EN 62841-2-1:2018
(Main)Electric motor-operated hand-held tools, transportable tools and lawn and garden machinery - Safety - Part 2-1: Particular requirements for hand-held drills and impact drills
Electric motor-operated hand-held tools, transportable tools and lawn and garden machinery - Safety - Part 2-1: Particular requirements for hand-held drills and impact drills
IEC 62841-2-1:2017 applies to hand-held drills and impact drills, including diamond core drills. This standard also applies to drills that can be used for driving screws by attaching screwdriver bits.The rated voltage is not more than 250 V for single-phase a.c. or d.c. tools, and 480 V for three-phase a.c. tools. The rated input is not more than 3 700 W. The limits for the applicability of this standard for battery tools are given in K.1 and L.1. This standard deals with the hazards presented by tools which are encountered by all persons in the normal use and reasonably foreseeable misuse of the tools. Hand-held electric tools, which can be mounted on a support or working stand for use as fixed tools without any alteration of the tool itself, are within the scope of this standard and such combination of a hand-held tool and a support is considered to be a transportable tool and thus covered by the relevant Part 3. This standard does not apply to rotary hammers, even if they can be used as a drill. This Part 2-1 is to be used in conjunction with the first edition of IEC 62841-1:2014. The attention of National Committees is drawn to the fact that equipment manufacturers and testing organizations may need a transitional period following publication of a new, amended or revised IEC publication in which to make products in accordance with the new requirements and to equip themselves for conducting new or revised tests. It is the recommendation of the committee that the content of this publication be adopted for implementation nationally not earlier than 36 months from the date of publication Key words: Drill, Impact Drill, Hand-held tool, Safety
Elektrische motorbetriebene handgeführte Werkzeuge, transportable Werkzeuge und Rasen- und Gartenmaschinen - Sicherheit - Teil 2-1: Besondere Anforderungen für handgeführte Bohrmaschinen und Schlagbohrmaschinen
Outils électroportatifs à moteur, outils portables et machines pour jardins et pelouses - Sécurité - Partie 2-1: Exigences particulières pour les perceuses portatives et les perceuses à percussion
IEC 62841-2-1:2017 s’applique aux perceuses portatives et aux perceuses à percussion y compris les perceuses à diamant. La présente norme s’applique également aux perceuses pouvant être utilisées pour enfoncer des vis lorsque des embouts de visseuse leur sont ajoutés. La tension assignée est inférieure à 3 700 W. Les limites d'application de la présente Norme aux outils fonctionnant sur batterie sont indiquées en K.1 et L.1. La présente Norme traite des dangers présentés par les outils, encourus par tous les individus dans l'utilisation normale et dans l'utilisation impropre raisonnablement prévisible de ces outils. Les outils électroportatifs, qui peuvent être montés sur un support de travail pour être utilisés comme outils installés à poste fixe sans aucune modification de l'outil lui-même, sont compris dans le domaine d'application de la présente Norme et la combinaison d'un outil portatif et d'un support est considérée comme un outil portable, donc couvert par la Partie 3 applicable. La présente norme ne s’applique pas aux marteaux rotatifs, même s’ils peuvent être utilisés comme une perceuse. La présente Partie 2-1 doit être utilisée conjointement avec la première édition de l’IEC 62841-1 (2014). L'attention des Comités Nationaux est attirée sur le fait que les fabricants d'appareils et les organismes d'essai peuvent avoir besoin d'une période transitoire après la publication d'une nouvelle publication IEC, ou d'une publication amendée ou révisée, pour fabriquer des produits conformes aux nouvelles exigences et pour adapter leurs équipements aux nouveaux essais ou aux essais révisés. Le comité recommande que le contenu de cette publication soit entériné au niveau national au plus tôt 36 mois après la date de publication. Mots clés: perceuses, perceuses à percussion, outil portatif, sécurité
Elektromotorna ročna orodja, prenosna orodja ter stroji za trato in vrt - Varnost - 2-1. del: Posebne zahteve za ročne vrtalnike in udarne (vibracijske) vrtalnike (IEC 62841-2-1:2017)
IEC 62841-2-1:2017 se uporablja za ročne vrtalnike in udarne vrtalnike, vključno z vrtalniki, ki omogočajo uporabo diamantnih svedrov. Ta standard se uporablja tudi za vrtalnike, ki jih je mogoče uporabljati za vijačenje s pritrditvijo nastavkov vijačnika. Nazivna napetost ne presega 250 V za enofazna orodja na enosmerni ali izmenični tok in 480 V za trifazna orodja na izmenični tok. Nazivna vhodna moč ne presega 3700 W. Omejitve uporabnosti tega standarda za baterijska orodja so podane v točkah K.1 in L.1. Ta standard obravnava tveganja, ki jih predstavljajo orodja in katerim so izpostavljene vse osebe pri običajni uporabi ter pričakovani nepravilni uporabi orodij. Ročna električna orodja, ki jih je mogoče pritrditi na opornik ali delovno stojalo, pri čemer se jih brez kakršnih koli sprememb samega orodja uporablja kot fiksna orodja, spadajo na področje uporabe tega standarda. Kombinacija ročnega orodja in takšnega stojala se obravnava kot prenosno orodje, ki je zajeto v ustreznem 3. delu.
Ta standard se ne uporablja za rotacijska kladiva, tudi če se ta lahko uporabljajo kot vrtalnik.
Ta del 2-1 je treba uporabljati v povezavi s prvo izdajo standarda IEC 62841-1:2014.
Nacionalni odbori morajo upoštevati, da bodo proizvajalci opreme in organizacije za preskušanje morda potrebovali prehodno obdobje po objavi nove, spremenjene ali popravljene objave IEC, da bodo lahko izdelovali izdelke v skladu z novimi zahtevami in se opremili za izvajanje novih ali spremenjenih preskusov.
Odbor priporoča, da se vsebina te objave sprejme v nacionalno uporabo najpozneje 36 mesecev od datuma objave.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 62841-2-1:2018
01-marec-2018
1DGRPHãþD
SIST EN 60745-2-1:2010
(OHNWURPRWRUQDURþQDRURGMDSUHQRVQDRURGMDWHUVWURML]DWUDWRLQYUW9DUQRVW
GHO 3RVHEQH]DKWHYH]DURþQHYUWDOQLNHLQXGDUQH YLEUDFLMVNH YUWDOQLNH ,(&
Electric Motor-Operated Hand-Held Tools, Transportable Tools and Lawn and Garden
Machinery - Safety - Part 2-1: Particular requirements for hand-held drills and impact
drills (IEC 62841-2-1:2017)
Ta slovenski standard je istoveten z: EN 62841-2-1:2018
ICS:
25.080.40 Vrtalniki Drilling machines
25.140.20 (OHNWULþQDRURGMD Electric tools
SIST EN 62841-2-1:2018 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 62841-2-1:2018
---------------------- Page: 2 ----------------------
SIST EN 62841-2-1:2018
EUROPEAN STANDARD EN 62841-2-1
NORME EUROPÉENNE
EUROPÄISCHE NORM
January 2018
ICS 25.140.20 Supersedes EN 60745-2-1:2010
English Version
Electric motor-operated hand-held tools, transportable tools and
lawn and garden machinery - Safety - Part 2-1: Particular
requirements for hand-held drills and impact drills
(IEC 62841-2-1:2017 , modified)
Outils électroportatifs à moteur, outils portables et machines Elektrische Motorbetriebene handgeführte Werkzeuge,
pour jardins et pelouses - Sécurité - Partie 2-1: Exigences transportable Werkzeuge und Rasen- und
particulières pour les perceuses portatives et les perceuses Gartenmaschinen - Sicherheit - Teil 2-1: Besondere
à percussion Anforderungen für handgeführte Bohrmaschinen und
(IEC 62841-2-1:2017 , modifiée) Schlagbohrmaschinen
(IEC 62841-2-1:2017 , modifiziert)
This European Standard was approved by CENELEC on 2017-05-15. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden,
Switzerland, Turkey and the United Kingdom.
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2018 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN 62841-2-1:2018 E
---------------------- Page: 3 ----------------------
SIST EN 62841-2-1:2018
EN 62841-2-1:2018
European foreword
The text of document 116/321/FDIS, future edition 1 of IEC 62841-2-1, prepared by IEC/TC 116 "Safety
of motor-operated electric tools" was submitted to the IEC-CENELEC parallel vote and approved by
CENELEC as EN 62841-2-1:2018.
A draft amendment, which covers common modifications to IEC 62841-2-1 (116/321/FDIS), was prepared
by CLC/TC 116 "Safety of motor-operated electric tools" and approved by CENELEC.
The following dates are fixed:
• latest date by which this document has to be implemented (dop) 2018-07-19
at national level by publication of an identical
national standard or by endorsement
(dow) 2022-01-19
• latest date by which the national standards conflicting
with this document have to be withdrawn
This document supersedes EN 60745-2-1:2010.
This European Standard is divided into four parts:
Part 1: General requirements which are common to most hand-held electric motor operated tools
(for the purpose of this standard referred to simply as tools) which could come within the
scope of this standard;
Part 2, 3 or 4: Requirements for particular types of tools which either supplement or modify the
requirements given in Part 1 to account for the particular hazards and characteristics of
these specific tools.
This Part 2-1 is to be used in conjunction with EN 62841-1:2015.
This Part 2-1 supplements or modifies the corresponding clauses in EN 62841-1:2015, so as to convert it
into the European Standard: Particular requirements for hand-held drills and impact drills.
Where a particular subclause of Part 1 is not
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.