ISO 11553-2:2013

Safety of machinery -- Laser processing machines -- Part 2: Safety requirements for hand-held laser processing devices

ISO 11553-2:2007 specifies the requirements for laser processing devices, as defined in ISO 11553-1, which are hand-held or hand-operated. The purpose of ISO 11553-2:2007 is to draw attention to the particular hazards related to the use of hand-held laser and hand-operated laser processing devices and to prevent personal injury. This includes both the areas of hazard analysis and risk assessment as well as protective measures.

General Information

• Status: Published
• Publication Date: 16-Sep-2013
• ICS: 01 - GENERALITIES. TERMINOLOGY. STANDARDIZATION. DOCUMENTATION
• ICS: 13.110 - Safety of machinery
• ICS: 31.220.10 - Plug-and-socket devices. Connectors
• ICS: 31.260 - Optoelectronics. Laser equipment
• Technical Committee: TC 76 - Optical radiation safety and laser equipment
• Current Stage: PPUB - Publication issued
• Start Date: 31-Jan-2007
• Completion Date: 31-Jan-2007

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 11553-2
First edition
2007-03-01
Corrected version
2008-03-01

Safety of machinery — Laser processing
machines —
Part 2:
Safety requirements for hand-held laser
processing devices
Sécurité des machines — Machines à laser —
Partie 2: Exigences de sécurité pour dispositifs de traitement laser
portatifs




Reference number
ISO 11553-2:2007(E)
©
ISO 2007

---------------------- Page: 1 ----------------------
ISO 11553-2:2007(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.


©  ISO 2007
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail [e-mail]
Web www.iso.org
Published in Switzerland

ii © ISO 2007 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 11553-2:2007(E)
Contents Page
Foreword. iv
Introduction . v
1 Scope .1
2 Normative references .1
3 Terms and definitions .2
4 Hazards .2
4.1 Inherent hazards .2
4.2 Hazards induced by external effects (interferences) .3
4.3 Further hazards related to the use of hand-held laser processing devices.4
5 Safety requirements and measures.4
5.1 General requirements.4
5.2 Risk assessment.5
5.3 Implementation of corrective measures.5
5.4 Design requirements .7
6 Verification of safety requirements and measures .11
6.1 General conformance.11
6.2 Control category classification .11
6.3 Laser classification .12
7 Information for the user .12
7.1 Additional requirements .
...