ETSI EN 302 065 V1.2.1 (2010-10)
Electromagnetic compatibility and Radio spectrum Matters (ERM); Short Range Devices (SRD) using Ultra Wide Band technology (UWB) for communications purposes; Harmonized EN covering the essential requirements of article 3.2 of the R&TTE Directive
Electromagnetic compatibility and Radio spectrum Matters (ERM); Short Range Devices (SRD) using Ultra Wide Band technology (UWB) for communications purposes; Harmonized EN covering the essential requirements of article 3.2 of the R&TTE Directive
REN/ERM-TGUWB-0118-1
Elektromagnetna združljivost in zadeve v zvezi z radijskim spektrom (ERM) - Naprave kratkega dosega (SRD), ki uporabljajo ultra širokopasovno (UWB) tehnologijo za komuniciranje - Harmonizirani EN, ki zajema bistvene zahteve člena 3.2 direktive R&TTE
Pričujoči dokument velja za sprejemnike-oddajnike, sprejemnike in oddajnike, ki uporabljajo ultra širokopasovne (UWB) tehnologije in se uporabljajo za namene komunikacije kratkega dosega. Pričujoči dokument velja za impulzne, spremenjene impulzne in UWB komunikacijske tehnologije, osnovane na RF nosilcih.
Pričujoči dokument velja za fiksne (samo v zaprtih prostorih), mobilne ali prenosne uporabe, v npr.:
- samostoječi radijski opremi z ali brez lastnih določb glede nadzora;
- vtičnih radijskih napravah, namenjenih za uporabo z ali znotraj različnih gostiteljskih sistemov, npr. osebni računalniki, ročni terminali itd.;
- vtičnih radijskih napravah, namenjenih za uporabo z kombinirano opremo, npr. ožičeni modemi, digitalni sprejemniki, dostopne točke itd.;
- kombinirani opremi ali kombinaciji vtičnih radijskih naprav in določene vrste gostiteljske opreme;
- opremi za uporabo v cestnih in železniških vozilih.
OPOMBA 1: Glede na ECC/DEC/(06)04 in Odločbo 2007/131/ES [i.5] ter njeno dopolnilo, UWB oddajna oprema za uporabo pri letečih modelčkih, zračnih plovilih ali drugih vrstah letalstva, v skladu z pričujočim dokumentom ne sme biti postavljena na fiksni zunanji lokaciji. Pričujoči dokument velja za UWB opremo z izhodno povezavo, uporabljeno z namensko anteno ali UWB opremo z vgrajeno anteno. Ti tipi radijske opreme so zmožni delovanja v vseh ali katerem koli delu frekvenčnih pasov, kot so navedeni v preglednici 1.
General Information
Buy Standard
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Electromagnetic compatibility and Radio spectrum Matters (ERM) - Short Range Devices (SRD) using Ultra Wide Band technology (UWB) for communications purposes - Harmonized EN covering essential requirements of article 3.2 of the R&TTE Directive33.100.01Elektromagnetna združljivost na splošnoElectromagnetic compatibility in general33.060.99Druga oprema za radijske komunikacijeOther equipment for radiocommunicationsICS:Ta slovenski standard je istoveten z:EN 302 065 Version 1.2.1SIST EN 302 065 V1.2.1:2010en01-december-2010SIST EN 302 065 V1.2.1:2010SLOVENSKI
STANDARD
ETSI EN 302 065 V1.2.1 (2010-10)Harmonized European Standard (Telecommunications series) Electromagnetic compatibility andRadio spectrum Matters (ERM);Short Range Devices (SRD) usingUltra Wide Band technology (UWB)for communications purposes;Harmonized EN covering the essential requirementsof article 3.2 of the R&TTE Directive SIST EN 302 065 V1.2.1:2010
ETSI ETSI EN 302 065 V1.2.1 (2010-10) 2
Reference REN/ERM-TGUWB-0118-1 Keywords radio, SRD, testing, UWB ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00
Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C Association à but non lucratif enregistrée à la Sous-Préfecture de Grasse (06) N° 7803/88
Important notice Individual copies of the present document can be downloaded from: http://www.etsi.org The present document may be made available in more than one electronic version or in print. In any case of existing or perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF). In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at http://portal.etsi.org/tb/status/status.asp If you find errors in the present document, please send your comment to one of the following services: http://portal.etsi.org/chaircor/ETSI_support.asp Copyright Notification No part may be reproduced except as authorized by written permission. The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2010. All rights reserved.
DECTTM, PLUGTESTSTM, UMTSTM, TIPHONTM, the TIPHON logo and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members. 3GPPTM is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. LTE™ is a Trade Mark of ETSI currently being registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association. SIST EN 302 065 V1.2.1:2010
ETSI ETSI EN 302 065 V1.2.1 (2010-10) 3 Contents Intellectual Property Rights . 6 Foreword . 6 Introduction . 7 1 Scope . 9 2 References . 9 2.1 Normative references . 10 2.2 Informative references . 10 3 Definitions, symbols and abbreviations . 11 3.1 Definitions . 11 3.2 Symbols . 12 3.3 Abbreviations . 12 4 Technical requirements specification . 13 4.1 Technical requirements . 13 4.1.1 Operating bandwidth. 13 4.1.1.1 Definition . 13 4.1.1.2 Test procedure . 13 4.1.1.3 Limit . 13 4.1.1.4 Measurement uncertainty . 13 4.1.2 Maximum value of mean power spectral density . 14 4.1.2.1 Definition . 14 4.1.2.2 Test procedure . 14 4.1.2.3 Limit . 14 4.1.2.4 Maximum allowable measurement uncertainty. 15 4.1.3 Maximum value of peak power . 15 4.1.3.1 Definition . 15 4.1.3.2 Test procedure . 15 4.1.3.3 Limit . 15 4.1.3.4 Maximum allowable measurement uncertainty. 16 4.1.4 Transmit Power Control . 16 4.1.4.1 Definition . 16 4.1.4.2 Test procedure . 16 4.1.4.3 Limit . 16 4.1.4.4 Maximum allowable measurement uncertainty. 17 4.1.5 Receiver spurious emissions . 17 4.1.5.1 Definition . 17 4.1.5.2 Test procedure . 17 4.1.5.3 Limit . 17 4.1.5.4 Maximum allowable measurement uncertainty. 17 4.1.6 Detect-And-Avoid (DAA) . 17 4.1.6.1 Introduction . 17 4.1.6.1.1 Applicable frequency ranges . 18 4.1.6.1.2 DAA operational modes . 18 4.1.6.2 Test procedure . 18 4.1.6.3 Limit . 18 4.1.6.4 Maximum allowable measurement uncertainty. 18 4.1.7 Low Duty Cycle (LDC) . 19 4.1.7.1 Definitions . 19 4.1.7.2 Test procedure . 19 4.1.7.3 Limits . 19 4.1.8 Equivalent mitigation techniques . 19 5 Essential radio test suites . 19 5.1 Product information . 19 5.2 Requirements for the test modulation . 20 SIST EN 302 065 V1.2.1:2010
ETSI ETSI EN 302 065 V1.2.1 (2010-10) 4 5.3 Test conditions, power supply and ambient temperatures . 20 5.3.1 Test conditions . 20 5.3.2 Power sources . 21 5.3.2.1 Power sources for stand-alone equipment . 21 5.3.2.2 Power sources for plug-in radio devices . 21 5.3.3 Normal test conditions . 21 5.3.3.1 Normal temperature and humidity . 21 5.3.3.2 Normal power source . 21 5.3.3.2.1 Mains voltage . 21 5.3.3.2.2 Lead-acid battery power sources used on vehicles . 21 5.3.3.2.3 Other power sources . 21 5.4 Choice of equipment for test suites . 22 5.4.1 Choice of model . 22 5.4.2 Presentation. 22 5.4.3 Operating bandwidth and multiband equipment . 22 5.4.4 Test sites and general arrangements for radiated measurements . 22 5.5 Testing of host connected equipment and plug-in radio devices . 23 5.5.1 The use of a host or test fixture for testing plug-In radio devices . 23 5.5.2 Testing of combinations . 23 5.5.2.1 Alternative A: General approach for combinations . 23 5.5.2.2 Alternative B: For host equipment with a plug-in radio device . 23 5.5.2.3 Alternative C: For combined equipment with a plug-in radio device . 23 5.6 Interpretation of the measurement results . 23 5.6.1 Measurement uncertainty is equal to or less than maximum acceptable uncertainty . 24 5.6.2 Measurement uncertainty is greater than maximum acceptable uncertainty . 24 5.7 Other emissions . 25 5.8 Test procedures for essential radio test suites. 25 5.8.1 General . 25 5.8.2 Maximum mean power spectral density . 25 5.8.3 Maximum peak power . 26 5.8.4 Operating bandwidth. 27 5.8.5 Receiver spurious emissions . 27 5.8.6 Low Duty Cycle . 28 5.8.7 Test Procedure for the radiolocation systems DAA test . 28 5.8.7.1 Introduction . 28 5.8.7.2 Initial Start-up test . 30 5.8.7.2.1 Test without a radiolocation test signal during the Minimum Initial Channel Availability Check Time, Tavail_time_min . 30 5.8.7.2.2 Tests with a radiolocation test signal at the beginning of the Minimum Initial Channel Availability Check Time, Tavail_time_min . 31 5.8.7.2.3 Tests with radiolocation test signal at the end of the Minimum Initial Channel Availability Check Time, Tavail_time_min . 33 5.8.7.3 In-operation test . 35 5.8.7.3.1 In-operation test procedure . 35 5.8.7.4 Test patterns for the radiolocation DAA test . 36 5.8.8 Test Procedure for BWA systems in the band 3,4 GHz to 3,8 GHz . 38 5.8.8.1 Introduction . 38 5.8.8.1.1 UWB radio devices with and without victim service identification . 38 5.8.8.2 Initial start-up test . 38 5.8.8.2.1 Test without a BWA test signal during the Minimum Initial Channel Availability Check Time, Tavail_time_min . 38 5.8.8.2.2 Tests with a BWA test signal at the beginning of the Minimum Initial Channel Availability Check Time, Tavail_time . 39 5.8.8.2.3 Tests with a BWA test signal at the end of the Minimum Initial Channel Availability Check Time, Tavail_time . 40 5.8.8.3 In-operation test . 41 5.8.8.4 Test Patterns for BWA Testing . 43 Annex A (normative): HS Requirements and conformance Test specifications Table (HS-RTT) . 45 Annex B (normative): Radiated measurements . 48 SIST EN 302 065 V1.2.1:2010
ETSI ETSI EN 302 065 V1.2.1 (2010-10) 5 B.1 Test sites and general arrangements for measurements involving the use of radiated fields . 48 B.1.1 Anechoic chamber . 48 B.1.2 Anechoic chamber with a conductive ground plane . 49 B.1.3 Test antenna . 51 B.1.4 Substitution antenna . 51 B.1.5 Measuring antenna . 51 B.2 Guidance on the use of a radiation test site . 51 B.2.1 Verification of the test site . 51 B.2.2 Preparation of the EUT . 52 B.2.3 Power supplies to the EUT . 52 B.2.4 Range length . 52 B.2.5 Site preparation . 53 B.3 Coupling of signals . 53 B.3.1 General . 53 B.3.2 Data Signals. 53 B.4 Standard test methods . 53 B.4.1 Calibrated setup . 53 B.4.2 Substitution method . 54 B.5 Standard calibration method . 55 Annex C (normative): Conducted measurements for DAA testing . 57 Annex D (informative): Measurement antenna and preamplifier specifications . 58 Annex E (normative): Radiolocation services in the band 3,1 GHz to 3,4 GHz . 59 Annex F (normative): Broadband wireless access services in the band 3,4 GHz to 3,8 GHz . 60 Annex G (normative): Radiolocation services in the band 8,5 GHz to 9,0 GHz . 61 Annex H (informative): Calculation of peak limit for 3 MHz measurement bandwidth . 62 Annex I (normative): ICS Proforma for DAA radio device . 64 I.1 Identification of the protocol . 64 I.2 ICS proforma tables. 64 I.2.1 Avoidance Modes . 64 Annex J (informative): Bibliography . 65 Annex K (informative): The EN title in the official languages . 66 History . 67
SIST EN 302 065 V1.2.1:2010
ETSI ETSI EN 302 065 V1.2.1 (2010-10) 6 Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (http://webapp.etsi.org/IPR/home.asp). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This Harmonized European Standard (Telecommunications series) has been produced by ETSI Technical Committee Electromagnetic compatibility and Radio spectrum Matters (ERM). The present document has been produced by ETSI in response to a mandate from the European Commission issued under Council Directive 98/34/EC [i.2] (as amended) laying down a procedure for the provision of information in the field of technical standards and regulations. The present document is intended to become a Harmonized Standard, the reference of which will be published in the Official Journal of the European Communities referencing the Directive 1999/5/EC [i.3] of the European Parliament and of the Council of 9 March 1999 on radio equipment and telecommunications terminal equipment and the mutual recognition of their conformity ("the R&TTE Directive"). The present document is intended to cover the provisions of article 3.2 of Directive 1999/5/EC (R&TTE Directive) [i.3]. The present document does not apply to radio equipment for which a specific Harmonized EN applies as such Harmonized EN may specify additional EN requirements relevant to the presumption of conformity under article 3.2 of the R&TTE Directive. Technical specifications relevant to Directive 1999/5/EC [i.3] are summarised in annex A.
National transposition dates Date of adoption of this EN: 20 September 2010 Date of latest announcement of this EN (doa): 31 December 2010 Date of latest publication of new National Standard or endorsement of this EN (dop/e):
30 June 2011 Date of withdrawal of any conflicting National Standard (dow): 30 June 2012
SIST EN 302 065 V1.2.1:2010
ETSI ETSI EN 302 065 V1.2.1 (2010-10) 7 Introduction The present document is part of a set of standards developed by ETSI and is designed to fit in a modular structure to cover all radio and telecommunications terminal equipment within the scope of the R&TTE Directive. The modular structure is shown in EG 201 399 [i.1]. UWB Technologies The present document provides a generic set of technical requirements covering many different types of UWB technologies used for short range communications. These technologies can be broken down into two groups: 1) Impulse based technologies; and 2) RF carrier based technologies. The following clauses give a brief overview of these UWB technologies and their associated modulation techniques. Impulse technology Impulse derived UWB technology consists of a series of impulses created from a dc voltage step whose rise time can be modified to provide the maximum useful number of spectral emission frequencies. This derived impulse can then be suitably modified by the use of filters to locate the resulting waveform within a specific frequency spectrum range. This filter can be a standalone filter or incorporated into an antenna design to reduce emissions outside the designated frequency spectrum. Modulation techniques include pulse positioning in time, pulse suppression and other techniques to convey information. The transmitted energy is summed at the receiver to reproduce the transmitted pulse. This technology is suitable for direct and non-direct line of sight communications, any reflected or time delayed emissions being suppressed by the receiver input circuits. RF carrier based technology RF carrier based UWB technology is based upon classical radio carrier technology suitably modulated by a baseband modulating process. The modulating process must produce a bandwidth in excess of 50 MHz to be defined as UWB. Different modulating processes are used to transmit the data information to the receiver and can consist of a series of single hopping frequencies or multi-tone carriers. This technology can be used for both direct and non-direct line of sight communications, any reflected or time delayed emissions being suppressed by the receiver input circuits. Test and measurement limitations The ERA report 2006-0713 [i.9] has shown that there are practical limitations on measurements of RF radiated emissions. The minimum radiated levels that can be practically measured in the lower GHz frequenc
...
Draft ETSI EN 302 065 V1.2.1 (2009-12)
Harmonized European Standard (Telecommunications series)
Electromagnetic compatibility and
Radio spectrum Matters (ERM);
Short Range Devices (SRD) using
Ultra Wide Band technology (UWB)
for communications purposes;
Harmonized EN covering essential requirements
of article 3.2 of the R&TTE Directive
---------------------- Page: 1 ----------------------
2 Draft ETSI EN 302 065 V1.2.1 (2009-12)
Reference
REN/ERM-TGUWB-0118-1
Keywords
radio, SRD, testing, UWB
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
Individual copies of the present document can be downloaded from:
http://www.etsi.org
The present document may be made available in more than one electronic version or in print. In any case of existing or
perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF).
In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive
within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
http://portal.etsi.org/chaircor/ETSI_support.asp
Copyright Notification
No part may be reproduced except as authorized by written permission.
The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2009.
All rights reserved.
TM TM TM TM
DECT , PLUGTESTS , UMTS , TIPHON , the TIPHON logo and the ETSI logo are Trade Marks of ETSI registered
for the benefit of its Members.
TM
3GPP is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners.
LTE™ is a Trade Mark of ETSI currently being registered
for the benefit of its Members and of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI
---------------------- Page: 2 ----------------------
3 Draft ETSI EN 302 065 V1.2.1 (2009-12)
Contents
Intellectual Property Rights . 6
Foreword . 6
Introduction . 7
1 Scope . 9
2 References . 9
2.1 Normative references . 10
2.2 Informative references . 10
3 Definitions, symbols and abbreviations . 11
3.1 Definitions . 11
3.2 Symbols . 12
3.3 Abbreviations . 12
4 Technical requirements specification . 13
4.1 Technical requirements . 13
4.1.1 Operating bandwidth. 13
4.1.1.1 Definition . 13
4.1.1.2 Test procedure . 13
4.1.1.3 Limit . 13
4.1.1.4 Measurement uncertainty . 14
4.1.2 Maximum value of mean power spectral density . 14
4.1.2.1 Definition . 14
4.1.2.2 Test procedure . 14
4.1.2.3 Limit . 14
4.1.2.4 Maximum allowable measurement uncertainty. 15
4.1.3 Maximum value of peak power . 15
4.1.3.1 Definition . 15
4.1.3.2 Test procedure . 15
4.1.3.3 Limit . 15
4.1.3.4 Maximum allowable measurement uncertainty. 16
4.1.4 Transmit Power Control . 16
4.1.4.1 Definition . 16
4.1.4.2 Test procedure . 16
4.1.4.3 Limit . 17
4.1.4.4 Maximum allowable measurement uncertainty. 17
4.1.5 Receiver spurious emissions . 17
4.1.5.1 Definition . 17
4.1.5.2 Test procedure . 17
4.1.5.3 Limit . 17
4.1.5.4 Maximum allowable measurement uncertainty. 18
4.1.6 Detect-And-Avoid (DAA) . 18
4.1.6.1 Introduction . 18
4.1.6.1.1 Applicable frequency ranges . 18
4.1.6.1.2 DAA operational modes . 18
4.1.6.2 Test procedure . 19
4.1.6.3 Limit . 19
4.1.6.4 Maximum allowable measurement uncertainty. 19
4.1.7 Low Duty Cycle (LDC) . 19
4.1.7.1 Definitions . 19
4.1.7.2 Test procedure . 19
4.1.7.3 Limits . 19
4.1.8 Equivalent mitigation techniques . 20
5 Essential radio test suites . 20
5.1 Product information . 20
5.2 Requirements for the test modulation . 21
ETSI
---------------------- Page: 3 ----------------------
4 Draft ETSI EN 302 065 V1.2.1 (2009-12)
5.3 Test conditions, power supply and ambient temperatures . 21
5.3.1 Test conditions . 21
5.3.2 Power sources . 21
5.3.2.1 Power sources for stand-alone equipment . 21
5.3.2.2 Power sources for plug-in radio devices . 21
5.3.3 Normal test conditions . 22
5.3.3.1 Normal temperature and humidity . 22
5.3.3.2 Normal power source . 22
5.3.3.2.1 Mains voltage . 22
5.3.3.2.2 Lead-acid battery power sources used on vehicles . 22
5.3.3.2.3 Other power sources . 22
5.4 Choice of equipment for test suites . 22
5.4.1 Choice of model . 22
5.4.2 Presentation. 22
5.4.3 Operating bandwidth. 22
5.4.4 Test sites and general arrangements for radiated measurements . 23
5.5 Testing of host connected equipment and plug-in radio devices . 23
5.5.1 The use of a host or test fixture for testing plug-In radio devices . 23
5.5.2 Testing of combinations . 23
5.5.2.1 Alternative A: General approach for combinations . 23
5.5.2.2 Alternative B: For host equipment with a plug-in radio device . 23
5.5.2.3 Alternative C: For combined equipment with a plug-in radio device . 24
5.6 Interpretation of the measurement results . 24
5.6.1 Measurement uncertainty is equal to or less than maximum acceptable uncertainty . 24
5.6.2 Measurement uncertainty is greater than maximum acceptable uncertainty . 25
5.7 Other emissions . 25
5.8 Test procedures for essential radio test suites. 25
5.8.1 General . 25
5.8.2 Maximum mean power spectral density . 25
5.8.3 Maximum peak power . 27
5.8.4 Operating bandwidth. 27
5.8.5 Receiver spurious emissions . 28
5.8.6 Low Duty Cycle . 28
5.8.7 Test Procedure for the radiolocation systems DAA test . 28
5.8.7.1 Introduction . 28
5.8.7.2 Start-up test . 30
5.8.7.2.1 Test without a radiolocation test signal during the Minimum Initial Channel Availability
Check Time, T . 30
avail_time_min
5.8.7.2.2 Tests with a radiolocation test signal at the beginning of the Minimum Initial Channel
Availability Check Time, T . 31
avail_time_min
5.8.7.2.3 Tests with radiolocation test signal at the end of the Minimum Initial Channel Availability
Check Time, T . 33
avail_time_min
5.8.7.3 In-operation test . 35
5.8.7.3.1 In-operation test procedure . 35
5.8.7.4 Test patterns for the radiolocation DAA test . 36
5.8.8 Test Procedure for BWA systems in the band 3,4 GHz to 3,8 GHz . 37
5.8.8.1 Introduction . 37
5.8.8.1.1 UWB radio devices with and without victim service identification . 37
5.8.8.2 Initial start-up test . 37
5.8.8.2.1 Test without a BWA test signal during the Minimum Initial Channel Availability Check
Time, T . 38
avail_time_min
5.8.8.2.2 Tests with a BWA test signal at the beginning of the Minimum Initial Channel Availability
Check Time, T . 38
avail_time
5.8.8.2.3 Tests with a BWA test signal at the end of the Minimum Initial Channel Availability Check
Time, T . 40
avail_time
5.8.8.3 In-operation test . 41
5.8.8.4 Test Patterns for BWA Testing . 42
Annex A (normative): HS Requirements and conformance Test specifications Table (HS-
RTT) . 44
Annex B (normative): Radiated measurements . 47
ETSI
---------------------- Page: 4 ----------------------
5 Draft ETSI EN 302 065 V1.2.1 (2009-12)
B.1 Test sites and general arrangements for measurements involving the use of radiated fields . 47
B.1.1 Anechoic chamber . 47
B.1.2 Anechoic chamber with a conductive ground plane . 48
B.1.3 Test antenna . 50
B.1.4 Substitution antenna . 50
B.1.5 Measuring antenna . 50
B.2 Guidance on the use of a radiation test site . 50
B.2.1 Verification of the test site . 50
B.2.2 Preparation of the EUT . 51
B.2.3 Power supplies to the EUT . 51
B.2.4 Range length . 51
B.2.5 Site preparation . 52
B.3 Coupling of signals . 52
B.3.1 General . 52
B.3.2 Data Signals. 52
B.4 Standard test methods . 52
B.4.1 Calibrated setup . 52
B.4.2 Substitution method . 53
B.5 Standard calibration method . 54
Annex C (normative): Conducted measurements for DAA testing . 56
Annex D (informative): Measurement antenna and preamplifier specifications . 57
Annex E (normative): Radiolocation services in the band 3,1 GHz to 3,4 GHz . 58
Annex F (normative): Broadband wireless access services in the band 3,4 GHz to 3,8 GHz . 59
Annex G (normative): Radiolocation services in the band 8,5 GHz to 9,0 GHz . 60
Annex H (informative): Calculation of peak limit for 3 MHz measurement bandwidth . 61
Annex I (normative): ICS Proforma for DAA radio device . 63
I.1 Identification of the protocol . 63
I.2 ICS proforma tables. 63
I.2.1 Avoidance Modes . 63
Annex J (informative): Bibliography . 64
Annex K (informative): The EN title in the official languages . 65
History . 66
ETSI
---------------------- Page: 5 ----------------------
6 Draft ETSI EN 302 065 V1.2.1 (2009-12)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (http://webapp.etsi.org/IPR/home.asp).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This Harmonized European Standard (Telecommunications series) has been produced by ETSI Technical Committee
Electromagnetic compatibility and Radio spectrum Matters (ERM), and is now submitted for the Public Enquiry phase
of the ETSI standards Two-step Approval Procedure.
The present document has been produced by ETSI in response to a mandate from the European Commission issued
under Council Directive 98/34/EC [i.2] (as amended) laying down a procedure for the provision of information in the
field of technical standards and regulations.
The present document is intended to become a Harmonized Standard, the reference of which will be published in the
Official Journal of the European Communities referencing the Directive 1999/5/EC [i.3] of the European Parliament
and of the Council of 9 March 1999 on radio equipment and telecommunications terminal equipment and the mutual
recognition of their conformity ("the R&TTE Directive").
The present document is intended to cover the provisions of article 3.2 of Directive 1999/5/EC
(R&TTE Directive) [i.3].
The present document does not apply to radio equipment for which a specific Harmonized EN applies as such
Harmonized EN may specify additional EN requirements relevant to the presumption of conformity under article 3.2 of
the R&TTE Directive.
Technical specifications relevant to Directive 1999/5/EC [i.3] are given in annex A.
Proposed national transposition dates
Date of latest announcement of this EN (doa): 3 months after ETSI publication
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 6 months after doa
Date of withdrawal of any conflicting National Standard (dow): 18 months after doa
ETSI
---------------------- Page: 6 ----------------------
7 Draft ETSI EN 302 065 V1.2.1 (2009-12)
Introduction
The present document is part of a set of standards developed by ETSI and is designed to fit in a modular structure to
cover all radio and telecommunications terminal equipment within the scope of the R&TTE Directive. The modular
structure is shown in EG 201 399 [i.1].
UWB Technologies
The present document provides a generic set of technical requirements covering many different types of UWB
technologies used for short range communications. These technologies can be broken down into two groups:
1) Impulse based technologies; and
2) RF carrier based technologies.
The following clauses give a brief overview of these UWB technologies and their associated modulation techniques.
Impulse technology
Impulse derived UWB technology consists of a series of impulses created from a dc voltage step whose rise time can be
modified to provide the maximum useful number of spectral emission frequencies. This derived impulse can then be
suitably modified by the use of filters to locate the resulting waveform within a specific frequency spectrum range. This
filter can be a stand alone filter or incorporated into an antenna design to reduce emissions outside the designated
frequency spectrum.
Modulation techniques include pulse positioning in time, pulse suppression and other techniques to convey information.
The transmitted energy is summed at the receiver to reproduce the transmitted pulse.
This technology is suitable for direct and non-direct line of sight communications, any reflected or time delayed
emissions being suppressed by the receiver input circuits.
RF carrier based technology
RF carrier based UWB technology is based upon classical radio carrier technology suitably modulated by a baseband
modulating process. The modulating process must produce a bandwidth in excess of 50 MHz to be defined as UWB.
Different modulating processes are used to transmit the data information to the receiver and can consist of a series of
single hopping frequencies or multi-tone carriers.
This technology can be used for both direct and non-direct line of sight communications, any reflected or time delayed
emissions being suppressed by the receiver input circuits.
Test and measurement limitations
The ERA report 2006-0713 [i.9] has shown that there are practical limitations on measurements of RF radiated
emissions. The minimum radiated levels that can be practically measured in the lower GHz frequency range by using a
radiated measurement setup with a horn antenna and pre-
...
SLOVENSKI STANDARD
oSIST prEN 302 065 V1.2.1:2010
01-marec-2010
(OHNWURPDJQHWQD]GUXåOMLYRVWLQ]DGHYHY]YH]L]UDGLMVNLPVSHNWURP (50
1DSUDYHNUDWNHJDGRVHJD 65' NLXSRUDEOMDMRXOWUDãLURNRSDVRYQR 8:%
WHKQRORJLMR]DQDPHQHNRPXQLFLUDQMD+DUPRQL]LUDQL(1NL]DMHPDELVWYHQH
]DKWHYHþOHQDGLUHNWLYH5 77(
Electromagnetic compatibility and Radio spectrum Matters (ERM) - Short Range Devices
(SRD) using Ultra Wide Band technology (UWB) for communications purposes -
Harmonized EN covering essential requirements of article 3.2 of the R&TTE Directive
Ta slovenski standard je istoveten z: EN 302 065 Version 1.2.1
ICS:
33.060.99 Druga oprema za radijske Other equipment for
komunikacije radiocommunications
33.100.01 Elektromagnetna združljivost Electromagnetic compatibility
na splošno in general
oSIST prEN 302 065 V1.2.1:2010 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN 302 065 V1.2.1:2010
---------------------- Page: 2 ----------------------
oSIST prEN 302 065 V1.2.1:2010
Draft ETSI EN 302 065 V1.2.1 (2009-12)
Harmonized European Standard (Telecommunications series)
Electromagnetic compatibility and
Radio spectrum Matters (ERM);
Short Range Devices (SRD) using
Ultra Wide Band technology (UWB)
for communications purposes;
Harmonized EN covering essential requirements
of article 3.2 of the R&TTE Directive
---------------------- Page: 3 ----------------------
oSIST prEN 302 065 V1.2.1:2010
2 Draft ETSI EN 302 065 V1.2.1 (2009-12)
Reference
REN/ERM-TGUWB-0118-1
Keywords
radio, SRD, testing, UWB
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
Individual copies of the present document can be downloaded from:
http://www.etsi.org
The present document may be made available in more than one electronic version or in print. In any case of existing or
perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF).
In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive
within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
http://portal.etsi.org/chaircor/ETSI_support.asp
Copyright Notification
No part may be reproduced except as authorized by written permission.
The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2009.
All rights reserved.
TM TM TM TM
DECT , PLUGTESTS , UMTS , TIPHON , the TIPHON logo and the ETSI logo are Trade Marks of ETSI registered
for the benefit of its Members.
TM
3GPP is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners.
LTE™ is a Trade Mark of ETSI currently being registered
for the benefit of its Members and of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI
---------------------- Page: 4 ----------------------
oSIST prEN 302 065 V1.2.1:2010
3 Draft ETSI EN 302 065 V1.2.1 (2009-12)
Contents
Intellectual Property Rights . 6
Foreword . 6
Introduction . 7
1 Scope . 9
2 References . 9
2.1 Normative references . 10
2.2 Informative references . 10
3 Definitions, symbols and abbreviations . 11
3.1 Definitions . 11
3.2 Symbols . 12
3.3 Abbreviations . 12
4 Technical requirements specification . 13
4.1 Technical requirements . 13
4.1.1 Operating bandwidth. 13
4.1.1.1 Definition . 13
4.1.1.2 Test procedure . 13
4.1.1.3 Limit . 13
4.1.1.4 Measurement uncertainty . 14
4.1.2 Maximum value of mean power spectral density . 14
4.1.2.1 Definition . 14
4.1.2.2 Test procedure . 14
4.1.2.3 Limit . 14
4.1.2.4 Maximum allowable measurement uncertainty. 15
4.1.3 Maximum value of peak power . 15
4.1.3.1 Definition . 15
4.1.3.2 Test procedure . 15
4.1.3.3 Limit . 15
4.1.3.4 Maximum allowable measurement uncertainty. 16
4.1.4 Transmit Power Control . 16
4.1.4.1 Definition . 16
4.1.4.2 Test procedure . 16
4.1.4.3 Limit . 17
4.1.4.4 Maximum allowable measurement uncertainty. 17
4.1.5 Receiver spurious emissions . 17
4.1.5.1 Definition . 17
4.1.5.2 Test procedure . 17
4.1.5.3 Limit . 17
4.1.5.4 Maximum allowable measurement uncertainty. 18
4.1.6 Detect-And-Avoid (DAA) . 18
4.1.6.1 Introduction . 18
4.1.6.1.1 Applicable frequency ranges . 18
4.1.6.1.2 DAA operational modes . 18
4.1.6.2 Test procedure . 19
4.1.6.3 Limit . 19
4.1.6.4 Maximum allowable measurement uncertainty. 19
4.1.7 Low Duty Cycle (LDC) . 19
4.1.7.1 Definitions . 19
4.1.7.2 Test procedure . 19
4.1.7.3 Limits . 19
4.1.8 Equivalent mitigation techniques . 20
5 Essential radio test suites . 20
5.1 Product information . 20
5.2 Requirements for the test modulation . 21
ETSI
---------------------- Page: 5 ----------------------
oSIST prEN 302 065 V1.2.1:2010
4 Draft ETSI EN 302 065 V1.2.1 (2009-12)
5.3 Test conditions, power supply and ambient temperatures . 21
5.3.1 Test conditions . 21
5.3.2 Power sources . 21
5.3.2.1 Power sources for stand-alone equipment . 21
5.3.2.2 Power sources for plug-in radio devices . 21
5.3.3 Normal test conditions . 22
5.3.3.1 Normal temperature and humidity . 22
5.3.3.2 Normal power source . 22
5.3.3.2.1 Mains voltage . 22
5.3.3.2.2 Lead-acid battery power sources used on vehicles . 22
5.3.3.2.3 Other power sources . 22
5.4 Choice of equipment for test suites . 22
5.4.1 Choice of model . 22
5.4.2 Presentation. 22
5.4.3 Operating bandwidth. 22
5.4.4 Test sites and general arrangements for radiated measurements . 23
5.5 Testing of host connected equipment and plug-in radio devices . 23
5.5.1 The use of a host or test fixture for testing plug-In radio devices . 23
5.5.2 Testing of combinations . 23
5.5.2.1 Alternative A: General approach for combinations . 23
5.5.2.2 Alternative B: For host equipment with a plug-in radio device . 23
5.5.2.3 Alternative C: For combined equipment with a plug-in radio device . 24
5.6 Interpretation of the measurement results . 24
5.6.1 Measurement uncertainty is equal to or less than maximum acceptable uncertainty . 24
5.6.2 Measurement uncertainty is greater than maximum acceptable uncertainty . 25
5.7 Other emissions . 25
5.8 Test procedures for essential radio test suites. 25
5.8.1 General . 25
5.8.2 Maximum mean power spectral density . 25
5.8.3 Maximum peak power . 27
5.8.4 Operating bandwidth. 27
5.8.5 Receiver spurious emissions . 28
5.8.6 Low Duty Cycle . 28
5.8.7 Test Procedure for the radiolocation systems DAA test . 28
5.8.7.1 Introduction . 28
5.8.7.2 Start-up test . 30
5.8.7.2.1 Test without a radiolocation test signal during the Minimum Initial Channel Availability
Check Time, T . 30
avail_time_min
5.8.7.2.2 Tests with a radiolocation test signal at the beginning of the Minimum Initial Channel
Availability Check Time, T . 31
avail_time_min
5.8.7.2.3 Tests with radiolocation test signal at the end of the Minimum Initial Channel Availability
Check Time, T . 33
avail_time_min
5.8.7.3 In-operation test . 35
5.8.7.3.1 In-operation test procedure . 35
5.8.7.4 Test patterns for the radiolocation DAA test . 36
5.8.8 Test Procedure for BWA systems in the band 3,4 GHz to 3,8 GHz . 37
5.8.8.1 Introduction . 37
5.8.8.1.1 UWB radio devices with and without victim service identification . 37
5.8.8.2 Initial start-up test . 37
5.8.8.2.1 Test without a BWA test signal during the Minimum Initial Channel Availability Check
Time, T . 38
avail_time_min
5.8.8.2.2 Tests with a BWA test signal at the beginning of the Minimum Initial Channel Availability
Check Time, T . 38
avail_time
5.8.8.2.3 Tests with a BWA test signal at the end of the Minimum Initial Channel Availability Check
Time, T . 40
avail_time
5.8.8.3 In-operation test . 41
5.8.8.4 Test Patterns for BWA Testing . 42
Annex A (normative): HS Requirements and conformance Test specifications Table (HS-
RTT) . 44
Annex B (normative): Radiated measurements . 47
ETSI
---------------------- Page: 6 ----------------------
oSIST prEN 302 065 V1.2.1:2010
5 Draft ETSI EN 302 065 V1.2.1 (2009-12)
B.1 Test sites and general arrangements for measurements involving the use of radiated fields . 47
B.1.1 Anechoic chamber . 47
B.1.2 Anechoic chamber with a conductive ground plane . 48
B.1.3 Test antenna . 50
B.1.4 Substitution antenna . 50
B.1.5 Measuring antenna . 50
B.2 Guidance on the use of a radiation test site . 50
B.2.1 Verification of the test site . 50
B.2.2 Preparation of the EUT . 51
B.2.3 Power supplies to the EUT . 51
B.2.4 Range length . 51
B.2.5 Site preparation . 52
B.3 Coupling of signals . 52
B.3.1 General . 52
B.3.2 Data Signals. 52
B.4 Standard test methods . 52
B.4.1 Calibrated setup . 52
B.4.2 Substitution method . 53
B.5 Standard calibration method . 54
Annex C (normative): Conducted measurements for DAA testing . 56
Annex D (informative): Measurement antenna and preamplifier specifications . 57
Annex E (normative): Radiolocation services in the band 3,1 GHz to 3,4 GHz . 58
Annex F (normative): Broadband wireless access services in the band 3,4 GHz to 3,8 GHz . 59
Annex G (normative): Radiolocation services in the band 8,5 GHz to 9,0 GHz . 60
Annex H (informative): Calculation of peak limit for 3 MHz measurement bandwidth . 61
Annex I (normative): ICS Proforma for DAA radio device . 63
I.1 Identification of the protocol . 63
I.2 ICS proforma tables. 63
I.2.1 Avoidance Modes . 63
Annex J (informative): Bibliography . 64
Annex K (informative): The EN title in the official languages . 65
History . 66
ETSI
---------------------- Page: 7 ----------------------
oSIST prEN 302 065 V1.2.1:2010
6 Draft ETSI EN 302 065 V1.2.1 (2009-12)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (http://webapp.etsi.org/IPR/home.asp).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This Harmonized European Standard (Telecommunications series) has been produced by ETSI Technical Committee
Electromagnetic compatibility and Radio spectrum Matters (ERM), and is now submitted for the Public Enquiry phase
of the ETSI standards Two-step Approval Procedure.
The present document has been produced by ETSI in response to a mandate from the European Commission issued
under Council Directive 98/34/EC [i.2] (as amended) laying down a procedure for the provision of information in the
field of technical standards and regulations.
The present document is intended to become a Harmonized Standard, the reference of which will be published in the
Official Journal of the European Communities referencing the Directive 1999/5/EC [i.3] of the European Parliament
and of the Council of 9 March 1999 on radio equipment and telecommunications terminal equipment and the mutual
recognition of their conformity ("the R&TTE Directive").
The present document is intended to cover the provisions of article 3.2 of Directive 1999/5/EC
(R&TTE Directive) [i.3].
The present document does not apply to radio equipment for which a specific Harmonized EN applies as such
Harmonized EN may specify additional EN requirements relevant to the presumption of conformity under article 3.2 of
the R&TTE Directive.
Technical specifications relevant to Directive 1999/5/EC [i.3] are given in annex A.
Proposed national transposition dates
Date of latest announcement of this EN (doa): 3 months after ETSI publication
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 6 months after doa
Date of withdrawal of any conflicting National Standard (dow): 18 months after doa
ETSI
---------------------- Page: 8 ----------------------
oSIST prEN 302 065 V1.2.1:2010
7 Draft ETSI EN 302 065 V1.2.1 (2009-12)
Introduction
The present document is part of a set of standards developed by ETSI and is designed to fit in a modular structure to
cover all radio and telecommunications terminal equipment within the scope of the R&TTE Directive. The modular
structure is shown in EG 201 399 [i.1].
UWB Technologies
The present document provides a generic set of technical requirements covering many different types of UWB
technologies used for short range communications. These technologies can be broken down into two groups:
1) Impulse based technologies; and
2) RF carrier based technologies.
The following clauses give a brief overview of these UWB technologies and their associated modulation techniques.
Impulse technology
Impulse derived UWB technology consists of a series of impulses created from a dc voltage step whose rise time can be
modified to provide the maximum useful number of spectral emission frequencies. This derived impulse can then be
suitably modified by the use of filters to locate the resulting waveform within a specific frequency spectrum range. This
filter can be a stand alone filter or incorporated into an antenna design to reduce emissions outside the de
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.