EN IEC 62368-1:2024/A11:2024
(Amendment)Audio/video, information and communication technology equipment - Part 1: Safety requirements
Audio/video, information and communication technology equipment - Part 1: Safety requirements
2022-02-21: This prAA covers common mods to prEN IEC 62368-1 - PR=74334
Einrichtungen für Audio/Video-, Informations- und Kommunikationstechnik - Teil 1: Sicherheitsanforderungen
Équipements des technologies de l'audio/vidéo, de l'information et de la communication - Partie 1: Exigences de sécurité
No scope available
Oprema za avdio/video, informacijsko in komunikacijsko tehnologijo - 1. del: Varnostne zahteve - Dopolnilo A11
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-september-2024
Oprema za avdio/video, informacijsko in komunikacijsko tehnologijo - 1. del:
Varnostne zahteve - Dopolnilo A11
Audio/video, information and communication technology equipment - Part 1: Safety
requirements
Einrichtungen für Audio/Video-, Informations- und Kommunikationstechnik – Teil 1:
Sicherheitsanforderungen
Équipements des technologies de l'audio/vidéo, de l'information et de la communication -
Partie 1: Exigences de sécurité
Ta slovenski standard je istoveten z: EN IEC 62368-1:2024/A11:2024
ICS:
33.160.01 Avdio, video in avdiovizualni Audio, video and audiovisual
sistemi na splošno systems in general
35.020 Informacijska tehnika in Information technology (IT) in
tehnologija na splošno general
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD EN IEC 62368-1:2024/A11
NORME EUROPÉENNE
EUROPÄISCHE NORM April 2024
ICS 33.160.01; 35.020
English Version
Audio/video, information and communication technology
equipment - Part 1: Safety requirements
Équipements des technologies de l'audio/vidéo, de Einrichtungen für Audio/Video-, Informations- und
l'information et de la communication - Partie 1: Exigences Kommunikationstechnik - Teil 1: Sicherheitsanforderungen
de sécurité
This amendment A11 modifies the European Standard EN IEC 62368-1:2024; it was approved by CENELEC on 2024-02-15. CENELEC
members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this amendment the
status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This amendment exists in three official versions (English, French, German). A version in any other language made by translation under the
responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the same status as
the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Türkiye and the United Kingdom.
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2024 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 62368-1:2024/A11:2024 E
Contents Page
European foreword . 3
1 Modification to the whole document . 4
2 Modification to Clause 1 . 4
3 Modification to Clause 2 . 4
4 Modification to Clause 4 . 5
5 Modification to subclause 4.1.9 . 5
6 Modification to subclause 5.4.9.1 . 5
7 Modification to subclause 5.4.2.3.2.4 . 5
8 Modification to subclause 5.6.6.2 . 5
9 Modification to subclause 9.3.1 . 6
10 Modification to subclause 10.2.1 . 6
11 Modification to subclause 10.4.1 . 6
12 Modification to subclause 10.4.4 . 6
13 Modification to subclause 10.5.1 . 6
14 Modification to subclause 10.5.3 . 7
15 Modification to Clause 10 . 7
16 Modification to subclause G.3.1.2 . 12
17 Modification to subclause G.7.1 . 12
18 Modification to subclause M.2. 12
19 Modification to the Bibliography . 12
20 Addition of annexes . 13
Annex ZA (normative) Normative references to international publications with their
corresponding European publications . 14
Annex ZB (normative) Special national conditions. 25
Annex ZC (informative) A-deviations . 29
Annex ZD (informative) IEC and CENELEC code designations for flexible cords . 30
European foreword
This document (EN IEC 62368-1:2024/A11:2024) has been prepared by CLC/TC 108X “Safety of electronic
equipment within the fields of Audio/Video, Information Technology and Communication Technology”.
The following dates are fixed:
• latest date by which this document has to be (dop) 2025-02-15
implemented at national level by publication of
an identical national standard or by
endorsement
• latest date by which the national standards (dow) 2027-02-15
conflicting with this document have to be
withdrawn
This document modifies EN IEC 62368-1:2024.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
Clauses, subclauses, notes, tables, figures and annexes which are additional to those in IEC 62368-1:2023
are prefixed “Z”.
This document has been prepared under a standardization request addressed to CENELEC by the European
Commission. The Standing Committee of the EFTA States subsequently approves these requests for its
Member States.
Any feedback and questions on this document should be directed to the users’ national committee. A
complete listing of these bodies can be found on the CENELEC website.
1 Modification to the whole document
Delete all the “country” notes in the reference document according to the following list:
0.2.1 Note 1 and 1 Note 4 and 3.3.8.1 Note 2
Note 2 Note 5
3.3.8.3 Note 1 4.1.15 Note 4.7.3 Note 1 and
Note 2
5.4.2.3.2.2 Note c 5.4.2.3.2.4 Note 1 and 5.4.2.3.2.4 Note 2
Table 12 Note 3 Table 13
5.4.2.5 Note 2 5.4.5.1 Note 5.4.10.2.1 Note
5.4.10.2.2 Note 5.4.10.2.3 Note
5.5.2.1 Note 5.5.6 Note 5.6.4.2.1 Note 2 and
Note 3 and
Note 4
5.6.8 Note 2 5.7.7.1 Note 1 and 8.5.4.2.3 Note
Note 2
10.2.1 Note 3 and 10.5.3 Note 2 10.6.1 Note 3
Table 39 Note 4 and
Note 5
F.3.3.4 Note 2 F.3.3.6 Note 3 Y.4.1 Note
Y.4.5 Note
2 Modification to Clause 1
Add the following note at the end of Clause 1:
“NOTE Z1 The use of certain substances in electrical and electronic equipment is restricted within the EU: see
Directive 2011/65/EU.”
Add the following paragraph and note after Note 5:
“This document is a type test standard.
NOTE Z2 Routine tests of complete equipment, sub-assemblies or components are covered by EN 62911.”
3 Modification to Clause 2
Add the following references:
EN 71-1:2014+A1:2018, Safety of toys - Part 1: Mechanical and physical properties
EN 50332-1:2013, Sound system equipment: Headphones and earphones associated with personal music
players - Maximum sound pressure level measurement methodology - Part 1: General method for "one
package equipment"
EN 50332-2:2013, Sound system equipment: Headphones and earphones associated with personal music
players - Maximum sound pressure level measurement methodology - Part 2: Matching of sets with
headphones if either or both are offered separately, or are offered as one package equipment but with
standardised connectors between the two allowing to combine components of different manufacturers or
different design
EN 50332-3:2017, Sound system equipment: headphones and earphones associated with personal music
players - Maximum sound pressure level measurement methodology - Part 3: Measurement method for sound
dose management
IEC/TR 62471-2, Photobiological safety of lamps and lamp systems - Part 2: Guidance on manufacturing
requirements relating to non-laser optical radiation safety
4 Modification to Clause 4
Add the following new subclause 4.Z1 after subclause 4.9:
“For compliance with B.3 and B.4 in circuits connected to an AC mains, protective devices shall be provided,
subject to the following:
— for pluggable equipment type A, the protective devices shall be included as parts of the equipment,
with the exception of components in series with the mains input to the equipment such as the supply
cord, appliance coupler, r.f.i. filter and switch, for which the building installation shall be regarded as
providing protection in accordance with the rating of the wall socket outlet;
— for pluggable equipment type B or permanently connected equipment, the protection may be the
dedicated overcurrent and short-circuit protection in the building installation, provided that the means of
protection, for example a fuse or circuit breaker, is fully specified in the installation instructions.
Where protective devices are required within the equipment, the protective devices within the equipment
shall operate before or at the same time the expected building installation protection will operate.
For earth faults in single-phase equipment, it is not necessary to provide 2 protective devices. It is expected
that the building installation will protect against earth faults. This applies also in countries where an IT power
distribution system is used.”
5 Modification to subclause 4.1.9
Add the following paragraph at the end of this subclause:
“Products need to comply with the requirements of this document with appropriate measurement uncertainty.
NOTE Z1 See also the ADCO RED position on ‘Measurement uncertainty in published harmonized standards’.”
6 Modification to subclause 5.4.9.1
Add the following note after the 5th paragraph:
“NOTE Z1 For guidance on the use of high voltage source, see IEC 60060-1, Clause 8 of IEC 60243-1 and IEC 61180.”
7 Modification to subclause 5.4.2.3.2.4
Add the following at the end of this subclause:
“The requirement for interconnection with external circuit in a HBES/BACS network is in addition given in
EN IEC 63044-3:2018.”
8 Modification to subclause 5.6.6.2
Replace item d) with the following:
“d) For equipment powered from a DC mains, if the protective current rating of the circuit under test
exceeds 25 A, the test current shall be minimum as required in item a), unless the manufacturer specifies a
higher value.”
9 Modification to subclause 9.3.1
Replace the second paragraph with the following:
“An accessible part that, while in contact with the body, is likely to drop in temperature upon touch can be
evaluated under the limits of Annex A of IEC Guide 117:2010 using the test method of 4.5 of IEC Guide 117.”
10 Modification to subclause 10.2.1
c) d)
Add the following to and in Table 38:
“For additional requirements, see 10.5.1.”
11 Modification to subclause 10.4.1
Replace the second paragraph of 10.4.1 with:
“Electronic light effect equipment does not have to comply with the requirements of 10.4. However,
IEC/TR 62471-2 shall be considered and proper installation instructions shall be provided.”
Replace the ninth paragraph of 10.4.1 with:
“The following information shall be provided in the user manual for safe operation and installation. This
information shall also be provided for safe operation by a skilled person who may be exposed to Risk
Group 3 energy levels.
Adequate instructions for proper assembly, installation, maintenance and safe use, including clear warnings
concerning precautions to avoid possible exposure to hazardous optical radiation; and
Advice on safe operating procedures and warnings concerning reasonably foreseeable misuse,
malfunctions and hazardous failure modes. Where servicing and maintenance procedures are detailed, they
shall include explicit instructions on safe procedures to be follo
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.