IEC 60364-5-53:2019/AMD2:2024

Amendment 2 - Low-voltage electrical installations - Part 5-53: Selection and erection of electrical equipment - Devices for protection for safety, isolation, switching, control and monitoring

Amendement 2 - Installations électriques à basse tension - Partie 5-53 : Choix et mise en œuvre des matériels électriques - Dispositifs de protection pour assurer la sécurité, le sectionnement, la coupure, la commande et la surveillance

General Information

• Status: Published
• Publication Date: 17-Dec-2024
• ICS: 29.130.01 - Switchgear and controlgear in general
• ICS: 91.140.50 - Electricity supply systems
• Technical Committee: TC 64 - Electrical installations and protection against electric shock
• Drafting Committee: MT 3 - TC 64/MT 3
• Current Stage: PPUB - Publication issued
• Start Date: 10-Jan-2025
• Completion Date: 18-Dec-2024

Relations

• Amends: IEC 60364-5-53:2019 - Low-voltage electrical installations - Part 5-53: Selection and erection of electrical equipment - Devices for protection for safety, isolation, switching, control and monitoring
• Effective Date: 05-Sep-2023

Standards Content (Sample)

IEC 60364-5-53 ®
Edition 4.0 2024-12
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
AMENDMENT 2
AMENDEMENT 2
Low-voltage electrical installations –
Part 5-53: Selection and erection of electrical equipment – Devices for protection
for safety, isolation, switching, control and monitoring

Installations électriques à basse tension –
Partie 5-53: Choix et mise en œuvre des matériels électriques – Dispositifs de
protection pour assurer la sécurité, le sectionnement, la coupure, la commande
et la surveillance
IEC 60364-5-53:2019-02/AMD2:2024-12(en-fr)

All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form
or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from
either IEC or IEC's member National Committee in the country of the requester. If you have any questions about IEC
copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or
your local IEC member National Committee for further information.

Droits de reproduction réservés. Sauf indication contraire, aucune partie de cette publication ne peut être reproduite ni
utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie et
les microfilms, sans l'accord écrit de l'IEC ou du Comité national de l'IEC du pays du demandeur. Si vous avez des
questions sur le copyright de l'IEC ou si vous désirez obtenir des droits supplémentaires sur cette publication, utilisez
les coordonnées ci-après ou contactez le Comité national de l'IEC de votre pays de résidence.

IEC Secretariat Tel.: [phone]
3, rue de Varembé [e-mail]
CH-1211 Geneva 20 www.iec.ch
Switzerland
About the IEC
The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes
International Standards for all electrical, electronic and related technologies.

About IEC publications
The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the
latest edition, a corrigendum or an amendment might have been published.

IEC publications search - webstore.iec.ch/advsearchform IEC Products & Services Portal - products.iec.ch
The advanced search enables to find IEC publications by a Discover our powerful search engine and read freely all the
variety of criteria (reference number, text, technical publications previews, graphical symbols and the glossary.
committee, …). It also gives information on projects, replaced With a subscription you will always have access to up to date
and withdrawn publications. content tailored to your needs.

IEC Just Published - webstore.iec.ch/justpublished
Electropedia - www.electropedia.org
Stay up to date on all new IEC publications. Just Published
The world's leading online dictionary on electrotechnology,
details all new publications released. Available online and once
containing more than 22 500 terminological entries in English
a month by email.
and French, with equivalent terms in 25 additional languages.

Also known as the International Electrotechnical Vocabulary
IEC Customer Service Centre - webstore.iec.ch/csc
(IEV) online.
If you wish to give us your feedback on this publication or need

further assistance, please contact the Customer Service
Centre: [e-mail].
A propos de l'IEC
La Commission Electrotechnique Internationale (IEC) est la première organisation mondiale qui élabore et publie des
Normes internationales pour tout ce qui a trait à l'électricité, à l'électronique et aux technologies apparentées.

A propos des publications IEC
Le contenu technique des publications IEC est constamment revu. Veuillez vous assurer que vous possédez l’édition la
plus récente, un corrigendum ou amendement peut avoir été publié.

Recherche de publications IEC -  IEC Products & Services Portal - products.iec.ch
webstore.iec.ch/advsearchform Découvrez notre puissant moteur de recherche et consultez
La recherche avancée permet de trouver des publications IEC gratuitement tous les aperçus des publications, symboles
en utilisant différents critères (numéro de référence, texte, graphiques et le glossaire. Avec un abonnement, vous aurez
comité d’études, …). Elle donne aussi des informations sur les toujours accès à un contenu à jour adapté à vos besoins.
projets et les publications remplacées ou retirées.

Electropedia - www.electropedia.org
IEC Just Published - webstore.iec.ch/justpublished
Le premier dictionnaire d'électrotechnologie en ligne au monde,
Restez informé sur les nouvelles publications IEC. Just
avec plus de 22 500 articles terminologiques en anglais et en
Published détaille les nouvelles publications parues.
français, ainsi que les termes équivalents dans 25 langues
Disponible en ligne et une fois par mois par email.
additionnelles. Egalement appelé Vocabulaire

Electrotechnique International (IEV) en ligne.
Service Clients - webstore.iec.ch/csc

Si vous désirez nous donner des commentaires sur cette
publication ou si vous avez des questions contactez-nous:
[e-mail].
IEC 60364-5-53 ®
Edition 4.0 2024-12
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
AMENDMENT 2
AMENDEMENT 2
Low-voltage electrical installations –

Part 5-53: Selection and erection of electrical equipment – Devices for protection

for safety, isolation, switching, control and monitoring

Installations électriques à basse tension –

Partie 5-53: Choix et mise en œuvre des matériels électriques – Dispositifs de

protection pour assurer la sécurité, le sectionnement, la coupure, la commande

et la surveillance
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 29.130.01, 91.140.50 ISBN 978-2-8327-0097-6

– 2 – IEC 60364-5-53:2019/AMD2:2024
© IEC 2024
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
LOW-VOLTAGE ELECTRICAL INSTALLATIONS –

Part 5-53: Selection and erection of electrical equipment – Devices
for protection for safety, isolation, switching, control and monitoring

AMENDMENT 2
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international
co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and
in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports,
Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their
preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with
may participate in this preparatory work. International, governmental and non-governmental organizations liaising
with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for
Standardization (ISO) in accordance with conditions determined by agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence between
any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) IEC draws attention to the possibility that the implementation of this document may involve the use of (a)
patent(s). IEC takes no position concerning the evidence, validity or applicability of any claimed patent rights in
respect thereof. As of the date of publication of this document, IEC had not received notice of (a) patent(s), which
may be required to implement this document. However, implementers are cautioned that this may not represent
the latest information, which may be obtained from the patent database available at https://patents.iec.ch. IEC
shall not be held responsible for identifying any or all such patent rights.
Amendment 2 to IEC 60364-5-53:2019 has been prepared by IEC technical committee 64:
Electrical installations and protection against electric shock.
The text of this Amendment is based on the following documents:
Draft Report on voting
64/2648/FDIS 64/2738/RVD
Full information on the voting for its approval can be found in the report on voting indicated in
the above table.
© IEC 2024
The language used for the development of this Amendment is English.
This document was drafted in accordance with ISO/IEC Directives, Part 2, and developed in
accordance with ISO/IEC Directives, Part 1 and ISO/IEC Directives, IEC Supplement, available
at www.iec.ch/members_experts/refdocs. The main document types developed by IEC are
described in greater detail at www.iec.ch/publications/.
The committee has decided that the contents of this document will remain unchanged until the
stability date indicated on the IEC website under webstore.iec.ch in the data related to the
specific document. At this date, the document will be
• reconfirmed,
• withdrawn, or
• revised.
___________
534 Devices for protection against transient overvoltages
534.1 General
Replace the last paragraph with the following new paragraph:
Annex H provides additional information for the application of DC SPDs.
534.4.1 SPD location and SPD test class
Replace, in the sixth paragraph, "Table 1" with "IEC 60364-4-44:2024, Table 3"
534.4.4.1 General
Replace the last paragraph with the following paragraph:
SPDs for use in AC circuits shall comply with the requirements of IEC 61643-11.
Add the following new NOTE 2, and renumber the existing NOTE as NOTE 1:
NOTE 2 IEC 61643-41 Low-voltage surge protective devices – Part 41: Surge protective devices connected to DC
low-voltage power systems – Requirements and test methods, is under development.

– 4 – IEC 60364-5-53:2019/AMD2:2024
© IEC 2024
534.4.4.2 Selection of voltage protection level (U ) as a function of equipment rated
p
impulse voltage (U )
W
Replace the first paragraph, including NOTE 1, with the following paragraph:
The voltage protection level U of SPDs between live conductors and protective earthing
p
conductors shall be selected in accordance with the required rated impulse voltage of the
equipment and not exceed the value specified for overvoltage category II in accordance with
IEC 60364-4-44:2024, Table 4.
Replace the fourth paragraph with the following paragraph:
The voltage protection level provided by SPDs should not exceed 80 % of the required rated
impulse voltage of the equipment and the value specified for overvoltage category II in
accordance with IEC 60364-4-44:2024, Table 4.
Renumber the existing NOTE 2 as NOTE and delete the existing Table 1.

© IEC 2024
Insert, after Annex G, the following new Annex H:
Annex H
(informative)
Additional information for the application of DC SPDs
H.1 General
As there is a diversity of voltages used in DC systems, other system parameters may vary over
a wide range depending on the application, equipment and component used.
Owing to the varying parameters of such DC systems, only SPDs especially dedicated to DC
systems should be used. The manufacturer of SPDs should give the relevant information.
IEC 60364-4-44:2024, Clause 442 is applicable only for AC systems. For DC systems, which
are galvanically coupled to an AC system, it is necessary to consider how the potential
temporary overvoltages (TOVs) from the AC system and as specified in IEC 60364-4-44:2024,
Clause 442 are transferred to the DC system. For temporary overvoltages caused by faults
within a DC system, the corresponding data based on the DC system characteristics shall be
taken into consideration.
IEC 60364-4-44:2024, Clause 443 is applicable for both AC and DC applications and additional
requirements for DC systems are not necessary.
NOTE The specific risk of switching overvoltages in DC applications is under consideration.
Therefore, the parameters specified in Clause H.2 are provided for the selection and installation
of SPDs and the corresponding design of the installation.
H.2 Parameters for the selection of SP
...