ETSI EN 300 338-6 V1.2.1 (2020-06)
Technical characteristics and methods of measurement for equipment for generation, transmission and reception of Digital Selective Calling (DSC) in the maritime MF, MF/HF and/or VHF mobile service; Part 6: Class M DSC
Technical characteristics and methods of measurement for equipment for generation, transmission and reception of Digital Selective Calling (DSC) in the maritime MF, MF/HF and/or VHF mobile service; Part 6: Class M DSC
REN/ERM-TGMAR-601
Tehnične karakteristike in merilne metode za naprave, ki generirajo, oddajajo in sprejemajo digitalni selektivni klic (DSC) v pomorski mobilni storitvi, ki deluje v območju MF, MF/HF oziroma VHF - 6. del: Digitalni selektivni klic razreda M
General Information
Buy Standard
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 300 338-6 V1.2.1:2020
01-september-2020
Tehnične karakteristike in merilne metode za naprave, ki generirajo, oddajajo in
sprejemajo digitalni selektivni klic (DSC) v pomorski mobilni storitvi, ki deluje v
območju MF, MF/HF oziroma VHF - 6. del: Digitalni selektivni klic razreda M
Technical characteristics and methods of measurement for equipment for generation,
transmission and reception of Digital Selective Calling (DSC) in the maritime MF, MF/HF
and/or VHF mobile service - Part 6: Class M DSC
Ta slovenski standard je istoveten z: ETSI EN 300 338-6 V1.2.1 (2020-06)
ICS:
33.060.20 Sprejemna in oddajna Receiving and transmitting
oprema equipment
47.020.70 Navigacijska in krmilna Navigation and control
oprema equipment
SIST EN 300 338-6 V1.2.1:2020 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 300 338-6 V1.2.1:2020
---------------------- Page: 2 ----------------------
SIST EN 300 338-6 V1.2.1:2020
ETSI EN 300 338-6 V1.2.1 (2020-06)
EUROPEAN STANDARD
Technical characteristics and methods of measurement
for equipment for generation, transmission
and reception of Digital Selective Calling (DSC)
in the maritime MF, MF/HF and/or VHF mobile service;
Part 6: Class M DSC
---------------------- Page: 3 ----------------------
SIST EN 300 338-6 V1.2.1:2020
2 ETSI EN 300 338-6 V1.2.1 (2020-06)
Reference
REN/ERM-TGMAR-601
Keywords
DSC, GMDSS, maritime, radio, SAR
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI
deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© ETSI 2020.
All rights reserved.
DECT™, PLUGTESTS™, UMTS™ and the ETSI logo are trademarks of ETSI registered for the benefit of its Members.
3GPP™ and LTE™ are trademarks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
oneM2M™ logo is a trademark of ETSI registered for the benefit of its Members and
of the oneM2M Partners.
®
GSM and the GSM logo are trademarks registered and owned by the GSM Association.
ETSI
---------------------- Page: 4 ----------------------
SIST EN 300 338-6 V1.2.1:2020
3 ETSI EN 300 338-6 V1.2.1 (2020-06)
Contents
Intellectual Property Rights . 4
Foreword . 4
Modal verbs terminology . 4
1 Scope . 5
2 References . 5
2.1 Normative references . 5
2.2 Informative references . 5
3 Definition of terms, symbols and abbreviations . 6
3.1 Terms . 6
3.2 Symbols . 6
3.3 Abbreviations . 7
4 General requirements . 7
4.1 General . 7
4.2 Frequency of operation . 7
4.3 Class of emission . 7
4.4 Controls . 8
4.5 Indicators . 8
4.5.0 General . 8
4.5.1 Audible indicators . 8
4.5.2 Visual Indicators . 8
4.6 Labelling. 8
4.7 Instructions . 9
4.8 Self ID . 9
4.9 Own vessel MMSI . 9
4.10 Battery requirement . 9
5 DSC Operation . 10
5.1 Listen Before Talk (LBT) Protocol . 10
5.1.0 General . 10
5.1.1 Active Mode Wait Period Calculation . 10
5.1.2 Test Mode Wait Period Calculation . 10
5.2 DSC messages . 10
5.2.1 Active mode . 10
5.2.1.0 General . 10
5.2.1.1 Closed loop operation . 10
5.2.1.2 Open loop operation . 11
5.2.1.3 Distress self-cancel. 11
5.2.2 Test mode. 12
5.3 Action on receipt of acknowledgment messages to alerts . 12
6 Internal electronic position fixing device . 12
Annex A (informative): Change History . 13
History . 14
ETSI
---------------------- Page: 5 ----------------------
SIST EN 300 338-6 V1.2.1:2020
4 ETSI EN 300 338-6 V1.2.1 (2020-06)
Intellectual Property Rights
Essential patents
IPRs essential or potentially essential to normative deliverables may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (https://ipr.etsi.org/).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Trademarks
The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners.
ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no
right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does
not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks.
Foreword
This European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic compatibility and
Radio spectrum Matters (ERM).
The present document is part 6 of a multi-part deliverable. Full details of the entire series can be found in part 1 [i.1].
National transposition dates
Date of adoption of this EN: 29 May 2020
Date of latest announcement of this EN (doa): 31 August 2020
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 28 February 2021
Date of withdrawal of any conflicting National Standard (dow): 28 February 2022
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
ETSI
---------------------- Page: 6 ----------------------
SIST EN 300 338-6 V1.2.1:2020
5 ETSI EN 300 338-6 V1.2.1 (2020-06)
1 Scope
The present document states the minimum requirements for devices using Digital Selective Calling (DSC) Class M, for
Man Overboard (MOB). The present document defines the requirements for equipment that uses DSC alerting and
signalling in the maritime mobile bands and particularly the GMDSS distress and safety channels. Such equipment is
not intended to provide any subsequent communications or telephony facilities.
The present document is part 6 of a multi-part deliverable that covers the channel access rules and technical
requirements applicable to these devices.
2 References
2.1 Normative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
https://docbox.etsi.org/Reference/.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are necessary for the application of the present document.
[1] Recommendation ITU-R M.493-15 (01/2019): "Digital selective-calling system for use in the
maritime mobile service".
[2] ETSI EN 303 098: "Maritime low power personal locating devices employing AIS; Harmonised
Standard for access to radio spectrum".
[3] Recommendation ITU-R M.585-8: "Assignment and use of identities in the maritime mobile
service".
[4] Recommendation ITU-R M.821-1: "Optional expansion of the digital selective-calling system for
use in the maritime mobile service".
[5] CENELEC EN 61108-1: "Maritime navigation and radiocommunication equipment and systems -
Global navigation satellite systems (GNSS) - Part 1: Global positioning system (GPS) - Receiver
equipment - Performance standards, methods of testing and required test results".
[6] CENELEC EN 61108-2: "Maritime navigation and radiocommunication equipment and systems -
Global navigation satellite systems (GNSS) - Part 2: Global navigation satellite system
(GLONASS) - Receiver equipment - Performance standards, methods of testing and required test
results".
[7] CENELEC EN 61108-3: "Maritime navigation and radiocommunication equipment and systems -
Global navigation satellite systems (GNSS) - Part 3: Galileo receiver equipment - Performance
requirements, methods of testing and required test results".
2.2 Informative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
ETSI
---------------------- Page: 7 ----------------------
SIST EN 300 338-6 V1.2.1:2020
6 ETSI EN 300 338-6 V1.2.1 (2020-06)
The following referenced documents are not necessary for the application of the present document but they assist the
user with regard to a particular subject area.
[i.1] ETSI EN 300 338-1: "Technical characteristics and methods of measurement for equipment for
generation, transmission and reception of Digital Selective Calling (DSC) in the maritime MF,
MF/HF and/or VHF mobile service; Part 1: Common requirements".
3 Definition of terms, symbols and abbreviations
3.1 Terms
For the purposes of the present document, the terms given in ETSI EN 300 338-1 [i.1] and the following apply:
acknowledged: automated procedure which indicates that the objective of the initial DSC message has been achieved
activation: initial triggering of the MoB device i.e. both parts of the two step procedure are performed
active mode: activated mode, transmitting in an emergency situation
class M: specific class of DSC functionality for use by man overboard devices
closed loop: individual transmission to own vessel
default: value selected or an action taken by the equipment software in the absence of any operator input
distress alert: name given to the single distress DSC message with the format symbol 112
distress DSC message: DSC message or acknowledgement containing the distress information
distress information: symbols within a DSC message describing a distress situation consisting of the MMSI of the
vessel in distress, the nature of distress, the position of the vessel in distress, the UTC time of that position and the mode
of subsequent communication
factory default: default value that is set by the manufacturer such that the field or behaviour is defined prior to any
operator intervention
information characters: set of symbols in a DSC message that contains the items of interest for the recipient and is
used to compute the ECC symbol that terminates the message
non distress DSC message: DSC messages or acknowledgements that do not have the format specifier or category of
"distress"
open loop: transmitting to all ships (broadcast) 'using All ships call types'
symbol (as part of the DSC sentence): 7 binary bits of a 10 bit DSC word that have the information content
test mode: self-testing mode using an individual test call to own vessel
word (as part of the DSC sentence): 10 binary bits that make up the coded entities of a transmitted DSC message
NOTE: The 10 bits consist of a 7 bit "symbol" that gives the information content and 3 bit error check that gives
the number of 0 binary bits in the 7 bit symbol.
3.2 Symbols
Void.
ETSI
---------------------- Page: 8 ----------------------
SIST EN 300 338-6 V1.2.1:2020
7 ETSI EN 300 338-6 V1.2.1 (2020-06)
3.3 Abbreviations
For the purposes of the present document, the following abbreviations apply:
AIS Automatic Identification System
CIRM Comité
...
ETSI EN 300 338-6 V1.2.1 (2020-06)
EUROPEAN STANDARD
Technical characteristics and methods of measurement
for equipment for generation, transmission
and reception of Digital Selective Calling (DSC)
in the maritime MF, MF/HF and/or VHF mobile service;
Part 6: Class M DSC
---------------------- Page: 1 ----------------------
2 ETSI EN 300 338-6 V1.2.1 (2020-06)
Reference
REN/ERM-TGMAR-601
Keywords
DSC, GMDSS, maritime, radio, SAR
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI
deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© ETSI 2020.
All rights reserved.
DECT™, PLUGTESTS™, UMTS™ and the ETSI logo are trademarks of ETSI registered for the benefit of its Members.
3GPP™ and LTE™ are trademarks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
oneM2M™ logo is a trademark of ETSI registered for the benefit of its Members and
of the oneM2M Partners.
®
GSM and the GSM logo are trademarks registered and owned by the GSM Association.
ETSI
---------------------- Page: 2 ----------------------
3 ETSI EN 300 338-6 V1.2.1 (2020-06)
Contents
Intellectual Property Rights . 4
Foreword . 4
Modal verbs terminology . 4
1 Scope . 5
2 References . 5
2.1 Normative references . 5
2.2 Informative references . 5
3 Definition of terms, symbols and abbreviations . 6
3.1 Terms . 6
3.2 Symbols . 6
3.3 Abbreviations . 7
4 General requirements . 7
4.1 General . 7
4.2 Frequency of operation . 7
4.3 Class of emission . 7
4.4 Controls . 8
4.5 Indicators . 8
4.5.0 General . 8
4.5.1 Audible indicators . 8
4.5.2 Visual Indicators . 8
4.6 Labelling. 8
4.7 Instructions . 9
4.8 Self ID . 9
4.9 Own vessel MMSI . 9
4.10 Battery requirement . 9
5 DSC Operation . 10
5.1 Listen Before Talk (LBT) Protocol . 10
5.1.0 General . 10
5.1.1 Active Mode Wait Period Calculation . 10
5.1.2 Test Mode Wait Period Calculation . 10
5.2 DSC messages . 10
5.2.1 Active mode . 10
5.2.1.0 General . 10
5.2.1.1 Closed loop operation . 10
5.2.1.2 Open loop operation . 11
5.2.1.3 Distress self-cancel. 11
5.2.2 Test mode. 12
5.3 Action on receipt of acknowledgment messages to alerts . 12
6 Internal electronic position fixing device . 12
Annex A (informative): Change History . 13
History . 14
ETSI
---------------------- Page: 3 ----------------------
4 ETSI EN 300 338-6 V1.2.1 (2020-06)
Intellectual Property Rights
Essential patents
IPRs essential or potentially essential to normative deliverables may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (https://ipr.etsi.org/).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Trademarks
The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners.
ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no
right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does
not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks.
Foreword
This European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic compatibility and
Radio spectrum Matters (ERM).
The present document is part 6 of a multi-part deliverable. Full details of the entire series can be found in part 1 [i.1].
National transposition dates
Date of adoption of this EN: 29 May 2020
Date of latest announcement of this EN (doa): 31 August 2020
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 28 February 2021
Date of withdrawal of any conflicting National Standard (dow): 28 February 2022
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
ETSI
---------------------- Page: 4 ----------------------
5 ETSI EN 300 338-6 V1.2.1 (2020-06)
1 Scope
The present document states the minimum requirements for devices using Digital Selective Calling (DSC) Class M, for
Man Overboard (MOB). The present document defines the requirements for equipment that uses DSC alerting and
signalling in the maritime mobile bands and particularly the GMDSS distress and safety channels. Such equipment is
not intended to provide any subsequent communications or telephony facilities.
The present document is part 6 of a multi-part deliverable that covers the channel access rules and technical
requirements applicable to these devices.
2 References
2.1 Normative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
https://docbox.etsi.org/Reference/.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are necessary for the application of the present document.
[1] Recommendation ITU-R M.493-15 (01/2019): "Digital selective-calling system for use in the
maritime mobile service".
[2] ETSI EN 303 098: "Maritime low power personal locating devices employing AIS; Harmonised
Standard for access to radio spectrum".
[3] Recommendation ITU-R M.585-8: "Assignment and use of identities in the maritime mobile
service".
[4] Recommendation ITU-R M.821-1: "Optional expansion of the digital selective-calling system for
use in the maritime mobile service".
[5] CENELEC EN 61108-1: "Maritime navigation and radiocommunication equipment and systems -
Global navigation satellite systems (GNSS) - Part 1: Global positioning system (GPS) - Receiver
equipment - Performance standards, methods of testing and required test results".
[6] CENELEC EN 61108-2: "Maritime navigation and radiocommunication equipment and systems -
Global navigation satellite systems (GNSS) - Part 2: Global navigation satellite system
(GLONASS) - Receiver equipment - Performance standards, methods of testing and required test
results".
[7] CENELEC EN 61108-3: "Maritime navigation and radiocommunication equipment and systems -
Global navigation satellite systems (GNSS) - Part 3: Galileo receiver equipment - Performance
requirements, methods of testing and required test results".
2.2 Informative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
ETSI
---------------------- Page: 5 ----------------------
6 ETSI EN 300 338-6 V1.2.1 (2020-06)
The following referenced documents are not necessary for the application of the present document but they assist the
user with regard to a particular subject area.
[i.1] ETSI EN 300 338-1: "Technical characteristics and methods of measurement for equipment for
generation, transmission and reception of Digital Selective Calling (DSC) in the maritime MF,
MF/HF and/or VHF mobile service; Part 1: Common requirements".
3 Definition of terms, symbols and abbreviations
3.1 Terms
For the purposes of the present document, the terms given in ETSI EN 300 338-1 [i.1] and the following apply:
acknowledged: automated procedure which indicates that the objective of the initial DSC message has been achieved
activation: initial triggering of the MoB device i.e. both parts of the two step procedure are performed
active mode: activated mode, transmitting in an emergency situation
class M: specific class of DSC functionality for use by man overboard devices
closed loop: individual transmission to own vessel
default: value selected or an action taken by the equipment software in the absence of any operator input
distress alert: name given to the single distress DSC message with the format symbol 112
distress DSC message: DSC message or acknowledgement containing the distress information
distress information: symbols within a DSC message describing a distress situation consisting of the MMSI of the
vessel in distress, the nature of distress, the position of the vessel in distress, the UTC time of that position and the mode
of subsequent communication
factory default: default value that is set by the manufacturer such that the field or behaviour is defined prior to any
operator intervention
information characters: set of symbols in a DSC message that contains the items of interest for the recipient and is
used to compute the ECC symbol that terminates the message
non distress DSC message: DSC messages or acknowledgements that do not have the format specifier or category of
"distress"
open loop: transmitting to all ships (broadcast) 'using All ships call types'
symbol (as part of the DSC sentence): 7 binary bits of a 10 bit DSC word that have the information content
test mode: self-testing mode using an individual test call to own vessel
word (as part of the DSC sentence): 10 binary bits that make up the coded entities of a transmitted DSC message
NOTE: The 10 bits consist of a 7 bit "symbol" that gives the information content and 3 bit error check that gives
the number of 0 binary bits in the 7 bit symbol.
3.2 Symbols
Void.
ETSI
---------------------- Page: 6 ----------------------
7 ETSI EN 300 338-6 V1.2.1 (2020-06)
3.3 Abbreviations
For the purposes of the present document, the following abbreviations apply:
AIS Automatic Identification System
CIRM Comité International Radio-Maritime
DSC Digital Selective Calling
ECC Error Check Character
GMDSS Global Maritime Distress and Safety System
GMSK Gaussian Minimum Shift Keying
GNSS Global Navigation Satellite System
GPS Global Positioning System
HF High Frequency
ID IDentity
ITU International Telecommunications Union
ITU-R ITU - Radiocommunications sector
LBT Listen Before Talk
MF Medium Frequency
MMSI Maritime Mobile Service Identity
MOB Man Overboard
PM Phase Modulation
UTC Universal Time Co-ordinated
V
...
Final draft ETSI EN 300 338-6 V1.2.1 (2020-03)
EUROPEAN STANDARD
Technical characteristics and methods of measurement
for equipment for generation, transmission
and reception of Digital Selective Calling (DSC)
in the maritime MF, MF/HF and/or VHF mobile service;
Part 6: Class M DSC
---------------------- Page: 1 ----------------------
2 Final draft ETSI EN 300 338-6 V1.2.1 (2020-03)
Reference
REN/ERM-TGMAR-601
Keywords
DSC, GMDSS, maritime, radio, SAR
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI
deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© ETSI 2020.
All rights reserved.
DECT™, PLUGTESTS™, UMTS™ and the ETSI logo are trademarks of ETSI registered for the benefit of its Members.
3GPP™ and LTE™ are trademarks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
oneM2M™ logo is a trademark of ETSI registered for the benefit of its Members and
of the oneM2M Partners.
®
GSM and the GSM logo are trademarks registered and owned by the GSM Association.
ETSI
---------------------- Page: 2 ----------------------
3 Final draft ETSI EN 300 338-6 V1.2.1 (2020-03)
Contents
Intellectual Property Rights . 4
Foreword . 4
Modal verbs terminology . 4
1 Scope . 5
2 References . 5
2.1 Normative references . 5
2.2 Informative references . 5
3 Definition of terms, symbols and abbreviations . 6
3.1 Terms . 6
3.2 Symbols . 6
3.3 Abbreviations . 7
4 General requirements . 7
4.1 General . 7
4.2 Frequency of operation . 7
4.3 Class of emission . 7
4.4 Controls . 8
4.5 Indicators . 8
4.5.0 General . 8
4.5.1 Audible indicators . 8
4.5.2 Visual Indicators . 8
4.6 Labelling. 8
4.7 Instructions . 9
4.8 Self ID . 9
4.9 Own vessel MMSI . 9
4.10 Battery requirement . 9
5 DSC Operation . 10
5.1 Listen Before Talk (LBT) Protocol . 10
5.1.0 General . 10
5.1.1 Active Mode Wait Period Calculation . 10
5.1.2 Test Mode Wait Period Calculation . 10
5.2 DSC messages . 10
5.2.1 Active mode . 10
5.2.1.0 General . 10
5.2.1.1 Closed loop operation . 10
5.2.1.2 Open loop operation . 11
5.2.1.3 Distress self-cancel. 11
5.2.2 Test mode. 12
5.3 Action on receipt of acknowledgment messages to alerts . 12
6 Internal electronic position fixing device . 12
Annex A (informative): Change History . 13
History . 14
ETSI
---------------------- Page: 3 ----------------------
4 Final draft ETSI EN 300 338-6 V1.2.1 (2020-03)
Intellectual Property Rights
Essential patents
IPRs essential or potentially essential to normative deliverables may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (https://ipr.etsi.org/).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Trademarks
The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners.
ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no
right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does
not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks.
Foreword
This final draft European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic
compatibility and Radio spectrum Matters (ERM), and is now submitted for the Vote phase of the ETSI standards EN
Approval Procedure.
The present document is part 6 of a multi-part deliverable. Full details of the entire series can be found in part 1 [i.1].
Proposed national transposition dates
Date of latest announcement of this EN (doa): 3 months after ETSI publication
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 6 months after doa
Date of withdrawal of any conflicting National Standard (dow): 18 months after doa
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
ETSI
---------------------- Page: 4 ----------------------
5 Final draft ETSI EN 300 338-6 V1.2.1 (2020-03)
1 Scope
The present document states the minimum requirements for devices using Digital Selective Calling (DSC) Class M, for
Man Overboard (MOB). The present document defines the requirements for equipment that uses DSC alerting and
signalling in the maritime mobile bands and particularly the GMDSS distress and safety channels. Such equipment is
not intended to provide any subsequent communications or telephony facilities.
The present document is part 6 of a multi-part deliverable that covers the channel access rules and technical
requirements applicable to these devices.
2 References
2.1 Normative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
https://docbox.etsi.org/Reference/.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are necessary for the application of the present document.
[1] Recommendation ITU-R M.493-15 (01/2019): "Digital selective-calling system for use in the
maritime mobile service".
[2] ETSI EN 303 098: "Maritime low power personal locating devices employing AIS; Harmonised
Standard for access to radio spectrum".
[3] Recommendation ITU-R M.585-8: "Assignment and use of identities in the maritime mobile
service".
[4] Recommendation ITU-R M.821-1: "Optional expansion of the digital selective-calling system for
use in the maritime mobile service".
[5] CENELEC EN 61108-1: "Maritime navigation and radiocommunication equipment and systems -
Global navigation satellite systems (GNSS) - Part 1: Global positioning system (GPS) - Receiver
equipment - Performance standards, methods of testing and required test results".
[6] CENELEC EN 61108-2: "Maritime navigation and radiocommunication equipment and systems -
Global navigation satellite systems (GNSS) - Part 2: Global navigation satellite system
(GLONASS) - Receiver equipment - Performance standards, methods of testing and required test
results".
[7] CENELEC EN 61108-3: "Maritime navigation and radiocommunication equipment and systems -
Global navigation satellite systems (GNSS) - Part 3: Galileo receiver equipment - Performance
requirements, methods of testing and required test results".
2.2 Informative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
ETSI
---------------------- Page: 5 ----------------------
6 Final draft ETSI EN 300 338-6 V1.2.1 (2020-03)
The following referenced documents are not necessary for the application of the present document but they assist the
user with regard to a particular subject area.
[i.1] ETSI EN 300 338-1: "Technical characteristics and methods of measurement for equipment for
generation, transmission and reception of Digital Selective Calling (DSC) in the maritime MF,
MF/HF and/or VHF mobile service; Part 1: Common requirements".
3 Definition of terms, symbols and abbreviations
3.1 Terms
For the purposes of the present document, the terms given in ETSI EN 300 338-1 [i.1] and the following apply:
acknowledged: automated procedure which indicates that the objective of the initial DSC message has been achieved
activation: initial triggering of the MoB device i.e. both parts of the two step procedure are performed
active mode: activated mode, transmitting in an emergency situation
class M: specific class of DSC functionality for use by man overboard devices
closed loop: individual transmission to own vessel
default: value selected or an action taken by the equipment software in the absence of any operator input
distress alert: name given to the single distress DSC message with the format symbol 112
distress DSC message: DSC message or acknowledgement containing the distress information
distress information: symbols within a DSC message describing a distress situation consisting of the MMSI of the
vessel in distress, the nature of distress, the position of the vessel in distress, the UTC time of that position and the mode
of subsequent communication
factory default: default value that is set by the manufacturer such that the field or behaviour is defined prior to any
operator intervention
information characters: set of symbols in a DSC message that contains the items of interest for the recipient and is
used to compute the ECC symbol that terminates the message
non distress DSC message: DSC messages or acknowledgements that do not have the format specifier or category of
"distress"
open loop: transmitting to all ships (broadcast) 'using All ships call types'
symbol (as part of the DSC sentence): 7 binary bits of a 10 bit DSC word that have the information content
test mode: self-testing mode using an individual test call to own vessel
word (as part of the DSC sentence): 10 binary bits that make up the coded entities of a transmitted DSC message
NOTE: The 10 bits consist of a 7 bit "symbol" that gives the information content and 3 bit error check that gives
the number of 0 binary bits in the 7 bit symbol.
3.2 Symbols
Void.
ETSI
---------------------- Page: 6 ----------------------
7 Final draft ETSI EN 300 338-6 V1.2.1 (2020-03)
3.3 Abbreviations
For the purposes of the present document, the following abbreviations apply:
AIS Automatic Identification System
CIRM Comité International Radio-Maritime
DSC Digital Selective Calling
ECC Error Check Character
GMDSS Global Maritime Distress and Safety System
GMSK Gaussian Minimum Shift Keying
GNSS Global Navigation Satellite System
GPS Global Positioning System
HF High Frequency
ID IDentity
ITU International Telecommunications Union
ITU-R ITU - Radiocommunications sector
LBT Listen Before Talk
MF Medium Frequency
MMSI Maritime Mobile Service Identity
MOB Man Overboard
...
Draft ETSI EN 300 338-6 V1.2.0 (2019-10)
EUROPEAN STANDARD
Technical characteristics and methods of measurement
for equipment for generation, transmission
and reception of Digital Selective Calling (DSC)
in the maritime MF, MF/HF and/or VHF mobile service;
Part 6: Class M DSC
---------------------- Page: 1 ----------------------
2 Draft ETSI EN 300 338-6 V1.2.0 (2019-10)
Reference
REN/ERM-TGMAR-601
Keywords
DSC, GMDSS, maritime, radio, SAR
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI
deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© ETSI 2019.
All rights reserved.
DECT™, PLUGTESTS™, UMTS™ and the ETSI logo are trademarks of ETSI registered for the benefit of its Members.
3GPP™ and LTE™ are trademarks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
oneM2M™ logo is a trademark of ETSI registered for the benefit of its Members and
of the oneM2M Partners.
®
GSM and the GSM logo are trademarks registered and owned by the GSM Association.
ETSI
---------------------- Page: 2 ----------------------
3 Draft ETSI EN 300 338-6 V1.2.0 (2019-10)
Contents
Intellectual Property Rights . 4
Foreword . 4
Modal verbs terminology . 4
1 Scope . 5
2 References . 5
2.1 Normative references . 5
2.2 Informative references . 6
3 Definition of terms, symbols and abbreviations . 6
3.1 Terms . 6
3.2 Symbols . 7
3.3 Abbreviations . 7
4 General requirements . 7
4.1 General . 7
4.2 Frequency of operation . 7
4.3 Class of emission . 8
4.4 Controls . 8
4.5 Indicators . 8
4.5.0 General . 8
4.5.1 Audible indicators . 8
4.5.2 Visual Indicators . 8
4.6 Labelling. 8
4.7 Instructions . 9
4.8 Self ID . 9
4.9 Own vessel MMSI . 9
4.10 Battery requirement . 9
5 DSC Operation . 10
5.1 Listen Before Talk (LBT) Protocol . 10
5.1.0 General . 10
5.1.1 Active Mode Wait Period Calculation . 10
5.1.2 Test Mode Wait Period Calculation . 10
5.2 DSC messages . 10
5.2.1 Active mode . 10
5.2.1.0 General . 10
5.2.1.1 Closed loop operation . 11
5.2.1.2 Open loop operation . 11
5.2.1.3 Distress self-cancel. 12
5.2.2 Test mode. 12
5.3 Action on receipt of acknowledgment messages to alerts . 12
6 Internal electronic position fixing device . 12
Annex A (informative): Change History . 13
History . 14
ETSI
---------------------- Page: 3 ----------------------
4 Draft ETSI EN 300 338-6 V1.2.0 (2019-10)
Intellectual Property Rights
Essential patents
IPRs essential or potentially essential to normative deliverables may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (https://ipr.etsi.org/).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Trademarks
The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners.
ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no
right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does
not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks.
Foreword
This draft European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic compatibility
and Radio spectrum Matters (ERM), and is now submitted for the combined Public Enquiry and Vote phase of the ETSI
standards EN Approval Procedure.
The present document is part 6 of a multi-part deliverable. Full details of the entire series can be found in part 1 [i.1].
Proposed national transposition dates
Date of latest announcement of this EN (doa): 3 months after ETSI publication
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 6 months after doa
Date of withdrawal of any conflicting National Standard (dow): 18 months after doa
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
ETSI
---------------------- Page: 4 ----------------------
5 Draft ETSI EN 300 338-6 V1.2.0 (2019-10)
1 Scope
The present document states the minimum requirements for devices using Digital Selective Calling (DSC) Class M, for
Man Overboard (MOB). The present document defines the requirements for equipment that uses DSC alerting and
signalling in the maritime mobile bands and particularly the GMDSS distress and safety channels. Such equipment is
not intended to provide any subsequent communications or telephony facilities.
The present document is part 6 of a multi-part deliverable that covers the channel access rules and technical
requirements applicable to these devices.
2 References
2.1 Normative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
https://docbox.etsi.org/Reference/.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are necessary for the application of the present document.
[1] Recommendation ITU-R M.493-15 (01/2019): "Digital selective-calling system for use in the
maritime mobile service".
[2] ETSI EN 303 098: "Maritime low power personal locating devices employing AIS; Harmonised
Standard for access to radio spectrum".
[3] Recommendation ITU-R M.585-7: "Assignment and use of identities in the maritime mobile
service".
[4] Recommendation ITU-R M.821-1: "Optional expansion of the digital selective-calling system for
use in the maritime mobile service".
[5] CENELEC EN 61108-1: "Maritime navigation and radiocommunication equipment and systems -
Global navigation satellite systems (GNSS) - Part 1: Global positioning system (GPS) - Receiver
equipment - Performance standards, methods of testing and required test results".
[6] CENELEC EN 61108-2: "Maritime navigation and radiocommunication equipment and systems -
Global navigation satellite systems (GNSS) - Part 2: Global navigation satellite system
(GLONASS) - Receiver equipment - Performance standards, methods of testing and required test
results".
[7] CENELEC EN 61108-3: "Maritime navigation and radiocommunication equipment and systems -
Global navigation satellite systems (GNSS) - Part 3: Galileo receiver equipment - Performance
requirements, methods of testing and required test results".
ETSI
---------------------- Page: 5 ----------------------
6 Draft ETSI EN 300 338-6 V1.2.0 (2019-10)
2.2 Informative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are not necessary for the application of the present document but they assist the
user with regard to a particular subject area.
[i.1] ETSI EN 300 338-1: "Technical characteristics and methods of measurement for equipment for
generation, transmission and reception of Digital Selective Calling (DSC) in the maritime MF,
MF/HF and/or VHF mobile service; Part 1: Common requirements".
3 Definition of terms, symbols and abbreviations
3.1 Terms
For the purposes of the present document, the terms given in ETSI EN 300 338-1 [i.1] and the following apply:
acknowledged: automated procedure which indicates that the objective of the initial DSC message has been achieved
activation: initial triggering of the MoB device i.e. both parts of the two step procedure are performed
active mode: activated mode, transmitting in an emergency situation
class M: specific class of DSC functionality for use by man overboard devices
closed loop: individual transmission to own vessel
default: value selected or an action taken by the equipment software in the absence of any operator input
distress alert: name given to the single distress DSC message with the format symbol 112
distress DSC message: DSC message or acknowledgement containing the distress information
distress information: symbols within a DSC message describing a distress situation consisting of the MMSI of the
vessel in distress, the nature of distress, the position of the vessel in distress, the UTC time of that position and the mode
of subsequent communication
factory default: default value that is set by the manufacturer such that the field or behaviour is defined prior to any
operator intervention
information characters: set of symbols in a DSC message that contains the items of interest for the recipient and is
used to compute the ECC symbol that terminates the message
non distress DSC message: DSC messages or acknowledgements that do not have the format specifier or category of
"distress"
open loop: transmitting to all ships (broadcast) 'using All ships call types'
symbol (as part of the DSC sentence): 7 binary bits of a 10 bit DSC word that have the information content
test mode: self-testing mode using an individual test call to own vessel
word (as part of the DSC sentence): 10 binary bits that make up the coded entities of a transmitted DSC message
NOTE: The 10 bits consist of a 7 bit "symbol" that gives the information content and 3 bit error check that gives
the number of 0 binary bits in the 7 bit symbol.
ETSI
---------------------- Page: 6 ----------------------
7 Draft ETSI EN 300 338-6 V1.2.0 (2019-10)
3.2 Symbols
Void.
3.3 Abbreviations
For the purposes of the present document, the following abbreviations apply:
AIS Automatic Identification System
CIRM Comite International Radio-Maritime
DSC Digital Selective Calling
ECC Error Check Character
GMDSS Global Maritime Distress and Safety System
GMSK Gaussian Minimum Shift Keying
GNSS Global Navigation Satellite System
GPS Global Positioning System
HF High Frequency
ID IDentity
ITU International Telecommunications Union
ITU-R ITU - Radiocommunications Sector
LBT Listen Before Talk
MF Medium Frequency
MMSI Maritime Mobile Service Identity
MOB Man Overboard
PM Phase Modulation
UTC
...
SLOVENSKI STANDARD
oSIST prEN 300 338-6 V1.2.0:2019
01-december-2019
Tehnične karakteristike in merilne metode za naprave, ki generirajo, oddajajo in
sprejemajo digitalni selektivni klic (DSC) v pomorski mobilni storitvi, ki deluje v
območju MF, MF/HF oziroma VHF - 6. del: Digitalni selektivni klic razreda M
Technical characteristics and methods of measurement for equipment for generation,
transmission and reception of Digital Selective Calling (DSC) in the maritime MF, MF/HF
and/or VHF mobile service - Part 6: Class M DSC
Ta slovenski standard je istoveten z: ETSI EN 300 338-6 V1.2.0 (2019-10)
ICS:
33.060.20 Sprejemna in oddajna Receiving and transmitting
oprema equipment
47.020.70 Navigacijska in krmilna Navigation and control
oprema equipment
oSIST prEN 300 338-6 V1.2.0:2019 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN 300 338-6 V1.2.0:2019
---------------------- Page: 2 ----------------------
oSIST prEN 300 338-6 V1.2.0:2019
Draft ETSI EN 300 338-6 V1.2.0 (2019-10)
EUROPEAN STANDARD
Technical characteristics and methods of measurement
for equipment for generation, transmission
and reception of Digital Selective Calling (DSC)
in the maritime MF, MF/HF and/or VHF mobile service;
Part 6: Class M DSC
---------------------- Page: 3 ----------------------
oSIST prEN 300 338-6 V1.2.0:2019
2 Draft ETSI EN 300 338-6 V1.2.0 (2019-10)
Reference
REN/ERM-TGMAR-601
Keywords
DSC, GMDSS, maritime, radio, SAR
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI
deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© ETSI 2019.
All rights reserved.
DECT™, PLUGTESTS™, UMTS™ and the ETSI logo are trademarks of ETSI registered for the benefit of its Members.
3GPP™ and LTE™ are trademarks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
oneM2M™ logo is a trademark of ETSI registered for the benefit of its Members and
of the oneM2M Partners.
®
GSM and the GSM logo are trademarks registered and owned by the GSM Association.
ETSI
---------------------- Page: 4 ----------------------
oSIST prEN 300 338-6 V1.2.0:2019
3 Draft ETSI EN 300 338-6 V1.2.0 (2019-10)
Contents
Intellectual Property Rights . 4
Foreword . 4
Modal verbs terminology . 4
1 Scope . 5
2 References . 5
2.1 Normative references . 5
2.2 Informative references . 6
3 Definition of terms, symbols and abbreviations . 6
3.1 Terms . 6
3.2 Symbols . 7
3.3 Abbreviations . 7
4 General requirements . 7
4.1 General . 7
4.2 Frequency of operation . 7
4.3 Class of emission . 8
4.4 Controls . 8
4.5 Indicators . 8
4.5.0 General . 8
4.5.1 Audible indicators . 8
4.5.2 Visual Indicators . 8
4.6 Labelling. 8
4.7 Instructions . 9
4.8 Self ID . 9
4.9 Own vessel MMSI . 9
4.10 Battery requirement . 9
5 DSC Operation . 10
5.1 Listen Before Talk (LBT) Protocol . 10
5.1.0 General . 10
5.1.1 Active Mode Wait Period Calculation . 10
5.1.2 Test Mode Wait Period Calculation . 10
5.2 DSC messages . 10
5.2.1 Active mode . 10
5.2.1.0 General . 10
5.2.1.1 Closed loop operation . 11
5.2.1.2 Open loop operation . 11
5.2.1.3 Distress self-cancel. 12
5.2.2 Test mode. 12
5.3 Action on receipt of acknowledgment messages to alerts . 12
6 Internal electronic position fixing device . 12
Annex A (informative): Change History . 13
History . 14
ETSI
---------------------- Page: 5 ----------------------
oSIST prEN 300 338-6 V1.2.0:2019
4 Draft ETSI EN 300 338-6 V1.2.0 (2019-10)
Intellectual Property Rights
Essential patents
IPRs essential or potentially essential to normative deliverables may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (https://ipr.etsi.org/).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Trademarks
The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners.
ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no
right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does
not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks.
Foreword
This draft European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic compatibility
and Radio spectrum Matters (ERM), and is now submitted for the combined Public Enquiry and Vote phase of the ETSI
standards EN Approval Procedure.
The present document is part 6 of a multi-part deliverable. Full details of the entire series can be found in part 1 [i.1].
Proposed national transposition dates
Date of latest announcement of this EN (doa): 3 months after ETSI publication
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 6 months after doa
Date of withdrawal of any conflicting National Standard (dow): 18 months after doa
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
ETSI
---------------------- Page: 6 ----------------------
oSIST prEN 300 338-6 V1.2.0:2019
5 Draft ETSI EN 300 338-6 V1.2.0 (2019-10)
1 Scope
The present document states the minimum requirements for devices using Digital Selective Calling (DSC) Class M, for
Man Overboard (MOB). The present document defines the requirements for equipment that uses DSC alerting and
signalling in the maritime mobile bands and particularly the GMDSS distress and safety channels. Such equipment is
not intended to provide any subsequent communications or telephony facilities.
The present document is part 6 of a multi-part deliverable that covers the channel access rules and technical
requirements applicable to these devices.
2 References
2.1 Normative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
https://docbox.etsi.org/Reference/.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are necessary for the application of the present document.
[1] Recommendation ITU-R M.493-15 (01/2019): "Digital selective-calling system for use in the
maritime mobile service".
[2] ETSI EN 303 098: "Maritime low power personal locating devices employing AIS; Harmonised
Standard for access to radio spectrum".
[3] Recommendation ITU-R M.585-7: "Assignment and use of identities in the maritime mobile
service".
[4] Recommendation ITU-R M.821-1: "Optional expansion of the digital selective-calling system for
use in the maritime mobile service".
[5] CENELEC EN 61108-1: "Maritime navigation and radiocommunication equipment and systems -
Global navigation satellite systems (GNSS) - Part 1: Global positioning system (GPS) - Receiver
equipment - Performance standards, methods of testing and required test results".
[6] CENELEC EN 61108-2: "Maritime navigation and radiocommunication equipment and systems -
Global navigation satellite systems (GNSS) - Part 2: Global navigation satellite system
(GLONASS) - Receiver equipment - Performance standards, methods of testing and required test
results".
[7] CENELEC EN 61108-3: "Maritime navigation and radiocommunication equipment and systems -
Global navigation satellite systems (GNSS) - Part 3: Galileo receiver equipment - Performance
requirements, methods of testing and required test results".
ETSI
---------------------- Page: 7 ----------------------
oSIST prEN 300 338-6 V1.2.0:2019
6 Draft ETSI EN 300 338-6 V1.2.0 (2019-10)
2.2 Informative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are not necessary for the application of the present document but they assist the
user with regard to a particular subject area.
[i.1] ETSI EN 300 338-1: "Technical characteristics and methods of measurement for equipment for
generation, transmission and reception of Digital Selective Calling (DSC) in the maritime MF,
MF/HF and/or VHF mobile service; Part 1: Common requirements".
3 Definition of terms, symbols and abbreviations
3.1 Terms
For the purposes of the present document, the terms given in ETSI EN 300 338-1 [i.1] and the following apply:
acknowledged: automated procedure which indicates that the objective of the initial DSC message has been achieved
activation: initial triggering of the MoB device i.e. both parts of the two step procedure are performed
active mode: activated mode, transmitting in an emergency situation
class M: specific class of DSC functionality for use by man overboard devices
closed loop: individual transmission to own vessel
default: value selected or an action taken by the equipment software in the absence of any operator input
distress alert: name given to the single distress DSC message with the format symbol 112
distress DSC message: DSC message or acknowledgement containing the distress information
distress information: symbols within a DSC message describing a distress situation consisting of the MMSI of the
vessel in distress, the nature of distress, the position of the vessel in distress, the UTC time of that position and the mode
of subsequent communication
factory default: default value that is set by the manufacturer such that the field or behaviour is defined prior to any
operator intervention
information characters: set of symbols in a DSC message that contains the items of interest for the recipient and is
used to compute the ECC symbol that terminates the message
non distress DSC message: DSC messages or acknowledgements that do not have the format specifier or category of
"distress"
open loop: transmitting to all ships (broadcast) 'using All ships call types'
symbol (as part of the DSC sentence): 7 binary bits of a 10 bit DSC word that have the information content
test mode: self-testing mode using an individual test call to own vessel
word (as part of the DSC sentence): 10 binary bits that make up the coded entities of a transmitted DSC message
NOTE: The 10 bits consist of a 7 bit "symbol" that gives the information content and 3 bit error check that gives
the number of 0 binary bits in the 7 bit symbol.
ETSI
---------------------- Page: 8 ----------------------
oSIST prEN 300 338-6 V1.2.0:2019
7 Draft ETSI EN 300 338-6 V1.2.0 (2019-10)
3.2 Symbols
Void.
3.3 Abbreviations
For the purposes of the present document, the following abbreviations apply:
AIS Automati
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.