ETSI EN 302 574-1 V2.1.1 (2016-06)

Satellite Earth Stations and Systems (SES); Harmonised Standard for Mobile Earth Stations (MES) operating in the 1 980 MHz to 2 010 MHz (earth-to-space) and 2 170 MHz to 2 200 MHz (space-to-earth) frequency bands covering the essential requirements of article 3.2 of the Directive 2014/53/EU; Part 1: Complementary Ground Component (CGC) for wideband systems

REN/SES-00369

Satelitske zemeljske postaje in sistemi (SES) - Harmonizirani standard za satelitske zemeljske postaje (MES) za MSS, ki delujejo v frekvenčnem pasu 2 GHz - 1. del: Komplementarna talna komponenta (CGC) za širokopasovne sisteme, ki zajema bistvene zahteve člena 3.2 direktive 2014/53/EU

Ta dokument se uporablja za komplementarne talne komponente (CGC), ki delujejo kot del satelitskega omrežja.
Ta dokument zajema dve vrsti komplementarnih talnih komponent:
• konvencionalne komplementarne talne komponente:
– točki 4 in 5 skladno s standardom ETSI EN 301 908-18 [16] za W_CDMA;
– točki 8 in 9 skladno s standardom ETSI EN 301 908-14 [10] za E-UTRA;
• letalske komplementarne talne komponente
Te komplementarne talne komponente (CGC) izključno oddajajo uporabniški opremi/letalskemu terminalu oziroma oddajajo uporabniški opremi/letalskemu terminalu in od njega sprejemajo v frekvenčnih pasovih, ki so primarno dodeljeni mobilni satelitski storitvi (MSS), kot je opredeljeno v preglednici 1.
OPOMBA 1: komplementarne talne komponente lahko vključujejo različne vrste vmesnikov do zemeljskih in/ali satelitskih omrežij, vendar njihove značilnosti ne spadajo v področje uporabe tega dokumenta.
Ta dokument se uporablja za tip radijske opreme komplementarnih talnih komponent (CGC), ki se uporabljajo v sistemih mobilnih satelitskih storitev z naslednjimi značilnostmi:
• Komplementarne talne komponente imajo lahko sposobnost oddajanja in sprejemanja ter so del hibridnega satelitskega/prizemnega omrežja.
• Komplementarne talne komponente delujejo s pasovno širino signala dodeljenega kanala (CBw), ki je 1 MHz ali večja.
• Konvencionalne komplementarne talne komponente so lahko talne komponente z lokalno, srednjo ali široko pokritostjo.
• Letalske komplementarne talne komponente lahko oddajajo terminalom, montiranim na letalih (letalski terminali),
in od njih sprejemajo.
• Komplementarne talne komponente so lahko sestavni del večnačinovne bazne postaje. Sestavljene so lahko iz več modulov s povezanimi priključki ali so samozadostna enota.
Če je komplementarna talna komponenta sestavni del večnačinovne bazne postaje, zahteve tega dokumenta veljajo samo za komplementarno talno komponento v terminalu, ki deluje v frekvenčnih pasovih MSS, podanih v preglednici 1, razen če je v dokumentu drugače navedeno.
Ta dokument se uporablja za naslednje tipe terminalske opreme:
1) komplementarne talne komponente za širokopasovne satelitske sisteme.
Ta tip radijske opreme lahko deluje v vseh delih frekvenčnih pasov iz preglednice 1.
Ta dokument se uporablja za radijske vmesnike med konvencionalno komplementarno talno komponento in uporabniško opremo ali med letalsko komplementarno talno komponento in letalskim terminalom.
Ta dokument zajema določbe člena 3.2 Direktive 2014/53/EU [13] (direktive RE), ki navaja: »/.../ Radijska oprema je izdelana tako, da optimalno uporablja in podpira učinkovito izrabo radijskega spektra, z namenom preprečevanja škodljivega motenja.«
OPOMBA 2: poleg mejnih vrednosti neželenih oddajanj, opredeljenih v točkah 4.2.2 in 5.2.2 tega dokumenta, so lahko potrebne dodatne omejitve delovanja za preprečevanje škodljivih motenj storitev, ki delujejo v sosednjih pasovih zunaj delovnega pasu, ki je opredeljen v preglednici 1.
Poleg tega dokumenta se lahko za opremo na področju uporabe tega dokumenta uporabljajo tudi drugi standardi EN, ki določajo tehnične zahteve v zvezi z bistvenimi zahtevami iz drugih delov člena 3 Direktive 2014/53/EU [13].
OPOMBA 3: seznam tovrstnih evropskih standardov je na voljo na spletnem mestu http://www.newapproach.org.

General Information

• Status: Published
• Publication Date: 16-Jun-2016
• Technical Committee: SES SCN - Satellite Communications and Navigation
• Current Stage: 12 - Delivery to the EC
• Due Date: 06-Jul-2016
• Completion Date: 17-Jun-2016
• Ref Project: SIST EN 302 574-1 V2.1.1:2016 - Satellite Earth Stations and Systems (SES) - Harmonised Standard for Satellite Earth Stations (MES) for MSS operating in the 2 GHz frequency band - Part 1: Complementary Ground Component (CGC) for wideband systems covering the essential requirements of article 3.2 of the Directive 2014/53/EU

Overview

ETSI EN 302 574-1 V2.1.1 (2016-06) (aligned with ETSI EN 302 574-1 V2.1.1) is a harmonised European standard for Complementary Ground Components (CGC) used in Mobile Satellite Service (MSS) wideband systems operating in the 2 GHz frequency band. It specifies radio-interface technical requirements and test methods that demonstrate conformity with the essential requirement of Article 3.2 of Directive 2014/53/EU (RE Directive) - that radio equipment must effectively use and support the efficient use of radio spectrum to avoid harmful interference.

The standard covers CGC equipment that:

• Operates in the 1 980–2 010 MHz (earth-to-space) and 2 170–2 200 MHz (space-to-earth) bands;
• Has assigned channel bandwidth (CBw) of 1 MHz or greater;
• May be part of hybrid satellite/terrestrial networks or multi-mode base stations;
• Includes conventional CGC (local/medium/wide coverage) and aeronautical CGC (communicating with aircraft terminals).

Note: terrestrial interface specifications are out of scope.

Key Topics and Technical Requirements

The standard focuses on RF performance, coexistence and conformance testing, including:

• Spectrum emission mask - definitions, limits and conformance procedures to control out‑of‑band emissions.
• Adjacent Channel Leakage Ratio (ACLR) - transmitter adjacent-channel protection requirements.
• Transmitter spurious emissions and receiver spurious emissions - limits and test methods to prevent interference with neighbouring services.
• Maximum output power, transmit intermodulation, and receiver inter‑modulation characteristics.
• Receiver blocking and adjacent channel selectivity (ACS) - receiver robustness against strong out-of-band signals.
• Detailed test suites and measurement procedures (environmental test conditions, measurement interpretation).
• Environmental profile and deployment considerations for conventional vs aeronautical CGC.

The document references and aligns certain clauses with ETSI EN 301 908-18 (W_CDMA) and ETSI EN 301 908-14 (E-UTRA) where applicable.

Practical Applications and Who Uses It

This harmonised standard is intended for:

• Equipment manufacturers designing CGC modules or multi‑mode base station elements for MSS in the 2 GHz band.
• Test laboratories performing RF conformance testing for CE marking under the RE Directive (Article 3.2).
• Certification bodies and notified bodies assessing compliance with spectrum-efficient design requirements.
• Network operators and system integrators deploying hybrid satellite/terrestrial systems, including aeronautical service providers.
• Regulators and spectrum managers evaluating coexistence and interference mitigation measures.

Using SIST EN 302 574-1 helps stakeholders ensure predictable coexistence, meet regulatory obligations, and reduce risk of harmful interference in the MSS 2 GHz band.

Related Standards

• ETSI EN 302 574-1 (ETSI parent document)
• ETSI EN 301 908-18 (W_CDMA clauses referenced)
• ETSI EN 301 908-14 (E-UTRA clauses referenced)
• Other harmonised ENs covering additional essential requirements of Directive 2014/53/EU (listed via http://www.newapproach.org).

Standards Content (Sample)

Draft ETSI EN 302 574-1 V2.1.0 (2016-03)

HARMONISED EUROPEAN STANDARD
Satellite Earth Stations and Systems (SES);
Harmonised Standard for Satellite Earth Stations (MES) for
MSS operating in the 2 GHz frequency band;
Part 1: Complementary Ground
Component (CGC) for wideband systems
covering the essential requirements
of article 3.2 of the Directive 2014/53/EU

2 Draft ETSI EN 302 574-1 V2.1.0 (2016-03)

Reference
REN/SES-00369
Keywords
broadband, IMT, mobile, satellite
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: [phone]  Fax: [phone]

Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88

Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.

© European Telecommunications Standards Institute 2016.
All rights reserved.
TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.
TM
3GPP and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI
3 Draft ETSI EN 302 574-1 V2.1.0 (2016-03)
Contents
Intellectual Property Rights . 9
Foreword . 9
Modal verbs terminology . 9
Introduction . 10
1 Scope . 11
2 References . 12
2.1 Normative references . 12
2.2 Informative references . 13
3 Definitions, symbols and abbreviations . 13
3.1 Definitions . 13
3.2 Symbols . 14
3.3 Abbreviations . 15
4 Technical requirements specifications for conventional CGC . 16
4.1 Environmental profile . 16
4.2 Conformance requirements . 16
4.2.1 Introduction. 16
4.2.2 Spectrum emission mask . 16
4.2.2.1 Definition . 16
4.2.2.2 Limits . 17
4.2.2.3 Conformance . 18
4.2.3 Adjacent channel leakage power ratio (ACLR) . 18
4.2.3.1 Definition . 18
4.2.3.2 Limits . 18
4.2.3.3 Conformance . 19
4.2.4 Transmitter spurious emis sions . 19
4.2.4.1 Definition . 19
4.2.4.2 Limits . 19
4.2.4.2.1 Spurious emissions . 19
4.2.4.2.2 Coexistence with other systems in the same geographical area. 20
4.2.4.2.3 Protection of UTRA FDD in adjacent frequency band . 20
4.2.4.2.4 Protection of UTRA -TDD . 20
4.2.4.2.5 Protection of UTRA BS . 20
4.2.4.2.6 Protection of the CGC receiver of own or different CGC . 21
4.2.4.3 Conformance . 21
4.2.5 CGC maximum output power . 21
4.2.5.1 Definition . 21
4.2.5.2 Limit . 21
4.2.5.3 Conformance . 21
4.2.6 Transmit inter modulation . 21
4.2.6.1 Definition . 21
4.2.6.2 Limit . 22
4.2.6.3 Conformance . 22
4.2.7 Receiver spurious emissions . 22
4.2.7.1 Definition . 22
4.2.7.2 Limits . 22
4.2.7.3 Conformance . 22
4.2.8 Blocking characteristics . 22
4.2.8.1 Definition . 22
4.2.8.2 Limit . 22
4.2.8.3 Conformance . 23
4.2.9 Receiver inter-modulation characteristics . 23
4.2.9.1 Definition . 23
4.2.9.2 Limit . 23
4.2.9.3 Conformance . 24
ETSI
4 Draft ETSI EN 302 574-1 V2.1.0 (2016-03)
4.2.10 Receiver adjacent selectivity. 24
4.2.10.1 Definition . 24
4.2.10.2 Limit . 24
4.2.10.3 Conformance . 25
5 Testing for compliance with technical requirements for conventional CGC . 25
5.1 Environmental and other conditions for testing . 25
5.2 Interpretation of the measurement results . 26
5.3 Radio test suites . 27
5.3.1 Spectrum emission mask . 27
5.3.1.1 Initial conditions . 27
5.3.1.2 Procedures . 28
5.3.2 Adjacent Channel leakage Power Ratio (ACLR). 28
5.3.2.1 Initial conditions . 28
5.3.2.2 Procedure . 28
5.3.3 Transmitter spurious emis sions . 28
5.3.3.1 Initial conditions . 28
5.3.3.2 Procedure . 29
5.3.4 CGC maximum output power . 29
5.3.4.1 Initial conditions . 29
5.3.4.2 Procedure . 29
5.3.5 Transmit intermodulation . 29
5.3.5.1 Initial conditions . 29
5.3.5.2 Procedures . 29
5.3.6 Receiver spurious emissions . 30
5.3.6.1 Initial conditions . 30
5.3.6.2 Procedure . 30
5.3.7 Blocking characteristics . 30
5.3.7.1 Initial conditions . 30
5.3.7.2 Procedure . 31
5.3.8 Receiver intermodulation characteristics . 31
5.3.8.1 Initial conditions . 31
5.3.8.2 Procedures . 31
5.3.9 Receiver Adjacent Channel Selectivity (ACS) . 31
5.3.9.1 Initial conditions . 31
5.3.9.2 Procedure . 32
6 Technical requirements specifications for Aeronautical CGC . 32
6.1 Environmental profile . 32
6.2 Conformance requirements . 32
6.2.1 Introduction. 32
6.2.2 Spectrum emission mask . 33
6.2.2.1 Definition . 33
6.2.2.2 Limits . 33
6.2.2.3 Conformance . 33
6.2.3 Adjacent channel leakage power ratio (ACLR) . 33
6.2.3.1 Definition . 33
6.2.3.2 Limits . 33
6.2.3.3 Conformance . 34
6.2.4 Transmitter spurious emis sions . 34
6.2.4.1 Definition . 34
6.2.4.2 Limits . 34
6.2.4.2.1 CGC Spurious emissions . 34
6.2.4.2.2 Coexistence with other systems . 34
6.2.4.2.3 Protection of BS receiver . 35
6.2.4.3 Conformance . 35
6.2.5 Aeronautical CGC maximum output power . 36
6.2.5.1 Definition . 36
6.2.5.2 Limit . 36
6.2.5.3 Conformance . 36
6.2.6 Transmit intermodulation . 36
6.2.6.1 Definition . 36
ETSI
5 Draft ETSI EN 302 574-1 V2.1.0 (2016-03)
6.2.6.2 Limit . 36
6.2.6.3 Conformance . 37
6.2.7 Receiver spurious emissions . 37
6.2.7.1 Definition . 37
6.2.7.2 Limits . 37
6.2.7.3 Conformance . 37
6.2.8 Blocking characteristics . 37
6.2.8.1 Definition . 37
6.2.8.2 Limit . 37
6.2.8.3 Conformance . 38
6.2.9 Receiver intermodulation characteristics . 38
6.2.9.1 Definition . 38
6.2.9.2 Limit . 38
6.2.9.3 Conformance . 39
6.2.10 Receiver adjacent Channel selectivity and narrow-band blocking . 39
6.2.10.1 Definition . 39
6.2.10.2 Limit . 39
6.2.10.3 Conformance . 40
7 Testing for compliance with technical requirements for Aeronautical CGC . 40
7.1 Environmental and other conditions for testing . 40
7.2 Interpretation of the measurement results . 41
7.3 Radio test suites . 42
7.3.1 Spectrum emission mask . 42
7.3.1.1 Initial conditions . 42
7.3.1.2 Procedures . 43
7.3.2 Adjacent Channel leakage Power Ratio (ACLR). 43
7.3.2.0 General . 43
7.3.2.1 Initial conditions . 43
7.3.2.2 Procedure . 43
7.3.3 Transmitter spurious emis sions . 43
7.3.3.1 Initial conditions . 43
7.3.3.2 Procedure . 44
7.3.4 Aeronautical CGC maximum output power . 44
7.3.4.1 Initial conditions . 44
7.3.4.2 Procedure . 44
7.3.5 Transmit intermodulation . 44
7.3.5.1 Initial conditions . 44
7.3.5.2 Procedures . 45
7.3.6 Receiver spurious emissions . 45
7.3.6.1 Initial conditions . 45
7.3.6.2 Procedure . 45
7.3.7 Blocking characteristics . 46
7.3.7.1 Initial conditions . 46
7.3.7.2 Procedure . 46
7.3.8 Receiver intermodulation characteristics . 46
7.3.8.1 Initial conditions . 46
7.3.8.2 Procedures . 47
7.3.9 Receiver Adjacent Channel Selectivity (ACS) . 47
7.3.9.1 Initial conditions . 47
7.3.9.2 Procedure for Adjacent Channel Selectivity . 47
7.3.9.3 Procedure for narrow-band blocking . 47
8 Technical requirements specifications for conventional CGC E-UTRA . 48
8.1 Environmental profile . 48
8.2 Conformance requirements . 48
8.2.1 Introduction. 48
8.2.2 Operating band unwanted emissions . 49
8.2.2.0 General . 49
8.2.2.1 Definition . 49
8.2.2.2 Limits . 50
8.2.2.2.0 General . 50
ETSI
6 Draft ETSI EN 302 574-1 V2.1.0 (2016-03)
8.2.2.2.1 Limits for Wide Area CGC . 50
8.2.2.2.2 Limits for Local Area CGC . 50
8.2.2.3 Conformance . 50
8.2.3 Adjacent Channel Leakage power Ratio (ACLR) . 51
8.2.3.1 Definition . 51
8.2.3.2 Limits . 51
8.2.3.3 Conformance . 51
8.2.4 Transmitter spurious emis sions . 51
8.2.4.0 General . 51
8.2.4.1 Definition . 52
8.2.4.2 Limits . 52
8.2.4.2.1 Spurious emissions . 52
8.2.4.2.2 Co-existence with other systems . 52
8.2.4.2.3 Protection of BS receiver . 53
8.2.4.3 Conformance . 53
8.2.5 CGC BS maximum output power . 53
8.2.5.0 General . 53
8.2.5.1 Definition . 53
8.2.5.2 Limit . 54
8.2.5.3 Conformance . 54
8.2.6 Transmitter intermodulation . 54
8.2.6.0 General . 54
8.2.6.1 Definition . 54
8.2.6.2 Limit . 54
8.2.6.3 Conformance . 55
8.2.7 Receiver spurious emissions . 55
8.2.7.0 General . 55
8.2.7.1 Definition . 55
8.2.7.2 Limit . 55
8.2.7.3 Conformance . 55
8.2.8 Blocking characteristics . 56
8.2.8.0 General . 56
8.2.8.1 Definition . 56
8.2.8.2 Limit . 56
8.2.8.3 Conformance . 57
8.2.9 Receiver intermodulation characteristics . 57
8.2.9.0 General . 57
8.2.9.1 Definition . 57
8.2.9.2 Limit . 57
8.2.9.3 Conformance . 58
8.2.10 Adjacent Channel Selectivity (ACS) and narrow-band blocking . 58
8.2.10.0 General . 58
8.2.10.1 Definition . 59
8.2.10.2 Limit . 59
8.2.10.3 Conformance . 60
9 Testing for compliance with technical requirements for conventional CGC E-UTRA . 60
9.1 Environmental conditions for testing . 60
9.2 Interpretation of the measurement results . 61
9.3 Radio test suites . 62
9.3.0 General . 62
9.3.1 Operating band unwanted emissions . 62
9.3.1.0 General . 62
9.3.1.1 Initial conditions . 62
9.3.1.2 Procedure . 62
9.3.2 Adjacent Channel Leakage power Ratio (ACLR) . 63
9.3.2.1 Initial conditions . 63
9.3.2.2 Procedure . 63
9.3.3 Transmitter spurious emis sions . 63
9.3.3.0 General . 63
9.3.3.1 Initial conditions . 63
9.3.3.2 Procedure . 63
ETSI
7 Draft ETSI EN 302 574-1 V2.1.0 (2016-03)
9.3.4 CGC maximum output power . 64
9.3.4.0 General . 64
9.3.4.1 Initial conditions . 64
9.3.4.2 Procedure . 64
9.3.5 Transmitter intermodulation . 64
9.3.5.0 General . 64
9.3.5.1 Initial conditions . 64
9.3.5.2 Procedures . 64
9.3.6 Receiver spurious emissions . 65
9.3.6.0 General . 65
9.3.6.1 Initial conditions . 65
9.3.6.2 Procedure . 65
9.3.7 Blocking characteristics . 66
9.3.7.0 General . 66
9.3.7.1 Initial conditions . 66
9.3.7.2 Procedure . 66
9.3.8 Receiver intermodulation characteristics . 67
9.3.8.0 General . 67
9.3.8.1 Initial conditions . 67
9.3.8.2 Procedures . 67
9.3.9 Adjacent Channel Selectivity (ACS) and narrow-band blocking . 67
9.3.9.0 General . 67
9.3.9.1 Initial conditions . 67
9.3.9.2 Procedure for Adjacent Channel Selectivity . 67
9.3.9.3 Procedure for narrow-band blocking . 68
Annex A (normative): Relationship between the present document and the essential
requirements of Directive 2014/53/EU .
...

HARMONISED EUROPEAN STANDARD
Satellite Earth Stations and Systems (SES);
Harmonised Standard for Mobile Earth Stations (MES)
operating in the 1 980 MHz to 2 010 MHz (earth-to-space) and
2 170 MHz to 2 200 MHz (space-to-earth) frequency bands
covering the essential requirements
of article 3.2 of the Directive 2014/53/EU;
Part 1: Complementary Ground Component (CGC)
for wideband systems
2 ETSI EN 302 574-1 V2.1.1 (2016-06)

Reference
REN/SES-00369
Keywords
broadband, IMT, mobile, satellite
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: [phone]  Fax: [phone]

Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88

Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.

© European Telecommunications Standards Institute 2016.
All rights reserved.
TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.
TM
3GPP and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI
3 ETSI EN 302 574-1 V2.1.1 (2016-06)
Contents
Intellectual Property Rights . 9
Foreword . 9
Modal verbs terminology . 9
Introduction . 10
1 Scope . 11
2 References . 12
2.1 Normative references . 12
2.2 Informative references . 13
3 Definitions, symbols and abbreviations . 13
3.1 Definitions . 13
3.2 Symbols . 14
3.3 Abbreviations . 15
4 Technical requirements specifications for conventional CGC . 16
4.1 Environmental profile . 16
4.2 Conformance requirements . 16
4.2.1 Introduction. 16
4.2.2 Spectrum emission mask . 17
4.2.2.1 Definition . 17
4.2.2.2 Limits . 17
4.2.2.3 Conformance . 18
4.2.3 Adjacent channel leakage power ratio (ACLR) . 18
4.2.3.1 Definition . 18
4.2.3.2 Limits . 18
4.2.3.3 Conformance . 19
4.2.4 Transmitter spurious emis sions . 19
4.2.4.1 Definition . 19
4.2.4.2 Limits . 19
4.2.4.2.1 Spurious emissions . 19
4.2.4.2.2 Coexistence with other systems in the same geographical area. 20
4.2.4.2.3 Protection of UTRA FDD in adjacent frequency band . 20
4.2.4.2.4 Protection of UTRA -TDD . 20
4.2.4.2.5 Protection of UTRA BS . 20
4.2.4.2.6 Protection of the CGC receiver of own or different CGC . 21
4.2.4.3 Conformance . 21
4.2.5 CGC maximum output power . 21
4.2.5.1 Definition . 21
4.2.5.2 Limit . 21
4.2.5.3 Conformance . 22
4.2.6 Transmit inter modulation . 22
4.2.6.1 Definition . 22
4.2.6.2 Limit . 22
4.2.6.3 Conformance . 22
4.2.7 Receiver spurious emissions . 22
4.2.7.1 Definition . 22
4.2.7.2 Limits . 22
4.2.7.3 Conformance . 22
4.2.8 Blocking characteristics . 23
4.2.8.1 Definition . 23
4.2.8.2 Limit . 23
4.2.8.3 Conformance . 23
4.2.9 Receiver inter-modulation characteristics . 23
4.2.9.1 Definition . 23
4.2.9.2 Limit . 23
4.2.9.3 Conformance . 24
ETSI
4 ETSI EN 302 574-1 V2.1.1 (2016-06)
4.2.10 Receiver adjacent selectivity. 24
4.2.10.1 Definition . 24
4.2.10.2 Limit . 24
4.2.10.3 Conformance . 25
5 Testing for compliance with technical requirements for conventional CGC . 26
5.1 Environmental and other conditions for testing . 26
5.2 Interpretation of the measurement results . 26
5.3 Radio test suites . 27
5.3.1 Spectrum emission mask . 27
5.3.1.1 Initial conditions . 27
5.3.1.2 Procedures . 28
5.3.2 Adjacent Channel leakage Power Ratio (ACLR). 28
5.3.2.1 Initial conditions . 28
5.3.2.2 Procedure . 28
5.3.3 Transmitter spurious emis sions . 29
5.3.3.1 Initial conditions . 29
5.3.3.2 Procedure . 29
5.3.4 CGC maximum output power . 29
5.3.4.1 Initial conditions . 29
5.3.4.2 Procedure . 29
5.3.5 Transmit intermodulation . 29
5.3.5.1 Initial conditions . 29
5.3.5.2 Procedures . 30
5.3.6 Receiver spurious emissions . 30
5.3.6.1 Initial conditions . 30
5.3.6.2 Procedure . 30
5.3.7 Blocking characteristics . 31
5.3.7.1 Initial conditions . 31
5.3.7.2 Procedure . 31
5.3.8 Receiver intermodulation characteristics . 31
5.3.8.1 Initial conditions . 31
5.3.8.2 Procedures . 31
5.3.9 Receiver Adjacent Channel Selectivity (ACS) . 32
5.3.9.1 Initial conditions . 32
5.3.9.2 Procedure . 32
6 Technical requirements specifications for Aeronautical CGC . 32
6.1 Environmental profile . 32
6.2 Conformance requirements . 32
6.2.1 Introduction. 32
6.2.2 Spectrum emission mask . 33
6.2.2.1 Definition . 33
6.2.2.2 Limits . 33
6.2.2.3 Conformance . 34
6.2.3 Adjacent channel leakage power ratio (ACLR) . 34
6.2.3.1 Definition . 34
6.2.3.2 Limits . 34
6.2.3.3 Conformance . 34
6.2.4 Transmitter spurious emis sions . 35
6.2.4.1 Definition . 35
6.2.4.2 Limits . 35
6.2.4.2.1 CGC Spurious emissions . 35
6.2.4.2.2 Coexistence with other systems . 35
6.2.4.2.3 Protection of BS receiver . 36
6.2.4.3 Conformance . 36
6.2.5 Aeronautical CGC maximum output power . 37
6.2.5.1 Definition . 37
6.2.5.2 Limit . 37
6.2.5.3 Conformance . 37
6.2.6 Transmit intermodulation . 37
6.2.6.1 Definition . 37
ETSI
5 ETSI EN 302 574-1 V2.1.1 (2016-06)
6.2.6.2 Limit . 37
6.2.6.3 Conformance . 38
6.2.7 Receiver spurious emissions . 38
6.2.7.1 Definition . 38
6.2.7.2 Limits . 38
6.2.7.3 Conformance . 38
6.2.8 Blocking characteristics . 38
6.2.8.1 Definition . 38
6.2.8.2 Limit . 39
6.2.8.3 Conformance . 39
6.2.9 Receiver intermodulation characteristics . 39
6.2.9.1 Definition . 39
6.2.9.2 Limit . 39
6.2.9.3 Conformance . 40
6.2.10 Receiver adjacent Channel selectivity and narrow-band blocking . 40
6.2.10.1 Definition . 40
6.2.10.2 Limit . 41
6.2.10.3 Conformance . 41
7 Testing for compliance with technical requirements for Aeronautical CGC . 42
7.1 Environmental and other conditions for testing . 42
7.2 Interpretation of the measurement results . 42
7.3 Radio test suites . 43
7.3.1 Spectrum emission mask . 43
7.3.1.1 Initial conditions . 43
7.3.1.2 Procedures . 44
7.3.2 Adjacent Channel leakage Power Ratio (ACLR). 44
7.3.2.0 General . 44
7.3.2.1 Initial conditions . 44
7.3.2.2 Procedure . 44
7.3.3 Transmitter spurious emis sions . 45
7.3.3.1 Initial conditions . 45
7.3.3.2 Procedure . 45
7.3.4 Aeronautical CGC maximum output power . 45
7.3.4.1 Initial conditions . 45
7.3.4.2 Procedure . 45
7.3.5 Transmit intermodulation . 45
7.3.5.1 Initial conditions . 45
7.3.5.2 Procedures . 46
7.3.6 Receiver spurious emissions . 46
7.3.6.1 Initial conditions . 46
7.3.6.2 Procedure . 47
7.3.7 Blocking characteristics . 47
7.3.7.1 Initial conditions . 47
7.3.7.2 Procedure . 47
7.3.8 Receiver intermodulation characteristics . 48
7.3.8.1 Initial conditions . 48
7.3.8.2 Procedures . 48
7.3.9 Receiver Adjacent Channel Selectivity (ACS) . 48
7.3.9.1 Initial conditions . 48
7.3.9.2 Procedure for Adjacent Channel Selectivity . 48
7.3.9.3 Procedure for narrow-band blocking . 49
8 Technical requirements specifications for conventional CGC E-UTRA . 49
8.1 Environmental profile . 49
8.2 Conformance requirements . 49
8.2.1 Introduction. 49
8.2.2 Operating band unwanted emissions . 51
8.2.2.0 General . 51
8.2.2.1 Definition . 51
8.2.2.2 Limits . 51
8.2.2.2.0 General . 51
ETSI
6 ETSI EN 302 574-1 V2.1.1 (2016-06)
8.2.2.2.1 Limits for Wide Area CGC . 51
8.2.2.2.2 Limits for Local Area CGC . 52
8.2.2.3 Conformance . 52
8.2.3 Adjacent Channel Leakage power Ratio (ACLR) . 52
8.2.3.1 Definition . 52
8.2.3.2 Limits . 53
8.2.3.3 Conformance . 53
8.2.4 Transmitter spurious emis sions . 53
8.2.4.0 General . 53
8.2.4.1 Definition . 53
8.2.4.2 Limits . 54
8.2.4.2.1 Spurious emissions . 54
8.2.4.2.2 Co-existence with other systems . 54
8.2.4.2.3 Protection of BS receiver . 55
8.2.4.3 Conformance . 55
8.2.5 CGC BS maximum output power . 55
8.2.5.0 General . 55
8.2.5.1 Definition . 55
8.2.5.2 Limit . 55
8.2.5.3 Conformance . 55
8.2.6 Transmitter intermodulation . 56
8.2.6.0 General . 56
8.2.6.1 Definition . 56
8.2.6.2 Limit . 56
8.2.6.3 Conformance . 56
8.2.7 Receiver spurious emissions . 57
8.2.7.0 General . 57
8.2.7.1 Definition . 57
8.2.7.2 Limit . 57
8.2.7.3 Conformance . 57
8.2.8 Blocking characteristics . 57
8.2.8.0 General . 57
8.2.8.1 Definition . 57
8.2.8.2 Limit . 58
8.2.8.3 Conformance . 58
8.2.9 Receiver intermodulation characteristics . 58
8.2.9.0 General . 58
8.2.9.1 Definition . 59
8.2.9.2 Limit . 59
8.2.9.3 Conformance . 60
8.2.10 Adjacent Channel Selectivity (ACS) and narrow-band blocking . 60
8.2.10.0 General . 60
8.2.10.1 Definition . 61
8.2.10.2 Limit . 61
8.2.10.3 Conformance . 62
9 Testing for compliance with technical requirements for conventional CGC E-UTRA . 62
9.1 Environmental conditions for testing . 62
9.2 Interpretation of the measurement results . 63
9.3 Radio test suites . 64
9.3.0 General . 64
9.3.1 Operating band unwanted emissions . 64
9.3.1.0 General . 64
9.3.1.1 Initial conditions . 64
9.3.1.2 Procedure . 65
9.3.2 Adjacent Channel Leakage power Ratio (ACLR) . 65
9.3.2.1 Initial conditions . 65
9.3.2.2 Procedure . 65
9.3.3 Transmitter spurious emis sions . 65
9.3.3.0 General . 65
9.3.3.1 Initial conditions . 65
9.3.3.2 Procedure . 66
ETSI
7 ETSI EN 302 574-1 V2.1.1 (2016-06)
9.3.4 CGC maximum output power . 66
9.3.4.0 General . 66
9.3.4.1 Initial conditions . 66
9.3.4.2 Procedure . 66
9.3.5 Transmitter intermodulation . 66
9.3.5.0 General . 66
9.3.5.1 Initial conditions . 67
9.3.5.2 Procedures . 67
9.3.6 Receiver spurious emissions . 67
9.3.6.0 General . 67
9.3.6.1 Initial conditions . 67
9.3.6.2 Procedure . 68
9.3.7 Blocking characteristics . 68
9.3.7.0 General . 68
9.3.7.1 Initial conditions . 68
9.3.7.2 Procedure . 68
9.3.8 Receiver intermodulation characteristics . 69
9.3.8.0 General . 69
9.3.8.1 Initial conditions . 69
9.3.8.2 Procedures . 69
9.3.9 Adjacent Channel Selectivity (ACS) and narrow-band blocking . 69
9.3.9.0 General . 69
9.3.9.1 Initial conditions . 70
9.3.9.2 Procedure for Adjacent Channel Selectivity . 70
9.3.9.3 Procedure for narrow-band blocking . 70
Annex A (normative): Relationship between the present document and the essential
requirements of Directive 2014/53/EU .
...

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Satellite Earth Stations and Systems (SES) - Harmonised Standard for Satellite Earth Stations (MES) for MSS operating in the 2 GHz frequency band - Part 1: Complementary Ground Component (CGC) for wideband systems covering the essential requirements of article 3.2 of the Directive 2014/53/EU33.060.30Radiorelejni in fiksni satelitski komunikacijski sistemiRadio relay and fixed satellite communications systemsICS:Ta slovenski standard je istoveten z:ETSI EN 302 574-1 V2.1.1 (2016-06)SIST EN 302 574-1 V2.1.1:2016en01-september-2016SIST EN 302 574-1 V2.1.1:2016SLOVENSKI
STANDARD
HARMONISED EUROPEAN STANDARD SIST EN 302 574-1 V2.1.1:2016

ETSI ETSI EN 302 574-1 V2.1.1 (2016-06) 2
Reference REN/SES-00369 Keywords broadband, IMT, mobile, satellite ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: [phone]
Fax: [phone]
Siret N° 348 623 562 00017 - NAF 742 C Association à but non lucratif enregistrée à la Sous-Préfecture de Grasse (06) N° 7803/88
Important notice The present document can be downloaded from: http://www.etsi.org/standards-search The present document may be made available in electronic versions and/or in print. The content of any electronic and/or print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx If you find errors in the present document, please send your comment to one of the following services: https://portal.etsi.org/People/CommiteeSupportStaff.aspx Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm except as authorized by written permission of ETSI. The content of the PDF version shall not be modified without the written authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2016. All rights reserved.
DECTTM, PLUGTESTSTM, UMTSTM and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members. 3GPPTM and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association. SIST EN 302 574-1 V2.1.1:2016

ETSI ETSI EN 302 574-1 V2.1.1 (2016-06) 3 Contents Intellectual Property Rights . 9 Foreword . 9 Modal verbs terminology . 9 Introduction . 10 1 Scope . 11 2 References . 12 2.1 Normative references . 12 2.2 Informative references . 13 3 Definitions, symbols and abbreviations . 13 3.1 Definitions . 13 3.2 Symbols . 14 3.3 Abbreviations . 15 4 Technical requirements specifications for conventional CGC . 16 4.1 Environmental profile . 16 4.2 Conformance requirements . 16 4.2.1 Introduction. 16 4.2.2 Spectrum emission mask . 17 4.2.2.1 Definition . 17 4.2.2.2 Limits . 17 4.2.2.3 Conformance . 18 4.2.3 Adjacent channel leakage power ratio (ACLR) . 18 4.2.3.1 Definition . 18 4.2.3.2 Limits . 18 4.2.3.3 Conformance . 19 4.2.4 Transmitter spurious emissions . 19 4.2.4.1 Definition . 19 4.2.4.2 Limits . 19 4.2.4.2.1 Spurious emissions . 19 4.2.4.2.2 Coexistence with other systems in the same geographical area. 20 4.2.4.2.3 Protection of UTRA FDD in adjacent frequency band . 20 4.2.4.2.4 Protection of UTRA -TDD . 20 4.2.4.2.5 Protection of UTRA BS . 20 4.2.4.2.6 Protection of the CGC receiver of own or different CGC . 21 4.2.4.3 Conformance . 21 4.2.5 CGC maximum output power . 21 4.2.5.1 Definition . 21 4.2.5.2 Limit . 21 4.2.5.3 Conformance . 22 4.2.6 Transmit inter modulation . 22 4.2.6.1 Definition . 22 4.2.6.2 Limit . 22 4.2.6.3 Conformance . 22 4.2.7 Receiver spurious emissions . 22 4.2.7.1 Definition . 22 4.2.7.2 Limits . 22 4.2.7.3 Conformance . 22 4.2.8 Blocking characteristics . 23 4.2.8.1 Definition . 23 4.2.8.2 Limit . 23 4.2.8.3 Conformance . 23 4.2.9 Receiver inter-modulation characteristics . 23 4.2.9.1 Definition . 23 4.2.9.2 Limit . 23 4.2.9.3 Conformance . 24 SIST EN 302 574-1 V2.1.1:2016

ETSI ETSI EN 302 574-1 V2.1.1 (2016-06) 4 4.2.10 Receiver adjacent selectivity. 24 4.2.10.1 Definition . 24 4.2.10.2 Limit . 24 4.2.10.3 Conformance . 25 5 Testing for compliance with technical requirements for conventional CGC . 26 5.1 Environmental and other conditions for testing . 26 5.2 Interpretation of the measurement results . 26 5.3 Radio test suites . 27 5.3.1 Spectrum emission mask . 27 5.3.1.1 Initial conditions . 27 5.3.1.2 Procedures . 28 5.3.2 Adjacent Channel leakage Power Ratio (ACLR). 28 5.3.2.1 Initial conditions . 28 5.3.2.2 Procedure . 28 5.3.3 Transmitter spurious emissions . 29 5.3.3.1 Initial conditions . 29 5.3.3.2 Procedure . 29 5.3.4 CGC maximum output power . 29 5.3.4.1 Initial conditions . 29 5.3.4.2 Procedure . 29 5.3.5 Transmit intermodulation . 29 5.3.5.1 Initial conditions . 29 5.3.5.2 Procedures . 30 5.3.6 Receiver spurious emissions . 30 5.3.6.1 Initial conditions . 30 5.3.6.2 Procedure . 30 5.3.7 Blocking characteristics . 31 5.3.7.1 Initial conditions . 31 5.3.7.2 Procedure . 31 5.3.8 Receiver intermodulation characteristics . 31 5.3.8.1 Initial conditions . 31 5.3.8.2 Procedures . 31 5.3.9 Receiver Adjacent Channel Selectivity (ACS) . 32 5.3.9.1 Initial conditions . 32 5.3.9.2 Procedure . 32 6 Technical requirements specifications for Aeronautical CGC . 32 6.1 Environmental profile . 32 6.2 Conformance requirements . 32 6.2.1 Introduction. 32 6.2.2 Spectrum emission mask . 33 6.2.2.1 Definition . 33 6.2.2.2 Limits . 33 6.2.2.3 Conformance . 34 6.2.3 Adjacent channel leakage power ratio (ACLR) . 34 6.2.3.1 Definition . 34 6.2.3.2 Limits . 34 6.2.3.3 Conformance . 34 6.2.4 Transmitter spurious emissions . 35 6.2.4.1 Definition . 35 6.2.4.2 Limits . 35 6.2.4.2.1 CGC Spurious emissions . 35 6.2.4.2.2 Coexistence with other systems . 35 6.2.4.2.3 Protection of BS receiver . 36 6.2.4.3 Conformance . 36 6.2.5 Aeronautical CGC maximum output power . 37 6.2.5.1 Definition . 37 6.2.5.2 Limit . 37 6.2.5.3 Conformance . 37 6.2.6 Transmit intermodulation . 37 6.2.6.1 Definition . 37 SIST EN 302 574-1 V2.1.1:2016

ETSI ETSI EN 302 574-1 V2.1.1 (2016-06) 5 6.2.6.2 Limit . 37 6.2.6.3 Conformance . 38 6.2.7 Receiver spurious emissions . 38 6.2.7.1 Definition . 38 6.2.7.2 Limits . 38 6.2.7.3 Conformance . 38 6.2.8 Blocking characteristics . 38 6.2.8.1 Definition . 38 6.2.8.2 Limit . 39 6.2.8.3 Conformance . 39 6.2.9 Receiver intermodulation characteristics . 39 6.2.9.1 Definition . 39 6.2.9.2 Limit . 39 6.2.9.3 Conformance . 40 6.2.10 Receiver adjacent Channel selectivity and narrow-band blocking . 40 6.2.10.1 Definition . 40 6.2.10.2 Limit . 41 6.2.10.3 Conformance . 41 7 Testing for compliance with technical requirements for Aeronautical CGC . 42 7.1 Environmental and other conditions for testing . 42 7.2 Interpretation of the measurement results . 42 7.3 Radio test suites . 43 7.3.1 Spectrum emission mask . 43 7.3.1.1 Initial conditions . 43 7.3.1.2 Procedures . 44 7.3.2 Adjacent Channel leakage Power Ratio (ACLR). 44 7.3.2.0 General . 44 7.3.2.1 Initial conditions . 44 7.3.2.2 Procedure . 44 7.3.3 Transmitter spurious emissions . 45 7.3.3.1 Initial conditions . 45 7.3.3.2 Procedure . 45 7.3.4 Aeronautical CGC maximum output power . 45 7.3.4.1 Initial conditions . 45 7.3.4.2 Procedure . 45 7.3.5 Transmit intermodulation . 45 7.3.5.1 Initial conditions . 45 7.3.5.2 Procedures . 46 7.3.6 Receiver spurious emissions . 46 7.3.6.1 Initial conditions . 46 7.3.6.2 Procedure . 47 7.3.7 Blocking characteristics . 47 7.3.7.1 Initial conditions . 47 7.3.7.2 Procedure . 47 7.3.8 Receiver intermodulation characteristics . 48 7.3.8.1 Initial conditions . 48 7.3.8.2 Procedures . 48 7.3.9 Receiver Adjacent Channel Selectivity (ACS) . 48 7.3.9.1 Initial conditions . 48 7.3.9.2 Procedure for Adjacent Channel Selectivity . 48 7.3.9.3 Procedure for narrow-band blocking . 49 8 Technical requirements specifications for conventional CGC E-UTRA . 49 8.1 Environmental profile . 49 8.2 Conformance requirements . 49 8.2.1 Introduction. 49 8.2.2 Operating band unwanted emissions . 51 8.2.2.0 General . 51 8.2.2.1 Definition . 51 8.2.2.2 Limits . 51 8.2.2.2.0 General . 51 SIST EN 302 574-1 V2.1.1:2016

ETSI ETSI EN 302 574-1 V2.1.1 (2016-06) 6 8.2.2.2.1 Limits for Wide Area CGC . 51 8.2.2.2.2 Limits for Local Area CGC . 52 8.2.2.3 Conformance . 52 8.2.3 Adjacent Channel Leakage power Ratio (ACLR) . 52 8.2.3.1 Definition . 52 8.2.3.2 Limits . 53 8.2.3.3 Conformance . 53 8.2.4 Transmitter spurious emissions . 53 8.2.4.0 General . 53 8.2.4.1 Definition . 53 8.2.4.2 Limits . 54 8.2.4.2.1 Spurious emissions . 54 8.2.4.2.2 Co-existence with other systems . 54 8.2.4.2.3 Protection of BS receiver . 55 8.2.4.3 Conformance . 55 8.2.5 CGC BS maximum output power . 55 8.2.5.0 General . 55 8.2.5.1 Definition . 55 8.2.5.2 Limit . 55 8.2.5.3 Conformance . 55 8.2.6 Transmitter intermodulation . 56 8.2.6.0 General . 56 8.2.6.1 Definition . 56 8.2.6.2 Limit . 56 8.2.6.3 Conformance . 56 8.2.7 Receiver spurious emissions . 57 8.2.7.0 General . 57 8.2.7.1 Definition . 57 8.2.7.2 Limit . 57 8.2.7.3 Conformance . 57 8.2.8 Blocking characteristics . 57 8.2.8.0 General . 57 8.2.8.1 Definition . 57 8.2.8.2 Limit . 58 8.2.8.3 Conformance . 58 8.2.9 Receiver intermodulation characteristics . 58 8.2.9.0 General . 58 8.2.9.1 Definition . 59 8.2.9.2 Limit . 59 8.2.9.3 Conformance . 60 8.2.10 Adjacent Channel Selectivity (ACS) and narrow-band blocking . 60 8.2.10.0 General . 60 8.2.10.1 Definition . 61 8.2.10.2 Limit . 61 8.2.10.3 Conformance . 62 9 Testing for compliance with technical requirements for conventional CGC E-UTRA . 62 9.1 Environmental conditions for testing . 62 9.2 Interpretation of the measurement results . 63 9.3 Radio test suites . 64 9.3.0 General . 64 9.3.1 Operating band unwanted emissions . 64 9.3.1.0 General . 64 9.3.1.1 Initial conditions . 64 9.3.1.2 Procedure . 65 9.3.2 Adjacent Channel Leakage power Ratio (ACLR) . 65 9.3.2.1 Initial conditions . 65 9.3.2.2 Procedure . 65 9.3.3 Transmitter spurious emissions . 65 9.3.3.0 General . 65 9.3.3.1 Initial conditions . 65 9.3.3.2 Procedure . 66 SIST EN 302 574-1 V2.1.1:2016

ETSI ETSI EN 302 574-1 V2.1.1 (2016-06) 7 9.3.4 CGC maximum output power . 66 9.3.4.0 General . 66 9.3.4.1 Initial conditions . 66 9.3.4.2 Procedure . 66 9.3.5 Transmitter intermodulation . 66 9.3.5.0 General . 66 9.3.5.1 Initial conditions . 67 9.3.5.2 Procedures . 67 9.3.6 Receiver spurious emissions . 67 9.3.6.0 General . 67 9.3.6.1 Initial conditions . 67 9.3.6.2 Procedure . 68 9.3.7 Blocking characteristics . 68 9.3.7.0 General . 68 9.3.7.1 Initial conditions . 68 9.3.7.2 Procedure . 68 9.3.8 Receiver intermodulation characteristics . 69 9.3.8.0 General . 69 9.3.8.1 Initial conditions . 69 9.3.8.2 Procedures . 69 9.3.9 Adjacent Channel Selectivity (ACS) and narrow-band blocking . 69 9.3.9.0 General . 69 9.3.9.1 Initial conditions . 70 9.3.9.2 Procedure for Adjacent Channel Selectivity . 70 9.3.9.3 Procedure for narrow-band blocking .
...