iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CLC

EN 60695-1-10:2017

(Main)

Fire hazard testing - Part 1-10: Guidance for assessing the fire hazard of electrotechnical products - General guidelines

Fire hazard testing - Part 1-10: Guidance for assessing the fire hazard of electrotechnical products - General guidelines

IEC 60695-1-10:2009 provides general guidance on how to reduce to acceptable levels the risk of fire and the potential effects of fires involving electrotechnical products. It also describes the relationship between fire risk and the potential effects of fire, it also emphasises the importance of the scenario approach to fire hazard and risk assessment and discusses criteria intended to ensure the development of technically sound hazard-based fire test methods. It has the status of a basic safety publication in accordance with IEC Guide 104 and ISO/IEC Guide 51.

Prüfungen zur Beurteilung der Brandgefahr - Teil 1-10: Anleitung zur Beurteilung der Brandgefahr von elektrotechnischen Erzeugnissen – Allgemeiner Leitfaden

Essais relatifs aux risques du feu - Partie 1-10: Lignes directrices pour l'évaluation des risques du feu des produits électrotechniques - Lignes directrices générales

La CEI 60695-1-10:2009 fournit des lignes directrices générales sur la manière de réduire à des niveaux acceptables le risque d'incendie et les effets potentiels des incendies impliquant des produits électrotechniques. Elle décrit la relation entre le risque d'incendie et les effets potentiels des incendies. Elle souligne l'importance de l'approche par scénario pour l'évaluation des dangers du feu et des risques d'incendie. Elle débat également des critères visant à assurer le développement de méthodes d'essai au feu basées sur les dangers qui soient techniquement solides. La présente publication fondamentale de sécurité est destinée aux comités d'études dans le cadre de l'élaboration de normes conformes aux principes exposés dans le Guide CEI 104 et le Guide ISO/CEI 51.

Preskušanje požarne ogroženosti - 1-10. del: Navodilo za ocenjevanje požarne varnosti elektrotehniških izdelkov - Splošne smernice (IEC 60695-1-10:2016)

Standard IEC 60695-1-10:2009 podaja splošne smernice za zmanjševanje nevarnosti požara in morebitnih vplivov požarov pri elektrotehniških izdelkih na sprejemljivo raven. Opisuje tudi razmerje med nevarnostjo in morebitnimi vplivi požara, poudarja pomembnost pristopa na temelju predvidenih potekov dogodkov glede nevarnosti požara in ocenjevanja tveganja ter obravnava merila, ki zagotavljajo razvoj tehnično ustreznih metod za preskušanje požarne ogroženosti. Ta standard ima status osnovne varnostne publikacije v skladu z vodili IEC 104 in ISO/IEC 51.

General Information

Status
Published
Publication Date
02-Mar-2017
Withdrawal Date
22-Dec-2019
ICS
13.220.40 - Ignitability and burning behaviour of materials and products
29.020 - Electrical engineering in general
Technical Committee
CLC/SR 89 - Fire hazard testing
Drafting Committee
IEC/TC 89 - IEC_TC_89
Current Stage
6060 - Document made available - Publishing
Start Date
03-Mar-2017
Completion Date
03-Mar-2017
Ref Project
SIST EN 60695-1-10:2017 - Fire hazard testing - Part 1-10: Guidance for assessing the fire hazard of electrotechnical products - General guidelines (IEC 60695-1-10:2016)

Relations

Replaces
EN 60695-1-10:2010 - Fire hazard testing - Part 1-10: Guidance for assessing the fire hazard of electrotechnical products - General guidelines
Effective Date
07-Mar-2017

Buy Standard

EN 60695-1-10:2017EN 60695-1-10:2017
PreviousNext
Standard
EN 60695-1-10:2017
English language
28 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI STANDARD
01-maj-2017
1DGRPHãþD
SIST EN 60695-1-10:2010
Preskušanje požarne ogroženosti - 1-10. del: Navodilo za ocenjevanje požarne
varnosti elektrotehniških izdelkov - Splošne smernice (IEC 60695-1-10:2016)
Fire hazard testing - Part 1-10: Guidance for assessing the fire hazard of electrotechnical
products - General guidelines (IEC 60695-1-10:2016)
Prüfungen zur Beurteilung der Brandgefahr - Teil 1-10: Anleitung zur Beurteilung der
Brandgefahr von elektrotechnischen Erzeugnissen - Allgemeiner Leitfaden (IEC 60695-1
-10:2016)
Essais relatifs aux risques du feu - Partie 1-10: Guide pour l'évaluation des risques du
feu des produits électrotechniques - Lignes directrices générales (IEC 60695-1-10:2016)
Ta slovenski standard je istoveten z: EN 60695-1-10:2017
ICS:
13.220.40 Sposobnost vžiga in Ignitability and burning
obnašanje materialov in behaviour of materials and
proizvodov pri gorenju products
29.020 Elektrotehnika na splošno Electrical engineering in
general
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD EN 60695-1-10

NORME EUROPÉENNE
EUROPÄISCHE NORM
March 2017
ICS 13.220.40; 29.020 Supersedes EN 60695-1-10:2010
English Version
Fire hazard testing - Part 1-10: Guidance for assessing the fire
hazard of electrotechnical products - General guidelines
(IEC 60695-1-10:2016)
Essais relatifs aux risques du feu - Partie 1-10: Lignes Prüfungen zur Beurteilung der Brandgefahr -
directrices pour l'évaluation des risques du feu des produits Teil 1-10: Anleitung zur Beurteilung der Brandgefahr von
électrotechniques - Lignes directrices générales elektrotechnischen Erzeugnissen - Allgemeiner Leitfaden
(IEC 60695-1-10:2016) (IEC 60695-1-10:2016)
This European Standard was approved by CENELEC on 2016-12-23. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden,
Switzerland, Turkey and the United Kingdom.

European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2017 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN 60695-1-10:2017 E
European foreword
The text of document 89/1341/FDIS, future edition 2 of IEC 60695-1-10, prepared by IEC/TC 89 "Fire
hazard testing" was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as
The following dates are fixed:
(dop) 2017-09-23
• latest date by which the document has to be implemented at
national level by publication of an identical national
standard or by endorsement
(dow) 2019-12-23
• latest date by which the national standards conflicting with
the document have to be withdrawn

This document supersedes EN 60695-1-10:2010.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such
patent rights.
Endorsement notice
The text of the International Standard IEC 60695-1-10:2016 was approved by CENELEC as a
European Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standards indicated:
IEC 60950-1 NOTE Harmonized as EN 60950-1.
IEC 60065 NOTE Harmonized as EN 60065.
IEC 60332-1-2 NOTE Harmonized as EN 60332-1-2.
IEC 62368-1 NOTE Harmonized as EN 62368-1.
IEC 60695-1 NOTE Harmonized in EN 60695-1 series.
IEC 60695-2 NOTE Harmonized in EN 60695-2 series.
IEC 60695-5 NOTE Harmonized in EN 60695-5 series.
IEC 60695-6 NOTE Harmonized in EN 60695-6 series.
IEC 60695-7 NOTE Harmonized in EN 60695-7 series.
IEC 60695-8 NOTE Harmonized in EN 60695-8 series.
IEC 60695-9 NOTE Harmonized in EN 60695-9 series.
IEC 60695-10 NOTE Harmonized in EN 60695-10 series.
IEC 60695-11 NOTE Harmonized in EN 60695-11 series.
IEC 60695-1-20 NOTE Harmonized as EN 60695-1-20.
IEC/TS 62441 NOTE Harmonized as CLC/TS 62441.
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.
NOTE 1 When an International Publication has been modified by common modifications, indicated by (mod),
the relevant EN/HD applies.
NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is
available here: www.cenelec.eu.

Publication Year Title EN/HD Year
IEC 60079-0 -  Explosive atmospheres - Part 0: EN 60079-0 -
Equipment - General requirements
IEC 60695-1-11 -  Fire hazard testing - Part 1-11: EN 60695-1-11 -
Guidance for assessing the fire hazard
of electrotechnical products - Fire
hazard assessment
IEC 60695-1-12 -  Fire hazard testing - Part 1-12: - -
Guidance for assessing the fire hazard
of electrotechnical products - Fire safety
engineering
IEC 60695-1-30 -  Fire hazard testing - Part 1-30: EN 60695-1-30 -
Guidance for assessing the fire hazard
of electrotechnical products -
Preselection testing process - General
guidelines
IEC 60695-4 2012 Fire hazard testing - Part 4: Terminology EN 60695-4 2012
concerning fire tests for electrotechnical
products
IEC Guide 104 -  The preparation of safety publications - -
and the use of basic safety publications
and group safety publications
ISO/IEC Guide 51 -  Safety aspects - Guidelines for their - -
inclusion in standards
ISO 13943 2008 Fire safety - Vocabulary EN ISO 13943 2010

IEC 60695-1-10 ®
Edition 2.0 2016-11
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
BASIC SAFETY PUBLICATION
PUBLICATION FONDAMENTALE DE SÉCURITÉ

Fire hazard testing –
Part 1-10: Guidance for assessing the fire hazard of electrotechnical products –

General guidelines
Essais relatifs aux risques du feu –

Partie 1-10: Lignes directrices pour l'évaluation des risques du feu des produits

électrotechniques – Lignes directrices générales

INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 13.220.40; 29.020 ISBN 978-2-8322-3755-7

– 2 – IEC 60695-1-10:2016  IEC 2016
CONTENTS
FOREWORD . 3
INTRODUCTION . 5
1 Scope . 6
2 Normative references . 6
3 Terms and definitions . 7
4 Fire hazards associated with electrotechnical products . 9
5 Fundamentals of fire hazard testing . 10
5.1 Objectives . 10
5.2 Fire hazard and fire risk . 10
5.2.1 Fire hazard . 10
5.2.2 Fire risk . 12
5.3 Fire scenarios . 13
5.4 Fire-safety engineering . 15
5.5 Fire hazard assessment . 15
6 Types of fire test . 15
6.1 General . 15
6.2 Quantitative and qualitative groups of fire tests . 15
6.2.1 Quantitative fire tests . 15
6.2.2 Qualitative fire tests . 16
6.3 Types of fire tests . 16
6.3.1 Fire simulation test . 16
6.3.2 Fire resistance tests . 16
6.3.3 Tests with regard to reaction to fire . 16
6.3.4 Preselection fire tests . 16
6.3.5 Basic property tests . 17
7 Appropriate use of qualitative fire tests . 17
8 Preparation of requirements and test specifications . 17
9 Common ignition sources . 18
10 Reference documents of TC 89 . 18
Annex A (informative) The power output of ignition sources . 19
A.1 General . 19
A.2 Some common electrical and non-electrical ignition sources . 19
A.3 Power source classification in IEC 62368-1 [9] . 20
Annex B (informative) Guidance publications and test methods . 21
Bibliography . 23

Table 1 – Common causes of ignition encountered in electrotechnical products . 11
Table 2 – Characteristics of fire stages (from Table 1 in ISO 19706:2011 [22]) . 14
Table A.1 – Examples of ignition sources . 20
Table B.1 – TC 89 guidance publications and test methods . 21

IEC 60695-1-10:2016  IEC 2016 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
FIRE HAZARD TESTING –
Part 1-10: Guidance for assessing the fire hazard of
electrotechnical products – General guidelines

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CLC
EN IEC 60695-2-10:2021/AC:2024-01(Corrigendum)
Fire hazard testing - Part 2-10: Glowing/hot-wire based test methods - Glow-wire apparatus and common test procedure
SIST EN IEC 60695-2-10:2022/AC:2024
  • Corrigendum
    4 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 60695-7-2:2021(Main)
Fire hazard testing - Part 7-2: Toxicity of fire effluent - Summary and relevance of test methods
SIST EN IEC 60695-7-2:2022

IEC 60695-7-2:2021 gives a brief summary of the test methods that are in common use in the assessment of the toxicity of fire effluent. It includes special observations on their relevance to real fire scenarios and gives recommendations on their use. It advises which tests provide toxic potency data that are relevant to real fire scenarios, and which are suitable for use in fire hazard assessment and fire safety engineering. The list of test methods is not to be considered exhaustive. This summary cannot be used in place of published standards which are the only valid reference documents. This basic safety publication is intended for use by technical committees in the preparation of standards in accordance with the principles laid down in IEC Guide 104 and ISO/IEC Guide 51. One of the responsibilities of a technical committee is, wherever applicable, to make use of basic safety publications in the preparation of its publications. The requirements, test methods or test conditions of this basic safety publication will not apply unless specifically referred to or included in the relevant publications. This second edition cancels and replaces the first edition published in 2011. This edition constitutes a technical revision. The main changes with respect to the previous edition are listed below: – New text in the introduction; – New text in the scope; – Clause 2 has been updated; – Many terms and definitions in Clause 3 reproduced from ISO 13943 have been deleted. Other terms and definitions have been added. – New text in Subclauses 4.3 and 4.4; – New text in Subclause 6.1; – References to IEC 60695-7-50 and -51 (now withdrawn) have been removed; – Reference to DEF STAN 07-247 has been added; – Details of ISO/TS 19021 have been added; – Details of EN 17084 have been added; – New text added concerning ISO/TS 19700; – New text added concerning the IMO FTP toxicity test; – New Subclause 7.1 has been added; – The Annex in Edition1 has been replaced by new Clause 8; – The bibliography has been updated.

  • Standard
    47 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 60695-2-10:2021(Main)
Fire hazard testing - Part 2-10: Glowing/hot-wire based test methods - Glow-wire apparatus and common test procedure
SIST EN IEC 60695-2-10:2022

This part of IEC 60695 specifies the glow-wire apparatus and common test procedure to simulate the effects of thermal stresses which may be produced by heat sources such as glowing elements or overloaded resistors, for short periods, in order to assess the fire hazard by a simulation technique. The test procedure described in this document is a common test procedure intended for the small-scale tests in which a standardized electrically heated wire is used as a source of ignition. It is a common part of the test procedures applied to end products and to solid electrical insulating materials or other solid combustible materials. A detailed description of each particular test procedure is given in IEC 60695-2-11, IEC 60695-2-12 and IEC 60695-2-13. This basic safety publication focusing on safety test method(s) is primarily intended for use by technical committees in the preparation of safety publications in accordance with the principles laid down in IEC Guide 104 and ISO/IEC Guide 51. One of the responsibilities of a technical committee is, wherever applicable, to make use of basic safety publications in the preparation of its publications.

  • Standard
    26 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 60695-2-11:2021(Main)
Fire hazard testing - Part 2-11: Glowing/hot-wire based test methods - Glow-wire flammability test method for end products (GWEPT)
SIST EN IEC 60695-2-11:2022

This part of IEC 60695 specifies a test method on an end product. It is intended to simulate the effects of thermal stresses produced by an electrically heated source to represent a fire hazard. This test method is used to check that, under defined test conditions, an end product exposed to an electrically heated source has either a limited ability to ignite or, if it ignites, a limited ability to propagate flame. However, the fire hazard analysis, the flammability aspects and the flame spreading to other products are not covered by this document. This basic safety publication focusing on safety test method(s) is primarily intended for use by technical committees in the preparation of safety publications in accordance with the principles laid down in IEC Guide 104 and ISO/IEC Guide 51. One of the responsibilities of a technical committee is, wherever applicable, to make use of basic safety publications in the preparation of its publications.

  • Standard
    19 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 60695-2-12:2021(Main)
Fire hazard testing - Part 2-12: Glowing/hot-wire based test methods - Glow-wire flammability index (GWFI) test method for materials
SIST EN IEC 60695-2-12:2022

This part of IEC 60695 specifies the details of the glow-wire test to be applied to test specimens of solid electrical insulating materials or other solid materials for flammability testing to determine the glow-wire flammability index (GWFI). GWFI is the highest temperature, determined during this standardized procedure, at which the tested material does not ignite or, if it does, extinguishes within 30 s after removal of the glow-wire and is not totally consumed; and molten drips, if they occur, do not ignite the wrapping tissue. This test method is a materials test carried out on a series of standard test specimens. The data obtained, along with data from the glow-wire ignition temperature (GWIT) test method for materials, IEC 60695-2-13, can then be used in a preselection process in accordance with IEC 60695-1-30 [4] to judge the ability of materials to meet the requirements of IEC 60695-2-11. NOTE As an outcome of conducting a fire hazard assessment, an appropriate series of preselection flammability and ignition tests can allow a reduction of end product testing. This basic safety publication focusing on safety test method(s) is primarily intended for use by technical committees in the preparation of safety publications in accordance with the principles laid down in IEC Guide 104 and ISO/IEC Guide 51. One of the responsibilities of a technical committee is, wherever applicable, to make use of basic safety publications in the preparation of its publications.

  • Standard
    16 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 60695-9-2:2021(Main)
Fire hazard testing - Part 9-2: Surface spread of flame - Summary and relevance of test methods
SIST EN IEC 60695-9-2:2021

IEC 60695-9-2:2021 presents a summary of published test methods that are used to determine the surface spread of flame of electrotechnical products or materials from which they are formed. It represents the current state of the art of the test methods and, where available, includes special observations on their relevance and use. The list of test methods is not to be considered exhaustive, and test methods that were not developed by the IEC are not to be considered as endorsed by the IEC unless this is specifically stated. This summary cannot be used in place of published standards which are the only valid reference documents. This basic safety publication is intended for use by technical committees in the preparation of standards in accordance with the principles laid down in IEC Guide 104 and ISO/IEC Guide 51. One of the responsibilities of a technical committee is, wherever applicable, to make use of basic safety publications in the preparation of its publications. The requirements, test methods or test conditions of this basic safety publication will not apply unless specifically referred to or included in the relevant publications. This International Standard is to be used in conjunction with IEC 60695-1. This second edition cancels and replaces the first edition of IEC 60695-9-2 published in 2014. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: a) Updated introduction b) Updated normative references c) Updated terms and definitions d) New Subclauses 4.1 and 4.2 e) Reference to fire stages as defined in ISO 19706 (Table 1) f) New sub-division of tests into the following subclauses: 4.3 Small-scale fire tests 4.4 Medium and intermediate-scale fire tests 4.5 Intermediate and large-scale fire tests for cables 4.6 Real-scale fire tests for cables g) Updated text in parts of Clause 4 h) Addition of the following test methods: IEC TS 60695-11-21 IEC 60684-2:2011, Clause 26 ISO 3582 ISO 9772 ISO 9773 ISO 12992 ISO 21367 i) New Clause 5 and Table 4 giving an overview of test methods j) Deletion of all the Annexes k) Updated bibliography

  • Standard
    44 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 60695-2-13:2021(Main)
Fire hazard testing - Part 2-13: Glowing/hot-wire based test methods - Glow-wire ignition temperature (GWIT) test method for materials
SIST EN IEC 60695-2-13:2021

This part of IEC 60695 specifies the details of the glow-wire test to be applied to test specimens of solid electrical insulating materials or other solid materials for ignitability testing to determine the glow-wire ignition temperature (GWIT). The GWIT is the temperature which is 25 K (or 30 K) higher than the maximum test temperature, determined during this standardized procedure, at which the tested material does not ignite, or sustained flaming combustion does not occur for a time longer than 5 s for any single flame event and the specimen is not totally consumed. This test is a materials test carried out on a series of standard test specimens. The data obtained, along with data from the glow-wire flammability index (GWFI) test method for materials, IEC 60695-2-12, can then be used in a preselection process in accordance with IEC 60695-1-30 [4] to judge the ability of materials to meet the requirements of IEC 60695-2-11. NOTE As an outcome of conducting a fire hazard assessment, an appropriate series of preselection flammability and ignition tests can allow a reduction of end product testing. This basic safety publication focusing on safety test method(s) is primarily intended for use by technical committees in the preparation of safety publications in accordance with the principles laid down in IEC Guide 104 and ISO/IEC Guide 51. One of the responsibilities of a technical committee is, wherever applicable, to make use of basic safety publications in the preparation of its publications.

  • Standard
    16 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 60695-1-12:2020(Main)
Fire hazard testing - Part 1-12: Guidance for assessing the fire hazard of electrotechnical products - Fire safety engineering
SIST EN IEC 60695-1-12:2020

IEC 60695-1-12:2015 is intended as a general guideline for IEC Product Committees and provides: - an explanation of the principles and uses of fire safety engineering; - guidance on the use of fire safety engineering in the design of electrotechnical products; - fire safety engineering terminology and concepts; - an indication of properties, data and tests needed for input into fire safety engineering assessments and - informative references. This international standard is not intended to be a detailed technical design guide, but is intended to provide guidance for product committees on fire safety engineering methods and performance based test information needs for use in performance based designs and fire hazard assessments of electrotechnical materials, assemblies, products and systems. This basic safety publication is intended for use by technical committees in the preparation of standards in accordance with the principles laid down in IEC Guide 104 and ISO/IEC Guide 51. Key words: Fire Hazard, Fire Test Method, Fire Safety Engineering This publication is to be read in conjunction with IEC 60695-1-10:2009 and IEC 60695-1-11:2014.

  • Standard
    34 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 60695-11-5:2017(Main)
Fire hazard testing - Part 11-5: Test flames - Needle-flame test method - Apparatus, confirmatory test arrangement and guidance
SIST EN 60695-11-5:2017

Specifies a needle-flame test to simulate the effect of a small flame which may result from fault conditions, in order to assess by a simulation technique the fire hazard. It is applicable to electrotechnical equipment, its sub-assemblies and components and to solid electrical insulating materials or other combustible materials. This first edition of EN 60695-11-5 cancels and replaces the second edition of EN 60695-2-2, issued in 1991 and its amendment 1 (1994). It also constitutes a technical revision. The structure of this standard remains essentially the same with some major new changes and concepts added: - The scope has been broadened to allow this test method to also simulate the effects of small flames from outside the equipment. - A new concept has been added which allows the burner to be moved during the test to avoid dripping material from falling onto the tip of the burner tube. - The burner tube material is now a referenced source. - The reference for the copper block material has changed - the ISO publication (ISO 1337) has been withdrawn with no replacement. A new callout is now used. - Informative Annex B and a bibliography have been added. It has the status of a basic safety publication in accordance with IEC Guide 104.

  • Standard
    26 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 60695-1-30:2017(Main)
Fire hazard testing - Part 1-30: Guidance for assessing the fire hazard of electrotechnical products - Preselection testing process - General guidelines
SIST EN 60695-1-30:2017

IEC 60695-1-30:2008 provides guidance for assessing and choosing candidate materials, components or sub-assemblies for making an end-product based upon preselection testing. It describes how preselection provides comparative fire hazard test methods to evaluate the performance of a test specimen and how preselection can be used in the selection of materials, parts, components and sub-assemblies during the design stage of an end-product. The major changes with respect to the previous edition are as follows: - Further explanation given in the introduction and Scope - Clause 3 changes to the definitions - Clause 4 clarifications of the principles of product design considering preselection - Clause 5 clarifications of the advantages and limitations of preselection - Clause 6 clarifications of the aspects of preselection relative to hazard assessment - Annex A changes in the references for examples of test methods which may be relevant to preselection - Annex B changes in the illustrative example of the flowchart of the use of preselection tests for resistance to fire hazards of a specific product type. This publication has the status of a basic safety publication in accordance with IEC Guide 104 and ISO/IEC Guide 51.

  • Standard
    17 pages
    English language
    sale 10% off
    e-Library read for
    1 day