Connectors for electrical and electronic equipment - Tests and measurements - Part 27-200: Additional specifications for signal integrity tests up to 2 000 MHz on IEC 60603-7 series connectors - Tests 27a to 27g

IEC 60512-27-200:2022 is primarily intended for use in signal integrity and transmission performance testing up to 2 000 MHz of IEC 60603-7 series 8-way connector type IEC 60603‑7‑81, according to connector test method IEC 60512‑28‑100. This part of IEC 60512 covers additional, supplemental test method specifications to extend the upper frequency for the test connectors and associated indirect-reference test fixtures used in the signal integrity and transmission performance tests specified in IEC 60512‑27‑100. In support of de-embedded crosstalk and related transmission requirements specified in IEC 60603‑7‑81, for frequencies up to 2 000 MHz, these supplemental specifications extend the upper test frequency from IEC 60512‑27‑100 up to 500 MHz to the upper test frequency of IEC 60512‑28‑100 up to 2 000 MHz. This document covers measurements of connector signal integrity and transmission performance of 8-way connector types defined in these published connector series standards: - IEC 60603‑7‑2 - IEC 60603‑7‑3 - IEC 60603‑7‑4 - IEC 60603‑7‑5 - IEC 60603‑7‑41 - IEC 60603‑7‑51 - IEC 60603‑7‑81. This document covers respective performance test procedures of connector signal integrity and transmission performance defined in these published connector test method series standards: - IEC 60512‑26‑100 - IEC 60512‑27‑100 - IEC 60512‑28‑100.

Steckverbinder für elektrische und elektronische Einrichtungen - Mess- und Prüfverfahren - Teil 27-200: Zusätzliche Festlegungen für Signalintegritätsprüfungen bis 2 000 MHz bei Steckverbindern der Reihe IEC 60603-7 - Prüfungen 27a bis 27g

Connecteurs pour équipements électriques et électroniques - Essais et mesures - Partie 27-200: Spécifications supplémentaires pour les essais d’intégrité des signaux jusqu’à 2 000 MHz sur les connecteurs de la série IEC 60603-7 - Essais 27a à 27g

L'IEC 60512-27-200:2022 est avant tout destiné à être utilisé pour les essais d’intégrité des signaux et de qualité de la transmission jusqu’à 2 000 MHz des types de connecteurs à 8 voies couverts par la série IEC 60603-7 (IEC 60603‑7‑81), conformément à la méthode d’essai des connecteurs de l’IEC 60512‑28‑100. Le présent document couvre les connecteurs d’essai ainsi que les dispositifs d’essai à référence indirecte utilisés pour mesurer l’intégrité des signaux et la qualité de la transmission selon les exigences de la série IEC 60603-7 concernant les types de connecteurs à 8 voies définis dans les normes publiées suivantes: - IEC 60603‑7‑2 - IEC 60603‑7‑3 - IEC 60603‑7‑4 - IEC 60603‑7‑5 - IEC 60603‑7‑41 - IEC 60603‑7‑51 - IEC 60603‑7‑81 Le présent document fournit des informations supplémentaires sur les connecteurs d’essai ainsi que sur les dispositifs d’essai utilisés pour les mesures de performance des connecteurs conformément aux normes de méthode d’essai qui concernent ces connecteurs: - IEC 60512‑26‑100 - IEC 60512‑27‑100 - IEC 60512‑28‑100

Konektorji za električno in elektronsko opremo - Preskusi in meritve - 27-200. del: Dodatne specifikacije za preskuse signalne celovitosti do 2000 MHz na konektorjih serije IEC 60603-7 - Preskusi od 27a do 27g (IEC 60512-27-200:2022)

General Information

Status
Published
Publication Date
20-Oct-2022
Technical Committee
Drafting Committee
Current Stage
6060 - Document made available - Publishing
Start Date
21-Oct-2022
Completion Date
21-Oct-2022

Buy Standard

Standard
EN IEC 60512-27-200:2022 - BARVE
English language
32 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI STANDARD
01-december-2022
Konektorji za električno in elektronsko opremo - Preskusi in meritve - 27-200. del:
Dodatne specifikacije za preskuse signalne celovitosti do 2000 MHz na konektorjih
serije IEC 60603-7 - Preskusi od 27a do 27g (IEC 60512-27-200:2022)
Connectors for electrical and electronic equipment - Tests and measurements - Part 27-
200: Additional specifications for signal integrity tests up to 2 000 MHz on IEC 60603-7
series connectors - Tests 27a to 27g (IEC 60512-27-200:2022)
Steckverbinder für elektrische und elektronische Einrichtungen – Mess- und
Prüfverfahren – Teil 27-200: Zusätzliche Festlegungen für Signalintegritätsprüfungen bis
2 000 MHz bei Steckverbindern der Reihe IEC 60603-7 – Prüfungen 27a bis 27g (IEC
60512-27-200:2022)
Connecteurs pour équipements électriques et électroniques - Essais et mesures - Partie
27-200: Spécifications supplémentaires pour les essais d’intégrité des signaux jusqu’à 2
000 MHz sur les connecteurs de la série IEC 60603-7 - Essais 27a à 27g (IEC 60512-27
-200:2022)
Ta slovenski standard je istoveten z: EN IEC 60512-27-200:2022
ICS:
31.220.10 Vtiči in vtičnice, konektorji Plug-and-socket devices.
Connectors
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD EN IEC 60512-27-200

NORME EUROPÉENNE
EUROPÄISCHE NORM October 2022
ICS 31.220.10
English Version
Connectors for electrical and electronic equipment - Tests and
measurements - Part 27-200: Additional specifications for signal
integrity tests up to 2 000 MHz on IEC 60603-7 series
connectors - Tests 27a to 27g
(IEC 60512-27-200:2022)
Connecteurs pour équipements électriques et électroniques Steckverbinder für elektrische und elektronische
- Essais et mesures - Partie 27-200: Spécifications Einrichtungen - Mess- und Prüfverfahren - Teil 27-200:
supplémentaires pour les essais d'intégrité des signaux Zusätzliche Festlegungen für Signalintegritätsprüfungen bis
jusqu'à 2 000 MHz sur les connecteurs de la série IEC 2 000 MHz bei Steckverbindern der Reihe IEC 60603-7 -
60603-7 - Essais 27a à 27g Prüfungen 27a bis 27g
(IEC 60512-27-200:2022) (IEC 60512-27-200:2022)
This European Standard was approved by CENELEC on 2022-10-20. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Türkiye and the United Kingdom.

European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2022 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 60512-27-200:2022 E

European foreword
The text of document 48B/2976/FDIS, future edition 1 of IEC 60512-27-200, prepared by SC 48B
"Electrical connectors" of IEC/TC 48 "Electrical connectors and mechanical structures for electrical
and electronic equipment" was submitted to the IEC-CENELEC parallel vote and approved by
CENELEC as EN IEC 60512-27-200:2022.
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2023-07-20
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2025-10-20
document have to be withdrawn
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
Any feedback and questions on this document should be directed to the users’ national committee. A
complete listing of these bodies can be found on the CENELEC website.
Endorsement notice
The text of the International Standard IEC 60512-27-200:2022 was approved by CENELEC as a
European Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standard indicated:
IEC 60603-7-7 NOTE Harmonized as EN 60603-7-7
IEC 60603-7-71 NOTE Harmonized as EN 60603-7-71
IEC 60603-7-82 NOTE Harmonized as EN 60603-7-82
IEC 61076-3-110 NOTE Harmonized as EN 61076-3-110
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1 Where an International Publication has been modified by common modifications, indicated by (mod), the
relevant EN/HD applies.
NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available
here: www.cenelec.eu.
Publication Year Title EN/HD Year
IEC 60050-581 - International Electrotechnical Vocabulary - - -
Part 581: Electromechanical components
for electronic equipment
IEC 60512-1 - Connectors for electrical and electronic EN IEC 60512-1 -
equipment - Tests and measurements -
Part 1: Generic specification
IEC 60512-26-100 - Connectors for electronic equipment - EN 60512-26-100 -
Tests and measurements - Part 26-100:
Measurement setup, test and reference
arrangements and measurements for
connectors according to IEC 60603-7 -
Tests 26a to 26g
IEC 60512-27-100 - Connectors for electronic equipment - EN 60512-27-100 -
Tests and measurements - Part 27-100:
Signal integrity tests up to 500 MHz on
IEC 60603-7 series connectors - Tests 27a
to 27g
IEC 60512-28-100 - Connectors for electrical and electronic EN IEC 60512-28-100 -
equipment - Tests and measurements -
Part 28-100: Signal integrity tests up to
2 000 MHz - Tests 28a to 28g
IEC 60603-7 - Connectors for electronic equipment - Part EN IEC 60603-7 -
7: Detail specification for 8-way,
unshielded, free and fixed connectors
IEC 60603-7-1 - Connectors for electronic equipment - Part EN 60603-7-1 -
7-1: Detail specification for 8-way,
shielded, free and fixed connectors
IEC 60603-7-2 - Connectors for electronic equipment - Part EN 60603-7-2 -
7-2: Detail specification for 8-way,
unshielded, free and fixed connectors, for
data transmissions with frequencies up to
100 MHz
IEC 60603-7-3 - Connectors for electronic equipment - Part EN 60603-7-3 -
7-3: Detail specification for 8-way,
shielded, free and fixed connectors, for
data transmission with frequencies up to
100 MHz
IEC 60603-7-4 - Connectors for electronic equipment - Part EN 60603-7-4 -
7-4: Detail specification for 8-way,
unshielded, free and fixed connectors, for
data transmissions with frequencies up to
250 MHz
IEC 60603-7-5 - Connectors for electronic equipment - Part EN 60603-7-5 -
7-5: Detail specification for 8-way,
shielded, free and fixed connectors, for
data transmissions with frequencies up to
250 MHz
IEC 60603-7-41 - Connectors for electronic equipment - Part EN 60603-7-41 -
7-41: Detail specification for 8-way,
unshielded, free and fixed connectors, for
data transmissions with frequencies up to
500 MHz
IEC 60603-7-51 - Connectors for electronic equipment - Part EN 60603-7-51 -
7-51: Detail specification for 8-way,
shielded, free and fixed connectors, for
data transmissions with frequencies up to
500 MHz
IEC 60603-7-81 - Connectors for electronic equipment - Part EN 60603-7-81 -
7-81: Detail specification for 8-way,
shielded, free and fixed connectors, for
data transmissions with frequencies up to
2 000 MHz
IEC 61156-1 - Multicore and symmetrical pair/quad - -
cables for digital communications - Part 1:
Generic specification
IEC 61156-9 - Multicore and symmetrical pair/quad - -
cables for digital communications - Part 9:
Cables for channels with transmission
characteristics up to 2 GHz - Sectional
specification
IEC 61156-10 - Multicore and symmetrical pair/quad - -
cables for digital communications - Part 10:
Cables for cords with transmission
characteristics up to 2 GHz - Sectional
specification
IEC 61935-2 - Specification for the testing of balanced EN 61935-2 -
and coaxial information technology cabling
- Part 2: Cords as specified in
ISO/IEC 11801-1 and related standards
IEC 62153-4-12 - Metallic communication cable test methods - -
- Part 4-12: Electromagnetic compatibility
(EMC) - Coupling attenuation or screening
attenuation of connecting hardware -
Absorbing clamp method
IEC 60512-27-200 ®
Edition 1.0 2022-09
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
colour
inside
Connectors for electrical and electronic equipment – Tests and measurements –
Part 27-200: Additional specifications for signal integrity tests up to 2 000 MHz
on IEC 60603-7 series connectors – Tests 27a to 27g
Connecteurs pour équipements électriques et électroniques – Essais et
mesures –
Partie 27-200: Spécifications supplémentaires pour les essais d’intégrité des
signaux jusqu’à 2 000 MHz sur les connecteurs de la série IEC 60603-7 –
Essais 27a à 27g
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 31.220.10 ISBN 978-2-8322-5666-4
– 2 – IEC 60512-27-200:2022 © IEC 2022
CONTENTS
FOREWORD . 4
INTRODUCTION . 6
1 Scope . 7
2 Normative references . 8
3 Terms and definitions . 9
4 Test connector specifications. 9
4.1 General . 9
4.2 Indirect-reference test fixtures . 10
4.3 Category 8.1 test plug requirements . 11
4.3.1 General . 11
4.3.2 Category 8.1 test plug NEXT loss requirements . 11
4.3.3 Category 8.1 test plug return loss requirements . 11
4.4 Category 8.1 cord test head requirements . 12
4.4.1 General . 12
4.4.2 Category 8.1 cord test head return loss . 12
Annex A (informative) Test connectors specifications. 13
A.1 General . 13
A.2 Test plug specifications. 13
A.2.1 General . 13
A.2.2 Test plug NEXT loss limit vectors . 13
A.2.3 Mated connector NEXT loss specifications . 14
A.2.4 Test plug NEXT loss specifications . 14
A.2.5 Test plug phase reference plane and calibration planes . 16
A.2.6 Device delay measurements . 17
A.3 Cord test head specifications . 19
A.3.1 General . 19
A.3.2 Cord test head NEXT loss, centred . 19
A.3.3 Cord test head FEXT loss . 19
A.3.4 Cord test head return loss . 19
Annex B (informative) Balun measurement procedures use of test plugs and test
heads .
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.