EN 50626-2:2023
(Main)Conduit systems buried underground for the protection and management of insulated electrical cables or communication cables - Part 2: Polyethylene (PE), Polypropylene (PP) or Unplasticized poly(vinyl chloride) (PVC-U) conduit systems - Requirements for solid wall conduits, fittings and the system used in special applications
Conduit systems buried underground for the protection and management of insulated electrical cables or communication cables - Part 2: Polyethylene (PE), Polypropylene (PP) or Unplasticized poly(vinyl chloride) (PVC-U) conduit systems - Requirements for solid wall conduits, fittings and the system used in special applications
This European Standard specifies particular requirements and tests for conduit systems buried underground for the protection and management of insulated conductors and/or power cables or communication cables that are installed by different techniques, for example, blowing (including floating), pulling or pushing directly after installation of the conduit or during its expected performance time. This standard is applicable to all conduits with circular cross section manufactured individually or manufactured as a part of an assembly NOTE Reference is made to other documents for additional material requirements where applicable.
Erdverlegte Elektroinstallationsrohrsysteme für den Schutz und die Führung isolierter elektrischer Kabel oder Fernmeldekabel - Teil 2: Elektroinstallationsrohrsysteme aus Polyethylen (PE), Polypropylen (PP) oder weichmacherfreiem Poly(vinylchlorid) (PVC-U) - Anforderungen an Vollwandrohre, Rohrzubehörteile und spezielle Anwendungen
Systèmes de conduits enterrés dans le sol pour la protection et la gestion des câbles électriques isolés ou des câbles de communication - Partie 2: Systèmes de conduits en polyéthylène (PE), en polypropylène (PP) ou en poly(chlorure de vinyle) non plastifié (PVC-U) - Exigences pour les conduits à paroi pleine, les accessoires et le système utilisé dans les applications spéciales
Le présent document spécifie les exigences et les essais applicables aux systèmes de conduits étanches à paroi pleine en PE, PP et PVC-U de section circulaire, fabriqués individuellement ou faisant partie d'un assemblage ayant une durée d’utilisation spécifiée et enterrés dans le sol à une profondeur maximale de 6 m pour la protection et le rangement des conducteurs isolés et/ou des câbles d’alimentation ou des câbles de communication. Les applications qui exigent des systèmes de conduits étanches à paroi pleine sont les suivantes: - l’installation de câbles dans les conduits par soufflage; - l’installation de câbles dans les conduits par flottage; - les installations de conduits sans tranchées. Le présent document s'applique aux conduits avec ou sans emboîture intégrée et accessoires. NOTE 1 Les conduits dans lesquels les câbles ont été installés par soufflage ou par flottage peuvent également être installés suivant des méthodes conventionnelles. NOTE 2 L’installation des câbles peut également être réalisée par tirage et insertion. NOTE 3 Au sein d'un système de conduits thermoplastique, il est possible d’utiliser des accessoires constitués d’autres matériaux, mais ceux-ci ne sont pas spécifiés dans le présent document. NOTE 4 Il est de la responsabilité de l’acheteur ou du prescripteur de prendre en compte toutes les règlements nationaux appropriés et les pratiques ou les codes d'installation lors du choix des produits à installer, en fonction des caractéristiques spécifiées dans le présent document. NOTE 5 Les microconduits sont couverts par la partie correspondante de la série EN 60794.
Podzemni kanalski sistem za zaščito in upravljanje izoliranih električnih ali komunikacijskih kablov - 2. del: Polietilenski (PE), polipropilenski (PP) ali neplastificirani polivinilkloridni (PVC-U) vodovodni sistemi - Zahteve za masivne stenske vodnike, armature in sistem, ki se uporablja v posebnih aplikacijah
Ta evropski standard določa posebne zahteve in preskuse za podzemne kanalske sisteme za zaščito in upravljanje izoliranih vodnikov in/ali napajalnih ali komunikacijskih kablov, ki se vgrajujejo z različnimi tehnikami, na primer s pihanjem (vključno z lebdenjem), vlečenjem ali potiskanjem neposredno po vgradnji vodnika ali med pričakovanim časom delovanja.
Ta standard se uporablja za vse vodnike s krožnim prečnim prerezom, ki so izdelani posamično ali kot del sestava.
OPOMBA: Sklicuje se na druge dokumente zaradi dodatnih zahtev glede materialov, kjer je to ustrezno.
General Information
Standards Content (Sample)
SLOVENSKI STANDARD
01-september-2023
Podzemni kanalski sistem za zaščito in upravljanje izoliranih električnih ali
komunikacijskih kablov - 2. del: Polietilenski (PE), polipropilenski (PP) ali
neplastificirani polivinilkloridni (PVC-U) vodovodni sistemi - Zahteve za masivne
stenske vodnike, armature in sistem, ki se uporablja v posebnih aplikacijah
Conduit systems buried underground for the protection and management of insulated
electrical cables or communication cables - Part 2: Polyethylene (PE), Polypropylene
(PP) or Unplasticized poly(vinyl chloride) (PVC-U) conduit systems - Requirements for
solid wall conduits, fittings and the system used in special applications
Erdverlegte Elektroinstallationsrohrsysteme für den Schutz und die Führung isolierter
elektrischer Kabel oder Fernmeldekabel - Teil 2: Elektroinstallationsrohrsysteme aus
Polyethylen (PE), Polypropylen (PP) oder weichmacherfreiem Poly(vinylchlorid) (PVC-U)
- Anforderungen an Vollwandrohre, Rohrzubehörteile und spezielle Anwendungen
Systèmes de conduits enterrés dans le sol pour la protection et la gestion des câbles
électriques isolés ou des câbles de communication - Partie 2: Systèmes de conduits en
polyéthylène (PE), en polypropylène (PP) ou en poly(chlorure de vinyle) non plastifié
(PVC-U) - Exigences pour les conduits à paroi pleine, les accessoires et le système
utilisé dans les applications spéciales
Ta slovenski standard je istoveten z: EN 50626-2:2023
ICS:
29.120.10 Inštalacijske cevi za Conduits for electrical
električne namene purposes
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD EN 50626-2
NORME EUROPÉENNE
EUROPÄISCHE NORM July 2023
ICS 29.120.10
English Version
Conduit systems buried underground for the protection and
management of insulated electrical cables or communication
cables - Part 2: Polyethylene (PE), Polypropylene (PP) or
Unplasticized poly(vinyl chloride) (PVC-U) conduit systems -
Requirements for solid wall conduits, fittings and the system
used in special applications
Systèmes de conduits enterrés dans le sol pour la Erdverlegte Elektroinstallationsrohrsysteme für den Schutz
protection et la gestion des câbles électriques isolés ou des und die Führung isolierter elektrischer Kabel oder
câbles de communication - Partie 2: Systèmes de conduits Fernmeldekabel - Teil 2: Elektroinstallationsrohrsysteme
en polyéthylène (PE), en polypropylène (PP) ou en aus Polyethylen (PE), Polypropylen (PP) oder
poly(chlorure de vinyle) non plastifié (PVC-U) - Exigences weichmacherfreiem Poly(vinylchlorid) (PVC-U) -
pour les conduits à paroi pleine, les accessoires et le Anforderungen an Vollwandrohre, Rohrzubehörteile und
système utilisé dans les applications spéciales spezielle Anwendungen
This European Standard was approved by CENELEC on 2023-06-19. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Türkiye and the United Kingdom.
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2023 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN 50626-2:2023 E
Contents Page
European foreword . 3
Introduction . 4
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 7
4 Symbols and abbreviations . 7
5 Material . 8
6 General characteristics . 12
7 Geometrical characteristics . 12
8 Mechanical characteristics of conduits . 18
9 Physical characteristics . 22
10 Performance requirements . 26
11 Sealing rings . 26
12 Fire hazard . 26
13 Electromagnetic compatibility . 26
14 Marking and documentation . 27
Annex A (normative) Utilization of non-virgin PVC-U material . 29
A.1 General . 29
A.2 Own reprocessed material from conduits and conduit fittings . 29
A.3 External reprocessed and recycled materials with an agreed specification . 29
Annex B (normative) Utilization of non-virgin PP material . 30
B.1 General . 30
B.2 Own reprocessed material from conduits and conduit fittings . 30
B.3 External reprocessed and recycled materials with an agreed specification . 30
Annex C (normative) Utilization of non-virgin PE material . 31
C.1 General . 31
C.2 Own reprocessed material from conduits and conduit fittings . 31
C.3 External reprocessed and recycled materials with an agreed specification . 31
Annex ZZ (informative) Relationship between this European standard and the safety objectives of
Directive 2014/35/EU [2014 OJ L96] aimed to be covered . 32
Bibliography . 33
European foreword
This document (EN 50626-2:2023) has been prepared by CLC/TC 213, “Cable management systems”.
The following dates are fixed:
• latest date by which this document has to be (dop) 2024-06-19
implemented at national level by publication of
an identical national standard or by
endorsement
• latest date by which the national standards (dow) 2026-06-19
conflicting with this document have to be
withdrawn
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights.
CENELEC shall not be held responsible for identifying any or all such patent rights.
This document has been prepared under a Standardization Request given to CENELEC by the European
Commission and the European Free Trade Association, and supports essential requirements of EU Directive(s) /
Regulation(s).
For relationship with EU Directive(s) / Regulation(s), see informative Annex ZZ, which is an integral part of this
document.
Any feedback and questions on this document should be directed to the users’ national committee. A complete
listing of these bodies can be found on the CENELEC website.
Introduction
CENELEC TC 213 is responsible for the development of the EN 50626 series, which consists of two separate
parts, each covering different products/applications.
This document covers requirements and tests for conduit systems buried underground for the protection and
management of insulated conductors and/or power cables or communication cables having a specified
performance time and which are leak-tight solid wall conduit systems and manufactured in PE, PP and PVC-U.
EN 50626-1 covers requirements and tests for conduit systems buried underground for the protection and
management of insulated conductors and/or power cables or communication cables.
For on-site storage, CEN/TS 1046 can be used as a guidance.
A conduit system buried underground that conforms to this document is deemed to be safe for use.
This is a European Standard for cable management products used for electro-technical purposes. It relates to the
Council Directives on the approximation of laws, regulations and administrative provisions of the Member States
relating to Low Voltage Directive 2014/35/EU through consideration of the essential requirements of this Directive.
This document is supported by separate standards to which references are made.
1 Scope
This document specifies requirements and tests for PE, PP and PVC-U leak-tight solid wall conduit systems with
circular cross section, manufactured individually or as part of an assembly having a specified performance time
and buried underground to a maximum depth of 6 m for the protection and management of insulated conductors
and/or power cables or communication cables.
Applications that require leak-tight solid wall conduit systems are:
— installation of cables in conduits by blowing;
— installation of cables in conduits by floating;
— trenchless installation of conduits.
This document is applicable to conduits with or without integral socket and fittings.
NOTE 1 Conduits in which cables are installed by blowing or floating can also be installed by conventional methods.
NOTE 2 Installation of cables can also be done by pulling and pushing.
NOTE 3 Within a thermoplastic conduit system, fittings made of other materials can be used but they are not specified in
this document.
NOTE 4 It is the responsibility of the purchaser or specifier to take into account any relevant national regulations and
installation practices or codes when selecting the products to be installed, based on the characteristics specified in this
document.
NOTE 5 Microducts are covered by the relevant part of the EN 60794 series.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content constitutes
requirements of this document. For dated references, only the edition cited applies. For undated references, the
latest edition of the referenced document (including any amendments) applies.
EN 681-1:1996, Elastomeric seals - Materials requirements for pipe joint seals used in water and drainage
applications - Part 1: Vulcanized rubber
EN 681-2:2000, Elastomeric Seals - Materials requirements for pipe joint seals used in water and drainage
applications - Part 2: Thermoplastic elastomers
EN 1905:1998, Plastics piping systems - Unplasticized poly(vinyl chloride) (PVC-U) pipes, fittings and material -
Method for assessment of the PVC content based on total chlorine content
EN 12099:1997, Plastics piping systems - Polyethylene piping materials and components - Determination of
volatile content
EN 15346:2014, Plastics - Recycled plastics - Characterization of poly(vinyl chloride) (PVC) recyclates
EN 50626-1:2023, Conduit systems buried underground for the protection and management of insulated electrical
cables or communication cables - Part 1: General requirements
EN ISO 472:2013, Plastics - Vocabulary (ISO 472:2013)
EN ISO 580:2005, Plastics piping and ducting systems - Injection-moulded thermoplastics fittings - Methods for
visually assessing the effects of heating (ISO 580:2005)
EN ISO 1043-1:2011, Plastics - Symbols and abbreviated terms - Part 1: Basic polymers and their special
characteristics (ISO 1043-1:2001)
EN ISO 1133-1:2022, Plastics - Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (M
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.