Fire hazard testing - Part 2-20: Glowing/hot-wire based test methods - Hot wire coil test method - Apparatus, verification, test method and guidance

IEC TS 60695-2-20:2021 describes a test method that applies to solid electrical insulating materials of which test specimens can be provided. The test measures the time required to ignite a test specimen when it is affected by heat from an electrically heated wire wound around the test specimen. If the test specimen drips, the time at which this occurs is also recorded.
The test method can be used to provide classifications which can be used for quality assurance, the preselection of materials of products as described in IEC 60695-1-30, or to verify the required minimum classification of materials used in end products.
This basic safety publication is intended for use by technical committees in the preparation of standards in accordance with the principles laid down in IEC Guide 104 and ISO/IEC Guide 51.
One of the responsibilities of a technical committee is, wherever applicable, to make use of basic safety publications in the preparation of its publications. The requirements, test methods or test conditions of this basic safety publication will not apply unless specifically referred to or included in the relevant publications.
This third edition of IEC TS 60695-2-20 cancels and replaces the second edition of IEC TS 60695-2-20 published in 2004. This edition constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous edition:
– Contents page added
– Updated Scope (Clause 1)
– Updated Terms and Definitions, added new relevant terms (Clause 3)
– Updated Principle (Clause 4)
– Updated Apparatus (Clause 5; recommendation to change the power source from a.c. to d.c. with a constant current output. Reason for this recommendation: d.c. technology is easier to obtain and to handle, which has been found to improve the Repeatability and Reproducibility of the test.
– Updated Test specimen dimensions (6.2)
– Revised Test procedure (Clause 8)
– Revised Observations and measurements (Clause 9)
– Revised Evaluation of test results (Clause 10)
– Revised Test report (Clause 11)
– Revised Annex A: Deletion of conformational test; Guidance on verification of the heater wire winding before testing
– Addition of normative Annex B: HWCT PLC Classes
– Addition of informative Annex C: Calibration curve to determine test current (Ic) in a spreadsheet program
– Addition of informative Annex D: Precision data
It has the status of a basic safety publication in accordance with IEC Guide 104 and ISO/IEC Guide 51.
This basic safety publication is intended for use by technical committees in the preparation of standards in accordance with the principles laid down in IEC Guide 104 and ISO/IEC Guide 51.

General Information

Status
Published
Publication Date
26-Apr-2021
Current Stage
PPUB - Publication issued
Start Date
21-May-2021
Completion Date
27-Apr-2021
Ref Project

Relations

Buy Standard

Technical specification
IEC TS 60695-2-20:2021 - Fire hazard testing - Part 2-20: Glowing/hot-wire based test methods - Hot wire coil test method - Apparatus, verification, test method and guidance
English language
30 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)


IEC TS 60695-2-20 ®
Edition 3.0 2021-04
TECHNICAL
SPECIFICATION
colour
inside
Fire hazard testing –
Part 2-20: Glowing/hot wire based test methods – Hot-wire coil test method –
Apparatus, verification, test method and guidance
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form
or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from
either IEC or IEC's member National Committee in the country of the requester. If you have any questions about IEC
copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or
your local IEC member National Committee for further information.

IEC Central Office Tel.: +41 22 919 02 11
3, rue de Varembé info@iec.ch
CH-1211 Geneva 20 www.iec.ch
Switzerland
About the IEC
The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes
International Standards for all electrical, electronic and related technologies.

About IEC publications
The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the
latest edition, a corrigendum or an amendment might have been published.

IEC publications search - webstore.iec.ch/advsearchform IEC online collection - oc.iec.ch
The advanced search enables to find IEC publications by a Discover our powerful search engine and read freely all the
variety of criteria (reference number, text, technical publications previews. With a subscription you will always
committee, …). It also gives information on projects, replaced have access to up to date content tailored to your needs.
and withdrawn publications.
Electropedia - www.electropedia.org
IEC Just Published - webstore.iec.ch/justpublished
The world's leading online dictionary on electrotechnology,
Stay up to date on all new IEC publications. Just Published
containing more than 22 000 terminological entries in English
details all new publications released. Available online and
and French, with equivalent terms in 18 additional languages.
once a month by email.
Also known as the International Electrotechnical Vocabulary

(IEV) online.
IEC Customer Service Centre - webstore.iec.ch/csc

If you wish to give us your feedback on this publication or
need further assistance, please contact the Customer Service
Centre: sales@iec.ch.
IEC TS 60695-2-20 ®
Edition 3.0 2021-04
TECHNICAL
SPECIFICATION
colour
inside
Fire hazard testing –
Part 2-20: Glowing/hot wire based test methods – Hot-wire coil test method –

Apparatus, verification, test method and guidance

INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
ICS 13.220.40, 29.020 ISBN 978-2-8322-9707-0

– 2 – IEC TS 60695-2-20:2021 © IEC 2021
CONTENTS
FOREWORD . 4
INTRODUCTION . 7
1 Scope . 8
2 Normative references . 8
3 Terms and definitions . 9
4 Principle . 11
5 Apparatus . 12
5.1 Test chamber . 12
5.2 Heater wire . 12
5.3 Power supply and test circuit . 13
5.4 Test specimen fixture . 13
5.5 Test specimen winding and pressing . 13
5.6 Conditioning chamber . 14
5.7 Timing device . 15
5.8 Micrometer . 15
5.9 Measuring scale . 15
6 Test specimens . 15
6.1 Test specimen preparation . 15
6.2 Test specimen dimensions . 15
7 Conditioning . 16
7.1 Requirements . 16
7.2 Test specimen conditioning . 16
7.3 Heater wire conditioning . 16
7.4 Test conditions . 16
8 Test procedure . 17
8.1 General . 17
8.2 Apparatus . 17
8.3 Determination of the test current, I . 17
c
8.4 Calculation of test current, I . 18
c
8.5 Determination of time to ignite, IT and/or time to drip, DT . 18
9 Observations and measurement . 20
10 Evaluation of test results . 21
10.1 Assigning a HWCT PLC classification . 21
10.2 Precision data . 21
11 Test report . 21
Annex A (informative) Guidance on how to effectively wind the heater wire on to the
test specimen . 22
Annex B (normative) Hot wire coil test (HWCT) – Performance level category (PLC)
classes . 23
B.1 General . 23
B.2 Reporting a classification . 23
Annex C (informative) Calibration curve to determine test current (I ) in a spreadsheet
c
program . 24
Annex D (informative) Precision data . 25
D.1 General . 25

D.2 Results of preliminary inter-laboratory round robin . 25
D.3 Evaluation of test results . 28
Bibliography . 30

Figure 1 – Test fixture arrangement (example) . 11
Figure 2 – Test specimen winding pattern . 12
Figure 3 – Test specimen fixture (example) . 13
Figure 4 – Heater wire winding device (Example) . 14
Figure 5 – Test circuit arrangement for heater wire calibration . 17
Figure 6 – Calibration curve . 18
Figure 7 – Decision tree . 20
Figure A.1 – Illustration of type a) behaviour . 22
Figure A.2 – Illustration of type b) behaviour . 22
Figure C.1 – Calibration curve in a spreadsheet program used to determine I . 24
c
Table 1 – Nominal thickness tolerances . 16
Table B.1 – Hot wire coil test (HWCT) – Performance level category (PLC) classes . 23
Table D.1 – Results for material 1A . 26
Table D.2 – Results for material 1B . 26
Table D.3 – Results for material 2A . 26
Table D.4 – Results for material 2B . 27
Table D.5 – Results for material 3 . 27
Table D.6 – Results for material 4 . 28
Table D.7 – Occurrence of PLC classes in the round robin . 29

– 4 – IEC TS 60695-2-20:2021 © IEC 2021
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
FIRE HAZARD TESTING –
Part 2-20: Glowing/hot wire based test methods –
Hot-wire coil test method –
Apparatus, verification, test method and guidance

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international
co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and
in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports,
Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their
preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with
may participate in this preparatory work. International, governmental and non-governmental organizations liaising
with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for
Standardization (ISO) in accordance with conditions determined by agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence between
any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or an
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.