IEC 60317-15:2004
(Main)Specifications for particular types of winding wires - Part 15: Polyesterimide enamelled round aluminium wire, class 180
Specifications for particular types of winding wires - Part 15: Polyesterimide enamelled round aluminium wire, class 180
Specifies the requirements of enamelled round aluminium winding wire of class 180 with a sole coating based on polyesterimide resin, which may be modified providing it retains the chemical identity of the original resin and meets all specified wire requirements. Class 180 is a thermal class that requires a minimum temperature index of 180 and a heat shock temperature of at least 200 °C. The temperature in degrees Celsius corresponding to the temperature index is not necessarily that at which it is recommended that the wire be operated and this will depend on many factors, including the type of equipment involved. The range of nominal conductor diameters covered by this standard is as follows: - grade 1: 0,400 mm up to and including 1,600 mm; - grade 2: 0,400 mm up to and including 5,000 mm. The nominal conductor diameters are specified in Clause 4 of IEC 60317-0-3. The main changes with respect to the previous edition are listed below: - new requirements for appearance, Subclause 3.2, added; - springiness test, Clause 7, determined to be inappropriate; - cut-through test, Clause 10, determined to be inappropriate; - high temperature failure test, Clause 22, deleted; - new pin hole test, Clause 23, added.
Spécifications pour types particuliers de fils de bobinage - Partie 15: Fil de section circulaire en aluminium émaillé avec polyesterimide, classe 180
Spécifie les exigences concernant les fils de bobinage de section circulaire en aluminium émaillé de classe 180 avec un revêtement unique à base de résine polyesterimide qui peut être modifiée pour autant que cette résine conserve l'identité chimique de la résine initiale et réponde à toutes les exigences du fil. La classe 180 est une classe thermique qui exige un indice de température minimal de 180 et une température de choc thermique d'au moins 200 °C. La température en degrés Celsius correspondant à l'indice de température n'est pas nécessairement celle à laquelle il est recommandé d'utiliser le fil; cela dépendra de beaucoup de facteurs, y compris du type d'équipement considéré. La gamme des diamètres nominaux des conducteurs couverte par la présente norme est la suivante: - grade 1: 0,400 mm jusque et y compris 1,600 mm; - grade 2: 0,400 mm jusque et y compris 5,000 mm. Les diamètres nominaux des conducteurs sont spécifiés dans l'Article 4 de la CEI 60317-0-3. Les modifications principales par rapport à l'édition précédente sont les suivantes: - nouvelles exigences pour les aspects, Paragraphe 3.2, ajouté; - essai sur l'effet de ressort, Article 7, déterminé comme étant non applicable; - essai de thermoplasticité, Article 10, déterminé comme étant non applicable; - essai de défaillance à haute température, Article 22, supprimé; - nouvel essai de détection des micro-fissures en immersion, Article 23, ajouté.
General Information
Relations
Overview
IEC 60317-15:2004 (consolidated with amendments to 2024) specifies requirements for polyesterimide enamelled round aluminium winding wire, thermal class 180. It applies to aluminium conductor wires with a sole polyesterimide-based enamel coating (modifications allowed if the chemical identity is retained) intended for electrical windings. The standard defines thermal performance (minimum temperature index 180 and heat shock ≥ 200 °C), dimensional ranges for two grades, test requirements and appearance criteria.
Key topics and requirements
- Scope and materials: Enamelled round aluminium wire with a single polyesterimide resin coating; modified resins permitted if they meet the wire requirements and retain chemical identity.
- Thermal class: Minimum temperature index 180; heat shock temperature at least 200 °C. The stated temperature index is a material rating, not a direct operating-temperature recommendation.
- Nominal conductor diameters:
- Grade 1: 0.400 mm up to and including 1.600 mm
- Grade 2: 0.400 mm up to and including 5.000 mm
(Specific diameters referenced to IEC 60317-0-3.)
- Mechanical & electrical tests: References to general test methods in IEC 60317‑0‑3 and IEC 60851 where applicable. Tests covered include dimensions, electrical resistance, elongation, flexibility/adherence and heat shock.
- Resistance to abrasion: Minimum force-to-failure values are specified in Table 1 for nominal diameters up to 2.500 mm (different values for Grade 1 and Grade 2; intermediate diameters use the next larger nominal value).
- Dielectric/bonding tests: Breakdown voltage (with elevated temperature 180 °C), continuity of insulation and the new pin hole test are included.
- Tests deemed inappropriate or deleted: springiness, cut-through, resistance to refrigerants, solderability, heat/solvent bonding, dielectric dissipation factor and loss of mass are listed as inappropriate or removed for this wire type. High temperature failure test (Clause 22) was deleted.
- Appearance & packaging: New appearance requirements added; packaging requirements retained.
Applications and users
This standard is intended for:
- Manufacturers of winding wire and enameled aluminium conductors
- Motor, transformer, generator and coil designers specifying wire for high‑temperature windings
- Quality control, test laboratories and procurement teams verifying conformity
- R&D and materials engineers selecting polyesterimide enamel systems for electrical applications
Practical uses include material selection, product specification, manufacturing QA, type testing and contract compliance for equipment requiring class 180 thermal performance.
Related standards
- IEC 60317-0-3 - General requirements for enamelled round aluminium wire (normative reference)
- IEC 60851 - Test methods for winding wires (referenced for specific test procedures)
Keywords: IEC 60317-15, polyesterimide enamelled round aluminium wire, class 180, winding wire, temperature index 180, heat shock 200 °C, resistance to abrasion, pin hole test, nominal conductor diameters.
Frequently Asked Questions
IEC 60317-15:2004 is a standard published by the International Electrotechnical Commission (IEC). Its full title is "Specifications for particular types of winding wires - Part 15: Polyesterimide enamelled round aluminium wire, class 180". This standard covers: Specifies the requirements of enamelled round aluminium winding wire of class 180 with a sole coating based on polyesterimide resin, which may be modified providing it retains the chemical identity of the original resin and meets all specified wire requirements. Class 180 is a thermal class that requires a minimum temperature index of 180 and a heat shock temperature of at least 200 °C. The temperature in degrees Celsius corresponding to the temperature index is not necessarily that at which it is recommended that the wire be operated and this will depend on many factors, including the type of equipment involved. The range of nominal conductor diameters covered by this standard is as follows: - grade 1: 0,400 mm up to and including 1,600 mm; - grade 2: 0,400 mm up to and including 5,000 mm. The nominal conductor diameters are specified in Clause 4 of IEC 60317-0-3. The main changes with respect to the previous edition are listed below: - new requirements for appearance, Subclause 3.2, added; - springiness test, Clause 7, determined to be inappropriate; - cut-through test, Clause 10, determined to be inappropriate; - high temperature failure test, Clause 22, deleted; - new pin hole test, Clause 23, added.
Specifies the requirements of enamelled round aluminium winding wire of class 180 with a sole coating based on polyesterimide resin, which may be modified providing it retains the chemical identity of the original resin and meets all specified wire requirements. Class 180 is a thermal class that requires a minimum temperature index of 180 and a heat shock temperature of at least 200 °C. The temperature in degrees Celsius corresponding to the temperature index is not necessarily that at which it is recommended that the wire be operated and this will depend on many factors, including the type of equipment involved. The range of nominal conductor diameters covered by this standard is as follows: - grade 1: 0,400 mm up to and including 1,600 mm; - grade 2: 0,400 mm up to and including 5,000 mm. The nominal conductor diameters are specified in Clause 4 of IEC 60317-0-3. The main changes with respect to the previous edition are listed below: - new requirements for appearance, Subclause 3.2, added; - springiness test, Clause 7, determined to be inappropriate; - cut-through test, Clause 10, determined to be inappropriate; - high temperature failure test, Clause 22, deleted; - new pin hole test, Clause 23, added.
IEC 60317-15:2004 is classified under the following ICS (International Classification for Standards) categories: 29.060.10 - Wires. The ICS classification helps identify the subject area and facilitates finding related standards.
IEC 60317-15:2004 has the following relationships with other standards: It is inter standard links to IEC 60317-15:2004/AMD1:2010, IEC 60317-15:2004/AMD2:2024, IEC 60317-15:1990/AMD1:1997. Understanding these relationships helps ensure you are using the most current and applicable version of the standard.
You can purchase IEC 60317-15:2004 directly from iTeh Standards. The document is available in PDF format and is delivered instantly after payment. Add the standard to your cart and complete the secure checkout process. iTeh Standards is an authorized distributor of IEC standards.
Standards Content (Sample)
IEC 60317-15 ®
Edition 3.2 2024-06
CONSOLIDATED VERSION
INTERNATIONAL
STANDARD
colour
inside
Specifications for particular types of winding wires –
Part 15: Polyesterimide enamelled round aluminium wire, class 180
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form
or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from
either IEC or IEC's member National Committee in the country of the requester. If you have any questions about IEC
copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or
your local IEC member National Committee for further information.
IEC Secretariat Tel.: +41 22 919 02 11
3, rue de Varembé info@iec.ch
CH-1211 Geneva 20 www.iec.ch
Switzerland
About the IEC
The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes
International Standards for all electrical, electronic and related technologies.
About IEC publications
The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the
latest edition, a corrigendum or an amendment might have been published.
IEC publications search - webstore.iec.ch/advsearchform IEC Products & Services Portal - products.iec.ch
The advanced search enables to find IEC publications by a Discover our powerful search engine and read freely all the
variety of criteria (reference number, text, technical publications previews, graphical symbols and the glossary.
committee, …). It also gives information on projects, replaced With a subscription you will always have access to up to date
and withdrawn publications. content tailored to your needs.
IEC Just Published - webstore.iec.ch/justpublished
Electropedia - www.electropedia.org
Stay up to date on all new IEC publications. Just Published
The world's leading online dictionary on electrotechnology,
details all new publications released. Available online and once
containing more than 22 500 terminological entries in English
a month by email.
and French, with equivalent terms in 25 additional languages.
Also known as the International Electrotechnical Vocabulary
IEC Customer Service Centre - webstore.iec.ch/csc
(IEV) online.
If you wish to give us your feedback on this publication or need
further assistance, please contact the Customer Service
Centre: sales@iec.ch.
IEC 60317-15 ®
Edition 3.2 2024-06
CONSOLIDATED VERSION
INTERNATIONAL
STANDARD
colour
inside
Specifications for particular types of winding wires –
Part 15: Polyesterimide enamelled round aluminium wire, class 180
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
ICS 29.060.10 ISBN 978-2-8322-9189-4
REDLINE VERSION – 2 – IEC 60317-15:2004+AMD1:2010
+AMD2:2024 © IEC 2024
CONTENTS
FOREWORD . 3
INTRODUCTION . 5
1 Scope . 6
2 Normative references . 6
3 Terms, definitions, general notes and appearance . 7
3.1 Terms and definitions . 7
3.2 General notes. 7
3.2.1 Methods of test . 7
3.2.2 Winding wire . 7
3.3 Appearance . 7
4 Dimensions . 7
5 Electrical resistance . 7
6 Elongation . 7
7 Springiness . 7
8 Flexibility and adherence . 8
9 Heat shock . 8
10 Cut-through . 8
11 Resistance to abrasion (nominal conductor diameters up to and including
2,500 mm) . 8
12 Resistance to solvents . 8
13 Breakdown voltage . 9
14 Continuity of insulation . 9
15 Temperature index . 9
16 Resistance to refrigerants . 9
17 Solderability . 9
18 Heat or solvent bonding . 9
19 Dielectric dissipation factor . 9
20 Resistance to transformer oil . 9
21 Loss of mass . 9
23 Pin hole test . 9
30 Packaging . 9
Table 1 – Résistance to abrasion . 8
+AMD2:2024 © IEC 2024
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
SPECIFICATIONS FOR PARTICULAR TYPES
OF WINDING WIRES –
Part 15: Polyesterimide enamelled round aluminium wire,
class 180
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) IEC draws attention to the possibility that the implementation of this document may involve the use of (a)
patent(s). IEC takes no position concerning the evidence, validity or applicability of any claimed patent rights in
respect thereof. As of the date of publication of this document, IEC had not received notice of (a) patent(s),
which may be required to implement this document. However, implementers are cautioned that this may not
represent the latest information, which may be obtained from the patent database available at
https://patents.iec.ch. IEC shall not be held responsible for identifying any or all such patent rights.
This consolidated version of the official IEC Standard and its amendments has been
prepared for user convenience.
IEC 60317-15 edition 3.2 contains the third edition (2004-08) [documents 55/908/FDIS
and 55/914/RVD], its amendment 1 (2010-06) [documents 55/1121/CDV and 55/1149/RVC]
and its amendment 2 (2024-06) [documents 55/1984/CDV and 55/2020/RVC].
In this Redline version, a vertical line in the margin shows where the technical content
is modified by amendments 1 and 2. Additions are in green text, deletions are in
strikethrough red text. A separate Final version with all changes accepted is available
in this publication.
REDLINE VERSION – 4 – IEC 60317-15:2004+AMD1:2010
+AMD2:2024 © IEC 2024
International Standard IEC 60317-15 has been prepared by IEC technical committee 55:
Winding wires.
This third edition of IEC 60317-15 cancels and replaces the second edition published in
1990 and amendment 1 (1997). This edition constitutes a technical revision.
The main changes with respect to the previous edition are listed below:
– new requirements for appearance, Subclause 3.2, added;
– springiness test, Clause 7, determined to be inappropriate;
– cut-through test, Clause 10, determined to be inappropriate;
– high temperature failure test, Clause 22, deleted;
– new pin hole test, Clause 23, added.
This International Standard is to be read in conjunction with IEC 60317-0-3.
This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.
The committee has decided that the contents of this document and its amendments will
remain unchanged until the stability date indicated on the IEC website under webstore.iec.ch
in the data related to the specific document. At this date, the document will be
• reconfirmed,
• withdrawn, or
• revised.
IMPORTANT – The 'colour inside' logo on the cover page of this publication indicates
that it contains colours which are considered to be useful for the correct
understanding of its contents. Users should therefore print this document using a
colour printer.
+AMD2:2024 © IEC 2024
INTRODUCTION
This part of IEC 60317 is one of a series which deals with insulated wires used for windings in
electrical equipment. The series has three groups describing
1) winding wires – Test methods (IEC 60851);
2) specifications for particular types of winding wires (IEC 60317);
3) packaging of winding wires (IEC 60264).
REDLINE VERSION – 6 – IEC 60317-15:2004+AMD1:2010
+AMD2:2024 © IEC 2024
SPECIFICATIONS FOR PARTICULAR TYPES
OF WINDING WIRES –
Part 15: Polyesterimide enamelled round aluminium wire,
class 180
1 Scope
This part of IEC 60317 specifies the requirements of enamelled round aluminium winding wire
of class 180 with a sole coating based on polyesterimide resin, which may be modified
providing it retains the chemical identity of the original resin and meets all specified wire
requirements.
NOTE A modified resin is a resin that has undergone a chemical change, or contains one or more additives to
enhance certain performance or application characteristics.
Class 180 is a thermal class that requires a minimum temperature index of 180 and a heat
shock temperature of at least 200 °C.
The temperature in degrees Celsius corresponding to the temperature index is not necessarily
that at which it is recommended that the wire be operated and this will depend on many
factors, including the type of equipment involved.
The range of nominal conductor diameters covered by this standard is as follows:
– grade 1: 0,400 mm up to and including 1,600 mm;
– grade 2: 0,400 mm up to and including 5,000 mm.
The nominal conductor diameters are specified in Clause 4 of IEC 60317-0-3.
2 Normative references
The following referenced documents are indispensable for referred to in the application text in
such a way that some or all of their content constitutes requirements of this document. For
dated references, only the edition cited applies. For undated references, the latest edition of
the referenced document (including any amendments) applies.
IEC 60317-0-3 :2008, Specifications for particular types of winding wires – Part 0-3: General
requirements – Enamelled round aluminium wire
IEC 60317-0-3:2008/AMD1:2013
IEC 60317-0-3:2008/AMD2:2019
3 Definitions and general notes on methods of test and appearance
3.1 Definitions and general notes on methods of test
For definitions and general notes on methods of test, see Clause 3 of IEC 60317-0-3.
In case of inconsistencies between IEC 60317-0-3 and this standard, IEC 60317-15 shall
prevail.
___________
There exists a consolidated edition 3.2:2019 that includes IEC 60317-0-3:2008, its Amendment 1:2013 and its
Amendment 2:2019.
+AMD2:2024 © IEC 2024
3.2 Appearance
See Clause 3 of IEC 60317-0-3.
3 Terms, definitions, general notes and appearance
3.1 Terms and definitions
For the purposes of this document, the terms and definitions given in IEC 60317-0-3 apply.
ISO and IEC maintain terminology databases for use in standardization at the following
addresses:
• IEC Electropedia: available at https://www.electropedia.org/
• ISO Online browsing platform: available at https://www.iso.org/obp
3.2 General notes
3.2.1 Methods of test
Subclause 3.2.1 of IEC 60317-0-3:2008/AMD1:2013 and IEC 60317-0-3:2008/AMD2:2019
applies.
In case of inconsistencies between IEC 60317-0-3 and this document, IEC 60317-15 shall
prevail.
3.2.2 Winding wire
Subclause 3.2.2 of IEC 60317-0-3:2008/AMD1:2013 applies.
3.3 Appearance
Subclause 3.3 of IEC 60317-0-3:2008 applies.
4 Dimensions
See Clause 4 of IEC 60317-0-3.
5 Electrical resistance
See Clause 5 of IEC 60317-0-3.
Clause 5 of IEC 60317-0-3:2008 and IEC 60317-0-3:2008/AMD2:2019 applies.
6 Elongation
See Clause 6 of IEC 60317-0-3.
7 Springiness
Test inappropriate.
REDLINE VERSION – 8 – IEC 60317-15:2004+AMD1:2010
+AMD2:2024 © IEC 2024
8 Flexibility and adherence
See Clause 8 of IEC 60317-0-3.
9 Heat shock
See Clause 9 of IEC 60317-0-3, where the minimum heat shock temperature shall be 200 °C.
10 Cut-through
Test inappropriate.
11 Resistance to abrasio
...
NORME CEI
INTERNATIONALE IEC
60317-15
INTERNATIONAL
Troisième édition
STANDARD
Third edition
2004-08
Spécifications pour types particuliers
de fils de bobinage –
Partie 15:
Fil de section circulaire en aluminium émaillé
avec polyesterimide, classe 180
Specifications for particular types
of winding wires –
Part 15:
Polyesterimide enamelled round
aluminium wire, class 180
Numéro de référence
Reference number
CEI/IEC 60317-15:2004
Numérotation des publications Publication numbering
Depuis le 1er janvier 1997, les publications de la CEI As from 1 January 1997 all IEC publications are
sont numérotées à partir de 60000. Ainsi, la CEI 34-1 issued with a designation in the 60000 series. For
devient la CEI 60034-1. example, IEC 34-1 is now referred to as IEC 60034-1.
Editions consolidées Consolidated editions
Les versions consolidées de certaines publications de la The IEC is now publishing consolidated versions of its
CEI incorporant les amendements sont disponibles. Par publications. For example, edition numbers 1.0, 1.1
exemple, les numéros d’édition 1.0, 1.1 et 1.2 indiquent and 1.2 refer, respectively, to the base publication,
respectivement la publication de base, la publication de the base publication incorporating amendment 1 and
base incorporant l’amendement 1, et la publication de the base publication incorporating amendments 1
base incorporant les amendements 1 et 2. and 2.
Informations supplémentaires Further information on IEC publications
sur les publications de la CEI
Le contenu technique des publications de la CEI est The technical content of IEC publications is kept
constamment revu par la CEI afin qu'il reflète l'état under constant review by the IEC, thus ensuring that
actuel de la technique. Des renseignements relatifs à the content reflects current technology. Information
cette publication, y compris sa validité, sont dispo- relating to this publication, including its validity, is
nibles dans le Catalogue des publications de la CEI available in the IEC Catalogue of publications
(voir ci-dessous) en plus des nouvelles éditions, (see below) in addition to new editions, amendments
amendements et corrigenda. Des informations sur les and corrigenda. Information on the subjects under
sujets à l’étude et l’avancement des travaux entrepris consideration and work in progress undertaken by the
par le comité d’études qui a élaboré cette publication, technical committee which has prepared this
ainsi que la liste des publications parues, sont publication, as well as the list of publications issued,
également disponibles par l’intermédiaire de: is also available from the following:
• Site web de la CEI (www.iec.ch) • IEC Web Site (www.iec.ch)
• Catalogue des publications de la CEI • Catalogue of IEC publications
Le catalogue en ligne sur le site web de la CEI The on-line catalogue on the IEC web site
(www.iec.ch/searchpub) vous permet de faire des (www.iec.ch/searchpub) enables you to search by a
recherches en utilisant de nombreux critères, variety of criteria including text searches,
comprenant des recherches textuelles, par comité technical committees and date of publication. On-
d’études ou date de publication. Des informations en line information is also available on recently
ligne sont également disponibles sur les nouvelles issued publications, withdrawn and replaced
publications, les publications remplacées ou retirées, publications, as well as corrigenda.
ainsi que sur les corrigenda.
• IEC Just Published • IEC Just Published
Ce résumé des dernières publications parues This summary of recently issued publications
(www.iec.ch/online_news/justpub) est aussi dispo- (www.iec.ch/online_news/justpub) is also available
nible par courrier électronique. Veuillez prendre by email. Please contact the Customer Service
contact avec le Service client (voir ci-dessous) Centre (see below) for further information.
pour plus d’informations.
• Service clients • Customer Service Centre
Si vous avez des questions au sujet de cette If you have any questions regarding this
publication ou avez besoin de renseignements publication or need further assistance, please
supplémentaires, prenez contact avec le Service contact the Customer Service Centre:
clients:
Email: custserv@iec.ch Email: custserv@iec.ch
Tél: +41 22 919 02 11 Tel: +41 22 919 02 11
Fax: +41 22 919 03 00 Fax: +41 22 919 03 00
.
NORME CEI
INTERNATIONALE IEC
60317-15
INTERNATIONAL
Troisième édition
STANDARD
Third edition
2004-08
Spécifications pour types particuliers
de fils de bobinage –
Partie 15:
Fil de section circulaire en aluminium émaillé
avec polyesterimide, classe 180
Specifications for particular types
of winding wires –
Part 15:
Polyesterimide enamelled round
aluminium wire, class 180
” IEC 2004 Droits de reproduction réservés Copyright - all rights reserved
Aucune partie de cette publication ne peut être reproduite ni No part of this publication may be reproduced or utilized in any
utilisée sous quelque forme que ce soit et par aucun procédé, form or by any means, electronic or mechanical, including
électronique ou mécanique, y compris la photocopie et les photocopying and microfilm, without permission in writing from
microfilms, sans l'accord écrit de l'éditeur. the publisher.
International Electrotechnical Commission, 3, rue de Varembé, PO Box 131, CH-1211 Geneva 20, Switzerland
Telephone: +41 22 919 02 11 Telefax: +41 22 919 03 00 E-mail: inmail@iec.ch Web: www.iec.ch
CODE PRIX
Commission Electrotechnique Internationale PRICE CODE J
International Electrotechnical Commission
ɆɟɠɞɭɧɚɪɨɞɧɚɹɗɥɟɤɬɪɨɬɟɯɧɢɱɟɫɤɚɹɄɨɦɢɫɫɢɹ
Pour prix, voir catalogue en vigueur
For price, see current catalogue
– 2 – 60317-15 © CEI:2004
SOMMAIRE
AVANT-PROPOS.4
INTRODUCTION.8
1 Domaine d'application.10
2 Références normatives .10
3 Définitions et notes générales concernant les méthodes d'essais et aspects .10
3.1 Définitions et notes générales concernant les méthodes d'essais.10
3.2 Aspects .12
4 Dimensions .12
5 Résistance électrique .12
6 Allongement .12
7 Effet de ressort.12
8 Souplesse et adhérence .12
9 Choc thermique .12
10 Thermoplasticité .12
11 Résistance à l'abrasion (diamètres nominaux des conducteurs inférieurs ou
égaux à 2,500 mm) .12
12 Résistance aux solvants .14
13 Tension de claquage .14
14 Continuité de l'isolant .14
15 Indice de température.14
16 Résistance aux réfrigérants .14
17 Brasabilité .16
18 Adhérence par chaleur ou par solvant .16
19 Facteur de dissipation diélectrique.16
20 Résistance à l'huile de transformateur.16
21 Perte de masse .16
23 Détection des micro-fissures en immersion .16
30 Conditionnement .16
Tableau 1 – Résistance à l'abrasion .14
60317-15 © IEC:2004 – 3 –
CONTENTS
FOREWORD.5
INTRODUCTION.9
1 Scope .11
2 Normative references .11
3 Definitions and general notes on methods of test and appearance .11
3.1 Definitions and general notes on methods of test.11
3.2 Appearance.13
4 Dimensions .13
5 Electrical resistance .13
6 Elongation.13
7 Springiness .13
8 Flexibility and adherence .13
9 Heat shock .13
10 Cut-through .13
11 Resistance to abrasion (nominal conductor diameters up to and including 2,500 mm) .13
12 Resistance to solvents.15
13 Breakdown voltage .15
14 Continuity of insulation .15
15 Temperature index .15
16 Resistance to refrigerants .15
17 Solderability .17
18 Heat or solvent bonding .17
19 Dielectric dissipation factor .17
20 Resistance to transformer oil .17
21 Loss of mass .17
23 Pin hole test .17
30 Packaging .17
Table 1 – Résistance to abrasion .15
– 4 – 60317-15 © CEI:2004
COMMISSION ÉLECTROTECHNIQUE INTERNATIONALE
____________
SPÉCIFICATIONS POUR TYPES PARTICULIERS
DE FILS DE BOBINAGE –
Partie 15: Fil de section circulaire en aluminium émaillé
avec polyesterimide, classe 180
AVANT-PROPOS
1) La Commission Electrotechnique Internationale (CEI) est une organisation mondiale de normalisation
composée de l'ensemble des comités électrotechniques nationaux (Comités nationaux de la CEI). La CEI a
pour objet de favoriser la coopération internationale pour toutes les questions de normalisation dans les
domaines de l'électricité et de l'électronique. A cet effet, la CEI – entre autres activités – publie des Normes
internationales, des Spécifications techniques, des Rapports techniques, des Spécifications accessibles au
public (PAS) et des Guides (ci-après dénommés "Publication(s) de la CEI"). Leur élaboration est confiée à des
comités d'études, aux travaux desquels tout Comité national intéressé par le sujet traité peut participer. Les
organisations internationales, gouvernementales et non gouvernementales, en liaison avec la CEI, participent
également aux travaux. La CEI collabore étroitement avec l'Organisation Internationale de Normalisation (ISO),
selon des conditions fixées par accord entre les deux organisations.
2) Les décisions ou accords officiels de la CEI concernant les questions techniques représentent, dans la mesure
du possible, un accord international sur les sujets étudiés, étant donné que les Comités nationaux de la CEI
intéressés sont représentés dans chaque comité d’études.
3) Les Publications de la CEI se présentent sous la forme de recommandations internationales et sont agréées
comme telles par les Comités nationaux de la CEI. Tous les efforts raisonnables sont entrepris afin que la CEI
s'assure de l'exactitude du contenu technique de ses publications; la CEI ne peut pas être tenue responsable
de l'éventuelle mauvaise utilisation ou interprétation qui en est faite par un quelconque utilisateur final.
4) Dans le but d'encourager l'uniformité internationale, les Comités nationaux de la CEI s'engagent, dans toute la
mesure possible, à appliquer de façon transparente les Publications de la CEI dans leurs publications
nationales et régionales. Toutes divergences entre toutes Publications de la CEI et toutes publications
nationales ou régionales correspondantes doivent être indiquées en termes clairs dans ces dernières.
5) La CEI n’a prévu aucune procédure de marquage valant indication d’approbation et n'engage pas sa
responsabilité pour les équipements déclarés conformes à une de ses Publications.
6) Tous les utilisateurs doivent s'assurer qu'ils sont en possession de la dernière édition de cette publication.
7) Aucune responsabilité ne doit être imputée à la CEI, à ses administrateurs, employés, auxiliaires ou
mandataires, y compris ses experts particuliers et les membres de ses comités d'études et des Comités
nationaux de la CEI, pour tout préjudice causé en cas de dommages corporels et matériels, ou de tout autre
dommage de quelque nature que ce soit, directe ou indirecte, ou pour supporter les coûts (y compris les frais
de justice) et les dépenses découlant de la publication ou de l'utilisation de cette Publication de la CEI ou de
toute autre Publication de la CEI, ou au crédit qui lui est accordé.
8) L'attention est attirée sur les références normatives citées dans cette publication. L'utilisation de publications
référencées est obligatoire pour une application correcte de la présente publication.
9) L’attention est attirée sur le fait que certains des éléments de la présente Publication de la CEI peuvent faire
l’objet de droits de propriété intellectuelle ou de droits analogues. La CEI ne saurait être tenue pour
responsable de ne pas avoir identifié de tels droits de propriété et de ne pas avoir signalé leur existence.
La Norme internationale CEI 60317-15 a été établie par le com
...
IEC 60317-15 ®
Edition 3.1 2010-06
CONSOLIDATED VERSION
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
colour
inside
Specifications for particular types of winding wires –
Part 15: Polyesterimide enamelled round aluminium wire, class 180
Spécifications pour types particuliers de fils de bobinage –
Partie 15: Fil de section circulaire en aluminium émaillé avec polyesterimide,
classe 180
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form
or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from
either IEC or IEC's member National Committee in the country of the requester. If you have any questions about IEC
copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or
your local IEC member National Committee for further information.
Droits de reproduction réservés. Sauf indication contraire, aucune partie de cette publication ne peut être reproduite
ni utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie
et les microfilms, sans l'accord écrit de l'IEC ou du Comité national de l'IEC du pays du demandeur. Si vous avez des
questions sur le copyright de l'IEC ou si vous désirez obtenir des droits supplémentaires sur cette publication, utilisez
les coordonnées ci-après ou contactez le Comité national de l'IEC de votre pays de résidence.
IEC Central Office Tel.: +41 22 919 02 11
3, rue de Varembé Fax: +41 22 919 03 00
CH-1211 Geneva 20 info@iec.ch
Switzerland www.iec.ch
About the IEC
The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes
International Standards for all electrical, electronic and related technologies.
About IEC publications
The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the
latest edition, a corrigenda or an amendment might have been published.
IEC Catalogue - webstore.iec.ch/catalogue Electropedia - www.electropedia.org
The stand-alone application for consulting the entire The world's leading online dictionary of electronic and
bibliographical information on IEC International Standards, electrical terms containing 20 000 terms and definitions in
Technical Specifications, Technical Reports and other English and French, with equivalent terms in 15 additional
documents. Available for PC, Mac OS, Android Tablets and languages. Also known as the International Electrotechnical
iPad. Vocabulary (IEV) online.
IEC publications search - www.iec.ch/searchpub IEC Glossary - std.iec.ch/glossary
The advanced search enables to find IEC publications by a 65 000 electrotechnical terminology entries in English and
variety of criteria (reference number, text, technical French extracted from the Terms and Definitions clause of
committee,…). It also gives information on projects, replaced IEC publications issued since 2002. Some entries have been
and withdrawn publications. collected from earlier publications of IEC TC 37, 77, 86 and
CISPR.
IEC Just Published - webstore.iec.ch/justpublished
Stay up to date on all new IEC publications. Just Published IEC Customer Service Centre - webstore.iec.ch/csc
details all new publications released. Available online and If you wish to give us your feedback on this publication or
also once a month by email. need further assistance, please contact the Customer Service
Centre: csc@iec.ch.
A propos de l'IEC
La Commission Electrotechnique Internationale (IEC) est la première organisation mondiale qui élabore et publie des
Normes internationales pour tout ce qui a trait à l'électricité, à l'électronique et aux technologies apparentées.
A propos des publications IEC
Le contenu technique des publications IEC est constamment revu. Veuillez vous assurer que vous possédez l’édition la
plus récente, un corrigendum ou amendement peut avoir été publié.
Catalogue IEC - webstore.iec.ch/catalogue Electropedia - www.electropedia.org
Application autonome pour consulter tous les renseignements
Le premier dictionnaire en ligne de termes électroniques et
bibliographiques sur les Normes internationales,
électriques. Il contient 20 000 termes et définitions en anglais
Spécifications techniques, Rapports techniques et autres
et en français, ainsi que les termes équivalents dans 15
documents de l'IEC. Disponible pour PC, Mac OS, tablettes
langues additionnelles. Egalement appelé Vocabulaire
Android et iPad.
Electrotechnique International (IEV) en ligne.
Recherche de publications IEC - www.iec.ch/searchpub
Glossaire IEC - std.iec.ch/glossary
La recherche avancée permet de trouver des publications IEC
65 000 entrées terminologiques électrotechniques, en anglais
en utilisant différents critères (numéro de référence, texte,
et en français, extraites des articles Termes et Définitions des
comité d’études,…). Elle donne aussi des informations sur les
publications IEC parues depuis 2002. Plus certaines entrées
projets et les publications remplacées ou retirées.
antérieures extraites des publications des CE 37, 77, 86 et
CISPR de l'IEC.
IEC Just Published - webstore.iec.ch/justpublished
Restez informé sur les nouvelles publications IEC. Just Service Clients - webstore.iec.ch/csc
Published détaille les nouvelles publications parues. Si vous désirez nous donner des commentaires sur cette
Disponible en ligne et aussi une fois par mois par email. publication ou si vous avez des questions contactez-nous:
csc@iec.ch.
IEC 60317-15 ®
Edition 3.1 2010-06
CONSOLIDATED VERSION
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
colour
inside
Specifications for particular types of winding wires –
Part 15: Polyesterimide enamelled round aluminium wire, class 180
Spécifications pour types particuliers de fils de bobinage –
Partie 15: Fil de section circulaire en aluminium émaillé avec polyesterimide,
classe 180
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 29.060.10 ISBN 978-2-8891-0952-4
– 2 – 60317-15 © IEC:2004+A1:2010
CONTENTS
FOREWORD.3
INTRODUCTION.5
1 Scope.6
2 Normative references .6
3 Definitions and general notes on methods of test and appearance.7
3.1 Definitions and general notes on methods of test .7
3.2 Appearance.7
4 Dimensions .7
5 Electrical resistance .7
6 Elongation .7
7 Springiness .7
8 Flexibility and adherence.7
9 Heat shock .7
10 Cut-through .7
11 Resistance to abrasion (nominal conductor diameters up to and including 2,500 mm) .7
12 Resistance to solvents.8
13 Breakdown voltage .8
14 Continuity of insulation .8
15 Temperature index .8
16 Resistance to refrigerants.8
17 Solderability .9
18 Heat or solvent bonding.9
19 Dielectric dissipation factor.9
20 Resistance to transformer oil .9
21 Loss of mass .9
23 Pin hole test .9
30 Packaging .9
Table 1 – Résistance to abrasion.8
60317-15 © IEC:2004+A1:2010 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
SPECIFICATIONS FOR PARTICULAR TYPES
OF WINDING WIRES –
Part 15: Polyesterimide enamelled round aluminium wire,
class 180
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
This consolidated version of the official IEC Standard and its amendment has been
prepared for user convenience.
IEC 60317-15 edition 3.1 contains the third edition (2004) [documents 55/908/FDIS and
55/914/RVD] and its amendment 1 (2010) [documents 55/1121/CDV and 55/1149/RVC].
A vertical line in the margin shows where the base publication has been modified by
amendment 1. Additions and deletions are displayed in red, with deletions being struck
through.
– 4 – 60317-15 © IEC:2004+A1:2010
International Standard IEC 60317-15 has been prepared by IEC technical committee 55:
Winding wires.
The main changes with respect to the previous edition are listed below:
– new requirements for appearance, Subclause 3.2, added;
– springiness test, Clause 7, determined to be inappropriate;
– cut-through test, Clause 10, determined to be inappropriate;
– high temperature failure test, Clause 22, deleted;
– new pin hole test, Clause 23, added.
This International Standard is to be read in conjunction with IEC 60317-0-3.
This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.
The committee has decided that the contents of the base publication and its amendments will
remain unchanged until the stability date indicated on the IEC web site under
"http://webstore.iec.ch" in the data related to the specific publication. At this date, the
publication will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
IMPORTANT – The “colour inside” logo on the cover page of this publication indicates
that it contains colours which are considered to be useful for the correct understanding
of its contents. Users should therefore print this publication using a colour printer.
60317-15 © IEC:2004+A1:2010 – 5 –
INTRODUCTION
This part of IEC 60317 is one of a series which deals with insulated wires used for windings in
electrical equipment. The series has three groups describing
1) winding wires – Test methods (IEC 60851);
2) specifications for particular types of winding wires (IEC 60317);
3) packaging of winding wires (IEC 60264).
– 6 – 60317-15 © IEC:2004+A1:2010
SPECIFICATIONS FOR PARTICULAR TYPES
OF WINDING WIRES –
Part 15: Polyesterimide enamelled round aluminium wire,
class 180
1 Scope
This part of IEC 60317 specifies the requirements of enamelled round aluminium winding wire
of class 180 with a sole coating based on polyesterimide resin, which may be modified
providing it retains the chemical identity of the original resin and meets all specified wire
requirements.
NOTE A modified resin is a resin that has undergone a chemical change, or contains one or more additives to
enhance certain performance or application characteristics.
Class 180 is a thermal class that requires a minimum temperature index of 180 and a heat
shock temperature of at least 200 °C.
The temperature in degrees Celsius corresponding to the temperature index is not necessarily
that at which it is recommended that the wire be operated and this will depend on many
factors, including the type of equipment involved.
The range of nominal conductor diameters covered by this standard is as follows:
– grade 1: 0,400 mm up to and including 1,600 mm;
– grade 2: 0,400 mm up to and including 5,000 mm.
The nominal conductor diameters are specified in Clause 4 of IEC 60317-0-3.
2 Normative references
The following referenced documents are indispensable for the application of this document.
For dated references, only the edition cited applies. For undated references, the latest edition
of the referenced document (including any amendments) applies.
IEC 60317-0-3, Specifications for particular types of winding wires – Part 0: General require-
ments – Section 3: Enamelled round aluminium wire
Amendment 1 (1999)
Amendment 2
IEC 60317-0-3:2008, Specifications for particular types of winding wires – Part 0-3: General
requirements – Enamelled round aluminium wire
IEC 60851-4:1996, Winding wires – Test methods – Part 4: Chemical properties
Amendment 1 (1997)
Amendment 2 (2005)
___________
To be published.
60317-15 © IEC:2004+A1:2010 – 7 –
3 Definitions and general notes on methods of test and appearance
3.1 Definitions and general notes on methods of test
For definitions and general notes on methods of test, see Clause 3 of IEC 60317-0-3.
In case of inconsistencies between IEC
...
La norme IEC 60317-15:2004 se concentre sur les exigences spécifiques des fils d'enroulement en aluminium rond émaillé de classe 180, utilisant un revêtement à base de résine polyesterimide. La portée de cette norme est essentielle pour les fabricants et utilisateurs de fils d'enroulement, car elle définit clairement les caractéristiques techniques requises pour garantir la performance et la durabilité des fils conçus pour des applications à haute température. L'un des points forts de cette norme est sa classification thermique claire. La classe 180 impose un indice de température minimale de 180 °C, essentiel pour des applications où la chaleur peut être un facteur limitant. De plus, la norme précise que les températures peuvent varier en fonction des équipements utilisés, facilitant ainsi son adaptation à divers contextes techniques. La norme couvre une gamme de diamètres de conducteurs nominale bien définie, allant de 0,400 mm à 5,000 mm, ce qui permet de répondre aux besoins variés des industries. Les modifications apportées par rapport à l'édition précédente, telles que l'ajout de nouveaux tests pour l'apparence et les tests de pin hole, renforcent la pertinence de la norme en garantissant des contrôles de qualité supplémentaires. Les ajustements effectués, comme la suppression des tests jugés inappropriés, témoignent d'une approche pragmatique qui vise à simplifier le processus de certification tout en maintenant des standards élevés. Cela assure aux utilisateurs que les fils d'enroulement respectent non seulement les exigences de performance, mais également les attentes visuelles et fonctionnelles. En résumé, la norme IEC 60317-15:2004 est d'une grande pertinence dans le domaine des fils d'enroulement en aluminium pour des applications exigeantes, alliant rigueur technique et adaptabilité, ce qui en fait un document indispensable pour les professionnels du secteur.
IEC 60317-15:2004 표준은 클래스 180에 해당하는 폴리에스터이미드 에나멜 도금 원형 알루미늄 와이어의 요구 사항을 명확히 규정하고 있습니다. 이 표준의 범위는 폴리에스터이미드 수지 기반의 단일 코팅 와이어에 국한되며, 원래 수지의 화학적 정체성을 유지하고 모든 요구 사항을 충족해야 합니다. 특히, 클래스 180은 최소 온도 지수 180과 최소 200 °C의 열충격 온도를 요구하여 내열성이 중요한 전기 기계 및 변압기와 같은 응용 분야에서 필수적인 기준이 됩니다. 이 표준의 강점 중 하나는 명확한 규격을 제공하여 제조업체와 사용자가 와이어의 성능을 정확히 이해하고 평가할 수 있도록 돕는 점입니다. 나노미터 단위의 전도체 직경 범위는 매우 다양하여 사용자의 필요에 맞춘 다양한 선택이 가능함을 보여줍니다. 또한, IEC 60317-15:2004의 개정된 버전에서는 외관 요건과 새로운 핀홀 테스트가 추가되는 등 최신 기술과 시제품의 요구 사항을 반영하고 있습니다. 또한, 이전 판과 비교해 본 표준의 주요 변경 사항은 쾌적성 테스트와 절단 테스트가 부적절하다고 판단되어 삭제된 점이며, 이는 사용자로 하여금 보다 실용적이고 신뢰성 있는 제품을 확보하는 데 기여합니다. 이러한 강력한 규정은 전송 용량 및 절연성능의 향상을 위해 중요한 기초가 됩니다. 결론적으로, IEC 60317-15:2004 표준은 특수한 와이어의 사양을 확립함으로써 고온 응용 분야에서의 신뢰성을 보장하고, 제조업체 및 사용자가 품질 있는 제품을 선택할 수 있도록 방향성을 제시하고 있습니다. 이는 전 산업 분야에 걸쳐 알루미늄 와이어의 활용도를 높이고, 보다 안전하고 효율적인 전기 기계의 발전에 기여하는 중요한 표준이라 할 수 있습니다.
Die Norm IEC 60317-15:2004 befasst sich mit den spezifischen Anforderungen an emaillierte runde Aluminiumwickeldrähte der Klasse 180, die eine Beschichtung auf Basis von Polyesterimidharz aufweisen. Diese Norm ist von entscheidender Bedeutung, da sie wesentliche Anforderungen definiert, die für den Einsatz in verschiedenen elektrischen Anwendungen unerlässlich sind. Ein herausragendes Merkmal dieser Norm ist die klare Definition der thermischen Klasse 180. Dies bedeutet, dass der Draht eine Mindesttemperaturindex von 180°C aufweisen muss, was für Anwendungen von hoher thermischer Belastung besonders vorteilhaft ist. Die Norm legt auch die Hitze-Schock-Temperatur von mindestens 200°C fest, was die Zuverlässigkeit und Langlebigkeit des Materials in anspruchsvollen Umgebungen erhöht. Die Norm deckt eine breite Palette von nennbaren Leiterdurchmessern ab, was ihre Flexibilität und Anpassungsfähigkeit an verschiedene Anwendungen unterstreicht. Mit den angegebenen Größen von 0,400 mm bis 1,600 mm für Grad 1 und bis zu 5,000 mm für Grad 2, können Hersteller sicherstellen, dass sie die richtigen Produkte für spezifische Bedürfnisse liefern können. Ein weiterer wichtiger Aspekt der Norm sind die Aktualisierungen gegenüber der vorherigen Ausgabe. Die Einführung neuer Anforderungen für das Erscheinungsbild, die in Unterabschnitt 3.2 geregelt sind, verbessert die Qualitätskontrolle und die Verarbeitung von Wickeldrähten. Zudem wurde der Federungs-Test sowie der Durchschlag-Test als unangemessen eingestuft, während ein neuer Pin-Hole-Test (Unterabschnitt 23) hinzugefügt wurde. Diese Änderungen zeigen das Engagement der Norm, sich an die modernsten industriellen Standards und Bedürfnisse anzupassen. Zusammenfassend lässt sich sagen, dass die IEC 60317-15:2004 eine wichtige und relevante Norm im Bereich der Wickeldrähte ist, die hohe Anforderungen an Leistung und Qualität stellt. Ihre spezifischen Spezifikationen und die Aktualisierungen machen sie zu einem unverzichtbaren Dokument für Hersteller und Anwender im Bereich elektrischer Wicklungen.
IEC 60317-15:2004は、特定の種類の巻線用ワイヤの仕様を定めた重要な標準文書であり、主にポリエステルイミドエナメル層を有するアルミニウムワイヤ（クラス180）に焦点を当てています。この標準は、エナメル加工された円形アルミニウム巻線ワイヤの要求事項を詳細に規定しており、特に180度の温度インデックスを持ち、最低200度の熱衝撃温度を要求するクラス180に該当します。この温度範囲は、使用する装置の種類など多くの要因に依存する旨も明記されています。 標準の適用範囲は、0.400 mmから5.000 mmまでの公称導体直径をカバーしており、技術者やエンジニアにとって非常に有用な指針となっています。また、この標準の新たに追加された要件により、外観の基準が明確化されており、クオリティ管理の向上に寄与しています。 さらに、データによると、前回の版からの主な変更点として、スプリングネス試験やカットスルー試験が不適切とされ削除され、新たにピンホール試験が追加されるなど、品質保証のための最新の知見が適用されています。これにより、使用者は新たな試験方法に基づいた製品評価が可能になり、より高い信頼性を持つワイヤを選定することができます。 IEC 60317-15:2004は、技術の進化に対応し、製品のパフォーマンスを向上させるための基準として、その関連性と重要性を高めています。具体的な要求事項を明確にすることで、ユーザーはより適切な材料選定を行うことができ、結果として電気機器の信頼性や効率性を向上させることが期待されます。
IEC 60317-15:2004 provides a comprehensive framework for the specifications of polyesterimide enamelled round aluminium winding wire, classified under class 180. This standard is critical for manufacturers and users as it delineates clear requirements and guidelines that this specific type of winding wire must adhere to. The scope of this standard is notably focused on the composition and thermal performance of wires that are solely coated with polyesterimide resin, ensuring that any modifications to the resin maintain its chemical integrity while fulfilling all specified wire requirements. The classification of class 180 implies stringent thermal performance, mandating a minimum temperature index of 180 °C and high heat shock resistance of at least 200 °C. This thermal reliability is essential for applications in various electrical and electronic equipment, making this standard highly relevant in sectors where performance and safety are paramount. Strengths of IEC 60317-15:2004 lie in its detailed specifications regarding the nominal conductor diameters, which are categorized into grade 1 and grade 2, facilitating a clear understanding for manufacturers concerning the allowable dimensions from 0.400 mm to 5.000 mm. This aspect ensures that users can select appropriate wire sizes for their specific applications, promoting both efficiency and compatibility in manufacturing processes. The standard also reflects its commitment to continual improvement and adaptation by introducing significant changes from previous editions. These include enhanced requirements for appearance, ensuring the product meets aesthetic and functional standards, as well as the introduction of a new pin hole test which enhances quality assurance measures. While certain tests, like the springiness test and high temperature failure test, have been removed due to their inappropriateness, the modifications demonstrate a thoughtful approach to maintaining the integrity of the testing process. Overall, IEC 60317-15:2004 is a pertinent document that provides vital specifications for polyesterimide enamelled round aluminium winding wire, ensuring high performance and reliability in electrical applications. Its strengths lie in its comprehensive scope, clear grading, and adaptability to evolving industry standards.
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.
Loading comments...