2015 © IEC 2015
CONTENTS
FOREWORD . 5
1 Scope . 7
2 Normative references . 7
3 Terms, definitions and symbols . 7
3.1 Terms and definitions . 7
3.2 Symbols . 10
4 Dimensions . 13
4.1 Tape width dimensions (W, W , W , W ) . 13
0 1 2
4.1.1 Tape width (W) . 13
4.1.2 Hold-down tape width (W ) . 13
4.1.3 Distance between the upper edges of the carrier tape and the abscissa
(W ) . 13
4.1.4 Distance between the upper edges of the carrier tape and the hold-down

tape (W ) . 13
4.2 Components and sprocket hole pitches (P, P , P , P , D ) . 13
0 1 2 0
4.2.1 General . 13
4.2.2 Pitch between two consecutive mutual components (P) . 13
4.2.3 Pitch between two consecutive sprocket holes (P ) . 13
4.2.4 Distance between the ordinate and the first lead of the component on the
drawer side (for components with two leads) (P ) . 14
4.2.5 Distance between the ordinate and the center lead of the component on
the drawer side (for components with three leads) (P ) . 14
4.2.6 Sprocket hole diameter (D ) . 14
4.3 Dimensions for component position relative to the abscissa (H, H , H , H ,
0 1 2
H ) . 14
4.3.1 Distance between the abscissa and the bottom plane of the component
body (H). 14
4.3.2 Distance between the abscissa and the reference plane of components
with crimped leads (H ) . 14
4.3.3 Distance between the abscissa and the top of the body of the
components (H ) . 14
4.3.4 Distance between the abscissa and the tip of the short terminal without
tape (H ) . 14
4.3.5 Distance between the bottom of the component and the tip of the short
terminal without tape (H ) . 14
4.4 Lead terminal dimensions (d, d , F, F , F , L, K) and tape thickness (T, T ) . 15
1 1 2 1
4.4.1 Dimensions and tolerances of lead spacing for two leaded components
(F) and for three leaded components (F , F ) . 15
1 2
4.4.2 Lead terminal diameter (d, d ) . 15
4.4.3 Tape thickness (T, T ) . 15
4.4.4 Maximum permissible protrusion of the ends of the leads (L) . 15
4.4.5 Distance between the lead terminal and the short terminal without tape
(K) . 15
4.5 Maximum permissible deviation of taped component dimensions . 16
4.5.1 Maximum permissible deviation of taped component dimensions (∆h, ∆p,
∆P ) . 16
5 Taping . 16
5.1 Taping dimensions . 16
5.2 Splices . 16

IEC 60286-2:2015 © IEC 2015 – 3 –
5.3 Tape leader and trailer . 17
6 Tape . 17
6.1 Polarization direction on tape . 17
6.2 Kinks or bends on tape . 17
6.3 Adhesion to tape and extraction force . 17
6.4 Tape breaking force . 18
6.5 Tape material . 18
6.6 Hold-down tape . 18
6.7 Missing components . 18
7 Packing . 19
7.1 General . 19
7.2 Reel dimensions. 19
7.2.1 Component tape reeling . 20
7.2.2 Components protection . 20
7.2.3 Reel filling . 21
7.3 Maximum dimensions of the fan-fold container . 21
7.4 Recycling . 21
7.5 Marking . 21
Annex A (informative) Dimensions for two leads . 22
A.1 Dimensions for two formed leads, sprocket hole between parts . 22
A.2 Dimensions for two formed leads, sprocket hole between leads . 24
A.3 Dimensions for two straight leads, sprocket hole between parts . 26
A.4 Dimensions for two straight leads, sprocket hole between leads . 28
Annex B (informative) Dimensions for three leads . 30
B.1 Dimensions for three formed leads, sprocket hole between parts . 30
B.2 Dimensions for three formed leads, sprocket hole between leads . 32
Bibliography .
...

SLOVENSKI STANDARD
01-september-2015
Nadomešča:
SIST EN 60286-2:2009
Pakiranje komponent za avtomatsko ravnanje - 2. del: Pakiranje komponent z
enostranskimi priključki na neprekinjenih trakovih
Packaging of components for automatic handling - Part 2: Packaging of components with
unidirectional leads on continuous tapes
Gurtung und Magazinierung von Bauelementen für automatische Verarbeitung – Teil 2:
Gurtung von Bauelementen mit einseitig herausgeführten Anschlussdrähten
Emballage de composants pour opérations automatisées - Partie 2: Emballage des
composants à sorties unilatérales en bandes continues
Ta slovenski standard je istoveten z: EN 60286-2:2015
ICS:
31.020 Elektronske komponente na Electronic components in
splošno general
55.020 Pakiranje in distribucija blaga Packaging and distribution of
na splošno goods in general
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD EN 60286-2
NORME EUROPÉENNE
EUROPÄISCHE NORM
June 2015
ICS 31.240; 31.020 Supersedes EN 60286-2:2009
English Version
Packaging of components for automatic handling - Part 2:
Packaging of components with unidirectional leads on
continuous tapes
(IEC 60286-2:2015)
Emballage de composants pour opérations automatisées - Gurtung und Magazinierung von Bauelementen für
Partie 2: Emballage des composants à sorties unilatérales automatische Verarbeitung - Teil 2: Gurtung von
en bandes continues Bauelementen mit einseitig herausgeführten
(IEC 60286-2:2015) Anschlussdrähten
(IEC 60286-2:2015)
This European Standard was approved by CENELEC on 2015-05-27. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.

European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2015 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN 60286-2:2015 E
Foreword
The text of document 40/2343/FDIS, future edition 4 of IEC 60286-2, prepared by IEC/TC 40
"Capacitors and resistors for electronic equipment" was submitted to the IEC-CENELEC parallel vote
and approved by CENELEC as EN 60286-2:2015.
The following dates are fixed:
(dop) 2016-02-27
• latest date by which the document has to be implemented at
national level by publication of an identical national
standard or by endorsement
(dow) 2018-05-27
• latest date by which the national standards conflicting with
the document have to be withdrawn

This document supersedes EN 60286-2:2009.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such
patent rights.
Endorsement notice
The text of the International Standard IEC 60286-2:2015 was approved by CENELEC as a European
Standard without any modification.
In the official version, for Bibliography, the following note has to be added for the standard indicated:
ISO 11469:2000 NOTE Harmonized as EN ISO 11469:2000.

- 3 - EN 60286-2:2015
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.
NOTE 1 When an International Publication has been modified by common modifications, indicated by (mod), the relevant
EN/HD applies.
NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available here:
www.cenelec.eu.
Publication Year Title EN/HD Year

IEC 60097 1991 Grid systems for printed circuits EN 60097 1993
IEC 60301 -  Preferred diameters of wire terminations of EN 60301 -
capacitors and resistors
IEC 60286-2 ®
Edition 4.0 2015-04
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Packaging of components for automatic handling –

Part 2: Tape packaging of components with unidirectional leads on continuous

tapes
Emballage de composants pour opérations automatisées –

Partie 2: Emballage des composants à sorties unilatérales en bandes continues

INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 31.020; 31.240 ISBN 978-2-8322-2595-0

– 2 – IEC 60286-2:2015 © IEC 2015
CONTENTS
FOREWORD . 5
1 Scope . 7
2 Normative references . 7
3 Terms, definitions and symbols . 7
3.1 Terms and definitions . 7
3.2 Symbols . 10
4 Dimensions . 13
4.1 Tape width dimensions (W, W , W , W ) . 13
0 1 2
4.1.1 Tape width (W) . 13
4.1.2 Hold-down tape width (W ) . 13
4.1.3 Distance between the upper edges of the carrier tape and the abscissa
(W ) . 13
4.1.4 Distance between the upper edges of the carrier tape and the hold-down

tape (W ) . 13
4.2 Components and sprocket hole pitches (P, P , P , P , D ) . 13
0 1 2 0
4.2.1 General . 13
4.2.2 Pitch between two consecutive mutual components (P) . 13
4.2.3 Pitch between two consecutive sprocket holes (P ) . 13
4.2.4 Distance between the ordinate and the first lead of the component on the
drawer side (for components with two leads) (P ) . 14
4.2.5 Distance between the ordinate and the center lead of the component on
the drawer side (for components with three leads) (P ) . 14
4.2.6 Sprocket hole diameter (D ) . 14
4.3 Dimensions for component position relative to the abscissa (H, H , H , H ,
0 1 2
H ) . 14
4.3.1 Distance between the abscissa and the bottom plane of the component
body (H). 14
4.3.2 Distance between the abscissa and the reference plane of components
with crimped leads (H ) . 14
4.3.3 Distance between the abscissa and the top of the body of the
components (H ) . 14
4.3.4 Distance between the abscissa and the tip of the short terminal without
tape (H ) . 14
4.3.5 Distance between the bottom of the component and the tip of the short
terminal without tape (H ) . 14
4.4 Lead terminal dimensions (d, d , F, F , F , L, K) and tape thickness (T, T ) . 15
1 1 2 1
4.4.1 Dimensions and tolerances of lead spacing for two leaded components
(F) and for three leaded components (F , F ) . 15
1 2
4.4.2 Lead terminal diameter (d, d ) . 15
4.4.3 Tape thickness (T, T ) . 15
4.4.4 Maximum permissible protrusion of the ends of the leads (L) . 15
4.4.5 Distance between the lead terminal and the short terminal without tape
(K) . 15
4.5 Maximum permissible deviation of taped component dimensions . 16
4.5.1 Maximum permissible deviation of taped component dimensions (∆h, ∆p,
∆P ) . 16
5 Taping . 16
5.1 Taping dimensions . 16
5.2 Splices . 16

IEC 60286-2:2015 © IEC 2015 – 3 –
5.3 Tape leader and trailer . 17
6 Tape . 17
6.1 Polarization direction on tape . 17
6.2 Kinks or bends on tape . 17
6.3 Adhesion to tape and extraction force . 17
6.4 Tape breaking force . 18
6.5 Tape material . 18
6.6 Hold-down tape . 18
6.7 Missing components . 18
7 Packing . 19
7.1 General . 19
7.2 Reel dimensions. 19
7.2.1 Component tape reeling . 20
7.2.2 Components protection . 20
7.2.3 Reel filling . 21
7.3 Maximum dimensions of the fan-fold container . 21
7.4 Recycling . 21
7.5 Marking . 21
Annex A (informative) Dimensions for two leads . 22
A.1 Dimensions for two formed leads, sprocket hole between parts . 22
A.2 Dimensions for two formed leads, sprocket hole between leads . 24
A.3 Dimensions for two straight leads, sprocket hole between parts . 26
A.4 Dimensions for two straight leads, sprocket hole between leads . 28
Annex B (informative) Dimensions for three leads .
...