EN 61753-111-7:2010

Fibre optic interconnecting devices and passive components - Performance standard - Part 111-7: Sealed closures for category A - Aerial

IEC 61753-111-7:2009 contains the minimum test and measurement requirements and severities which a sealed fibre optic closure must satisfy in order to be categorised as meeting the IEC standard for category A - aerial, as defined in Annex A of IEC 61753-1. Free breathing closures are not covered in this standard.

Lichtwellenleiter - Verbindungselemente und passive Bauteile - Betriebsverhalten - Teil 111-7: Druckdichte Muffen für die Kategorie A - oberirdische Verlegung

Dispositifs d'interconnexion et composants passifs à fibres optiques - Norme de qualité de fonctionnement - Partie 111-7: Boîtiers scellés pour catégorie A - Aériens

La CEI 61753-111-7:2009 contient les sévérités et les exigences minimales d'essai et de mesure auxquelles un boîtier à fibres optiques scellé doit satisfaire afin d'être classé comme conforme aux exigences de la norme CEI pour la catégorie A - aérien, telle qu'elle est définie à l'Annexe A de la CEI 61753-1. Les boîtiers à ventilation libre ne sont pas couverts par la présente norme.

Optični spojni elementi in pasivne komponente - Izvedbeni standard - 111-7. del: Zatesnjene spojnice za kategorijo A (Aerial) - Nadzemna uporaba (IEC 61753-111-7:2009)

Ta del IEC 61753 vsebuje minimalne zahteve za preskus in merjenje ter natančnost, ki jih mora izpolnjevati zatesnjena optična spojnica, da zadošča standardu IEC za kategorijo A (Aerial) – Nadzemna uporaba, kot je opredeljeno v Dodatku A IEC 61753-1. Ta standard ne zajema spojnic z zračenjem.

General Information

• Status: Withdrawn
• Publication Date: 18-Feb-2010
• Withdrawal Date: 31-Jan-2013
• ICS: 33.180.20 - Fibre optic interconnecting devices
• Technical Committee: CLC/TC 86BXA - Fibre optic interconnect, passive and connectorised components
• Drafting Committee: IEC/SC 86B - IEC_SC_86B
• Parallel Committee: IEC/SC 86B - IEC_SC_86B
• Current Stage: 9960 - Withdrawal effective - Withdrawal
• Start Date: 08-Oct-2022
• Completion Date: 08-Oct-2022
• Ref Project: SIST EN 61753-111-7:2010 - Fibre optic interconnecting devices and passive components - Performance standard - Part 111-7: Sealed closures for category A - Aerial (IEC 61753-111-7:2009)

Relations

• Replaced By: EN IEC 61753-111-07:2021 - Fibre optic interconnecting devices and passive components - Performance standard - Part 111-07: Sealed closures - Category A - Aerial
• Effective Date: 23-Jan-2023

Standards Content (Sample)

SLOVENSKI STANDARD
01-april-2010
2SWLþQLVSRMQLHOHPHQWLLQSDVLYQHNRPSRQHQWH,]YHGEHQLVWDQGDUGGHO
=DWHVQMHQHVSRMQLFH]DNDWHJRULMR$$HULDO1DG]HPQDXSRUDED,(&

Fibre optic interconnecting devices and passive components - Performance standard -
Part 111-7: Sealed closures for category A - Aerial (IEC 61753-111-7:2009)
Lichtwellenleiter - Verbindungselemente und passive Bauteile - Betriebsverhalten - Teil
111-7: Druckdichte Muffen für die Kategorie A - oberirdische Verlegung (IEC 61753-111-
7:2009)
Dispositifs d'interconnexion et composants passifs à fibres optiques norme de qualité de
fonctionnement - Partie 111-7: Boîtiers scellés pour catégorie A - Aériens (CEI 61753-
111-7:2009)
Ta slovenski standard je istoveten z: EN 61753-111-7:2010
ICS:
33.180.20 3RYH]RYDOQHQDSUDYH]D Fibre optic interconnecting
RSWLþQDYODNQD devices
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN 61753-111-7
NORME EUROPÉENNE
February 2010
EUROPÄISCHE NORM
ICS 33.180.20
English version
Fibre optic interconnecting devices
and passive components performance standard -
Part 111-7: Sealed closures for category A -
Aerial
(IEC 61753-111-7:2009)
Dispositifs d'interconnexion et composants Lichtwellenleiter -
passifs à fibres optiques norme Verbindungselemente und passive
de qualité de fonctionnement - Bauteile -
Partie 111-7: Boîtiers scellés Betriebsverhalten -
pour catégorie A - Teil 111-7: Druckdichte Muffen
Aériens für die Kategorie A -
(CEI 61753-111-7:2009) oberirdische Verlegung
(IEC 61753-111-7:2009)
This European Standard was approved by CENELEC on 2010-02-01. CENELEC members are bound to comply
with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard
the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the Central Secretariat or to any CENELEC member.

This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and notified
to the Central Secretariat has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus,
the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy,
Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia,
Spain, Sweden, Switzerland and the United Kingdom.

CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung

CEN-CENELEC Management Centre: Avenue Marnix 17, B - 1000 Brussels

© 2010 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 61753-111-7:2010 E

Foreword
The text of document 86B/2904/FDIS, future edition 1 of IEC 61753-111-7, prepared by SC 86B, Fibre
optic interconnecting devices and passive components, of IEC TC 86, Fibre optics, was submitted to the
IEC-CENELEC parallel vote and was approved by CENELEC as EN 61753-111-7 on 2010-02-01.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN and CENELEC shall not be held responsible for identifying any or all such patent
rights.
The following dates were fixed:
– latest date by which the EN has to be implemented
at national level by publication of an identical
(dop) 2010-11-01
national standard or by endorsement
– latest date by which the national standards conflicting
(dow) 2013-02-01
with the EN have to be withdrawn
Annex ZA has been added by CENELEC.
__________
Endorsement notice
The text of the International Standard IEC 61753-111-7:2009 was approved by CENELEC as a European
Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standards indicated:
IEC 60068-1 NOTE  Harmonized as EN 60068-1.
IEC 60068-2 NOTE  Harmonized in EN 60068-2 series (not modified).
IEC 60721-3-1 NOTE  Harmonized as EN 60721-3-1.
IEC 60793-2 NOTE  Harmonized as EN 60793-2.
IEC 60794-1-2 NOTE  Harmonized as EN 60794-1-2.
IEC 60794-2 NOTE  Harmonized as EN 60794-2.
IEC 60794-3 NOTE  Harmonized as EN 60794-3.
IEC 61300 NOTE  Harmonized in EN 61300 series (not modified).
IEC 62005 NOTE  Harmonized in EN 62005 series (not modified).
__________
- 3 - EN 61753-111-7:2010
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications

The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.

NOTE  When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD
applies.
Publication Year Title EN/HD Year

IEC 60068-2-10 - Environmental testing - EN 60068-2-10 -
Part 2-10: Tests - Test J and guidance:
Mould growth
IEC 60721-3-2 - Classification of environmental conditions - EN 60721-3-2 -
Part 3: Classification of groups of
environmental parameters
and their severities - Section 2: Transportation

IEC 60793-2-50 2008 Optical fibres - EN 60793-2-50 2008
Part 2-50: Product specifications - Sectional
specification for class B single-mode fibres

IEC 61300-1 - Fibre optic interconnecting devices and EN 61300-1 -
passive components - Basic test and
measurement procedures -
Part 1: General and guidance
IEC 61300-2-1 - Fibre optic interconnecting devices and EN 61300-2-1 -
passive components - Basic test and
measurement procedures -
Part 2-1: Tests - Vibration (sinusoidal)

IEC 61300-2-4 - Fibre optic interconnecting devices and EN 61300-2-4 -
passive components - Basic test and
measurement procedures -
Part 2-4: Tests - Fibre/cable retention

IEC 61300-2-5 - Fibre optic interconnecting devices and EN 61300-2-5 -
passive components - Basic test and
measurement procedures -
Part 2-5: Tests - Torsion
IEC 61300-2-9 - Fibre optic interconnecting devices and EN 61300-2-9 -
passive components - Basic test and
measurement procedures -
Part 2-9: Tests - Shock
IEC 61300-2-11 - Fibre optic interconnecting devices and EN 61300-2-11 -
passive components - Basic test and
measurement procedures -
Part 2-11: Tests - Axial compression

IEC 61300-2-12 2009 Fibre optic interconnecting devices and EN 61300-2-12 2009
passive components - Basic test and
measurement procedures -
Part 2-12: Tests - Impact
IEC 61300-2-22 - Fibre optic interconnecting devices and EN 61300-2-22 -
passive components - Basic test and
measurement procedures -
Part 2-22: Tests - Change of temperature

Publication Year Title EN/HD Year

IEC 61300-2-26 - Fibre optic interconnecting devices and EN 61300-2-26 -
passive components - Basic test and
measurement procedures -
Part 2-26: Tests - Salt mist
IEC 61300-2-33 - Fibre optic interconnecting devices and EN 61300-2-33 -
passive components - Basic test and
measurement procedures -
Part 2-33: Tests - Assembly and disassembly
of fibre optic closures
IEC 61300-2-37 - Fibre optic interconnecting devices and EN 61300-2-37 -
passive components - Basic test and
measurement procedures -
Part 2-37: Tests - Cable bending for fibre optic
closures
IEC 61300-2-38 2006 Fibre optic interconnecting devices and EN 61300-2-38 2006
passive components - Basic test and
measurement procedures -
Part 2-38: Tests - Sealing for pressurized fibre
optic closures
IEC 61300-3-1 - Fibre optic interconnecting devices and EN 61300-3-1 -
passive components - Basic test and
measurement procedures -
Part 3-1: Examinations and measurements -
Visual examination
IEC 61300-3-3 2009 Fibre optic interconnecting devices and EN 61300-3-3 2009
passive components - Basic test and
measurement procedures -
Part 3-3: Examinations and measurements -
Active monitoring of changes in attenuation
and return loss
IEC 61300-3-28 - Fibre optic interconnecting devices and EN 61300-3-28 -
passive components - Basic test and
measurement procedures -
Part 3-28: Examinations and measurements -
Transient loss
IEC 61753-1 2007 Fibre optic interconnecting devices and EN 61753-1 2007
passive components performance standard -
Part 1: General and guidance for performance
standards
IEC 62134-1 - Fibre optic interconnecting devices and EN 62134-1 -
passive components - Fibre optic closures -
Part 1: Generic specification
ISO 4892-3 2006 Plastics - Methods of exposure to laboratory EN ISO 4892-3 2006
light sources -
Part 3: Fluorescent UV lamps
IEC 61753-111-7 ®
Edition 1.0 2009-11
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Fibre optic interconnecting devices and passive components performance
standard –
Part 111-7: Sealed closures for category A – Aerial

Dispositifs d'interconnexion et composants passifs à fibres optiques norme de
qualité de fonctionnement –
Partie 111-7: Boîtiers scellés pour catégorie A – Aériens

INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
PRICE CODE
INTERNATIONALE
T
CODE PRIX
ICS 33.180.20 ISBN 2-8318-1067-3
– 2 – 61753-111-7 © IEC:2009
CONTENTS
FOREWORD.3
INTRODUCTION.5
1 Scope.6
2 Normative references.6
3 Terms, definitions and abbreviations .7
3.1 Terms and definitions .7
3.2 Abbreviations.8
4 General requirements .9
4.1 Storage, transportation and packaging .9
4.2 Marking and identification .9
4.3 Materials .9
4.4 Closure overpressure safety .10
4.5 Test report.10
5 Test.10
5.1 General .10
5.2 Test specimen preparation.10
5.3 Test and measurement methods .11
5.4 Installation or intervention.11
5.5 Pass/fail criteria.11
6 Performance requirements.12
6.1 Sample size.12
6.2 Sealing, optical and appearance performance criteria .12
6.3 Mechanical sealing performance requirements.13
6.4 Environmental sealing performance requirements .15
6.5 Mechanical optical performance requirements.15
6.6 Environmental optical performance requirements .17
Annex A (normative) Sample definition .18
Annex B (normative) Sample size.20
Annex C (normative) Intervention and reconfiguration/resplicing .21
Bibliography .23

Figure A.1 – Track joint configuration sample .18
Figure A.2 – Distribution joint configuration sample.19

Table 1 – Tightness, optical and appearance performance criteria .12
Table 2 – Mechanical sealing performance requirements .13
Table 3 – Environmental sealing performance requirements .15
Table 4 – Mechanical optical performance requirements.
...