iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CLC

EN 60512-24-1:2012

(Main)

Connectors for electronic equipment - Tests and measurements - Part 24-1: Magnetic interference tests - Test 24a: Residual magnetism

Connectors for electronic equipment - Tests and measurements - Part 24-1: Magnetic interference tests - Test 24a: Residual magnetism

IEC 60512-24-1:2010 when required by the detail specification, is used for testing connectors within the scope of technical committee 48. It may also be used for similar devices when specified in a detail specification. The object of this standard is to detail a standard method to measure the residual magnetism of a connector after exposure to a specified magnetic field.

Steckverbinder für elektronische Einrichtungen - Mess- und Prüfverfahren - Teil 24-1: Prüfungen im magnetischen Störfeld - Prüfung 24a: Restmagnetismus

Connecteurs pour équipements électroniques - Essais et mesures - Partie 24-1: Essais de perturbations magnétiques - Essai 24a: Magnétisme résiduel

La CEI 60512-24-1:2010 est utilisée pour les essais des connecteurs du domaine d'activité du comité d'études 48, lorsque la spécification particulière l'exige. Elle peut également être utilisée pour des dispositifs similaires lorsqu'une spécification particulière le stipule. L'objet de cette norme est de définir une méthode normalisée pour mesurer le magnétisme résiduel d'un connecteur après son exposition à un champ magnétique spécifié.",PE

Konektorji za elektronsko opremo - Preskusi in meritve - 24-1. del: Preskušanje elektromagnetnega motenja - Preskus 24a: Preostali magnetizem

Ta del standarda IEC 60512 se uporablja, če tako zahteva podrobna specifikacija, za preskušanje konektorjev na področju uporabe tehničnega odbora 48. Lahko se uporablja tudi za podobne elemente, če je tako določeno v podrobni specifikaciji. Cilj tega standarda je opredeliti standardno metodo za merjenje preostalega magnetizma konektorja po izpostavljenosti določenemu magnetnemu polju.

General Information

Status
Published
Publication Date
15-Nov-2012
Withdrawal Date
27-Apr-2015
ICS
31.220.01 - Electromechanical components in general
Technical Committee
CLC/SR 48B - Connectors
Drafting Committee
IEC/SC 48B - IEC_SC_48B
Parallel Committee
IEC/SC 48B - IEC_SC_48B
Current Stage
6060 - Document made available - Publishing
Start Date
16-Nov-2012
Completion Date
16-Nov-2012
Ref Project
SIST EN 60512-24-1:2013 - Connectors for electronic equipment - Tests and measurements - Part 24-1: Magnetic interference tests - Test 24a: Residual magnetism

Buy Standard

EN 60512-24-1:2013EN 60512-24-1:2013
PreviousNext
Standard
EN 60512-24-1:2013
English language
6 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI STANDARD
01-marec-2013
Konektorji za elektronsko opremo - Preskusi in meritve - 24-1. del: Preskušanje
elektromagnetnega motenja - Preskus 24a: Preostali magnetizem
Connectors for electronic equipment - Tests and measurements - Part 24-1: Magnetic
interference tests - Test 24a: Residual magnetism
Ta slovenski standard je istoveten z: EN 60512-24-1:2012
ICS:
17.220.20 0HUMHQMHHOHNWULþQLKLQ Measurement of electrical
PDJQHWQLKYHOLþLQ and magnetic quantities
31.220.10 9WLþLLQYWLþQLFHNRQHNWRUML Plug-and-socket devices.
Connectors
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN 60512-24-1
NORME EUROPÉENNE
November 2012
EUROPÄISCHE NORM
ICS 31.220.01
English version
Connectors for electronic equipment -
Tests and measurements -
Part 24-1: Magnetic interference tests -
Test 24a: Residual magnetism
(IEC 60512-24-1:2010)
Connecteurs pour équipements Steckverbinder für elektronische
électroniques - Essais et mesures - Einrichtungen - Mess- und Prüfverfahren -
Partie 24-1: Essais de perturbations Teil 24-1: Prüfungen im magnetischen
magnétiques - Essai 24a: Magnétisme Störfeld - Prüfung 24a: Restmagnetismus
résiduel (IEC 60512-24-1:2010)
(CEI 60512-24-1:2010)
This European Standard was approved by CENELEC on 2010-04-28. CENELEC members are bound to comply
with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard
the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the CEN-CENELEC Management Centre or to any CENELEC member.

This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and notified
to the CEN-CENELEC Management Centre has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus,
the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany,
Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.

CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung

Management Centre: Avenue Marnix 17, B - 1000 Brussels

© 2012 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 60512-24-1:2012 E
Foreword
The text of document 48B/2027/CDV, future edition 1 of IEC 60512-24-1, prepared by SC 48B
"Connectors" of IEC/TC 48 "Electromechanical components and mechanical structures for electronic
equipment" was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as
The following dates are fixed:
(dop) 2013-05-16
• latest date by which the document has
to be implemented at national level by
publication of an identical national
standard or by endorsement
(dow) 2015-04-28
• latest date by which the national
standards conflicting with the
document have to be withdrawn
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such
patent rights.
Endorsement notice
The text of the International Standard IEC 60512-24-1:2010 was approved by CENELEC as a
European Standard without any modification.

IEC 60512-24-1 ®
Edition 1.0 2010-03
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Connectors for electronic equipment – Tests and measurements –
Part 24-1: Magnetic interference tests – Test 24a: Residual magnetism

Connecteurs pour équipements électroniques – Essais et mesures –
Partie 24-1: Essais de perturbations magnétiques – Essai 24a: Magnétisme
résiduel
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
PRICE CODE
INTERNATIONALE
D
CODE PRIX
ICS 31.220.01 ISBN 978-2-88910-205-1
– 2 – 60512-24-1 © IEC:2010
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
CONNECTORS FOR ELECTRONIC EQUIPMENT –
TESTS AND MEASUREMENTS –
Part 24-1: Magnetic interference tests –
Test 24a: Residual magnetism
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entr
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CLC
EN IEC 60512-9-5:2020(Main)
Connectors for electrical and electronic equipment - Tests and measurements - Part 9-5: Endurance tests - Test 9e: Current loading, cyclic
SIST EN IEC 60512-9-5:2020

IEC 60512-9-5:2020 is available as IEC 60512-9-5:2020 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 60512-9-5:2020 when required by the detail product specification, is used for testing connectors or solderless connections within the scope of technical committee 48. It may also be used for similar devices when specified in a detail product specification. The object of this document is to detail a standard method for subjecting solderless connections to thermal stress conditioning by cyclic current loading. This second edition cancels and replaces the first edition published in 2010. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: - added method B and renamed the former test method as method A, to provide an alternative with more adjustable time “ON” and “OFF” for products with larger thermal mass. - added introduction to provide background of this revision.

  • Standard
    14 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 60512-11-1:2019(Main)
Connectors for electrical and electronic equipment - Tests and measurements - Part 11-1: Climatic tests - Test 11a - Climatic sequence
SIST EN IEC 60512-11-1:2019

IEC 60512-11-1:2019 when required by the detail (product) specification, is used for testing connectors within the scope of IEC technical committee 48. This test may also be used for similar devices (i.e. when the degradation mechanisms are the same) when specified in a detail (product) specification. The object of this test is to define a standard test method to assess the ability of connectors to function in a specified manner, in a specified environment which might be encountered during normal use, including storage. This document provides a standard composite test method for determining the suitability of connectors when subjected to environmental conditions consisting of a sequence of temperature, humidity and, where required, low air pressure environmental stresses. Key words: Connectors, Climatic Tests

  • Standard
    15 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 60512-23-3:2019(Main)
Connectors for electrical and electronic equipment - Tests and measurements - Part 23-3: Screening and filtering tests - Test 23c: Shielding effectiveness of connectors and accessories - Line injection method
SIST EN IEC 60512-23-3:2019

This part of IEC 60512 defines a standard test method for measuring the shielding effectiveness SE of a shielded connector, or of a connector not provided with integral shield once fitted with a shielding accessory and terminated with a screened cable. The complete assembly has a continuous 360° shielding capability throughout its length. NOTE 1 Practically, continuous 360° shielding is not always achievable based on the geometry of the connector. NOTE 2 Shielding" is used in this document with the same meaning as "screening". This test method can be applied to shielded connectors and to connector accessories with shielding capability. The following different connector designs can be tested: - circular connectors; - rectangular connectors; - connectors for printed boards; - connector shielding accessories. NOTE 3 For the definition of "accessory" see IEV 581-24-10. A shielding accessory i.e. an accessory that confers shielding to a non-inherently shielded connector, may be a suitable set of shielded housings providing electrical continuity, along the mated connector set, between the screen of the (screened) cable at the cable outlet of the free cable connector housing and the metallic mounting surface for the fixed connector housing. The free connector housing is provided with a cable screen clamp. This test method utilizes the principle that the intrinsic shielding property of the connector/accessory/cable assembly is its surface transfer impedance ZT which can be expressed as the longitudinal voltage inside the shield, relative to the current flow on the outside shell. This test method is based on two impedance-matched circuits. See Figure 1 for the measurement principle. The connector specimen under test is integrated into the secondary circuit 02. The impedance-matched injection line of the primary circuit 01, which activates the electromagnetic field, runs parallel to the surface of the specimen under test. This test is also suitable for measuring the shielding effectiveness of a connector fitted with triaxial contacts terminated with shielded, twisted pair cables, as used in data bus systems. NOTE 4 This standard has been adopted by ASD-STAN (formerly known as AECMA) as EN 2591-212.

  • Standard
    18 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 60512-8-3:2018(Main)
Connectors for electrical and electronic equipment - Tests and measurements - Part 8-3: Static load tests (fixed connectors) - Test 8c: Robustness of actuating lever
SIST EN IEC 60512-8-3:2018

IEC 60512-8-3:2018 this part of IEC 60512, when required by the detail (product) specification, is used for testing connectors within the scope of IEC technical committee 48. It may also be used for similar devices, when specified in a detail (product) specification. The object of this document is to detail a standard test method to assess the robustness of the actuating lever of a connector mating or release mechanism. This second edition cancels and replaces the first edition published in 2011. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: this edition reflects IEC 60512-1-101, Blank detail specification and Subclause 4.2 (Preparation of specimen) is improved.

  • Standard
    12 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 60512-9-2:2012(Main)
Connectors for electronic equipment - Tests and measurements - Part 9-2: Endurance tests - Test 9b: Electrical load and temperature
SIST EN 60512-9-2:2012

IEC 60512-9-2:2011 when required by the detail specification, this part of IEC 60512, is used for testing connectors within the scope of technical committee 48. It may also be used for similar devices when specified in a detail specification. The object of this standard is to detail a standard test method to assess the ability of a connector to withstand elevated temperatures with electrical loading. This standard cancels and replaces Test 9b of IEC 60512-5, issued in 1992.

  • Standard
    10 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 60512-7-2:2012(Main)
Connectors for electronic equipment - Tests and measurements - Part 7-2: Impact tests (free connectors) - Test 7b: Mechanical strength impact
SIST EN 60512-7-2:2012

IEC 60512-7-2:2011 when required by the detail specification, is used for testing connectors within the scope of technical committee 48. It may also be used for similar devices when specified in a detail specification. The object of this standard is to detail a standard test method to assess the ability of a free connector on the end of a cable or wire bundle to withstand impacts it could receive when dropped onto a hard surface.

  • Standard
    11 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 60512-9-3:2011(Main)
Connectors for electronic equipment - Tests and measurements - Part 9-3: Endurance tests - Test 9c: Mechanical operation (engaging/separating) with electrical load
SIST EN 60512-9-3:2011

IEC 60512-9-3:2011 defines a standard test method to assess the mechanical and electrical operational endurance, i.e. engaging and separating cycles, of a connector in an operating mode which includes a specified electrical load. This second edition cancels and replaces Test 9c of IEC 60512-5, issued in 1992, and constitutes a technical revision. The main technical changes with regard to the previous edition are as follows: - An additional requirement to 4.1 stating that if more than one electrical circuit is wired for testing, the wiring shall be carried out in a parallel electrical circuit. - Subclauses 4.3 through 4.7 were removed and replaced by 4.2 through 4.4. This publication is to be read in conjunction with IEC 60512-1:2001 and IEC 60512-1-100:2006.

  • Standard
    12 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 60512-17-2:2011(Main)
Connectors for electronic equipment - Tests and measurements - Part 17-2: Cable clamping tests - Test 17b: Cable clamp resistance to cable rotation
SIST EN 60512-17-2:2011

IEC 60512-17-2:2011 when required by the detail specification, is used for testing connectors within the scope of IEC technical committee 48. It may also be used for similar devices when specified in a detail specification. The object of this standard is to detail a standard method to assess the ability of a cable-clamping device to allow rotary movement of the cable/wire bundle without damage to the external surface of the cable/wire bundle, the cable-clamping device, the connector or the sub-assembly. This standard cancels and replaces Test 17b of IEC 60512-5, issued in 1992, and constitutes a technical revision. This publication is to be read in conjunction with  IEC 60512-1:2001 and IEC 60512-1-100:2006.

  • Standard
    9 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 60512-9-4:2011(Main)
Connectors for electronic equipment - Tests and measurements - Part 9-4: Endurance tests - Test 9d: Durability of contact retention system and seals (maintenance, ageing)
SIST EN 60512-9-4:2011

IEC 60512-9-4:2011 when required by the detail specification, is used for testing connectors within the scope of IEC technical committee 48. It may also be used for similar devices when specified in a detail specification. The object of this standard is to detail a standard test method to assess the ability of a connector to withstand stresses caused by repeated extraction and insertion of contacts during maintenance. This standard cancels and replaces Test 9d of IEC 60512-5, issued in 1992, and constitutes a technical revision. This publication is to be read in conjunction with  IEC 60512-1:2001 and IEC 60512-1-100:2006.

  • Standard
    9 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 60512-8-2:2011(Main)
Connectors for electronic equipment - Tests and measurements - Part 8-2: Static load tests (fixed connectors) - Test 8b: Static load, axial
SIST EN 60512-8-2:2011

IEC 60512-8-2:2011 when required by the detail specification, is used for testing connectors within the scope of IEC technical committee 48. It may also be used for similar devices when specified in a detail specification. The object of this standard is to detail a standard test method to determine the ability of a fixed connector to withstand a steady axial force which might occur during normal use. This standard cancels and replaces Test 8b of IEC 60512-5, issued in 1992, and constitutes a technical revision. This publication is to be read in conjunction with IEC 60512-1:2001 and IEC 60512-1-100:2006.

  • Standard
    10 pages
    English language
    sale 10% off
    e-Library read for
    1 day