IEC TR 60725:1981
(Main)Considerations on reference impedances for use in determining the disturbance characteristics of household appliances and similar electrical equipment
Considerations on reference impedances for use in determining the disturbance characteristics of household appliances and similar electrical equipment
Records the information that was available and the factors that were taken into account in arriving at the reference impedance of 0.4+ j 0.25 ohm which has been incorporated in IEC 60555. Has the status of a technical report.
Considérations sur les impédances de référence à utiliser pour la détermination des caractéristiques de perturbation des appareils électrodomestiques et les équipements analogues
Comprend les informations mises à disposition, ainsi que les facteurs pris en considération pour arriver à la valeur de l'impédance de référence de 0,4 + j 0,25 ohm qui a été incorporée dans la CEI 60555. Cette publication a le statut d'un rapport technique.
Considerations on reference for use in determining the disturbance characteristics of household appliances and similar electrical equipment
General Information
Relations
Standards Content (Sample)
SLOVENSKI SIST IEC/TR 60725:1998
prva izdaja
STANDARD
september 1998
Considerations on reference for use in determining the disturbance characteristics
of household appliances and similar electrical equipment
ICS 17.220.01 Referenčna št
...
This May Also Interest You
IEC 62153-4-7:2021 deals with the triaxial tube in tube method. This triaxial method is suitable to determine the surface transfer impedance and/or screening attenuation and coupling attenuation of mated screened connectors (including the connection between cable and connector) and cable assemblies. This method could also be extended to determine the transfer impedance, coupling or screening attenuation of balanced or multipin connectors and multicore cable assemblies. This third edition cancels and replaces the second edition published in 2015 and its Amendment 1:2018.This edition includes the following significant technical changes with respect to the previous edition:
- Annex E contains informative information about the direct measurement of screening effectiveness of connectors;
- Annex F gives normative information about mixed mode parameters;
- Annex G contains normative information about accessories for measuring coupling attenuation;
- Annex H discusses the low frequency screening attenuation.
- Standard174 pagesEnglish languagesale 15% off
- Standard136 pagesEnglish languagesale 15% off
- Standard114 pagesEnglish and French languagesale 15% off
- Standard15 pagesEnglish languagesale 15% off
- Standard15 pagesFrench languagesale 15% off
- Standard30 pagesEnglish and French languagesale 15% off
CISPR TR 16-4-4:2025 which is a Technical Report, establishes the CISPR model for the calculation of limits for the protection of radio services, based on data from the IEC Radio Services Database (RSD) and estimations of the input values for related probabilistic factors. This is part of the process of the derivation of disturbance limits in the radio frequency spectrum for use in publications containing emission requirements Application of this document leads to a frequency dependent limit result for a particular disturbance phenomenon and the considered product or product type establishing the technical basis in the CISPR limit specification procedure.
NOTE Non-technical parameters and terms that can be considered to influence a limit for inclusion in IEC publications are excluded from the modelling (see also Clause 4.6.5.3).
This third edition cancels and replaces the second edition published in 2007, Amendment 1:2017 and Amendment 2:2020. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition:
a) full revision of the limit calculation model;
b) the content on statistics of complaints was taken from this publication and published as separate document (CISPR TR 16-4-6);
c) application cases/rationales were separated from the model and will be handled in another document to be drafted.
- Technical report57 pagesEnglish languagesale 15% off
CISPR 16-1-4:2025 specifies the characteristics and performance of equipment for the measurement of radiated disturbances in the frequency range 9 kHz to 18 GHz. Specifications for antennas and test sites are included.
NOTE In accordance with IEC Guide 107. CISPR 16-1-4 is a basic EMC publication for use by product committees of the IEC. As stated in Guide 107, product committees are responsible for determining the applicability of the EMC standard. CISPR and its sub-committees are prepared to cooperate with product committees in the evaluation of the value of particular EMC tests for specific products.
The requirements of this publication apply at all frequencies and for all levels of radiated disturbances within the CISPR indicating range of the measuring equipment. Methods of measurement are covered in CISPR 16-2-3, further information on radio disturbance is given in CISPR TR 16-3, and uncertainties, statistics, and limit modelling are covered in CISPR 16-4 series. This fifth edition cancels and replaces the fourth edition published in 2019, Amendment 1:2020 and Amendment 2:2023. This edition constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous edition:
a) revision of the definition 3.1.7 and of the general introduction 8.1.1 for CMAD;
b) introduction of a new cable termination device, the very high frequency line impedance stabilization network (VHF-LISN) in 8.2;
c) addition of definition 3.1.34 for VHF-LISN, 3.1.20 for reference ground, 3.1.21 for reference ground plane and 3.1.31 for TN‑C‑S power system;
d) various non-technical editorial, style, and wording adjustments for consistency with drafting rules.
- Standard515 pagesEnglish languagesale 15% off
CISPR 12:2025 The limits in this document are designed to provide protection in the frequency range of 30 MHz to 1 000 MHz for off-board receivers. Compliance with this document does not guarantee adequate protection for receivers nearer than 10 m to the vehicle, boat or device. This document applies to the emission of electromagnetic energy that can cause interference to radio reception and which is emitted from:
1) vehicles propelled by an internal combustion engine (ICE), electrical means or both (see 3.1.34);
2) boats propelled by an ICE, electrical means or both (see 3.1.4). Boats are tested in the same manner as vehicles except where they have unique characteristics as explicitly stated in this document;
3) devices equipped with ICE (see 3.1.9). In the case of hybrid devices (e.g. equipped with both ICE and traction batteries), only the ICE mode is included in this document;
4) inboard and outboard boat engines and motors [i.e. equipped with ICE, electric motor (EM), or both], when marketed independently.
See Annex D for a flow chart and a list of examples to help determine the applicability of CISPR 12.
This document does not apply to aircraft, household appliances, medical devices, traction systems (railway engine or locomotive, streetcar or tram and electric trolley bus), vehicle, boat and device off-board chargers or to incomplete vehicles, boats and devices. In the case of a dual-mode trolley bus (e.g. propelled by power from either AC/DC mains or an ICE), the ICE propulsion system is included, but the EM propulsion portion of the vehicle is excluded from this document. In addition, domestic helper robots, such as household cleaning robots, hotel service robots and personal safety robots are also excluded from the scope of this document.
NOTE 1 Other than inboard or outboard boat engines and motors that are marketed independently, this document does not apply to components or incomplete products, such as an ICE, an incomplete vehicle or boat that has not yet been fitted with an ICE or EM, or spare parts. This document only applies to the final product, which is equipped with all applicable parts and components to be able to function as intended.
NOTE 2 Appliances without ICE for typical housekeeping and service functions in the household and similar environment are covered by the requirements of CISPR 14-1[1].
NOTE 3 Protection of receivers used on board the same vehicle as the disturbance source(s) are covered by CISPR 25[2].
This document does not prescribe measurement methods or limits for conducted disturbances, for the charging mode of operation, where the (electric or hybrid) vehicle or boat is connected to power mains, either directly (i.e. plug-in vehicle or boat) or indirectly (i.e. wireless power charging). The user is referred to appropriate IEC and CISPR standards, which define measurement techniques and limits for this condition.
NOTE 4 See IEC 61851-21-1[3] for road vehicles and IEC 61000-6-3[4], IEC 61000-6-4[5] and IEC 61000-6-8[6] for other types of vehicles or boats.
The emission requirements in this document are not applicable to the intentional transmissions from a radio transmitter, as defined by the ITU-R, including its spurious emissions.
Equipment that is covered by other CISPR product and product family emission standards are excluded from the scope of this document, except where they include ICE(s). In the latter case, the equipment complies with this document in all modes of operation where the ICE(s) is(are) active.
NOTE 5 The other CISPR product or product family emission standard can also apply to the equipment for those modes of operation where the ICE(s) is (are) not active. In case the ICE(s) is (are) always in operation, the other CISPR product or product family emission standard can still apply, for verifying the emissions from the other components and circuitry of the equipment.
Annex B and Annex C contain methods to evaluate the disturbance characteristics of high
- Standard91 pagesEnglish languagesale 15% off
- Standard102 pagesFrench languagesale 15% off
- Standard193 pagesEnglish and French languagesale 15% off
CISPR PAS 38:2025, which is a Publicly Available Specification, applies to radio beam wireless power transfer (RB‑WPT) as industrial, scientific, and medical equipment operating in the frequency range of 0 Hz to 400 GHz and designed to operate up to a distance of 10 m. This document covers emission requirements related to radio-frequency disturbances in the frequency range of 150 kHz to 18 GHz. Radio beam wireless power transfer devices are in the scope of this document only if they are not classified as radio apparatus.
NOTE 1 Wireless power transfer devices that use a modulated signal to transmit both power and information are classified as radio apparatus in most countries. While radio beam wireless power transfer devices are included in the scope of this document, these can be classified as radio apparatus in some countries, even if the transmitted signal is continuous wave, with no modulation. The user is advised to verify the applicable national radio regulations before applying this document for these types of devices, especially regarding to limits applicable within the ISM bands wherein this document allows unrestricted radiation.
NOTE 2 Radio beam wireless power transfer devices can generate significant electromagnetic energy. While this document does not include requirements for radio-frequency (RF) exposure, the user is warned to take appropriate measures to ensure testing personnel and other bystanders are not subjected to harmful levels of RF exposure from the product under test.
This PAS adopts the requirements from CISPR 11 and provides important clarifications on the application of CISPR 11 for RB-WPT.
- Technical specification18 pagesEnglish languagesale 15% off
The contents of the corrigendum 1 (2022-01) and the Interpretation sheet 1 (2025-04) (applying to the English version only), have been included in this copy.
- Standard2 pagesEnglish languagesale 15% off
IEC 60364-4-44:2024 provides requirements for the safety of electrical installations in the event of voltage disturbances and electromagnetic disturbances generated for different specified reasons. The requirements of this document are not intended to apply to systems for distribution of energy to the public, or power generation and transmission for such systems (see the scope of IEC 60364-1) although such disturbances can be conducted into or between electrical installations via these supply systems. This third edition cancels and replaces the second edition published in 2007, Amendment 1:2015 and Amendment 2:2018. This edition constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous edition:
a) the structure of the document has been updated in accordance with the ISO/IEC Directives, Part 2:2021: the terms, definitions and symbols have been regrouped under a new Subclause 440.3, the tables and figures have been renumbered;
b) Clause 443 has been amended to better introduce the DC SPD and to improve some of the wording.
- Standard116 pagesEnglish languagesale 15% off
CISPR TR 31: 2024, which is a Technical Report, covers the rationale behind the database containing the characteristics of radio services. The database is a "living document " in the format of a spreadsheet file in the EMC Zone of the IEC web site: https://www.iec.ch/emc/radio-services-database . As new input for the IEC Radio Services Database arrives, this Technical Report provides guidance and support for the systematic collation of data on those radio services which are relevant for determination of CISPR limits according to CISPR TR 16-4-4. All interested parties are invited to contribute with relevant data to the database, e.g., via the National Committees represented in CISPR/H. The objective of the database is to register those characteristics which are relevant for derivation and specification of limits for disturbances from electric and/or electronic equipment, systems and installations. Committees responsible for generic and/or product emission EMC standards use this information together with CISPR TR 16-4-4.
This third edition cancels and replaces the second edition published in 2012. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition:
a) A new Clause 3 covers a line of essential definitions of radio parameters, the knowledge of which is necessary to get qualified input data for inclusion of essential requirements in the present radio services database (RSD) maintained by CISPR and IEC.
b) The radio parameters and conditions of use of radio receivers listed in Table 1 of this edition of CISPR TR 31 are provided now with instructive advice in its new Subclauses 5.1 and 5.2, on selection of data for input to the RSD and retrieval of that data for consideration and use with the limits setting model as in CISPR TR 16-4-4 which was missing in the previous edition of CISPR TR 31.
c) Finally, another new informative Annex B informs, to the extent necessary, on the principles of ITU-R on determination of data for the minimum usable field strength (to be inserted in Column (E) of the RSD) and of the associated tolerable disturbance at the antenna of the radio reception system or other self-contained radio receiver (also to be used as input with the limits-setting model in CISPR TR 16-4-4), which concerns only parties who are concerned with designing and projecting of radio-communication/broadcast networks and with coverage planning of related radio services. Knowledge of these fundamental principles also by CISPR experts will ensure that only valid data will get future input to the RSD maintained by CISPR and IEC.
- Technical report17 pagesEnglish languagesale 15% off
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.
Loading comments...