ETSI EN 302 217-3 V1.1.3 (2005-03)
Fixed Radio Systems; Characteristics and requirements for point-to-point equipment and antennas; Part 3: Harmonized EN covering essential requirements of Article 3.2 of R&TTE Directive for equipment operating in frequency bands where no frequency co-ordination is applied
Fixed Radio Systems; Characteristics and requirements for point-to-point equipment and antennas; Part 3: Harmonized EN covering essential requirements of Article 3.2 of R&TTE Directive for equipment operating in frequency bands where no frequency co-ordination is applied
DEN/TM-04131-3
Fiksni radijski sistemi – Karakteristike in zahteve za opremo tipa točka-točka in antene – 3. del: Harmonizirani EN, ki zajema bistvene zahteve člena 3.2 direktive R&TTE za opremo, ki deluje v frekvenčnih pasovih, kjer se ne izvaja frekvenčna koordinacija
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.NRRUGLQDFLMDFixed Radio Systems; Characteristics and requirements for point-to-point equipment and antennas; Part 3: Harmonized EN covering essential requirements of Article 3.2 of R&TTE Directive for equipment operating in frequency bands where no frequency co-ordination is applied33.120.40AnteneAerials33.060.30Radiorelejni in fiksni satelitski komunikacijski sistemiRadio relay and fixed satellite communications systemsICS:Ta slovenski standard je istoveten z:EN 302 217-3 Version 1.1.3SIST EN 302 217-3 V1.1.3:2005en01-junij-2005SIST EN 302 217-3 V1.1.3:2005SLOVENSKI
STANDARD
SIST EN 302 217-3 V1.1.3:2005
ETSI EN 302 217-3 V1.1.3 (2005-03)Candidate Harmonized European Standard (Telecommunications series) Fixed Radio Systems;Characteristics and requirements forpoint-to-point equipment and antennas;Part 3: Harmonized EN covering essential requirementsof Article 3.2 of R&TTE Directive for equipment operating infrequency bands where no frequency co-ordination is applied
SIST EN 302 217-3 V1.1.3:2005
ETSI ETSI EN 302 217-3 V1.1.3 (2005-03) 2
Reference DEN/TM-04131-3 Keywords DFRS, digital, DRRS, FWA, point-to-point, radio, regulation, transmission ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00
Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C Association à but non lucratif enregistrée à la Sous-Préfecture de Grasse (06) N° 7803/88
Important notice Individual copies of the present document can be downloaded from: http://www.etsi.org The present document may be made available in more than one electronic version or in print. In any case of existing or perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF). In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at http://portal.etsi.org/tb/status/status.asp If you find errors in the present document, please send your comment to one of the following services: http://portal.etsi.org/chaircor/ETSI_support.asp Copyright Notification No part may be reproduced except as authorized by written permission. The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2005. All rights reserved.
DECTTM, PLUGTESTSTM and UMTSTM are Trade Marks of ETSI registered for the benefit of its Members. TIPHONTM and the TIPHON logo are Trade Marks currently being registered by ETSI for the benefit of its Members. 3GPPTM is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. SIST EN 302 217-3 V1.1.3:2005
ETSI ETSI EN 302 217-3 V1.1.3 (2005-03) 3
Contents Intellectual Property Rights.5 Foreword.5 Introduction.6 1 Scope.8 2 References.9 3 Definitions, symbols and abbreviations.10 3.1 Definitions.10 3.2 Symbols.10 3.3 Abbreviations.10 4 Technical requirements specifications.10 4.1 Environmental profile.10 4.2 RF-channel Selection.10 4.2.1 RF-channel selection procedure.11 4.2.2 Interference avoidance requirements.11 4.2.2.1 Interference avoidance limit.11 4.2.3 Frequency agile automatic channel selection.11 4.3 Transmitter requirements.11 4.3.1 Transmitter power.12 4.3.1.1 Transmitter power.12 4.3.1.2 Equivalent Isotropically Radiated Power (EIRP).12 4.3.1.3 Output Power Tolerance.12 4.3.2 Radio Frequency (RF) spectrum mask.12 4.3.3 Spurious emissions - external.12 4.3.4 Radio frequency tolerance.13 4.3.5 Antenna directional requirements.13 4.3.5.1 Radiation Pattern Envelope (Off-axis EIRP density).13 4.3.5.2 Antenna gain.13 4.3.5.3 Antenna Cross-Polar Discrimination (XPD).13 4.4 Receiver requirements.13 4.4.1 Spurious emissions.13 5 Testing for compliance with technical requirements.14 5.1 Environmental conditions for testing.14 5.2 RF-channel selection.14 5.3 Essential radio test suites for the transmitter.15 5.3.1 Transmitter power.15 5.3.1.1 Transmitter power.15 5.3.1.2 Equivalent Isotropically Radiated Power (EIRP).16 5.3.1.3 Output power tolerance.16 5.3.2 RF spectrum mask.16 5.3.3 Spurious emissions - external.16 5.3.4 Radio frequency tolerance.16 5.3.5 Antenna and system directional requirements.16 5.3.5.1 Radiation pattern envelope (Off-axis EIRP density).17 5.3.5.2 Antenna gain.17 5.3.5.3 Antenna Cross-Polar Discrimination (XPD).17 5.4 Essential radio test suites for the receiver.17 5.4.1 Spurious emissions - external.17 Annex UA (normative): Frequency bands around 58 GHz.18 UA.0 Introduction.18 UA.1 System UA.1 digital.18 UA.1.1 Frequency bands and channel arrangements.18 SIST EN 302 217-3 V1.1.3:2005
ETSI ETSI EN 302 217-3 V1.1.3 (2005-03) 4
UA.1.1.1 Frequency band.18 UA.1.1.2 Radio channel arrangements.18 UA.1.1.3 Transmission capacity.18 UA.1.2 Transmitter.18 UA.1.2.1 Transmitter power.18 UA.1.2.2 Equivalent Isotropically Radiated Power (EIRP).19 UA.1.2.3 Output power tolerance.19 UA.1.2.4 RF spectrum masks.19 UA.1.2.4.1 Limits.19 UA.1.2.4.2 Spectrum analyser settings.20 UA.1.2.5 Spurious emissions-external.20 UA.1.2.6 Radio frequency tolerance.20 UA.1.2.7 RF-channel selection parameters.20 UA.1.3 Receiver.20 UA.2 System UA.2 analogue.21 UA.2.1 Frequency bands and channel arrangements.21 UA.2.1.1 Frequency band.21 UA.2.1.2 Radio channel arrangements.21 UA.2.1.3 Transmission capacity.21 UA.2.2 Transmitter.21 UA.2.2.1 Transmitter power.21 UA.2.2.2 Equivalent Isotropically Radiated Power (EIRP).21 UA.2.2.3 Output power tolerance.21 UA.2.2.4 RF spectrum masks.21 UA.2.2.5 Spurious emissions - external.21 UA.2.2.6 RF frequency tolerance.21 UA.2.3 Receiver requirements.22 UA.2.3.1 Spurious emissions.22 Annex UB (normative): The EN Requirements Table (EN-RT).23 Annex UC (normative): Wide radio-frequency band covering units and multirate equipment specification and tests.25 UC.1 Wide radio-frequency band covering units.25 UC.2 Multirate/multiformat equipment.27 Annex UD (informative): Rationale for the interference limit formula.28 UD.1 Analysis of the quality value for the channel selection procedure.28 UD.1.1 Error-performance and availability requirements for Class A equipment.28 UD.1.1.1 Example in the 58 GHz band:.28 UD.1.2 Theoretical background.28 UD.1.3 Typical co-channel interference situation when channel rejection threshold is used.29 UD.2 Protection capability of the RF-channel selection procedure.30 UD.3 Frequency agility criteria.31 Annex UE (informative): Basic parameters of CEPT/ERC/Recommendation 12-09.32 Annex UF (informative): Bibliography.33 Annex UG (informative): The EN title in the official languages.34 History.35
SIST EN 302 217-3 V1.1.3:2005
ETSI ETSI EN 302 217-3 V1.1.3 (2005-03) 5
Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (http://webapp.etsi.org/IPR/home.asp). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This Candidate Harmonized European Standard (Telecommunications series) has been produced by ETSI Technical Committee Transmission and Multiplexing (TM). The present document has been produced by ETSI in response to a mandate from the European Commission issued under Council Directive 98/34/EC laying down a procedure for the provision of information in the field of technical standards and regulations. The present document is intended to become a Harmonized Standard, the reference of which will be published in the Official Journal of the European Communities referencing the Directive 1999/5/EC [1] of the European Parliament and of the Council of 9 March 1999 on radio equipment and telecommunications terminal equipment and the mutual recognition of their conformity ("R&TTE Directive"). The present document is part 3 of a multipart deliverable covering Fixed Radio Systems Characteristics and requirements for point-to-point equipment and antennas, as identified below: Part 1: "Overview and system-independent common characteristics"; Part 2-1: "System-dependent requirements for digital systems operating in frequency bands where frequency co-ordination is applied"; Part 2-2 "Harmonized EN covering essential requirements of Article 3.2 of R&TTE Directive for digital systems operating in frequency bands where frequency co-ordination is applied"; Part 3: "Harmonized EN covering essential requirements of Article 3.2 of R&TTE Directive for equipment operating in frequency bands where no frequency co-ordination is applied"; Part 4-1: "System-dependent requirements for antennas"; Part 4-2: "Harmonized EN covering essential requirements of Article 3.2 of R&TTE Directive for antennas". The present document together with EN 302 217-2-2 (see bibliography) and EN 302 217-4-2 [8] intend to replace and supersede the harmonized EN 301 751 (see bibliography) for all P-P equipment and antennas.
National transposition dates Date of adoption of this EN: 25 February 2005 Date of latest announcement of this EN (doa): 31 May 2005 Date of latest publication of new National Standard or endorsement of this EN (dop/e):
30 November 2005 Date of withdrawal of any conflicting National Standard (dow): 31 May 2007
SIST EN 302 217-3 V1.1.3:2005
ETSI ETSI EN 302 217-3 V1.1.3 (2005-03) 6
Introduction The present document is part of a set of standards designed to fit in a modular structure to cover all radio and telecommunications terminal equipment under the R&TTE Directive. Each standard is a module in the structure. The modular structure is shown in figure 1.
New standards for human exposure to Electromagnetic Fields and, if needed, new standards for acoustic safety Use of spectrum * If needed Scoped by
equipment
class or type Scoped by frequency and/or equipment type Disability* Privacy* Fraud* No harm to the network* Emergency* Interworking via
the network* Interworking with the network Non-radio Radio (RE) Non-TTE TTE 3.1b 3.2 3.3c 3.3b 3.3a 3.3d 3.3e 3.3f Radio Product EMC EN 301 489-1 and EN 301 489-4 Generic and product standards also notified under EMC Directive Standards also notified under LV Directive 3.1a New radio harmonized standards Spectrum EMC Safety Scope of this EN: any point-to-point FDRS and antennas in all frequency bands
Figure 1: Modular structure for the various standards used under the R&TTE Directive SIST EN 302 217-3 V1.1.3:2005
ETSI ETSI EN 302 217-3 V1.1.3 (2005-03) 7
The left hand edge of figure 1 shows the different clauses of article 3 of the R&TTE Directive [1]. For article 3.3 various horizontal boxes are shown. Dotted lines indicate that at the time of publication of the present document essential requirements in these areas have to be adopted by the Commission. Whenever such essential requirements are adopted and as far and as long as they are applicable, they will justify individual standards whose scope is likely to be specified by function or interface type. The vertical boxes show the standards under article 3.2 for the use of the radio spectrum by radio equipment. The scopes of these standards are specified either by frequency (normally in the case where frequency bands are harmonized) or by radio equipment type. For article 3.1b the diagram shows EN 301 489 (see bibliography), the multi-part product EMC standard for radio used under the EMC Directive 89/336/EEC (see bibliography). NOTE: For Fixed Radio Systems EN, EN 301 489-1 (see bibliography) and EN 301 489-4 (see bibliography) are relevant. For article 3.1a the diagram shows the existing safety standards currently used under the LV Directive 73/23/EEC (see bibliography) and new standards covering human exposure to electromagnetic fields. New standards covering acoustic safety may also be required. The bottom of the figure 1 shows the relationship of the standards to radio equipment and telecommunications terminal equipment. Equipment may be radio equipment, telecommunications terminal equipment or both. A radio spectrum standard will apply if it is radio equipment. An article 3.3 standard will apply as well only if the relevant essential requirement under the R&TTE Directive [1] is adopted by the Commission and if the equipment in question is covered by the scope of the corresponding standard. Thus, depending on the nature of the equipment, the essential requirements under the R&TTE Directive [1] may be covered in a set of standards. The modularity principle has been taken because: • It minimizes the number of standards needed. Because equipment may, in fact, have multiple interfaces and functions it is not practicable to produce a single standard for each possible combination of functions that may occur in equipment. • It provides scope for standards to be added: - under article 3.2 when new frequency bands are agreed; or - under article 3.3 should the Commission take the necessary decisions without requiring alteration of standards that are already published. • It clarifies, simplifies and promotes the usage of Harmonized Standards as the relevant means of conformity assessment. SIST EN 302 217-3 V1.1.3:2005
ETSI ETSI EN 302 217-3 V1.1.3 (2005-03) 8
1 Scope The present document specifies the essential requirements for Digital Fixed Radio Systems (DFRS) operating in frequency bands, which do not require co-ordinated frequency planning. It is intended to cover the provisions of Directive 1999/5/EC [1] (R&TTE Directive) regarding article 3.2, which states that "… radio equipment shall be so constructed that it effectively uses the spectrum allocated to terrestrial/space radio communications and orbital resources so as to avoid harmful interference". The present document with EN 302 217-2-2 (see bibliography) and EN 302 217-4-2 [8] will replace and supersede, after a suitable transition period, the harmonized EN 301 751 (see bibliography) for all P-P equipment and antennas. Those parts of this multipart EN introduces, for systems (equipment and antennas) already covered by EN 301 751 (see bibliography), equal, technically equivalent or less stringent requirements. Therefore, from a strictly technical point of view, it is expected that equipment already conforming to the previous EN 301 751 (see bibliography), would not need a new test report for re-assessment of essential requirements according this new multipart EN; however, legal implications with respect to the declaration of conformity and equipment labelling are not in the scope of the present document. In addition to the present document, other ENs that specify technical requirements in respect of essential requirements under other parts of article 3 of the R&TTE Directive [1] will apply to equipment within the scope of the present document. NOTE: A list of such ENs is included on the web site http://www.newapproach.org. In order to technically cover different market and network requirements, with an appropriate balance of performance to cost and effective and appropriate use of the radio spectrum, the present document, together with EN 302 217-4-2 [8], offers system types and antennas alternatives, for selection by administrations, operators and manufacturers dependent on the desired use of the radio spectrum and network/market requirements, those options include: • channel separation alternatives (as provided by the relevant CEPT Recommendation); • implemented procedure for free radio channel selection; • antenna directivity class alternatives (for different network density requirement). The present document is mainly intended to cover fixed radio equipment without integral antennas. However, it also applies to fixed radio systems products with integral antennas, for which all the technical requirements included in the present document and in EN 302 217-4-2 [8] apply. For more background information on the equipment and antenna parameters here identified as relevant to article 3.2 of R&TTE Directive see EG 201 399 (see bibliography) and TR 101 506 (see bibliography). For example, the frequency band 58 GHz is proposed to be used by various technologies for uncoordinated use of the band. Besides the RF-channel selection procedure, specified in clause 4.2 to avoid unacceptable interference situations, this band also benefits from the high and stable atmospheric attenuation which suppresses efficiently distant interferers (about 10 to 15 dB/km at sea level, refer to ITU-R Recommendation P.676 (see bibliography). For the purposes of the present document two equipment Classes are specified depending on the network requirements: • Class A: Digital equipment for High Density Fixed Service (HDFS) applications typically connected to public networks, which apply the RF-channel selection procedure (see clause 4.2), error performance and availability requirements (see EN 302 217-1 [7]). • Class B: Equipment without network requirements for quality of service, typically private connections. Typical applications for Class A equipment are interconnection between cellular networks where, in some cases, there is a need for short length connections (up to about 500 m). The RF channel selection procedure shall be used to protect existing systems from a new system being commissioned. However, the channel selection procedure may not guarantee interference free installation or operation in all cases, due to limitations in the procedure with respect to the variety of systems. Typical applications for Class B equipment are in private connections, such as video surveillance systems. SIST EN 302 217-3 V1.1.3:2005
ETSI ETSI EN 302 217-3 V1.1.3 (2005-03) 9
2 References The following documents contain provisions which, through reference in this text, constitute provisions of the present document. • References are either specific (identified by date of publication and/or edition number or version number) or non-specific. • For a specific reference, subsequent revisions do not apply. • For a non-specific reference, the latest version applies. Referenced documents which are not found to be publicly available in the expected location might be found at http://docbox.etsi.org/Reference. NOTE: With regard to ETSI ENs, the third digit of the version number is not considered essential for dated reference purposes because the ETSI Technical Working Procedures reserve this digit for editorially changed versions, thereby not affecting the technical parameters
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.