ETSI EN 302 217-2-1 V2.1.1 (2014-12)
Fixed Radio Systems; Characteristics and requirements for point-to-point equipment and antennas; Part 2-1: System-dependent requirements for digital systems operating in frequency bands where frequency co-ordination is applied
Fixed Radio Systems; Characteristics and requirements for point-to-point equipment and antennas; Part 2-1: System-dependent requirements for digital systems operating in frequency bands where frequency co-ordination is applied
REN/ATTM-04017
Fiksni radijski sistemi - Karakteristike in zahteve za opremo in antene tipa točka-točka - 2-1. del: Sistemsko odvisne zahteve za digitalne sisteme, ki delujejo v frekvenčnih pasovih, kjer se uporablja frekvenčna koordinacija
General Information
Buy Standard
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Fixed Radio Systems - Characteristics and requirements for point-to-point equipment and antennas - Part 2-1: System-dependent requirements for digital systems operating in frequency bands where frequency co-ordination is applied33.120.40AnteneAerials33.060.30Radiorelejni in fiksni satelitski komunikacijski sistemiRadio relay and fixed satellite communications systemsICS:Ta slovenski standard je istoveten z:EN 302 217-2-1 V2.1.1SIST EN 302 217-2-1 V2.1.1:2015en01-junij-2015SIST EN 302 217-2-1 V2.1.1:2015SLOVENSKI
STANDARD
SIST EN 302 217-2-1 V2.1.1:2015
ETSI EN 302 217-2-1 V2.1.1 (2014-12) Fixed Radio Systems; Characteristics and requirements
for point-to-point equipment and antennas;
Part 2-1: System-dependent requirements
for digital systems operating in frequency bands where frequency co-ordination is applied
EUROPEAN STANDARD SIST EN 302 217-2-1 V2.1.1:2015
ETSI ETSI EN 302 217-2-1 V2.1.1 (2014-12)2
Reference REN/ATTM-04017 Keywords DFRS, digital, DRRS, FWA, point-to-point, radio, regulation, transmission ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00
Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C Association à but non lucratif enregistrée à la Sous-Préfecture de Grasse (06) N° 7803/88
Important notice The present document can be downloaded from: http://www.etsi.org The present document may be made available in electronic versions and/or in print. The content of any electronic and/or print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at http://portal.etsi.org/tb/status/status.asp If you find errors in the present document, please send your comment to one of the following services: http://portal.etsi.org/chaircor/ETSI_support.asp Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm except as authorized by written permission of ETSI. The content of the PDF version shall not be modified without the written authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2014. All rights reserved.
DECTTM, PLUGTESTSTM, UMTSTM and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members. 3GPPTM and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association. SIST EN 302 217-2-1 V2.1.1:2015
ETSI ETSI EN 302 217-2-1 V2.1.1 (2014-12)3 Contents Intellectual Property Rights . 5 Foreword . 5 Modal verbs terminology . 5 Introduction . 5 1 Scope . 6 2 References . 6 2.1 Normative references . 6 2.2 Informative references . 8 3 Definitions, symbols and abbreviations . 9 3.1 Definitions . 9 3.2 Symbols . 9 3.3 Abbreviations . 9 4 General characteristics . 9 4.1 Frequency bands and channel arrangements . 9 4.2 Special compatibility requirements between systems . 10 4.3 Transmission capacity and spectral efficiency . 10 5 Main requirements . 10 5.1 System nominal loading . 11 5.2 Environmental profile . 11 5.3 Transmitter characteristics. 11 5.3.1 Transmitter power and power tolerance . 11 5.3.1.1 Maximum power . 11 5.3.1.2 Transmitter output power tolerance . 11 5.3.2 Transmitter power and frequency control . 12 5.3.2.1 Transmitter power control (ATPC and RTPC) . 12 5.3.2.1.1 Automatic Transmitter Power Control (ATPC) . 12 5.3.2.1.2 Remote Transmitter Power Control (RTPC) . 13 5.3.2.2 Remote Frequency Control (RFC) . 13 5.3.3 Radio Frequency (RF) spectrum mask. 13 5.3.4 Discrete CW components exceeding the spectrum mask limit . 13 5.3.4.1 Discrete CW components at the symbol rate . 13 5.3.4.2 Other discrete CW components exceeding the spectrum mask limit . 13 5.3.5 Spurious emissions - external . 13 5.3.6 Radio frequency tolerance . 13 5.4 Receiver characteristics . 14 5.4.1 Spurious emissions-external . 14 5.5 System performance without diversity . 14 5.5.1 BER as a function of receiver signal level . 14 5.5.2 Interference sensitivity . 14 5.5.2.1 Co-channel "external" interference sensitivity . 14 5.5.2.2 Adjacent channel interference sensitivity . 14 5.5.2.3 CW spurious interference . 14 6 Complementary requirements . 15 6.1 Branching/feeder requirements . 15 6.1.1 Waveguide flanges (or other connectors) . 15 6.1.2 Return loss of feeder/antenna systems at equipment antenna port (C/C' reference point) . 16 6.2 Intermodulation products . 16 6.3 Transmitter characteristics. 17 6.3.1 Spurious emissions - internal . 17 6.3.2 Radio Frequency (RF) spectrum mask when mixed supplier compatibility is required . 17 6.4 Receiver characteristics . 18 6.4.1 Maximum input level and input level range . 18 6.4.2 Spurious emissions - internal . 19 SIST EN 302 217-2-1 V2.1.1:2015
ETSI ETSI EN 302 217-2-1 V2.1.1 (2014-12)4 6.4.3 Image rejection . 19 6.4.4 Innermost channel selectivity . 20 6.5 System performance without diversity . 20 6.5.1 Equipment Residual BER (RBER) . 20 6.5.2 Distortion sensitivity . 22 6.5.2.1 Introduction . 22 6.5.2.2 Requirement . 22 6.5.2.3 Assessment . 23 6.5.3 Interference sensitivity for CCDP with XPIC operation . 24 6.5.3.1 General . 24 6.5.3.2 Co-channel "internal" interference sensitivity in flat fading conditions . 24 6.6 System characteristics with diversity . 24 6.6.1 Differential delay compensation . 24 6.6.2 BER performance . 24 Annex A (normative): Spectrum masks and receiver selectivity when mixed supplier compatibility is required . 25 A.0 Introduction . 25 A.1 TX masks assessment . 26 A.2 Normal channels - Emission mask floor . 26 A.2.1 RBER impact . 26 A.2.2 Local TX to RX compatibility . 26 A.2.2.1 Spectrum mask . 26 A.2.2.2 Receiver selectivity . 27 A.3 Innermost channels for channel arrangements from about 4 GHz to about 8,5 GHz with channel separation of 28 MHz to 30 MHz . 27 A.3.1 Innermost channels spectrum masks . 27 A.3.2 Receiver innermost channel selectivity . 29 A.4 Innermost channels for channel arrangements from about 4 GHz to 11 GHz with channel separation of 40 MHz . 30 A.4.1 Innermost channels spectrum masks . 30 A.4.2 Receiver innermost channels selectivity . 31 A.5 Innermost channels for 18 GHz channel arrangements with channel separation of 55 MHz . 32 A.5.1 Innermost channels spectrum masks . 32 A.5.2 Receiver innermost channels selectivity . 33 Annexes B to E: Deleted and left void . 35 Annex F (normative): Definition of equivalent data rates for packet data, PDH/SDH and other signals on the traffic interface. 36 Annex G (informative): Additional information . 37 G.1 Residual Bit Error Ratio (RBER) and Residual Frame Error Ratio (RFER) . 37 G.2 Measurement test set for XPI characteristics . 38 G.3 Differential delay compensation range . 39 G.4 FER/BER equivalence and FER performance measurement equipment settings (example) . 40 G.4.1 FER/BER equivalence . 40 G.4.2 FER equipment settings and measurement techniques (example) . 41 G.5 Automatic Transmitter Power Control (ATPC) . 41 Annex H (informative): Mitigation techniques referred in ERC/DEC(00)07 (18 GHz band) . 43 Annex I (informative): Change History . 44 History . 45
SIST EN 302 217-2-1 V2.1.1:2015
ETSI ETSI EN 302 217-2-1 V2.1.1 (2014-12)5 Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (http://ipr.etsi.org). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This European Standard (EN) has been produced by ETSI Technical Committee Access, Terminals, Transmission and Multiplexing (ATTM). The present document is part 2-1 of a multi-part deliverable covering the Fixed Radio Systems; Characteristics and requirements for point-to-point equipment and antennas. Full details of the entire series can be found in part 1 [15].
National transposition dates Date of adoption of this EN: 5 December 2014 Date of latest announcement of this EN (doa): 31 March 2015 Date of latest publication of new National Standard or endorsement of this EN (dop/e):
30 September 2015 Date of withdrawal of any conflicting National Standard (dow): 30 September 2015
Modal verbs terminology In the present document "shall", "shall not", "should", "should not", "may", "may not", "need", "need not", "will", "will not", "can" and "cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of provisions). "must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation. Introduction The introduction of EN 302 217-1 [15] applies. SIST EN 302 217-2-1 V2.1.1:2015
ETSI ETSI EN 302 217-2-1 V2.1.1 (2014-12)6 1 Scope The present document summarizes all system-dependent requirements for Point-to-Point (P-P) equipment in applications deployed in bands where frequency co-ordination is generally applied. These requirements are introduced in two different clauses sub-sets: • Main requirements are requirements that are also related to the "essential requirements" under article 3.2 of the R&TTE Directive [1] and further detailed in the Harmonized Standard EN 302 217-2-2 [16]. • Complementary requirements are requirements that are not related to essential requirements under article 3.2 of the R&TTE Directive [1]. Nevertheless they have been commonly agreed for proper system operation and deployment when specific deployment conditions or compatibility requirements are present. Compliance to all or some of these requirements is left to supplier decision. Description and limits for parameters relevant to essential requirements under article 3.2 of R&TTE Directive [1] are given in the Harmonized Standard EN 302 217-2-2 [16]. For other system-dependent parameters where standardization is required but that do not affect the R&TTE Directive "essential requirements" mentioned above, description and limits are detailed in the present document in clause 6 and in the annex A, annex F and annex G. The present document deals with Radio Frequency (RF) and base-band equipment characteristics; antenna system requirements are covered in EN 302 217-4-1 [i.9] and EN 302 217-4-2 [i.10]. The present document does not cover test procedures and test conditions which are set out in EN 301 126-1 [14]. As the maximum transmission rate in a given bandwidth depends on system spectral efficiency, equipment are subdivided in different spectral efficiency classes as defined in EN 302 217-2-2 [16]. The spectral efficiency classes are indicative only and do not imply any constraint to the actual modulation format, provided that all the requirements in the relevant parts of this Multi-part deliverable for the declared class are met. Guidance on the definition of radio parameters relevant to the essential requirements under article 3.2 of R&TTE Directive [1] for DFRS may be found in TR 101 506 [i.6].
Technical background for most of the parameters and requirements referred to in this Multi-part deliverable may be found in TR 101 036-1 [i.5]. 2 References References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the reference document (including any amendments) applies. Referenced documents which are not found to be publicly available in the expected location might be found at http://docbox.etsi.org/Reference. NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee their long term validity. 2.1 Normative references The following referenced documents are necessary for the application of the present document. [1] Directive 1999/5/EC of the European Parliament and of the Council of 9 March 1999 on radio equipment and telecommunications terminal equipment and the mutual recognition of their conformity (R&TTE Directive). [2] CENELEC EN 122150: "Sectional Specification: Radio frequency coaxial connectors - Series EIA flange". SIST EN 302 217-2-1 V2.1.1:2015
ETSI ETSI EN 302 217-2-1 V2.1.1 (2014-12)7 [3] CEPT/ERC/DEC(00)07: "ERC Decision of 19 October 2000 on the shared use of the band 17.7 - 19.7 GHz by the fixed service and Earth stations of the fixed-satellite service (space-to-Earth)". [4] ETSI EN 300 019-1-0: "Environmental Engineering (EE); Environmental conditions and environmental tests for telecommunications equipment; Part 1-0: Classification of environmental conditions; Introduction". [5] ETSI EN 300 019-1-1: "Environmental Engineering (EE); Environmental conditions and environmental tests for telecommunications equipment; Part 1-1: Classification of environmental conditions; Storage". [6] ETSI EN 300 019-1-2: "Environmental Engineering (EE); Environmental conditions and environmental tests for telecommunications equipment; Part 1-2: Classification of environmental conditions; Transportation". [7] ETSI EN 300 019-1-3: "Environmental Engineering (EE); Environmental conditions and environmental tests for telecommunications equipment; Part 1-3: Classification of environmental conditions; Stationary use at weatherprotected locations". [8] ETSI EN 300 019-1-4: "Environmental Engineering (EE); Environmental conditions and environmental tests for telecommunications equipment; Part 1-4: Classification of environmental conditions; Stationary use at non-weatherprotected locations". [9] ETSI EN 300 019-2-0: "Environmental Engineering (EE); Environmental conditions and environmental tests for telecommunications equipment; Part 2-0: Specification of environmental tests; Introduction". [10] ETSI EN 300 019-2-1: "Environmental Engineering (EE); Environmental conditions and environmental tests for telecommunications equipment; Part 2-1: Specification of environmental tests; Storage". [11] ETSI EN 300 019-2-2: "Environmental Engineering (EE); Environmental conditions and environmental tests for telecommunications equipment; Part 2-2: Specification of environmental tests; Transportation". [12] ETSI EN 300 019-2-3: "Environmental Engineering (EE); Environmental conditions and environmental tests for telecommunications equipment; Part 2-3: Specification of environmental tests; Stationary use at weatherprotected locations". [13] ETSI EN 300 019-2-4: "Environmental Engineering (EE); Environmental conditions and environmental tests for telecommunications equipment; Part 2-4: Specification of environmental tests; Stationary use at non-weatherprotected locations". [14] ETSI EN 301 126-1: "Fixed Radio Systems; Conformance testing; Part 1: Point-to-Point equipment - Definitions, general requirements and test procedures". [15] ETSI EN 302 217-1: "Fixed Radio Systems; Characteristics and requirements for point-to-point equipment and antennas; Part 1: Overview and system-independent common characteristics". [16] ETSI EN 302 217-2-2: "Fixed Radio Systems; Characteristics and requirements for point-to-point equipment and antennas; Part 2-2: Digital systems operating in frequency bands where frequency co-ordination is applied; Harmonized EN covering the essential requirements of Article 3.2 of the R&TTE Directive". [17] IEC 60153-2: "Hollow metallic waveguides. Part 2: Relevant specifications for ordinary rectangular waveguides". [18] IEC 60154-2: "Flanges for waveguides. Part 2: Relevant specifications for flanges for ordinary rectangular waveguides". [19] IEC 60169-1: "Radio-frequency connectors. Part 1: General requirements and measuring methods". [20] IEC 60339 (all parts): "General purpose rigid coaxial transmission lines and their associated flange connectors". SIST EN 302 217-2-1 V2.1.1:2015
ETSI ETSI EN 302 217-2-1 V2.1.1 (2014-12)8 [21] IEC 60835-2-4: "Methods of measurement for equipment used in digital microwave radio transmission systems - Part 2: Measurements on terrestrial radio-relay systems -
Section 4: Transmitter/receiver including modulator/demodulator". [22] IEC 60835-2-8: "Methods of measurement for equipment used in digital microwave radio transmission systems - Part 2: Measurements on terrestrial radio-relay systems -
Section 8: Adaptive equalizer". [23] IEEE 802.3-2005: "IEEE Standard for Information technology - Telecommunications and information exchange between systems - Local and metropolitan area networks - Specific requirements - Part 3: Carrier Sense Multiple Access with Collision Detection (CSMA/CD) Access Method and Physical Layer Specifications". [24] IEEE 1802.3-2001: "IEEE Conformance Test Methodology for IEEE Standards for Local and Metropolitan Area Networks - Specific Requirements - Part 3: Carrier Sense Multiple Access with Collision Detection (CSMA/CD) Access Method and Physical Layer Specifications". [25] Void. [26] Recommendation ITU-R F.1093-2: "Effects of multipath propagation on the design and operation of line-of-sight digital fixed wireless systems". [27] Void. [28] Recommendation ITU-T O.151: "Error performance measuring equipment operating at the primary rate and above". [29] Recommendation ITU-T O.181: "Equipment to assess error performance on STM-N interfaces". [30] Recommendation ITU-T O.191: "Equipment to measure the cell transfer performance of ATM connections". 2.2 Informative references The following referenced documents are not necessary for the application of the present document but they assist the user with regard to a particular subject area. [i.1] ECC/REC(02)06: "Channel arrangements for digital Fixed Service Systems operating in the frequency range 7125-8500 MHz". [i.2] ERC/REC 12-03: "Harmonised radio frequency channel arrangements for digital terrestrial fixed systems operating in the band 17.7 GHz TO 19.7 GHz". [i.3] ERC/REC 14-01: "Radio-frequency channel arrangements for high capacity analogue and digital radio-relay systems operating in the band 5925 MHz - 6425 MHz". [i.4] ERC/REC 14-02: "Radio-frequency channel arrangements for high, medium and low capacity digital fixed service systems operating in the band 6425-7125 MHz". [i.5] ETSI TR 101 036-1: "Fixed Radio Systems; Generic wordings for standards on DFRS (Digital Fixed Radio Systems) characteristics; Part 1: General aspects and point-to-point equipment parameters". [i.6] ETSI TR 101 506: "Fixed Radio Systems; Generic definitions, terminology and applicability of essen
...
ETSI EN 302 217-2-1 V2.1.1 (2014-12)
EUROPEAN STANDARD
Fixed Radio Systems;
Characteristics and requirements
for point-to-point equipment and antennas;
Part 2-1: System-dependent requirements
for digital systems operating in frequency bands
where frequency co-ordination is applied
---------------------- Page: 1 ----------------------
2 ETSI EN 302 217-2-1 V2.1.1 (2014-12)
Reference
REN/ATTM-04017
Keywords
DFRS, digital, DRRS, FWA, point-to-point, radio,
regulation, transmission
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
http://portal.etsi.org/chaircor/ETSI_support.asp
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2014.
All rights reserved.
TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.
TM
3GPP and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI
---------------------- Page: 2 ----------------------
3 ETSI EN 302 217-2-1 V2.1.1 (2014-12)
Contents
Intellectual Property Rights . 5
Foreword . 5
Modal verbs terminology . 5
Introduction . 5
1 Scope . 6
2 References . 6
2.1 Normative references . 6
2.2 Informative references . 8
3 Definitions, symbols and abbreviations . 9
3.1 Definitions . 9
3.2 Symbols . 9
3.3 Abbreviations . 9
4 General characteristics . 9
4.1 Frequency bands and channel arrangements . 9
4.2 Special compatibility requirements between systems . 10
4.3 Transmission capacity and spectral efficiency . 10
5 Main requirements . 10
5.1 System nominal loading . 11
5.2 Environmental profile . 11
5.3 Transmitter characteristics. 11
5.3.1 Transmitter power and power tolerance . 11
5.3.1.1 Maximum power . 11
5.3.1.2 Transmitter output power tolerance . 11
5.3.2 Transmitter power and frequency control . 12
5.3.2.1 Transmitter power control (ATPC and RTPC) . 12
5.3.2.1.1 Automatic Transmitter Power Control (ATPC) . 12
5.3.2.1.2 Remote Transmitter Power Control (RTPC) . 13
5.3.2.2 Remote Frequency Control (RFC) . 13
5.3.3 Radio Frequency (RF) spectrum mask. 13
5.3.4 Discrete CW components exceeding the spectrum mask limit . 13
5.3.4.1 Discrete CW components at the symbol rate . 13
5.3.4.2 Other discrete CW components exceeding the spectrum mask limit . 13
5.3.5 Spurious emissions - external . 13
5.3.6 Radio frequency tolerance . 13
5.4 Receiver characteristics . 14
5.4.1 Spurious emissions-external . 14
5.5 System performance without diversity . 14
5.5.1 BER as a function of receiver signal level . 14
5.5.2 Interference sensitivity . 14
5.5.2.1 Co-channel "external" interference sensitivity . 14
5.5.2.2 Adjacent channel interference sensitivity . 14
5.5.2.3 CW spurious interference . 14
6 Complementary requirements . 15
6.1 Branching/feeder requirements . 15
6.1.1 Waveguide flanges (or other connectors) . 15
6.1.2 Return loss of feeder/antenna systems at equipment antenna port (C/C' reference point) . 16
6.2 Intermodulation products . 16
6.3 Transmitter characteristics. 17
6.3.1 Spurious emissions - internal . 17
6.3.2 Radio Frequency (RF) spectrum mask when mixed supplier compatibility is required . 17
6.4 Receiver characteristics . 18
6.4.1 Maximum input level and input level range . 18
6.4.2 Spurious emissions - internal . 19
ETSI
---------------------- Page: 3 ----------------------
4 ETSI EN 302 217-2-1 V2.1.1 (2014-12)
6.4.3 Image rejection . 19
6.4.4 Innermost channel selectivity . 20
6.5 System performance without diversity . 20
6.5.1 Equipment Residual BER (RBER) . 20
6.5.2 Distortion sensitivity . 22
6.5.2.1 Introduction . 22
6.5.2.2 Requirement . 22
6.5.2.3 Assessment . 23
6.5.3 Interference sensitivity for CCDP with XPIC operation . 24
6.5.3.1 General . 24
6.5.3.2 Co-channel "internal" interference sensitivity in flat fading conditions . 24
6.6 System characteristics with diversity . 24
6.6.1 Differential delay compensation . 24
6.6.2 BER performance . 24
Annex A (normative): Spectrum masks and receiver selectivity when mixed supplier
compatibility is required . 25
A.0 Introduction . 25
A.1 TX masks assessment . 26
A.2 Normal channels - Emission mask floor . 26
A.2.1 RBER impact . 26
A.2.2 Local TX to RX compatibility . 26
A.2.2.1 Spectrum mask . 26
A.2.2.2 Receiver selectivity . 27
A.3 Innermost channels for channel arrangements from about 4 GHz to about 8,5 GHz with channel
separation of 28 MHz to 30 MHz . 27
A.3.1 Innermost channels spectrum masks . 27
A.3.2 Receiver innermost channel selectivity . 29
A.4 Innermost channels for channel arrangements from about 4 GHz to 11 GHz with channel
separation of 40 MHz . 30
A.4.1 Innermost channels spectrum masks . 30
A.4.2 Receiver innermost channels selectivity . 31
A.5 Innermost channels for 18 GHz channel arrangements with channel separation of 55 MHz . 32
A.5.1 Innermost channels spectrum masks . 32
A.5.2 Receiver innermost channels selectivity . 33
Annexes B to E: Deleted and left void . 35
Annex F (normative): Definition of equivalent data rates for packet data, PDH/SDH and
other signals on the traffic interface. 36
Annex G (informative): Additional information . 37
G.1 Residual Bit Error Ratio (RBER) and Residual Frame Error Ratio (RFER) . 37
G.2 Measurement test set for XPI characteristics . 38
G.3 Differential delay compensation range . 39
G.4 FER/BER equivalence and FER performance measurement equipment settings (example) . 40
G.4.1 FER/BER equivalence . 40
G.4.2 FER equipment settings and measurement techniques (example) . 41
G.5 Automatic Transmitter Power Control (ATPC) . 41
Annex H (informative): Mitigation techniques referred in ERC/DEC(00)07 (18 GHz band) . 43
Annex I (informative): Change History . 44
History . 45
ETSI
---------------------- Page: 4 ----------------------
5 ETSI EN 302 217-2-1 V2.1.1 (2014-12)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (http://ipr.etsi.org).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This European Standard (EN) has been produced by ETSI Technical Committee Access, Terminals, Transmission and
Multiplexing (ATTM).
The present document is part 2-1 of a multi-part deliverable covering the Fixed Radio Systems; Characteristics and
requirements for point-to-point equipment and antennas. Full details of the entire series can be found in part 1 [15].
National transposition dates
Date of adoption of this EN: 5 December 2014
Date of latest announcement of this EN (doa): 31 March 2015
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 30 September 2015
Date of withdrawal of any conflicting National Standard (dow): 30 September 2015
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "may not", "need", "need not", "will",
"will not", "can" and "cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms
for the expression of provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
Introduction
The introduction of EN 302 217-1 [15] applies.
ETSI
---------------------- Page: 5 ----------------------
6 ETSI EN 302 217-2-1 V2.1.1 (2014-12)
1 Scope
The present document summarizes all system-dependent requirements for Point-to-Point (P-P) equipment in
applications deployed in bands where frequency co-ordination is generally applied. These requirements are introduced
in two different clauses sub-sets:
• Main requirements are requirements that are also related to the "essential requirements" under article 3.2 of
the R&TTE Directive [1] and further detailed in the Harmonized Standard EN 302 217-2-2 [16].
• Complementary requirements are requirements that are not related to essential requirements under
article 3.2 of the R&TTE Directive [1]. Nevertheless they have been commonly agreed for proper system
operation and deployment when specific deployment conditions or compatibility requirements are present.
Compliance to all or some of these requirements is left to supplier decision.
Description and limits for parameters relevant to essential requirements under article 3.2 of R&TTE Directive [1] are
given in the Harmonized Standard EN 302 217-2-2 [16].
For other system-dependent parameters where standardization is required but that do not affect the R&TTE Directive
"essential requirements" mentioned above, description and limits are detailed in the present document in clause 6 and in
the annex A, annex F and annex G.
The present document deals with Radio Frequency (RF) and base-band equipment characteristics; antenna system
requirements are covered in EN 302 217-4-1 [i.9] and EN 302 217-4-2 [i.10].
The present document does not cover test procedures and test conditions which are set out in EN 301 126-1 [14].
As the maximum transmission rate in a given bandwidth depends on system spectral efficiency, equipment are
subdivided in different spectral efficiency classes as defined in EN 302 217-2-2 [16].
The spectral efficiency classes are indicative only and do not imply any constraint to the actual modulation format,
provided that all the requirements in the relevant parts of this Multi-part deliverable for the declared class are met.
Guidance on the definition of radio parameters relevant to the essential requirements under article 3.2 of R&TTE
Directive [1] for DFRS may be found in TR 101 506 [i.6].
Technical background for most of the parameters and requirements referred to in this Multi-part deliverable may be
found in TR 101 036-1 [i.5].
2 References
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
reference document (including any amendments) applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
http://docbox.etsi.org/Reference.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
2.1 Normative references
The following referenced documents are necessary for the application of the present document.
[1] Directive 1999/5/EC of the European Parliament and of the Council of 9 March 1999 on radio
equipment and telecommunications terminal equipment and the mutual recognition of their
conformity (R&TTE Directive).
[2] CENELEC EN 122150: "Sectional Specification: Radio frequency coaxial connectors - Series EIA
flange".
ETSI
---------------------- Page: 6 ----------------------
7 ETSI EN 302 217-2-1 V2.1.1 (2014-12)
[3] CEPT/ERC/DEC(00)07: "ERC Decision of 19 October 2000 on the shared use of the band 17.7 -
19.7 GHz by the fixed service and Earth stations of the fixed-satellite service (space-to-Earth)".
[4] ETSI EN 300 019-1-0: "Environmental Engineering (EE); Environmental conditions and
environmental tests for telecommunications equipment; Part 1-0: Classification of environmental
conditions; Introduction".
[5] ETSI EN 300 019-1-1: "Environmental Engineering (EE); Environmental conditions and
environmental tests for telecommunications equipment; Part 1-1: Classification of environmental
conditions; Storage".
[6] ETSI EN 300 019-1-2: "Environmental Engineering (EE); Environmental conditions and
environmental tests for telecommunications equipment; Part 1-2: Classification of environmental
conditions; Transportation".
[7] ETSI EN 300 019-1-3: "Environmental Engineering (EE); Environmental conditions and
environmental tests for telecommunications equipment; Part 1-3: Classification of environmental
conditions; Stationary use at weatherprotected locations".
[8] ETSI EN 300 019-1-4: "Environmental Engineering (EE); Environmental conditions and
environmental tests for telecommunications equipment; Part 1-4: Classification of environmental
conditions; Stationary use at non-weatherprotected locations".
[9] ETSI EN 300 019-2-0: "Environmental Engineering (EE); Environmental conditions and
environmental tests for telecommunications equipment; Part 2-0: Specification of environmental
tests; Introduction".
[10] ETSI EN 300 019-2-1: "Environmental Engineering (EE); Environmental conditions and
environmental tests for telecommunications equipment; Part 2-1: Specification of environmental
tests; Storage".
[11] ETSI EN 300 019-2-2: "Environmental Engineering (EE); Environmental conditions and
environmental tests for telecommunications equipment; Part 2-2: Specification of environmental
tests; Transportation".
[12] ETSI EN 300 019-2-3: "Environmental Engineering (EE); Environmental conditions and
environmental tests for telecommunications equipment; Part 2-3: Specification of environmental
tests; Stationary use at weatherprotected locations".
[13] ETSI EN 300 019-2-4: "Environmental Engineering (EE); Environmental conditions and
environmental tests for telecommunications equipment; Part 2-4: Specification of environmental
tests; Stationary use at non-weatherprotected locations".
[14] ETSI EN 301 126-1: "Fixed Radio Systems; Conformance testing; Part 1: Point-to-Point
equipment - Definitions, general requirements and test procedures".
[15] ETSI EN 302 217-1: "Fixed Radio Systems; Characteristics and requirements for point-to-point
equipment and antennas; Part 1: Overview and system-independent common characteristics".
[16] ETSI EN 302 217-2-2: "Fixed Radio Systems; Characteristics and requirements for point-to-point
equipment and antennas; Part 2-2: Digital systems operating in frequency bands where frequency
co-ordination is applied; Harmonized EN covering the essential requirements of Article 3.2 of the
R&TTE Directive".
[17] IEC 60153-2: "Hollow metallic waveguides. Part 2: Relevant specifications for ordinary
rectangular waveguides".
[18] IEC 60154-2: "Flanges for waveguides. Part 2: Relevant specifications for flanges for ordinary
rectangular waveguides".
[19] IEC 60169-1: "Radio-frequency connectors. Part 1: General requirements and measuring
methods".
[20] IEC 60339 (all parts): "General purpose rigid coaxial transmission lines and their associated flange
connectors".
ETSI
---------------------- Page: 7 ----------------------
8 ETSI EN 302 217-2-1 V2.1.1 (2014-12)
[21] IEC 60835-2-4: "Methods of measurement for equipment used in digital microwave radio
transmission systems - Part 2: Measurements on terrestrial radio-relay systems -
Section 4: Transmitter/receiver including modulator/demodulator".
[22] IEC 60835-2-8: "Methods of measurement for equipment used in digital microwave radio
transmission systems - Part 2: Measurements on terrestrial radio-relay systems -
Section 8: Adaptive equalizer".
[23] IEEE 802.3-2005: "IEEE Standard for Information technology - Telecommunications and
information exchange between systems - Local and metropolitan area networks - Specific
requirements - Part 3: Carrier Sense Multiple Access with Collision Detection (CSMA/CD)
Access Method and Physical Layer Specifications".
[24] IEEE 1802.3-2001: "IEEE Conformance Test Methodology for IEEE Standards for Local and
Metropolitan Area Networks - Specific Requirements - Part 3: Carrier Sense Multiple Access with
Collision Detection (CSMA/CD) Access Method and Physical Layer Specifications".
[25] Void.
[26] Recommendation ITU-R F.1093-2: "Effects of multipath propagation on the design and operation
of line-of-sight digital fixed wireless systems".
[27] Void.
[28] Recommendation ITU-T O.151: "Error performance measuring equipment operating at the
primary rate and above".
[29] Recommendation ITU-T O.181: "Equipment to assess error performance on STM-N interfaces".
[30] Recommendation ITU-T O.191: "Equipment to measure the cell transfer performance of ATM
connections".
2.2 Informative references
The following referenced documents are not necessary for the application of the present document but they assist the
user with regard to a particular subject area.
[i.1] ECC/REC(02)06: "Channel arrangements for digital Fixed Service Systems operating in the
frequency range 7125-8500 MHz".
[i.2] ERC/REC 12-03: "Harmonised radio frequency channel arrangements for digital terrestrial fixed
systems operating in the band 17.7 GHz TO 19.7 GHz".
[i.3] ERC/REC 14-01: "Radio-frequency channel arrangements for high capacity analogue and digital
radio-relay systems operating in the band 5925 MHz - 6425 MHz".
[i.4] ERC/REC 14-02: "Radio-frequency channel arrangements for high, medium and low capacity
digital fixed service systems operating in the band 6425-7125 MHz".
[i.5] ETSI TR 101 036-1: "Fixed Radio Systems; Generic wordings for standards on DFRS (Digital
Fixed Radio Systems) characteristics; Part 1: General aspects and point-to-point equipment
parameters".
[i.6] ETSI TR 101 506: "Fixed Radio Systems; Generic definitions, terminology and applicability of
essential requirements under the article 3.2 of 1999/05/EC Directive to Fixed Radio Systems".
[i.7] ETSI TR 102 243-1: "Fixed Radio Systems; Representative values f
...
Draft ETSI EN 302 217-2-1 V2.0.1 (2014-08)
EUROPEAN STANDARD
Fixed Radio Systems;
Characteristics and requirements
for point-to-point equipment and antennas;
Part 2-1: System-dependent requirements
for digital systems operating in frequency bands
where frequency co-ordination is applied
---------------------- Page: 1 ----------------------
2 Draft ETSI EN 302 217-2-1 V2.0.1 (2014-08)
Reference
REN/ATTM-04017
Keywords
DFRS, digital, DRRS, FWA, point-to-point, radio,
regulation, transmission
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
http://portal.etsi.org/chaircor/ETSI_support.asp
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2014.
All rights reserved.
TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.
TM
3GPP and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI
---------------------- Page: 2 ----------------------
3 Draft ETSI EN 302 217-2-1 V2.0.1 (2014-08)
Contents
Intellectual Property Rights . 5
Foreword . 5
Modal verbs terminology . 5
Introduction . 5
1 Scope . 6
2 References . 6
2.1 Normative references . 6
2.2 Informative references . 8
3 Definitions, symbols and abbreviations . 9
3.1 Definitions . 9
3.2 Symbols . 9
3.3 Abbreviations . 9
4 General characteristics . 9
4.1 Frequency bands and channel arrangements . 9
4.2 Special compatibility requirements between systems . 10
4.3 Transmission capacity and spectral efficiency . 10
5 Main requirements . 10
5.1 System nominal loading . 10
5.2 Environmental profile . 11
5.3 Transmitter characteristics. 11
5.3.1 Transmitter power and power tolerance . 11
5.3.1.1 Maximum power . 11
5.3.1.2 Transmitter output power tolerance . 11
5.3.2 Transmitter power and frequency control . 12
5.3.2.1 Transmitter power control (ATPC and RTPC) . 12
5.3.2.1.1 Automatic Transmitter Power Control (ATPC) . 12
5.3.2.1.2 Remote Transmitter Power Control (RTPC) . 13
5.3.2.2 Remote Frequency Control (RFC) . 13
5.3.3 Radio Frequency (RF) spectrum mask. 13
5.3.4 Discrete CW components exceeding the spectrum mask limit . 13
5.3.4.1 Discrete CW components at the symbol rate . 13
5.3.4.2 Other discrete CW components exceeding the spectrum mask limit . 13
5.3.5 Spurious emissions - external . 13
5.3.6 Radio frequency tolerance . 13
5.4 Receiver characteristics . 14
5.4.1 Spurious emissions-external . 14
5.5 System performance without diversity . 14
5.5.1 BER as a function of receiver signal level . 14
5.5.2 Interference sensitivity . 14
5.5.2.1 Co-channel "external" interference sensitivity . 14
5.5.2.2 Adjacent channel interference sensitivity . 14
5.5.2.3 CW spurious interference . 14
6 Complementary requirements . 15
6.1 Branching/feeder requirements . 15
6.1.1 Waveguide flanges (or other connectors) . 15
6.1.2 Return loss of feeder/antenna systems at equipment antenna port (C/C' reference point) . 16
6.2 Intermodulation products . 16
6.3 Transmitter characteristics. 17
6.3.1 Spurious emissions - internal . 17
6.3.2 Radio Frequency (RF) spectrum mask when mixed supplier compatibility is required . 17
6.4 Receiver characteristics . 18
ETSI
---------------------- Page: 3 ----------------------
4 Draft ETSI EN 302 217-2-1 V2.0.1 (2014-08)
6.4.1 Maximum input level and input level range . 18
6.4.2 Spurious emissions - internal . 19
6.4.3 Image rejection . 19
6.4.4 Innermost channel selectivity . 20
6.5 System performance without diversity . 20
6.5.1 Equipment Residual BER (RBER) . 20
6.5.2 Distortion sensitivity . 22
6.5.2.1 Introduction . 22
6.5.2.2 Requirement . 22
6.5.2.3 Assessment . 23
6.5.3 Interference sensitivity for CCDP with XPIC operation . 24
6.5.3.1 General . 24
6.5.3.2 Co-channel "internal" interference sensitivity in flat fading conditions . 24
6.6 System characteristics with diversity . 24
6.6.1 Differential delay compensation . 24
6.6.2 BER performance . 24
Annex A (normative): Spectrum masks and receiver selectivity when mixed supplier
compatibility is required . 25
A.0 Introduction . 25
A.1 TX masks assessment . 26
A.2 Normal channels - Emission mask floor . 26
A.2.1 RBER impact . 26
A.2.2 Local TX to RX compatibility . 26
A.2.2.1 Spectrum mask . 26
A.2.2.2 Receiver selectivity . 27
A.3 Innermost channels for channel arrangements from about 4 GHz to about 8,5 GHz with channel
separation of 28 MHz to 30 MHz . 27
A.3.1 Innermost channels spectrum masks . 27
A.3.2 Receiver innermost channel selectivity . 29
A.4 Innermost channels for channel arrangements from about 4 GHz to 11 GHz with channel
separation of 40 MHz . 30
A.4.1 Innermost channels spectrum masks . 30
A.4.2 Receiver innermost channels selectivity . 31
A.5 Innermost channels for 18 GHz channel arrangements with channel separation of 55 MHz . 32
A.5.1 Innermost channels spectrum masks . 32
A.5.2 Receiver innermost channels selectivity . 33
Annexes B to E: Deleted and left void . 35
Annex F (normative): Definition of equivalent data rates for packet data, PDH/SDH and
other signals on the traffic interface. 36
Annex G (informative): Additional information . 37
G.1 Residual Bit Error Ratio (RBER) and Residual Frame Error Ratio (RFER) . 37
G.2 Measurement test set for XPI characteristics . 38
G.3 Differential delay compensation range . 39
G.4 FER/BER equivalence and FER performance measurement equipment settings (example) . 40
G.4.1 FER/BER equivalence . 40
G.4.2 FER equipment settings and measurement techniques (example) . 41
G.5 Automatic Transmitter Power Control (ATPC) . 41
Annex H (informative): Mitigation techniques referred in ERC/DEC(00)07 (18 GHz band) . 43
Annex I (informative): Change History . 44
History . 45
ETSI
---------------------- Page: 4 ----------------------
5 Draft ETSI EN 302 217-2-1 V2.0.1 (2014-08)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (http://ipr.etsi.org).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This draft European Standard (EN) has been produced by ETSI Technical Committee Access, Terminals, Transmission
and Multiplexing (ATTM), and is now submitted for the combined Public Enquiry and Vote phase of the ETSI
standards EN Approval Procedure.
The present document is part 2-1 of a multi-part deliverable covering the Fixed Radio Systems; Characteristics and
requirements for point-to-point equipment and antennas. Full details of the entire series can be found in part 1 [15].
Proposed national transposition dates
Date of latest announcement of this EN (doa): 3 months after ETSI publication
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 6 months after doa
Date of withdrawal of any conflicting National Standard (dow): 6 months after doa
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "may not", "need", "need not", "will",
"will not", "can" and "cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms
for the expression of provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
Introduction
The introduction of EN 302 217-1 [15] applies.
ETSI
---------------------- Page: 5 ----------------------
6 Draft ETSI EN 302 217-2-1 V2.0.1 (2014-08)
1 Scope
The present document summarizes all system-dependent requirements for Point-to-Point (P-P) equipment in
applications deployed in bands where frequency co-ordination is generally applied. These requirements are introduced
in two different clauses sub-sets:
• Main requirements are requirements that are also related to the "essential requirements" under article 3.2 of
the R&TTE Directive [1] and further detailed in the Harmonized Standard EN 302 217-2-2 [16].
• Complementary requirements are requirements that are not related to essential requirements under
article 3.2 of the R&TTE Directive [1]. Nevertheless they have been commonly agreed for proper system
operation and deployment when specific deployment conditions or compatibility requirements are present.
Compliance to all or some of these requirements is left to supplier decision.
Description and limits for parameters relevant to essential requirements under article 3.2 of R&TTE Directive [1] are
given in the Harmonized Standard EN 302 217-2-2 [16].
For other system-dependent parameters where standardization is required but that do not affect the R&TTE Directive
"essential requirements" mentioned above, description and limits are detailed in the present document in clause 6 and in
the annex A, annex F and annex G.
The present document deals with Radio Frequency (RF) and base-band equipment characteristics; antenna system
requirements are covered in EN 302 217-4-1 [i.9] and EN 302 217-4-2 [i.10].
The present document does not cover test procedures and test conditions which are set out in EN 301 126-1 [14].
As the maximum transmission rate in a given bandwidth depends on system spectral efficiency, equipment are
subdivided in different spectral efficiency classes as defined in EN 302 217-2-2 [16].
The spectral efficiency classes are indicative only and do not imply any constraint to the actual modulation format,
provided that all the requirements in the relevant parts of this Multi-part deliverable for the declared class are met.
Guidance on the definition of radio parameters relevant to the essential requirements under article 3.2 of R&TTE
Directive [1] for DFRS may be found in TR 101 506 [i.6].
Technical background for most of the parameters and requirements referred to in this Multi-part deliverable may be
found in TR 101 036-1 [i.5].
2 References
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
reference document (including any amendments) applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
http://docbox.etsi.org/Reference.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
2.1 Normative references
The following referenced documents are necessary for the application of the present document.
[1] Directive 1999/5/EC of the European Parliament and of the Council of 9 March 1999 on radio
equipment and telecommunications terminal equipment and the mutual recognition of their
conformity (R&TTE Directive).
[2] CENELEC EN 122150: "Sectional Specification: Radio frequency coaxial connectors - Series EIA
flange".
ETSI
---------------------- Page: 6 ----------------------
7 Draft ETSI EN 302 217-2-1 V2.0.1 (2014-08)
[3] CEPT/ERC/DEC(00)07: "ERC Decision of 19 October 2000 on the shared use of the band 17.7 -
19.7 GHz by the fixed service and Earth stations of the fixed-satellite service (space-to-Earth)".
[4] ETSI EN 300 019-1-0: "Environmental Engineering (EE); Environmental conditions and
environmental tests for telecommunications equipment; Part 1-0: Classification of environmental
conditions; Introduction".
[5] ETSI EN 300 019-1-1: "Environmental Engineering (EE); Environmental conditions and
environmental tests for telecommunications equipment; Part 1-1: Classification of environmental
conditions; Storage".
[6] ETSI EN 300 019-1-2: "Environmental Engineering (EE); Environmental conditions and
environmental tests for telecommunications equipment; Part 1-2: Classification of environmental
conditions; Transportation".
[7] ETSI EN 300 019-1-3: "Environmental Engineering (EE); Environmental conditions and
environmental tests for telecommunications equipment; Part 1-3: Classification of environmental
conditions; Stationary use at weatherprotected locations".
[8] ETSI EN 300 019-1-4: "Environmental Engineering (EE); Environmental conditions and
environmental tests for telecommunications equipment; Part 1-4: Classification of environmental
conditions; Stationary use at non-weatherprotected locations".
[9] ETSI EN 300 019-2-0: "Environmental Engineering (EE); Environmental conditions and
environmental tests for telecommunications equipment; Part 2-0: Specification of environmental
tests; Introduction".
[10] ETSI EN 300 019-2-1: "Environmental Engineering (EE); Environmental conditions and
environmental tests for telecommunications equipment; Part 2-1: Specification of environmental
tests; Storage".
[11] ETSI EN 300 019-2-2: "Environmental Engineering (EE); Environmental conditions and
environmental tests for telecommunications equipment; Part 2-2: Specification of environmental
tests; Transportation".
[12] ETSI EN 300 019-2-3: "Environmental Engineering (EE); Environmental conditions and
environmental tests for telecommunications equipment; Part 2-3: Specification of environmental
tests; Stationary use at weatherprotected locations".
[13] ETSI EN 300 019-2-4: "Environmental Engineering (EE); Environmental conditions and
environmental tests for telecommunications equipment; Part 2-4: Specification of environmental
tests; Stationary use at non-weatherprotected locations".
[14] ETSI EN 301 126-1: "Fixed Radio Systems; Conformance testing; Part 1: Point-to-Point
equipment - Definitions, general requirements and test procedures".
[15] ETSI EN 302 217-1: "Fixed Radio Systems; Characteristics and requirements for point-to-point
equipment and antennas; Part 1: Overview and system-independent common characteristics".
[16] ETSI EN 302 217-2-2: "Fixed Radio Systems; Characteristics and requirements for point-to-point
equipment and antennas; Part 2-2: Digital systems operating in frequency bands where frequency
co-ordination is applied; Harmonized EN covering the essential requirements of Article 3.2 of the
R&TTE Directive".
[17] IEC 60153-2: "Hollow metallic waveguides. Part 2: Relevant specifications for ordinary
rectangular waveguides".
[18] IEC 60154-2: "Flanges for waveguides. Part 2: Relevant specifications for flanges for ordinary
rectangular waveguides".
[19] IEC 60169-1: "Radio-frequency connectors. Part 1: General requirements and measuring
methods".
[20] IEC 60339 (all parts): "General purpose rigid coaxial transmission lines and their associated flange
connectors".
ETSI
---------------------- Page: 7 ----------------------
8 Draft ETSI EN 302 217-2-1 V2.0.1 (2014-08)
[21] IEC 60835-2-4: "Methods of measurement for equipment used in digital microwave radio
transmission systems - Part 2: Measurements on terrestrial radio-relay systems -
Section 4: Transmitter/receiver including modulator/demodulator".
[22] IEC 60835-2-8: "Methods of measurement for equipment used in digital microwave radio
transmission systems - Part 2: Measurements on terrestrial radio-relay systems -
Section 8: Adaptive equalizer".
[23] IEEE 802.3-2005: "IEEE Standard for Information technology - Telecommunications and
information exchange between systems - Local and metropolitan area networks - Specific
requirements - Part 3: Carrier Sense Multiple Access with Collision Detection (CSMA/CD)
Access Method and Physical Layer Specifications".
[24] IEEE 1802.3-2001: "IEEE Conformance Test Methodology for IEEE Standards for Local and
Metropolitan Area Networks - Specific Requirements - Part 3: Carrier Sense Multiple Access with
Collision Detection (CSMA/CD) Access Method and Physical Layer Specifications".
[25] Void.
[26] Recommendation ITU-R F.1093-2: "Effects of multipath propagation on the design and operation
of line-of-sight digital fixed wireless systems.
[27] Void.
[28] Recommendation ITU-T O.151: "Error performance measuring equipment operating at the
primary rate and above".
[29] Recommendation ITU-T O.181: "Equipment to assess error performance on STM-N interfaces".
[30] Recommendation ITU-T O.191: "Equipment to measure the cell transfer performance of ATM
connections".
2.2 Informative references
The following referenced documents are not necessary for the application of the present document but they assist the
user with regard to a particular subject area.
[i.1] ECC/REC(02)06: "Channel arrangements for digital Fixed Service Systems operating in the
frequency range 7125-8500 MHz".
[i.2] ERC/REC 12-03: "Harmonised radio frequency channel arrangements for digital terrestrial fixed
systems operating in the band 17.7 GHz TO 19.7 GHz".
[i.3] ERC/REC 14-01: "Radio-frequency channel arrangements for high capacity analogue and digital
radio-relay systems operating in the band 5925 MHz - 6425 MHz".
[i.4] ERC/REC 14-02: "Radio-frequency channel arrangements for high, medium and low capacity
digital fixed service systems operating in the band 6425-7125 MHz".
[i.5] ETSI TR 101 036-1: "Fixed Radio Systems; Generic wordings for standards on DFRS (Digital
Fixed Radio Systems) characteristics; Part 1: General aspects and point-to-point equipment
parameters".
[i.6] ETSI TR 101 506: "Fixed Radio Systems; Generic definitions, terminology and applicability of
essential requ
...
SLOVENSKI STANDARD
oSIST prEN 302 217-2-1 V2.0.1:2014
01-oktober-2014
)LNVQLUDGLMVNLVLVWHPL.DUDNWHULVWLNHLQ]DKWHYH]DRSUHPRLQDQWHQHWLSDWRþND
WRþNDGHO 6LVWHPVNRRGYLVQH]DKWHYH]DGLJLWDOQHVLVWHPHNLGHOXMHMRY
IUHNYHQþQLKSDVRYLKNMHUVHXSRUDEOMDIUHNYHQþQDNRRUGLQDFLMD
Fixed Radio Systems - Characteristics and requirements for point-to-point equipment
and antennas - Part 2-1: System-dependent requirements for digital systems operating in
frequency bands where frequency co-ordination is applied
Ta slovenski standard je istoveten z: EN 302 217-2-1 Version 2.0.1
ICS:
33.060.30 Radiorelejni in fiksni satelitski Radio relay and fixed satellite
komunikacijski sistemi communications systems
33.120.40 Antene Aerials
oSIST prEN 302 217-2-1 V2.0.1:2014 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN 302 217-2-1 V2.0.1:2014
---------------------- Page: 2 ----------------------
oSIST prEN 302 217-2-1 V2.0.1:2014
Draft ETSI EN 302 217-2-1 V2.0.1 (2014-08)
EUROPEAN STANDARD
Fixed Radio Systems;
Characteristics and requirements
for point-to-point equipment and antennas;
Part 2-1: System-dependent requirements
for digital systems operating in frequency bands
where frequency co-ordination is applied
---------------------- Page: 3 ----------------------
oSIST prEN 302 217-2-1 V2.0.1:2014
2 Draft ETSI EN 302 217-2-1 V2.0.1 (2014-08)
Reference
REN/ATTM-04017
Keywords
DFRS, digital, DRRS, FWA, point-to-point, radio,
regulation, transmission
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
http://portal.etsi.org/chaircor/ETSI_support.asp
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2014.
All rights reserved.
TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.
TM
3GPP and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI
---------------------- Page: 4 ----------------------
oSIST prEN 302 217-2-1 V2.0.1:2014
3 Draft ETSI EN 302 217-2-1 V2.0.1 (2014-08)
Contents
Intellectual Property Rights . 5
Foreword . 5
Modal verbs terminology . 5
Introduction . 5
1 Scope . 6
2 References . 6
2.1 Normative references . 6
2.2 Informative references . 8
3 Definitions, symbols and abbreviations . 9
3.1 Definitions . 9
3.2 Symbols . 9
3.3 Abbreviations . 9
4 General characteristics . 9
4.1 Frequency bands and channel arrangements . 9
4.2 Special compatibility requirements between systems . 10
4.3 Transmission capacity and spectral efficiency . 10
5 Main requirements . 10
5.1 System nominal loading . 10
5.2 Environmental profile . 11
5.3 Transmitter characteristics. 11
5.3.1 Transmitter power and power tolerance . 11
5.3.1.1 Maximum power . 11
5.3.1.2 Transmitter output power tolerance . 11
5.3.2 Transmitter power and frequency control . 12
5.3.2.1 Transmitter power control (ATPC and RTPC) . 12
5.3.2.1.1 Automatic Transmitter Power Control (ATPC) . 12
5.3.2.1.2 Remote Transmitter Power Control (RTPC) . 13
5.3.2.2 Remote Frequency Control (RFC) . 13
5.3.3 Radio Frequency (RF) spectrum mask. 13
5.3.4 Discrete CW components exceeding the spectrum mask limit . 13
5.3.4.1 Discrete CW components at the symbol rate . 13
5.3.4.2 Other discrete CW components exceeding the spectrum mask limit . 13
5.3.5 Spurious emissions - external . 13
5.3.6 Radio frequency tolerance . 13
5.4 Receiver characteristics . 14
5.4.1 Spurious emissions-external . 14
5.5 System performance without diversity . 14
5.5.1 BER as a function of receiver signal level . 14
5.5.2 Interference sensitivity . 14
5.5.2.1 Co-channel "external" interference sensitivity . 14
5.5.2.2 Adjacent channel interference sensitivity . 14
5.5.2.3 CW spurious interference . 14
6 Complementary requirements . 15
6.1 Branching/feeder requirements . 15
6.1.1 Waveguide flanges (or other connectors) . 15
6.1.2 Return loss of feeder/antenna systems at equipment antenna port (C/C' reference point) . 16
6.2 Intermodulation products . 16
6.3 Transmitter characteristics. 17
6.3.1 Spurious emissions - internal . 17
6.3.2 Radio Frequency (RF) spectrum mask when mixed supplier compatibility is required . 17
6.4 Receiver characteristics . 18
ETSI
---------------------- Page: 5 ----------------------
oSIST prEN 302 217-2-1 V2.0.1:2014
4 Draft ETSI EN 302 217-2-1 V2.0.1 (2014-08)
6.4.1 Maximum input level and input level range . 18
6.4.2 Spurious emissions - internal . 19
6.4.3 Image rejection . 19
6.4.4 Innermost channel selectivity . 20
6.5 System performance without diversity . 20
6.5.1 Equipment Residual BER (RBER) . 20
6.5.2 Distortion sensitivity . 22
6.5.2.1 Introduction . 22
6.5.2.2 Requirement . 22
6.5.2.3 Assessment . 23
6.5.3 Interference sensitivity for CCDP with XPIC operation . 24
6.5.3.1 General . 24
6.5.3.2 Co-channel "internal" interference sensitivity in flat fading conditions . 24
6.6 System characteristics with diversity . 24
6.6.1 Differential delay compensation . 24
6.6.2 BER performance . 24
Annex A (normative): Spectrum masks and receiver selectivity when mixed supplier
compatibility is required . 25
A.0 Introduction . 25
A.1 TX masks assessment . 26
A.2 Normal channels - Emission mask floor . 26
A.2.1 RBER impact . 26
A.2.2 Local TX to RX compatibility . 26
A.2.2.1 Spectrum mask . 26
A.2.2.2 Receiver selectivity . 27
A.3 Innermost channels for channel arrangements from about 4 GHz to about 8,5 GHz with channel
separation of 28 MHz to 30 MHz . 27
A.3.1 Innermost channels spectrum masks . 27
A.3.2 Receiver innermost channel selectivity . 29
A.4 Innermost channels for channel arrangements from about 4 GHz to 11 GHz with channel
separation of 40 MHz . 30
A.4.1 Innermost channels spectrum masks . 30
A.4.2 Receiver innermost channels selectivity . 31
A.5 Innermost channels for 18 GHz channel arrangements with channel separation of 55 MHz . 32
A.5.1 Innermost channels spectrum masks . 32
A.5.2 Receiver innermost channels selectivity . 33
Annexes B to E: Deleted and left void . 35
Annex F (normative): Definition of equivalent data rates for packet data, PDH/SDH and
other signals on the traffic interface. 36
Annex G (informative): Additional information . 37
G.1 Residual Bit Error Ratio (RBER) and Residual Frame Error Ratio (RFER) . 37
G.2 Measurement test set for XPI characteristics . 38
G.3 Differential delay compensation range . 39
G.4 FER/BER equivalence and FER performance measurement equipment settings (example) . 40
G.4.1 FER/BER equivalence . 40
G.4.2 FER equipment settings and measurement techniques (example) . 41
G.5 Automatic Transmitter Power Control (ATPC) . 41
Annex H (informative): Mitigation techniques referred in ERC/DEC(00)07 (18 GHz band) . 43
Annex I (informative): Change History . 44
History . 45
ETSI
---------------------- Page: 6 ----------------------
oSIST prEN 302 217-2-1 V2.0.1:2014
5 Draft ETSI EN 302 217-2-1 V2.0.1 (2014-08)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (http://ipr.etsi.org).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This draft European Standard (EN) has been produced by ETSI Technical Committee Access, Terminals, Transmission
and Multiplexing (ATTM), and is now submitted for the combined Public Enquiry and Vote phase of the ETSI
standards EN Approval Procedure.
The present document is part 2-1 of a multi-part deliverable covering the Fixed Radio Systems; Characteristics and
requirements for point-to-point equipment and antennas. Full details of the entire series can be found in part 1 [15].
Proposed national transposition dates
Date of latest announcement of this EN (doa): 3 months after ETSI publication
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 6 months after doa
Date of withdrawal of any conflicting National Standard (dow): 6 months after doa
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "may not", "need", "need not", "will",
"will not", "can" and "cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms
for the expression of provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
Introduction
The introduction of EN 302 217-1 [15] applies.
ETSI
---------------------- Page: 7 ----------------------
oSIST prEN 302 217-2-1 V2.0.1:2014
6 Draft ETSI EN 302 217-2-1 V2.0.1 (2014-08)
1 Scope
The present document summarizes all system-dependent requirements for Point-to-Point (P-P) equipment in
applications deployed in bands where frequency co-ordination is generally applied. These requirements are introduced
in two different clauses sub-sets:
• Main requirements are requirements that are also related to the "essential requirements" under article 3.2 of
the R&TTE Directive [1] and further detailed in the Harmonized Standard EN 302 217-2-2 [16].
• Complementary requirements are requirements that are not related to essential requirements under
article 3.2 of the R&TTE Directive [1]. Nevertheless they have been commonly agreed for proper system
operation and deployment when specific deployment conditions or compatibility requirements are present.
Compliance to all or some of these requirements is left to supplier decision.
Description and limits for parameters relevant to essential requirements under article 3.2 of R&TTE Directive [1] are
given in the Harmonized Standard EN 302 217-2-2 [16].
For other system-dependent parameters where standardization is required but that do not affect the R&TTE Directive
"essential requirements" mentioned above, description and limits are detailed in the present document in clause 6 and in
the annex A, annex F and annex G.
The present document deals with Radio Frequency (RF) and base-band equipment characteristics; antenna system
requirements are covered in EN 302 217-4-1 [i.9] and EN 302 217-4-2 [i.10].
The present document does not cover test procedures and test conditions which are set out in EN 301 126-1 [14].
As the maximum transmission rate in a given bandwidth depends on system spectral efficiency, equipment are
subdivided in different spectral efficiency classes as defined in EN 302 217-2-2 [16].
The spectral efficiency classes are indicative only and do not imply any constraint to the actual modulation format,
provided that all the requirements in the relevant parts of this Multi-part deliverable for the declared class are met.
Guidance on the definition of radio parameters relevant to the essential requirements under article 3.2 of R&TTE
Directive [1] for DFRS may be found in TR 101 506 [i.6].
Technical background for most of the parameters and requirements referred to in this Multi-part deliverable may be
found in TR 101 036-1 [i.5].
2 References
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
reference document (including any amendments) applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
http://docbox.etsi.org/Reference.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
2.1 Normative references
The following referenced documents are necessary for the application of the present document.
[1] Directive 1999/5/EC of the European Parliament and of the Council of 9 March 1999 on radio
equipment and telecommunications terminal equipment and the mutual recognition of their
conformity (R&TTE Directive).
[2] CENELEC EN 122150: "Sectional Specification: Radio frequency coaxial connectors - Series EIA
flange".
ETSI
---------------------- Page: 8 ----------------------
oSIST prEN 302 217-2-1 V2.0.1:2014
7 Draft ETSI EN 302 217-2-1 V2.0.1 (2014-08)
[3] CEPT/ERC/DEC(00)07: "ERC Decision of 19 October 2000 on the shared use of the band 17.7 -
19.7 GHz by the fixed service and Earth stations of the fixed-satellite service (space-to-Earth)".
[4] ETSI EN 300 019-1-0: "Environmental Engineering (EE); Environmental conditions and
environmental tests for telecommunications equipment; Part 1-0: Classification of environmental
conditions; Introduction".
[5] ETSI EN 300 019-1-1: "Environmental Engineering (EE); Environmental conditions and
environmental tests for telecommunications equipment; Part 1-1: Classification of environmental
conditions; Storage".
[6] ETSI EN 300 019-1-2: "Environmental Engineering (EE); Environmental conditions and
environmental tests for telecommunications equipment; Part 1-2: Classification of environmental
conditions; Transportation".
[7] ETSI EN 300 019-1-3: "Environmental Engineering (EE); Environmental conditions and
environmental tests for telecommunications equipment; Part 1-3: Classification of environmental
conditions; Stationary use at weatherprotected locations".
[8] ETSI EN 300 019-1-4: "Environmental Engineering (EE); Environmental conditions and
environmental tests for telecommunications equipment; Part 1-4: Classification of environmental
conditions; Stationary use at non-weatherprotected locations".
[9] ETSI EN 300 019-2-0: "Environmental Engineering (EE); Environmental conditions and
environmental tests for telecommunications equipment; Part 2-0: Specification of environmental
tests; Introduction".
[10] ETSI EN 300 019-2-1: "Environmental Engineering (EE); Environmental conditions and
environmental tests for telecommunications equipment; Part 2-1: Specification of environmental
tests; Storage".
[11] ETSI EN 300 019-2-2: "Environmental Engineering (EE); Environmental conditions and
environmental tests for telecommunications equipment; Part 2-2: Specification of environmental
tests; Transportation".
[12] ETSI EN 300 019-2-3: "Environmental Engineering (EE); Environmental conditions and
environmental tests for telecommunications equipment; Part 2-3: Specification of environmental
tests; Stationary use at weatherprotected locations".
[13] ETSI EN 300 019-2-4: "Environmental Engineering (EE); Environmental conditions and
environmental tests for telecommunications equipment; Part 2-4: Specification of environmental
tests; Stationary use at non-weatherprotected locations".
[14] ETSI EN 301 126-1: "Fixed Radio Systems; Conformance testing; Part 1: Point-to-Point
equipment - Definitions, general requirements and test procedures".
[15] ETSI EN 302 217-1: "Fixed Radio Systems; Characteristics and requirements for point-to-point
equipment and antennas; Part 1: Overview and system-independent common characteristics".
[16] ETSI EN 302 217-2-2: "Fixed Radio Systems; Characteristics and requirements for point-to-point
equipment and antennas; Part 2-2: Digital systems operating in frequency bands where frequency
co-ordination is applied; Harmonized EN covering the essential requirements of Article 3.2 of the
R&TTE Directive".
[17] IEC 60153-2: "Hollow metallic waveguides. Part 2: Relevant specifications for ordinary
rectangular waveguides".
[18] IEC 60154-2: "Flanges for waveguides. Part 2: Relevant specifications for flanges for ordinary
rectangular waveguides".
[19] IEC 60169-1: "Radio-frequency connectors. Part 1: General requirements and measuring
methods".
[20] IEC 60339 (all parts): "General purpose rigid coaxial transmission lines and their associated flange
connectors".
ETSI
---------------------- Page: 9 ----------------------
oSIST prEN 302 217-2-1 V2.0.1:2014
8 Draft ETSI EN 302 217-2-1 V2.0.1 (2014-08)
[21] IEC 60835-2-4: "Methods of measurement for equipment used in digital microwave radio
transmission systems - Part 2: Measurements on terrestrial radio-relay systems -
Section 4: Transmitter/receiver including modulator/demodulator".
[22] IEC 60835-2-8: "Methods of measurement for equipment used in digital microwave radio
transmission systems - Part 2: Measurements on terrestrial radio-relay systems -
Section 8: Adaptive equalizer".
[23] IEEE 802.3-2005: "IEEE Standard for Information technology - Telecommunications and
information exchange between systems - Local and metropolitan area networks - Specific
requirements - Part 3: Carrier Sense Multiple Access with Collision Detection (CSMA/CD)
Access Method and Physical Layer Specifications".
[24] IEEE 1802.3-2001: "IEEE Conformance Test Methodology for IEEE Standards for Local and
Metropolitan Area Networks - Specific Requirements - Part 3: Carrier Sense Multiple Access with
Collision Detection (CSMA/CD) Access Method and Physical Layer Specifications".
[25] Void.
[26] Recommendation ITU-R F.1093-2: "Effects of multipath propagation on the design and operation
of line-of-sight digital fixed wireless systems.
[27] Void.
[28] Recommendation ITU-T O.151: "Error performance measuring equipment operating at the
primary ra
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.