IEC 62386-210:2011

Digital addressable lighting interface - Part 210: Particular requirements for control gear - Sequencer (device type 9)

IEC 62386-210:2011 specifies a protocol and test procedures for the control by digital signals of electronic control gear working as automatic sequencers.
This publication is to be read in conjunction with IEC 62386-101:2009 and IEC 62386-102:2009.

Interface d'éclairage adressable numérique - Partie 210: Exigences particulières pour les appareillages de commande - Séquenceur (dispositifs de type 9)

La CEI 62386-210:2011 spécifie un protocole et des procédures d'essai applicables aux appareillages électroniques commandés par des signaux numériques fonctionnant comme des séquenceurs automatiques.
Cette publication doit être lue conjointement avec la CEI 62386-101:2009 et la CEI 62386-102:2009.

General Information

• Status: Withdrawn
• Publication Date: 19-Apr-2011
• Withdrawal Date: 30-Jun-2014
• ICS: 29.140.50 - Lighting installation systems
• ICS: 29.140.99 - Other standards related to lamps
• Technical Committee: SC 34C - Auxiliaries for lamps
• Drafting Committee: PT 62386 - TC 34/SC 34C/PT 62386
• Current Stage: WPUB - Publication withdrawn
• Completion Date: 04-Apr-2014

Standards Content (Sample)

IEC 62386-210 ®
Edition 1.0 2011-04
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Digital addressable lighting interface –
Part 210: Particular requirements for control gear – Sequencer (device type 9)

Interface d’éclairage adressable numérique –
Partie 210: Exigences particulières pour les appareillages de commande –
Séquenceur (dispositifs de type 9)

All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by
any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either IEC or
IEC's member National Committee in the country of the requester.
If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication,
please contact the address below or your local IEC member National Committee for further information.

Droits de reproduction réservés. Sauf indication contraire, aucune partie de cette publication ne peut être reproduite
ni utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie
et les microfilms, sans l'accord écrit de la CEI ou du Comité national de la CEI du pays du demandeur.
Si vous avez des questions sur le copyright de la CEI ou si vous désirez obtenir des droits supplémentaires sur cette
publication, utilisez les coordonnées ci-après ou contactez le Comité national de la CEI de votre pays de résidence.

IEC Central Office
3, rue de Varembé
CH-1211 Geneva 20
Switzerland
Email: [e-mail]
Web: www.iec.ch
About the IEC
The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes
International Standards for all electrical, electronic and related technologies.

About IEC publications
The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the
latest edition, a corrigenda or an amendment might have been published.
 Catalogue of IEC publications: www.iec.ch/searchpub
The IEC on-line Catalogue enables you to search by a variety of criteria (reference number, text, technical committee,…).
It also gives information on projects, withdrawn and replaced publications.
 IEC Just Published: www.iec.ch/online_news/justpub
Stay up to date on all new IEC publications. Just Published details twice a month all new publications released. Available
on-line and also by email.
 Electropedia: www.electropedia.org
The world's leading online dictionary of electronic and electrical terms containing more than 20 000 terms and definitions
in English and French, with equivalent terms in additional languages. Also known as the International Electrotechnical
Vocabulary online.
 Customer Service Centre: www.iec.ch/webstore/custserv
If you wish to give us your feedback on this publication or need further assistance, please visit the Customer Service
Centre FAQ or contact us:
Email: [e-mail]
Tel.: [phone]
Fax: [phone]
A propos de la CEI
La Commission Electrotechnique Internationale (CEI) est la première organisation mondiale qui élabore et publie des
normes internationales pour tout ce qui a trait à l'électricité, à l'électronique et aux technologies apparentées.

A propos des publications CEI
Le contenu technique des publications de la CEI est constamment revu. Veuillez vous assurer que vous possédez
l’édition la plus récente, un corrigendum ou amendement peut avoir été publié.
 Catalogue des publications de la CEI: www.iec.ch/searchpub/cur_fut-f.htm
Le Catalogue en-ligne de la CEI vous permet d’effectuer des recherches en utilisant différents critères (numéro de référence,
texte, comité d’études,…). Il donne aussi des informations sur les projets et les publications retirées ou remplacées.
 Just Published CEI: www.iec.ch/online_news/justpub
Restez informé sur les nouvelles publications de la CEI. Just Published détaille deux fois par mois les nouvelles
publications parues. Disponible en-ligne et aussi par email.
 Electropedia: www.electropedia.org
Le premier dictionnaire en ligne au monde de termes électroniques et électriques. Il contient plus de 20 000 termes et
définitions en anglais et en français, ainsi que les termes équivalents dans les langues additionnelles. Egalement appelé
Vocabulaire Electrotechnique International en ligne.
 Service Clients: www.iec.ch/webstore/custserv/custserv_entry-f.htm
Si vous désirez nous donner des commentaires sur cette publication ou si vous avez des questions, visitez le FAQ du
Service clients ou contactez-nous:
Email: [e-mail]
Tél.: [phone]
Fax: [phone]
IEC 62386-210 ®
Edition 1.0 2011-04
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Digital addressable lighting interface –
Part 210: Particular requirements for control gear – Sequencer (device type 9)

Interface d’éclairage adressable numérique –
Partie 210: Exigences particulières pour les appareillages de commande –
Séquenceur (dispositifs de type 9)

INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
PRICE CODE
INTERNATIONALE
CODE PRIX XB
ICS 29.140.50; 29.140.99 ISBN 978-2-88912-467-1

– 2 – 62386-210 © IEC:2011
CONTENTS
FOREWORD . 5
INTRODUCTION . 7
1 Scope . 8
2 Normative references . 8
3 Terms and definitions . 8
4 General description . 9
5 Electrical specifications . 9
6 Interface power supply . 9
7 Transmission protocol structure . 9
8 Timing . 9
9 Method of operation . 9
10 Declaration of variables . 14
11 Definition of commands . 15
12 Test procedures . 24
Bibliography . 62

Figure 1 – Timing example for an automatic sequence . 13
Figure 2 – Application extended configuration command sequence example . 16
Figure 3 – Test sequence "Physical address allocation" . 24
Figure 4 – Test sequence "QUERY FEATURES" . 25
Figure 5 – Test sequence "Configure POINT N" . 26
Figure 6 – Test sequence "Configuration – sent twice" . 27
Figure 7 – Test sequence "Configuration – time-out" . 28
Figure 8 – Test sequence "Configuration – command in-between 1" . 29
Figure 9 – Test sequence "Configuration – command in-between 2" . 30
Figure 10 – Test sequence "COPY TO POINT N" . 31
Figure 11 – Test sequence "COPY TO POINT N – sent twice" . 32
Figure 12 – Test sequence "COPY TO POINT N – time-out" . 33
Figure 13 – Test sequence "COPY TO POINT N – command in-between" . 34
Figure 14 – Test sequence "CHANNEL SELECTION" . 35
Figure 15 – Test sequence "CHANNEL SELECTION – sent twice / time-out" . 36
Figure 16 – Test sequence "CHANNEL SELECTION – command in-between" . 37
Figure 17 – Test sequence "CONFIGURE CONTROL N" . 38
Figure 18 – Test sequence "CONFIGURE CONTROL N – sent twice / time-out" . 39
Figure 19 – Test sequence "CONFIGURE CONTROL N – command in-between" . 40
Figure 20 – Test sequence "ENABLE DEVICE TYPE: Application extended commands" . 41
Figure 21 – Test sequence 'ENABLE DEVICE TYPE: Application extended
configuration commands 1' . 42
Figure 22 – Test sequence 'ENABLE DEVICE TYPE: Application extended
configuration commands 2' . 43
Figure 23 – Subsequence 'Configure sequence' . 44
Figure 24 – Test sequence 'GO TO POINT N' . 45

62386-210 © IEC:2011 – 3 –
Figure 25 – Test sequence 'GO TO NEXT POINT' . 46
Figure 26 – Test sequence 'GO TO PREVIOUS POINT' . 47
Figure 27 – Test sequence 'Automatic sequence' . 48
Figure 28 – Timing diagram for test 'Automatic sequence' . 49
Figure 29 – Test sequence 'Automatic sequence – pointer' . 50
Figure 30 – Test sequence 'Automatic sequence – number of runs' . 51
Figure 31 – Test sequence 'Automatic sequence – stopped by command' . 52
Figure 32 – Test sequence 'Sequencer performance' . 53
Figure 33 – Template for 'Sequencer performance' . 53
Figure 34 – Test sequence 'START AT POINT N – number of runs' . 54
Figure 35 – Test sequence 'RESET SEQUENCER' . 55
Figure 36 – Test sequence 'RESET SEQUENCER – send twice / time-out' . 56
Figure 37 – Test sequence 'RESET SEQUENCER – command in-between' . 57
Figure 38 – Test sequence 'RESET CONTROL N' . 58
Figure 39 – Test sequence 'FAULTY CHANNEL' . 59
Figure 40 – Test sequence 'QUERY EXTENDED VERSION NUMBER' . 60
Figure 41 – Test sequence 'RESERVED APPLICATION EXTENDED COMMANDS' . 61

Table 1 – Access to the sequencer variables . 11
Table 2 – Sequencer programming example . 12
Table 3 – Declaration of variables . 14
Table 4 – Summary of the application extended command set . 23
Table 5 – Parameters for test sequence "Configure POINT N" . 26
Table 6 – Parameters for test sequence "Configuration – sent twice" . 27
Table 7 – Parameters for test sequence "Configuration – time-out" . 28
Table 8 – Parameters for test sequence "Configuration – command in-between 1" . 29
Table 9 – Parameters for test sequence "Configuration – command in-between 2" . 30
Table 10 – Parameters for test sequence "COPY TO POINT N" . 31
Table 11 – Parameters for test sequence "COPY TO POINT N – sent twice" . 32
Table 12 – Parameters for test sequence "COPY TO POINT N – time-out" . 33
Table 13 – Parameters for test sequence "COPY TO POINT N – command in-between" . 34
Table 16 – Parameters for test sequence "CHANNEL SELECTION – command in-
between". 37
Table 19 – Parameters for test sequence "CONFIGURE CONTROL N – command in-
between". 40
Table 20 – Parameters for test sequence "ENABLE DEVICE TYPE: Application
extended commands" . 41
Table 21 – Parameters for test sequence 'ENABLE DEVICE TYPE: Application
extended configuration commands 1' . 42
Table 23 – Parameters for subsequence 'Configure sequence' . 44
Table 24 – Parameters for test sequence 'GO TO POINT N' . 45
Table 27 – Parameters for test sequence 'Automatic sequence' .
...