Radio frequency and coaxial cable assemblies - Part 1: Generic specification - General requirements and test methods

IEC 60966-1:2019 is available as IEC 60966-1:2019 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.
IEC 60966-1:2019 specifies requirements for radio frequency coaxial cable assemblies operating in the transverse electromagnetic mode (TEM) and establishes general requirements for testing the electrical, mechanical and environmental properties of radio frequency coaxial cable assemblies composed of cables and connectors. Additional requirements relating to specific families of cable assemblies are given in the relevant sectional specifications. This third edition cancels and replaces the second edition published in 1999. This edition includes the following significant technical changes with respect to the previous edition:
a) measurement method for screening effectiveness was cancelled;
b) give references to relevant test procedures for transfer impedance and screening attenuation

Cordons coaxiaux et cordons pour fréquences radioélectiques - Partie 1: Spécification générique - Exigences générales et méthodes d'essai

IEC 60966-1:2019 est disponible sous forme de IEC 60966-1:2019 RLV qui contient la Norme internationale et sa version Redline, illustrant les modifications du contenu technique depuis l'édition précédente.
L'IEC 60966-1:2019 définit les exigences relatives aux cordons coaxiaux et aux cordons pour fréquences radioélectriques travaillant en mode électromagnétique transversal (TEM: Transverse Electromagnetic Mode). Elle fixe des exigences générales pour contrôler les propriétés électriques, mécaniques et environnementales des cordons coaxiaux pour fréquences radioélectriques composés de câbles et de connecteurs. Des exigences supplémentaires relatives à des familles spécifiques de cordons figurent dans les spécifications intermédiaires applicables. Cette troisième édition annule et remplace la deuxième édition parue en 1999. Cette édition inclut les modifications techniques majeures suivantes par rapport à l'édition précédente:
a) méthode de mesure de l’efficacité d’écran a été retiree;
b) donne les références aux procédures d'essai applicables pour impedance de transfert and affaiblissement d'écran.

General Information

Status
Published
Publication Date
07-Feb-2019
Current Stage
PPUB - Publication issued
Start Date
16-Nov-2018
Completion Date
08-Feb-2019
Ref Project

Relations

Buy Standard

Standard
IEC 60966-1:2019 RLV - Radio frequency and coaxial cable assemblies - Part 1: Generic specification - General requirements and test methods Released:2/8/2019 Isbn:9782832265604
English language
168 pages
sale 15% off
Preview
sale 15% off
Preview
Standard
IEC 60966-1:2019 - Radio frequency and coaxial cable assemblies - Part 1: Generic specification - General requirements and test methods
English and French language
107 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)


IEC 60966-1 ®
Edition 3.0 2019-02
REDLINE VERSION
INTERNATIONAL
STANDARD
colour
inside
Radio frequency and coaxial cable assemblies –
Part 1: Generic specification – General requirements and test methods

All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form
or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from
either IEC or IEC's member National Committee in the country of the requester. If you have any questions about IEC
copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or
your local IEC member National Committee for further information.

IEC Central Office Tel.: +41 22 919 02 11
3, rue de Varembé info@iec.ch
CH-1211 Geneva 20 www.iec.ch
Switzerland
About the IEC
The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes
International Standards for all electrical, electronic and related technologies.

About IEC publications
The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the
latest edition, a corrigendum or an amendment might have been published.

IEC publications search - webstore.iec.ch/advsearchform Electropedia - www.electropedia.org
The advanced search enables to find IEC publications by a The world's leading online dictionary on electrotechnology,
variety of criteria (reference number, text, technical containing more than 22 000 terminological entries in English
committee,…). It also gives information on projects, replaced and French, with equivalent terms in 16 additional languages.
and withdrawn publications. Also known as the International Electrotechnical Vocabulary

(IEV) online.
IEC Just Published - webstore.iec.ch/justpublished
Stay up to date on all new IEC publications. Just Published IEC Glossary - std.iec.ch/glossary
details all new publications released. Available online and 67 000 electrotechnical terminology entries in English and
once a month by email. French extracted from the Terms and Definitions clause of
IEC publications issued since 2002. Some entries have been
IEC Customer Service Centre - webstore.iec.ch/csc collected from earlier publications of IEC TC 37, 77, 86 and
If you wish to give us your feedback on this publication or CISPR.

need further assistance, please contact the Customer Service

Centre: sales@iec.ch.
IEC 60966-1 ®
Edition 3.0 2019-02
REDLINE VERSION
INTERNATIONAL
STANDARD
colour
inside
Radio frequency and coaxial cable assemblies –

Part 1: Generic specification – General requirements and test methods

INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
ICS 33.120.10 ISBN 978-2-8322-6560-4

– 2 – IEC 60966-1:2019 RLV © IEC 2019
CONTENTS
FOREWORD . 7
1 Scope . 9
2 Normative references . 9
3 Terms and definitions . 9
4 Design and manufacturing requirements . 13
4.1 Cable design and construction . 13
4.2 Connector design and construction . 13
4.3 Outline and interface dimensions . 13
5 Workmanship, marking and packaging . 13
5.1 Workmanship . 13
5.2 Marking . 14
5.3 End caps. 14
5.4 Packaging and labelling . 14
6 Quality assessment management . 14
7 Test methods – General . 14
7.1 Standard atmospheric conditions for testing . 14
7.2 Visual inspection . 15
7.3 Dimensions inspection . 15
7.3.1 Interface dimensions . 15
7.3.2 Outline dimensions . 15
8 Electrical tests . 15
8.1 Reflection properties . 15
8.1.1 Object . 15
8.1.2 Test equipment . 15
8.1.3 Procedure . 16
8.1.4 Requirements . 16
8.1.5 Information to be given in the detail specification . 16
8.2 Uniformity of impedance . 17
8.2.1 Object . 17
8.2.2 Procedure . 17
8.2.3 Requirements . 17
8.2.4 Information to be given in the detail specification . 17
8.3 Insertion loss . 17
8.3.1 Procedure . 17
8.3.2 Requirements . 17
8.3.3 Information to be given in the detail specification . 17
8.4 Insertion loss stability . 17
8.4.1 Object . 17
8.4.2 Procedure . 17
8.4.3 Requirements . 17
8.4.4 Information to be given in the detail specification . 17
8.5 Propagation time . 18
8.5.1 Procedure . 18
8.5.2 Requirements . 18
8.5.3 Information to be given in the detail specification . 18

8.6 Stability of electrical length . 18
8.6.1 Object . 18
8.6.2 Procedures . 18
8.6.3 Requirements . 21
8.6.4 Information to be given in the detail specification . 22
8.7 Phase difference . 22
8.7.1 Object . 22
8.7.2 Procedure . 22
8.7.3 Requirements . 22
8.7.4 Information to be given in the detail specification . 22
8.8 Phase variation with temperature . 22
8.8.1 Object . 22
8.8.2 Procedure . 22
8.8.3 Requirements . 22
8.8.4 Information to be given in the detail specification . 22
8.9 Screening effectiveness . 23
8.9.1 Transfer impedance . 23
8.9.2 Screening attenuation . 23
8.10 Voltage proof . 23
8.10.1 Procedure . 23
8.10.2 Requirements . 23
8.10.3 Information to be given in the detail specification . 23
8.11 Insulation resistance . 24
8.11.1 Procedure . 24
8.11.2 Requirements . 24
8.11.3 Information to be given in the detail specification . 24
8.12 Inner and outer conductor continuity . 24
8.12.1 Object . 24
8.12.2 Procedure . 24
8.12.3 Requirements . 24
8.12.4 Information to be given in the detail specification . 24
8.13 Power rating . 24
8.13.1 Object . 24
8.13.2 Procedure . 25
8.13.3 Requirements . 25
8.13.4 Information to be given in the detail specification . 25
8.14 Intermodulation level measurement . 25
8.14.1 Procedure . 25
8.14.2 Requirements . 25
8.14.3 Information to be given in the detail specification . 25
9 Mechanical robustness tests . 25
9.1 Tensile . 25
9.1.1 Object . 25
9.1.2 Procedure . 26
9.1.3 Requirements . 26
9.1.4 Information to be given in the detail specification . 26
9.2 Flexure . 26
9.2.1 Object . 26
9.2.2 Procedure . 26
...


IEC 60966-1 ®
Edition 3.0 2019-02
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
colour
inside
Radio frequency and coaxial cable assemblies –
Part 1: Generic specification – General requirements and test methods

Cordons coaxiaux et cordons pour fréquences radioélectriques –
Partie 1: Spécification générique – Exigences générales et méthodes d’essai

All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form
or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from
either IEC or IEC's member National Committee in the country of the requester. If you have any questions about IEC
copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or
your local IEC member National Committee for further information.

Droits de reproduction réservés. Sauf indication contraire, aucune partie de cette publication ne peut être reproduite
ni utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie
et les microfilms, sans l'accord écrit de l'IEC ou du Comité national de l'IEC du pays du demandeur. Si vous avez des
questions sur le copyright de l'IEC ou si vous désirez obtenir des droits supplémentaires sur cette publication, utilisez
les coordonnées ci-après ou contactez le Comité national de l'IEC de votre pays de résidence.

IEC Central Office Tel.: +41 22 919 02 11
3, rue de Varembé info@iec.ch
CH-1211 Geneva 20 www.iec.ch
Switzerland
About the IEC
The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes
International Standards for all electrical, electronic and related technologies.

About IEC publications
The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the
latest edition, a corrigenda or an amendment might have been published.

IEC Catalogue - webstore.iec.ch/catalogue Electropedia - www.electropedia.org
The stand-alone application for consulting the entire The world's leading online dictionary of electronic and
bibliographical information on IEC International Standards, electrical terms containing 21 000 terms and definitions in
Technical Specifications, Technical Reports and other English and French, with equivalent terms in 16 additional
documents. Available for PC, Mac OS, Android Tablets and languages. Also known as the International Electrotechnical
iPad. Vocabulary (IEV) online.

IEC publications search - webstore.iec.ch/advsearchform IEC Glossary - std.iec.ch/glossary
The advanced search enables to find IEC publications by a 67 000 electrotechnical terminology entries in English and
variety of criteria (reference number, text, technical French extracted from the Terms and Definitions clause of
committee,…). It also gives information on projects, replaced IEC publications issued since 2002. Some entries have been
and withdrawn publications. collected from earlier publications of IEC TC 37, 77, 86 and

CISPR.
IEC Just Published - webstore.iec.ch/justpublished

Stay up to date on all new IEC publications. Just Published IEC Customer Service Centre - webstore.iec.ch/csc
details all new publications released. Available online and If you wish to give us your feedback on this publication or
also once a month by email. need further assistance, please contact the Customer Service
Centre: sales@iec.ch.
A propos de l'IEC
La Commission Electrotechnique Internationale (IEC) est la première organisation mondiale qui élabore et publie des
Normes internationales pour tout ce qui a trait à l'électricité, à l'électronique et aux technologies apparentées.

A propos des publications IEC
Le contenu technique des publications IEC est constamment revu. Veuillez vous assurer que vous possédez l’édition la
plus récente, un corrigendum ou amendement peut avoir été publié.

Catalogue IEC - webstore.iec.ch/catalogue Electropedia - www.electropedia.org
Application autonome pour consulter tous les renseignements
Le premier dictionnaire en ligne de termes électroniques et
bibliographiques sur les Normes internationales,
électriques. Il contient 21 000 termes et définitions en anglais
Spécifications techniques, Rapports techniques et autres
et en français, ainsi que les termes équivalents dans 16
documents de l'IEC. Disponible pour PC, Mac OS, tablettes
langues additionnelles. Egalement appelé Vocabulaire
Android et iPad.
Electrotechnique International (IEV) en ligne.

Recherche de publications IEC -
Glossaire IEC - std.iec.ch/glossary
webstore.iec.ch/advsearchform
67 000 entrées terminologiques électrotechniques, en anglais
La recherche avancée permet de trouver des publications IEC et en français, extraites des articles Termes et Définitions des
en utilisant différents critères (numéro de référence, texte, publications IEC parues depuis 2002. Plus certaines entrées
comité d’études,…). Elle donne aussi des informations sur les antérieures extraites des publications des CE 37, 77, 86 et
projets et les publications remplacées ou retirées. CISPR de l'IEC.

IEC Just Published - webstore.iec.ch/justpublished Service Clients - webstore.iec.ch/csc
Restez informé sur les nouvelles publications IEC. Just Si vous désirez nous donner des commentaires sur cette
Published détaille les nouvelles publications parues. publication ou si vous avez des questions contactez-nous:
Disponible en ligne et aussi une fois par mois par email. sales@iec.ch.

IEC 60966-1 ®
Edition 3.0 2019-02
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
colour
inside
Radio frequency and coaxial cable assemblies –

Part 1: Generic specification – General requirements and test methods

Cordons coaxiaux et cordons pour fréquences radioélectriques –

Partie 1: Spécification générique – Exigences générales et méthodes d’essai

INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 33.120.10 ISBN 978-2-8322-6259-7

– 2 – IEC 60966-1:2019 © IEC 2019
CONTENTS
FOREWORD . 7
1 Scope . 9
2 Normative references . 9
3 Terms and definitions . 10
4 Design and manufacturing requirements . 12
4.1 Cable design and construction . 12
4.2 Connector design and construction . 12
4.3 Outline and interface dimensions . 13
5 Workmanship, marking and packaging . 13
5.1 Workmanship . 13
5.2 Marking . 13
5.3 End caps. 13
5.4 Packaging and labelling . 13
6 Quality management . 13
7 Test methods – General . 13
7.1 Standard atmospheric conditions for testing . 13
7.2 Visual inspection . 14
7.3 Dimensions inspection . 14
7.3.1 Interface dimensions . 14
7.3.2 Outline dimensions . 14
8 Electrical tests . 15
8.1 Reflection properties . 15
8.1.1 Object . 15
8.1.2 Test equipment . 15
8.1.3 Procedure . 15
8.1.4 Requirements . 16
8.1.5 Information to be given in the detail specification . 16
8.2 Uniformity of impedance . 16
8.2.1 Object . 16
8.2.2 Procedure . 16
8.2.3 Requirements . 16
8.2.4 Information to be given in the detail specification . 16
8.3 Insertion loss . 16
8.3.1 Procedure . 16
8.3.2 Requirements . 16
8.3.3 Information to be given in the detail specification . 16
8.4 Insertion loss stability . 17
8.4.1 Object . 17
8.4.2 Procedure . 17
8.4.3 Requirements . 17
8.4.4 Information to be given in the detail specification . 17
8.5 Propagation time . 17
8.5.1 Procedure . 17
8.5.2 Requirements . 17
8.5.3 Information to be given in the detail specification . 17

8.6 Stability of electrical length . 17
8.6.1 Object . 17
8.6.2 Procedures . 17
8.6.3 Requirements . 19
8.6.4 Information to be given in the detail specification . 19
8.7 Phase difference . 19
8.7.1 Object . 19
8.7.2 Procedure . 19
8.7.3 Requirements . 19
8.7.4 Information to be given in the detail specification . 20
8.8 Phase variation with temperature . 20
8.8.1 Object . 20
8.8.2 Procedure . 20
8.8.3 Requirements . 20
8.8.4 Information to be given in the detail specification . 20
8.9 Screening effectiveness . 20
8.9.1 Transfer impedance . 20
8.9.2 Screening attenuation . 20
8.10 Voltage proof . 21
8.10.1 Procedure . 21
8.10.2 Requirements .
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.