IEC 62419:2008
(Main)Control technology - Rules for the designation of measuring instruments
Control technology - Rules for the designation of measuring instruments
IEC 62419:2008 is applicable to measurement technology. It defines rules for the unambiguous designation of different types of measuring instruments and of measuring instrument features with the intention of enabling unambiguous technical communication over language boundaries. This standard cancels and replaces IEC/PAS 62419 published in 2005. This first edition constitutes a technical revision.
Technologie de commande et de régulation - Règles pour la désignation des instruments de mesure
L'IEC 62419:2008 s'applique à la technologie de mesure. Elle définit les règles pour une désignation claire des différents types d'instruments de mesure et des caractéristiques des instruments de mesure, dans le but de permettre une communication technique dénuée d'ambiguïté au-delà des barrières linguistiques. La présente norme annule et remplace la CEI/PAS 62419 parue en 2005. Cette première édition constitue une révision technique. La présente version bilingue (2014-04) correspond à la version anglaise monolingue publiée en 2008-11.
General Information
Relations
Buy Standard
Standards Content (Sample)
IEC 62419
Edition 1.0 2008-11
INTERNATIONAL
STANDARD
Control technology – Rules for the designation of measuring instruments
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form
or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from
either IEC or IEC's member National Committee in the country of the requester.
If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication,
please contact the address below or your local IEC member National Committee for further information.
IEC Central Office
3, rue de Varembé
CH-1211 Geneva 20
Switzerland
Email: inmail@iec.ch
Web: www.iec.ch
About the IEC
The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes
International Standards for all electrical, electronic and related technologies.
About IEC publications
The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the
latest edition, a corrigenda or an amendment might have been published.
ƒ Catalogue of IEC publications: www.iec.ch/searchpub
The IEC on-line Catalogue enables you to search by a variety of criteria (reference number, text, technical committee,…).
It also gives information on projects, withdrawn and replaced publications.
ƒ IEC Just Published: www.iec.ch/online_news/justpub
Stay up to date on all new IEC publications. Just Published details twice a month all new publications released. Available
on-line and also by email.
ƒ Electropedia: www.electropedia.org
The world's leading online dictionary of electronic and electrical terms containing more than 20 000 terms and definitions
in English and French, with equivalent terms in additional languages. Also known as the International Electrotechnical
Vocabulary online.
ƒ Customer Service Centre: www.iec.ch/webstore/custserv
If you wish to give us your feedback on this publication or need further assistance, please visit the Customer Service
Centre FAQ or contact us:
Email: csc@iec.ch
Tel.: +41 22 919 02 11
Fax: +41 22 919 03 00
IEC 62419
Edition 1.0 2008-11
INTERNATIONAL
STANDARD
Control technology – Rules for the designation of measuring instruments
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
PRICE CODE
M
ICS 17.020; 25.040.40 ISBN 978-2-88910-698-1
– 2 – 62419 © IEC:2008(E)
CONTENTS
FOREWORD.3
INTRODUCTION.5
1 Scope and object.6
2 Normative references .6
3 Terms and definitions .7
4 Designation rules .8
4.1 General rules .8
4.2 Designation rules for measuring instruments .9
4.2.1 Designation rules for displaying measuring instruments.9
4.2.2 Designation rules for measuring instruments with signal output .9
4.3 Designation rules for measurement standards .10
4.4 Designation rules for measuring assemblies.10
4.5 Examples of terms of measuring instruments for complex measuring tasks .10
Annex A (informative) Examples of recommended terms.11
Bibliography.12
62419 © IEC:2008(E) – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
CONTROL TECHNOLOGY –
RULES FOR THE DESIGNATION OF MEASURING INSTRUMENTS
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any
equipment declared to be in conformity with an IEC Publication.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 62419 has been prepared by IEC technical committee 65:
Industrial-process measurement, control and automation.
This standard cancels and replaces IEC/PAS 62419 published in 2005. This first edition
constitutes a technical revision.
The text of this standard is based on the following documents:
FDIS Report on voting
65/429/FDIS 65/430/RVD
Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.
This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.
– 4 – 62419 © IEC:2008(E)
The committee has decided that the contents of this publication will remain unchanged until
the maintenance result date indicated on the IEC web site under "http://webstore.iec.ch" in
the data related to the specific publication. At this date, the publication will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
A bilingual version of this publication may be issued at a later date.
62419 © IEC:2008(E) – 5 –
INTRODUCTION
The state of science concerning quantities and units has undergone significant changes in the
last century. During the period from 1920 to 1960 there was a fundamental change in the
comprehension and usage of physical quantities, which was particularly promoted by the
works of Julius Wallot published between 1922 and 1953. In this process the various systems
of physical units and the usage of numerical equations were replaced by the SI-units (see ISO
1000) and the usage of quantity equations. So the quantities were no longer linked to certain
units.
This development culminated in the publishing of the first edition of the German standard DIN
1313 Notation of physical equations in sciences and technology in 1931 and the resolutions of
the tenth general conference of weights and measures in 1954. Since then it has been
considered incorrect to address a quantity by its unit.
In view of this, measuring instruments should not be addressed by the unit of the measured
quantity but only by the measured quantity or the measuring task itself.
Referring to the question of market relevance, it must be stated, that especially with respect
to the international project of standardized classification and documentation in multilingual
equipment descriptions, it is important to critically address the situation regarding the
designation of measuring instruments. Ideally, every manufacturer should use the same
terminology. In practice, there is confusion in the proper designation of measuring instruments
within catalogues and sales brochures which also has consequences in technical literature.
It is not the intention of this standard to enforce particular usages in any language but to
make recommendations that remove the linguistic confusion in this field – or at least, reduce
it. Considering the urgent necessity of unambiguous technical communication over language
boundaries, this is a legitimate goal. This could also be considered to be a matter of global
importance.
– 6 – 62419 © IEC:2008(E)
CONTROL TECHNOLOGY –
RULES FOR THE DESIGNATION OF MEASURING INSTRUMENTS
1 Scope and object
This International Standard is applicable to measurement technology. It defines rules for the
unambiguous designation of different types of measuring instruments and of measuring
instrument features with the intention of enabling unambiguous technical communication over
language boundaries.
The scope of this International Standard is
– the adaptation of the designation of measuring instruments and of measuring instrument
features to the state of science by designating them according to the measuring quantity
or the measuring task instead of the unit, and
– the adaptation of the designation of measuring instruments and of measuring instrument
features to the terms given in the ISO/IEC Guide 99 (VIM).
It is strongly recommended that “……. measuring instrument” is used as secondary
component in compound terms. This is consistent with the objective of standardization,
namely uniformity, especially since the meaning of other secondary components, e.g.
“indicator”, “gauge”, “meter”, is no more descriptive than that of the standard component in
this context. For exceptions see 4.1 and A.2.
The ambiguous secondary component “. sensor” shall not be used. In its place one of the
secondary components “… sensing element”, “. detector”, “. transformer”, “. transducer”,
“… transmitter”, “. measuring instrument” or “. measuring chain” shall be used, depending
on the task of the functional unit being termed. The definitions for detector (detecting device),
transformer, transducer and transmitter are given in IEC 60050-351.
2 Normative references
The following referenced documents are indispensable for the application of this document.
For dated references, only the edition cited applies. For undated references, the latest edition
of the referenced document (including any amendments) applies.
IEC 60050-311, International Electrotechnical Vocabulary – Part 311: General terms relating
to measurements
IEC 60050-312, International Electrotechnical Vocabulary – Part 312: General terms relating
to electrical measurements
IEC 60050-351: 2006, International Electrotechnical Vocabulary – Part 351: Control
Technology
ISO/IEC Guide 99: 2007, International vocabulary of metrology – Basic and general concepts
and associated terms (VIM)
ISO 31 series, Quantities and units
ISO 1000, SI units and recommendations for the use of their multiples and of certain other
units
62419 © IEC:2008(E) – 7 –
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
3.1
measuring instrument
device intended to be used to make measurements, alone or in conjunction with
supplementary devices
[IEV 311-03-01]
[ISO/IEC Guide 99, 3.1]
NOTE 1 Material measures are also measuring instruments.
NOTE 2 An instrument is also a measuring instrument if its output is transmitted, converted, processed or stored
and cannot be perceived directly by the observer.
NOTE 3 The designation measuring instrument without any supplementary designation components should only
be used as a generic term referring to all types of measuring instruments. In compound expressions, the term
“measuring instrument” should only be used to signify a displaying measuring instrument.
EXAMPLE The Measuring Instruments and Measuring Systems catalogue (also contains, for example, signal
generators and measuring assemblies).
3.1.1
displaying measuring instrument
displaying instrument
measuring instrument where the output signal is presented in visual form
[ISO/IEC Guide 99, 3.4 modified
...
IEC 62419 ®
Edition 1.0 2008-11
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Control technology – Rules for the designation of measuring instruments
Technologie de commande et de régulation – Règles pour la désignation des
instruments de mesure
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form
or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from
either IEC or IEC's member National Committee in the country of the requester. If you have any questions about IEC
copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or
your local IEC member National Committee for further information.
Droits de reproduction réservés. Sauf indication contraire, aucune partie de cette publication ne peut être reproduite
ni utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie
et les microfilms, sans l'accord écrit de l'IEC ou du Comité national de l'IEC du pays du demandeur. Si vous avez des
questions sur le copyright de l'IEC ou si vous désirez obtenir des droits supplémentaires sur cette publication, utilisez
les coordonnées ci-après ou contactez le Comité national de l'IEC de votre pays de résidence.
IEC Central Office Tel.: +41 22 919 02 11
3, rue de Varembé Fax: +41 22 919 03 00
CH-1211 Geneva 20 info@iec.ch
Switzerland www.iec.ch
About the IEC
The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes
International Standards for all electrical, electronic and related technologies.
About IEC publications
The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the
latest edition, a corrigenda or an amendment might have been published.
IEC Catalogue - webstore.iec.ch/catalogue Electropedia - www.electropedia.org
The stand-alone application for consulting the entire The world's leading online dictionary of electronic and
bibliographical information on IEC International Standards, electrical terms containing more than 30 000 terms and
Technical Specifications, Technical Reports and other definitions in English and French, with equivalent terms in 14
documents. Available for PC, Mac OS, Android Tablets and additional languages. Also known as the International
iPad. Electrotechnical Vocabulary (IEV) online.
IEC publications search - www.iec.ch/searchpub IEC Glossary - std.iec.ch/glossary
The advanced search enables to find IEC publications by a More than 55 000 electrotechnical terminology entries in
variety of criteria (reference number, text, technical English and French extracted from the Terms and Definitions
committee,…). It also gives information on projects, replaced clause of IEC publications issued since 2002. Some entries
and withdrawn publications. have been collected from earlier publications of IEC TC 37,
77, 86 and CISPR.
IEC Just Published - webstore.iec.ch/justpublished
Stay up to date on all new IEC publications. Just Published IEC Customer Service Centre - webstore.iec.ch/csc
details all new publications released. Available online and If you wish to give us your feedback on this publication or
also once a month by email. need further assistance, please contact the Customer Service
Centre: csc@iec.ch.
A propos de l'IEC
La Commission Electrotechnique Internationale (IEC) est la première organisation mondiale qui élabore et publie des
Normes internationales pour tout ce qui a trait à l'électricité, à l'électronique et aux technologies apparentées.
A propos des publications IEC
Le contenu technique des publications IEC est constamment revu. Veuillez vous assurer que vous possédez l’édition la
plus récente, un corrigendum ou amendement peut avoir été publié.
Catalogue IEC - webstore.iec.ch/catalogue Electropedia - www.electropedia.org
Application autonome pour consulter tous les renseignements
Le premier dictionnaire en ligne de termes électroniques et
bibliographiques sur les Normes internationales,
électriques. Il contient plus de 30 000 termes et définitions en
Spécifications techniques, Rapports techniques et autres
anglais et en français, ainsi que les termes équivalents dans
documents de l'IEC. Disponible pour PC, Mac OS, tablettes
14 langues additionnelles. Egalement appelé Vocabulaire
Android et iPad.
Electrotechnique International (IEV) en ligne.
Recherche de publications IEC - www.iec.ch/searchpub
Glossaire IEC - std.iec.ch/glossary
La recherche avancée permet de trouver des publications IEC Plus de 55 000 entrées terminologiques électrotechniques, en
en utilisant différents critères (numéro de référence, texte, anglais et en français, extraites des articles Termes et
comité d’études,…). Elle donne aussi des informations sur les Définitions des publications IEC parues depuis 2002. Plus
projets et les publications remplacées ou retirées. certaines entrées antérieures extraites des publications des
CE 37, 77, 86 et CISPR de l'IEC.
IEC Just Published - webstore.iec.ch/justpublished
Service Clients - webstore.iec.ch/csc
Restez informé sur les nouvelles publications IEC. Just
Published détaille les nouvelles publications parues. Si vous désirez nous donner des commentaires sur cette
Disponible en ligne et aussi une fois par mois par email. publication ou si vous avez des questions contactez-nous:
csc@iec.ch.
IEC 62419 ®
Edition 1.0 2008-11
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Control technology – Rules for the designation of measuring instruments
Technologie de commande et de régulation – Règles pour la désignation des
instruments de mesure
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
PRICE CODE
INTERNATIONALE
CODE PRIX M
ICS 17.020; 25.040.40 ISBN 978-2-8322-1458-9
– 2 – IEC 62419:2008 © IEC 2008
CONTENTS
FOREWORD . 3
INTRODUCTION . 5
1 Scope and object . 6
2 Normative references . 6
3 Terms and definitions . 7
4 Designation rules . 8
4.1 General rules . 8
4.2 Designation rules for measuring instruments . 9
4.2.1 Designation rules for displaying measuring instruments . 9
4.2.2 Designation rules for measuring instruments with signal output . 9
4.3 Designation rules for measurement standards . 10
4.4 Designation rules for measuring assemblies . 10
4.5 Examples of terms of measuring instruments for complex measuring tasks . 10
Annex A (informative) Examples of recommended terms . 11
Bibliography . 12
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
CONTROL TECHNOLOGY –
RULES FOR THE DESIGNATION OF MEASURING INSTRUMENTS
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any
equipment declared to be in conformity with an IEC Publication.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 62419 has been prepared by IEC technical committee 65:
Industrial-process measurement, control and automation. This standard cancels and replaces
IEC/PAS 62419 published in 2005. This first edition constitutes a technical revision.
This bilingual version (2014-04) corresponds to the monolingual English version, published in
2008-11.
The text of this standard is based on the following documents:
FDIS Report on voting
65/429/FDIS 65/430/RVD
Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.
The French version of this standard has not been voted upon.
– 4 – IEC 62419:2008 © IEC 2008
This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.
The committee has decided that the contents of this publication will remain unchanged until
the maintenance result date indicated on the IEC web site under "http://webstore.iec.ch" in
the data related to the specific publication. At this date, the publication will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
INTRODUCTION
The state of science concerning quantities and units has undergone significant changes in the
last century. During the period from 1920 to 1960 there was a fundamental change in the
comprehension and usage of physical quantities, which was particularly promoted by the
works of Julius Wallot published between 1922 and 1953. In this process the various systems
of physical units and the usage of numerical equations were replaced by the SI-units (see ISO
1000) and the usage of quantity equations. So the quantities were no longer linked to certain
units.
This development culminated in the publishing of the first edition of the German standard DIN
1313 Notation of physical equations in sciences and technology in 1931 and the resolutions of
the tenth general conference of weights and measures in 1954. Since then it has been
considered incorrect to address a quantity by its unit.
In view of this, measuring instruments should not be addressed by the unit of the measured
quantity but only by the measured quantity or the measuring task itself.
Referring to the question of market relevance, it must be stated, that especially with respect
to the international project of standardized classification and documentation in multilingual
equipment descriptions, it is important to critically address the situation regarding the
designation of measuring instruments. Ideally, every manufacturer should use the same
terminology. In practice, there is confusion in the proper designation of measuring instruments
within catalogues and sales brochures which also has consequences in technical literature.
It is not the intention of this standard to enforce particular usages in any language but to
make recommendations that remove the linguistic confusion in this field
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.