Fireworks — Categories 1, 2 and 3 — Part 3: Minimum labelling requirements

ISO 25947-3:2017 specifies the minimum labelling requirements for the article and primary or selection packaging of fireworks of the following types: - aerial wheels; - bangers; - batteries; - batteries requiring external support; - Bengal flames; - Bengal matches; - Bengal sticks; - Christmas crackers; - combinations; - combinations requiring external support; - compound fireworks; - crackling granules; - double bangers; - double flash bangers; - flash bangers; - flash pellets; - fountains; - ground movers; - ground spinners; - hand-held sparklers; - jumping crackers; - jumping ground spinners; - mines; - mini rockets; - nezumi-hanabi; - non-hand-held sparklers; - novelty matches; - party poppers; - rockets; - Roman candles; - senko-hanabi; - serpents; - shot tubes; - snaps; - spinners; - table bombs; - throwdowns; - wheels. ISO 29547-3:2017 does not apply for theatrical pyrotechnic articles which are designed for indoor or outdoor stage use, including film and television productions or similar use.

Artifices de divertissement — Catégories 1, 2 et 3 — Partie 3: Étiquetage minimal

L'ISO 25947-3:2017 spécifie les exigences minimales d'étiquetage applicables à l'article et à l'emballage primaire ou à l'assortiment des artifices de divertissement des types suivants: - soucoupes volantes; - pétards à mèche; - batteries; - batteries nécessitant un support externe; - feux de Bengale; - allumettes Bengale; - baguettes Bengale; - pétards papillote; - combinaisons; - combinaisons nécessitant un support externe; - compositions d'artifices de divertissement; - crépitants; - pétards aériens; - pétards aériens à composition flash; - pétards à composition flash; - clignoteurs pyrotechniques; - fontaines; - serpenteaux; - tourbillons; - cierges magiques tenus à la main; - pétards sauteurs; - tourbillons sauteurs; - pots à feu en mortier; - mini fusées; - nezumi-hanabis; - cierges magiques non tenus à la main; - allumettes «détonantes»; - party poppers; - fusées; - chandelles romaines; - senko-hanabis; - serpents; - chandelles monocoup; - pétards à tirette; - tourbillons volants; - bombes de table; - pois fulminants; - soleils. L'ISO 25947-3:2017 ne s'applique pas aux articles pyrotechniques pour le théâtre qui sont destinés à un emploi intérieur ou extérieur sur scène, y compris les productions filmographiques et télévisuelles ou les usages similaires.

General Information

Status
Published
Publication Date
22-Mar-2017
Technical Committee
Drafting Committee
Current Stage
9093 - International Standard confirmed
Completion Date
26-Sep-2022
Ref Project

Buy Standard

Standard
ISO 25947-3:2017 - Fireworks -- Categories 1, 2 and 3
English language
27 pages
sale 15% off
Preview
sale 15% off
Preview
Standard
ISO 25947-3:2017 - Artifices de divertissement -- Catégories 1, 2 et 3
French language
35 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 25947-3
First edition
2017-04
Fireworks — Categories 1, 2 and 3 —
Part 3:
Minimum labelling requirements
Artifices de divertissement — Catégories 1, 2 et 3 —
Partie 3: Etiquetage minimal
Reference number
ISO 25947-3:2017(E)
©
ISO 2017

---------------------- Page: 1 ----------------------
ISO 25947-3:2017(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2017, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2017 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 25947-3:2017(E)

Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 2
3 Terms and definitions . 2
4 Minimum labelling requirements . 2
4.1 General and specific labelling requirements . 2
4.1.1 General labelling requirements . 2
4.1.2 Specific labelling requirement for batteries, batteries requiring external
support, combinations and combinations requiring external support . 3
4.1.3 Specific labelling requirement for selection packs . 3
4.1.4 Specific labelling requirements for compound fireworks . 3
4.2 Type of firework, category and registration number . 4
4.3 Minimum age limits . 4
4.4 Explosive content . 4
4.5 Year of production . 4
4.6 Safety information . 5
4.7 Details of manufacturer or importer. 5
4.8 Printing . 5
4.9 Marking of very small items . 5
4.10 Additional information . 5
Annex A (informative) Non-Latin letters .27
© ISO 2017 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO 25947-3:2017(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/ patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO’s adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following
URL: w w w . i s o .org/ iso/ foreword .html.
This document was prepared by Technical Committee ISO/TC 264, Fireworks.
A list of all parts in the ISO 25947 series can be found on the ISO website.
iv © ISO 2017 – All rights reserved

---------------------- Page: 4 ----------------------
INTERNATIONAL STANDARD ISO 25947-3:2017(E)
Fireworks — Categories 1, 2 and 3 —
Part 3:
Minimum labelling requirements
1 Scope
This document specifies the minimum labelling requirements for the article and primary or selection
packaging of fireworks of the following types:
— aerial wheels;
— bangers;
— batteries;
— batteries requiring external support;
— Bengal flames;
— Bengal matches;
— Bengal sticks;
— Christmas crackers;
— combinations;
— combinations requiring external support;
— compound fireworks;
— crackling granules;
— double bangers;
— double flash bangers;
— flash bangers;
— flash pellets;
— fountains;
— ground movers;
— ground spinners;
— hand-held sparklers;
— jumping crackers;
— jumping ground spinners;
— mines;
— mini rockets;
— nezumi-hanabi;
© ISO 2017 – All rights reserved 1

---------------------- Page: 5 ----------------------
ISO 25947-3:2017(E)

— non-hand-held sparklers;
— novelty matches;
— party poppers;
— rockets;
— Roman candles;
— senko-hanabi;
— serpents;
— shot tubes;
— snaps;
— spinners;
— table bombs;
— throwdowns;
— wheels.
This document does not apply for theatrical pyrotechnic articles which are designed for indoor or
outdoor stage use, including film and television productions or similar use.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 25947-1, Fireworks — Fireworks, Categories 1, 2 and 3 — Part 1: Terminology
ISO 25947-2, Fireworks — Fireworks, Categories 1, 2 and 3 — Part 2: Categories and types of firework
ISO 25947-4:—, Fireworks — Fireworks, Categories 1, 2 and 3 — Part 4: Test methods
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 25947-1 apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— IEC Electropedia: available at http:// www .electropedia .org/
— ISO Online browsing platform: available at http:// www .iso .org/ obp
4 Minimum labelling requirements
4.1 General and specific labelling requirements
4.1.1 General labelling requirements
Fireworks shall be marked in accordance with 4.9 and 4.10, with the information specified in 4.1.2 to
4.1.4 (if applicable) and 4.2 to 4.8.
2 © ISO 2017 – All rights reserved

---------------------- Page: 6 ----------------------
ISO 25947-3:2017(E)

Primary packs, if any, shall be marked with the information specified in 4.2 to 4.8 and 4.10.
For the following fireworks, where the use of a primary pack is mandatory, the marking shall be applied
solely to the primary pack:
— Bengal matches;
— Bengal sticks;
— Christmas crackers;
— compound fireworks;
— crackling granules;
— flash pellets;
— hand-held sparklers;
— jumping crackers;
— nezumi-hanabi;
— non-hand-held sparklers;
— novelty matches;
— senko-hanabi;
— serpents;
— snaps;
— throwdowns.
The specified information shall be given in the official language(s) of the country in which the fireworks
or primary packs are offered for retail sale. For each language, it shall be presented as a whole and shall
not be interrupted by other text. Additional text given in another language shall not conflict with the
specified information.
Conformity to these requirements specified in 4.1 to 4.10 shall be verified by visual examination.
4.1.2 Specific labelling requirement for batteries, batteries requiring external support,
combinations and combinations requiring external support
For batteries, batteries requiring external support, combinations and combinations requiring external
support equipped with two initial fuses, the second fuse shall be clearly marked with the words
“RESERVE FUSE”.
4.1.3 Specific labelling requirement for selection packs
Selection packs containing one or more categories shall be marked with the highest category in the
pack, for example, “CAT 3”.
4.1.4 Specific labelling requirements for compound fireworks
The compound fireworks shall be labelled on the primary pack according to the requirements of 4.2 to
4.10. The label of the primary pack shall identify all included articles used in the compound fireworks
according to 4.2. For compound fireworks with two initial fuses, the second fuse shall be clearly marked
with the words “RESERVE FUSE”.
© ISO 2017 – All rights reserved 3

---------------------- Page: 7 ----------------------
ISO 25947-3:2017(E)

Fireworks which are assembled in compound fireworks shall not be labelled with the information
according to 4.3 and the safety information according to 4.6.
4.2 Type of firework, category and registration number
The type of firework shall be marked, in upper case, in conformity with ISO 25947-2. If a trade name is
used in addition to the type name, it shall not conflict with the principal effects of the relevant type of
firework or with the name of another type of firework. For Roman candles, the number of shots shall be
marked, for example, “8 SHOT ROMAN CANDLE”.
The category shall be marked, in upper case, for example, “CATEGORY 2” or “CAT 2”.
Additional traceability information regarding the performed batch testing, for example, lot number,
may be displayed on the label of the article or the smallest piece of packaging.
The registration number, if any, shall be marked on the label. Examples for registration numbers are
given below.
EXAMPLE 1 A registration number used in Japan is given as an example below.
   V – 00 – xxxx
where V refers to the type of firework, 00 refers to the number linked to the country of the manufacturer or
importer (e.g. 00 for Japan) and xxxx refers to the serial number.
EXAMPLE 2 A registration number used in the European Union is given as an example below.
   XXXX – YY – ZZZZ…
where XXXX refers to the identification number of the notified body issuing the certificate, YY refers to the
category of firework in abbreviated format (F1, F2, or F3 for category 1, 2 or 3 respectively) and where ZZZZ is a
processing number used by the notified body.
4.3 Minimum age limits
The minimum age limits applicable in the country in which the fireworks are offered for retail sale
and usage shall be clearly stated on the label. The following minimum age limits apply, if the individual
State has not changed these age limits:
— Category 1: 12 years;
— Category 2: 16 years;
— Category 3: 18 years.
4.4 Explosive content
The labelling shall include the net explosive content or the total NEC of the firework.
For fireworks where the use of a primary pack is mandatory (see 4.1.1) and for fireworks not labelled
completely with the information specified in 4.2 to 4.7, the total NEC or the net explosive content of the
items in the primary pack shall be given on the primary pack.
The abbreviation for the net explosive content (NEC) may be used for the labelling.
4.5 Year of production
For category 3 fireworks, the year of production shall be clearly stated on the bottom right-hand corner
of the label, either by four or by two digits, e.g. “2010” or “10”.
4 © ISO 2017 – All rights reserved

---------------------- Page: 8 ----------------------
ISO 25947-3:2017(E)

4.6 Safety information
The labelling shall include at least the safety information specified in Table 1, in a logical sequence, for
the relevant type of firework. If necessary, instructions in addition to those specified in Table 1 may be
given. The appropriate placing instructions, selected from those specified in Table 1, shall replace
“< placing instructions >”
where indicated.
Safety information shall be emphasized by use of a heading, or bold type, or similar.
4.7 Details of manufacturer or importer
Labelling shall include the name and the address of the manufacturer or the importer.
The address shall comprise at least the town and the country.
4.8 Printing
Labelling shall be clearly visible, easily legible, indelible and on a contrasting background colour.
Printing errors which are not misleading are not classified as faults. If Latin characters are used, and
when measured in accordance with ISO 25947-4:—, 6.7, the type sizes shall be such that the height of
the character “X” (in upper case) is at least 2,8 mm for the information on fireworks type and category
(4.2), safety information (4.6) and additional information (4.10) on the primary pack, if applicable, and
at least 2,1 mm for the other information.
In case of characters other than Latin, the Annex A applies.
4.9 Marking of very small items
If the firework does not provide enough space for the specified information using the type sizes
specified in 4.8, for the information on name and category and safety information, the type size shall be
reduced to 2,1 mm. If the firework does not provide enough space to carry all the specified information
even in reduced type size, at least the information on the manufacturer or the importer shall be given
on the firework.
4.10 Additional information
If the firework is not labelled completely with the information specified in Table 1, or if the primary
pack acts as protection for the initial fuses, the firework shall be sold only in a primary pack. The
primary pack shall be marked with the statement: “Must be sold as packaged”. If the selection pack acts
as protection for initial fuse(s) it shall be marked with the statement: “Must be sold as packaged”. This
statement shall appear adjacent to the type name or category. For printing 4.8 applies.
© ISO 2017 – All rights reserved 5

---------------------- Page: 9 ----------------------
ISO 25947-3:2017(E)

Table 1 — Safety information
Fireworks type Category Minimum labelling requirements Placing instructions
aerial wheels 3 ‘For outdoor use only’
‘Avoid overhead obstructions’
‘Place singly on launching device provided
the correct way up’
‘Remove orange fuse cover’ (if applicable)
‘Standing sideways, light fuse at its outermost
end and retire immediately at least 15 m’
‘Spectators must be at least 25 m away‘
bangers 2 ‘For outdoor use only’
‘Remove orange fuse cover’ (if applicable)
‘Place singly on ground and light fuse at
its outermost end and retire immediately
at least 8 m ‘, or
‘Standing sideways, light ignition head and
retire immediately at least 8 m’ or
‘Ignite on the striking surface, place banger
on the ground and retire immediately at
least 8 m’ (whichever is appropriate)
3 ‘For outdoor use only’
‘Remove orange fuse cover’ (if applicable)
‘Place singly on ground and light fuse at
its outermost end and retire immediately
at least 15 m‘ or
‘Standing sideways, light ignition head and
retire immediately at least 15 m’ or
‘Ignite on the striking surface, place banger
on the ground and retire immediately at
least 15 m’ (whichever is appropriate)
‘Spectators must be at least 25 m away‘
batteries 1 ‘Keep away from eyes and ears’
(party poppers) ‘Hold at arms length and point base away
from body and not towards people or animals’
‘Pull string firmly and sharply’
batteries (with 2 ‘For outdoor use only’
one fuse)
‘Avoid overhead obstructions’ (if applicable)
For batteries where the tubes are placed
at an angle:
‘Do not fire near tall buildings, trees or
similar’
‘Remove orange fuse cover’ (if applicable)
‘Place battery on flat ground’
‘Standing sideways, light fuse at its out-
ermost end and retire immediately at
least 8 m”
An arrow indicating firing direction shall
be part of the label (if applicable).
6 © ISO 2017 – All rights reserved

---------------------- Page: 10 ----------------------
ISO 25947-3:2017(E)

Table 1 (continued)
Fireworks type Category Minimum labelling requirements Placing instructions
batteries (with 3 ‘For outdoor use only’
one fuse)
‘Avoid overhead obstructions’ (if applicable)
‘Do not fire near tall buildings, trees or
similar’ (if applicable)
‘Remove orange fuse cover’ (if applicable)
‘Place battery on flat ground’
‘Standing sideways, light fuse at its outermost
end and retire immediately at least 15 m’
‘Spectators must be at least 25 m away‘
An arrow indicating firing direction shall
be part of the label (if applicable).
batteries (with 2 ‘This firework contains two fuses’
two fuses)
‘For outdoor use only’
‘Avoid overhead obstructions’ (if applicable)
For batteries where the tubes are placed
at an angle:
‘Do not fire near tall buildings, trees or
similar’
‘Identify first fuse and remove orange fuse
cover’ (if applicable)
‘Place battery on flat ground’
‘Standing sideways, light fuse at its outer-
most end and retire immediately at least 8 m’
‘In the event that the firework fails to
function completely, wait 15 min before
returning to the firework and then
ENSURING THAT NO PART OF THE BODY
IS POSITIONED ABOVE THE FIREWORK,
locate the second fuse and standing side-
ways, light fuse at its outermost end and
retire immediately at least 8 m’
An arrow indicating firing direction shall
be part of the label (if applicable).
© ISO 2017 – All rights reserved 7

---------------------- Page: 11 ----------------------
ISO 25947-3:2017(E)

Table 1 (continued)
Fireworks type Category Minimum labelling requirements Placing instructions
batteries (with 3 ‘This firework contains two fuses’
two fuses)
‘For outdoor use only’
‘Avoid overhead obstructions’ (if applicable)
‘Do not fire near tall buildings, trees or
similar’ (if applicable)
‘Identify first fuse and remove orange fuse
cover’ (if applicable)
‘Place battery on flat ground’
‘Standing sideways, light fuse at its outermost
end and retire immediately at least 15 m’
‘In the event that the firework fails to
function completely, wait 15 min before
returning to the firework and then
ENSURING THAT NO PART OF THE BODY
IS POSITIONED ABOVE THE FIREWORK,
locate the second fuse and standing side-
ways, light fuse at its outermost end and
retire immediately at least 15 m’
‘Spectators must be at least 25 m away‘
An arrow indicating firing direction shall
be part of the label (if applicable).
batteries 2 ‘For outdoor use only’ For batteries requiring external support
requiring to be buried into soft ground or material:
‘Avoid overhead obstructions’ (if applicable)
external support
‘Insert article upright in soft ground or
(with one fuse)
For batteries requiring external support
other non-flammable material, e.g. sand’.
where the tubes are placed at an angle:
For batteries requiring external support
‘Do not fire near tall buildings, trees or
to be fixed to a post:
similar’
‘Fix article firmly and upright to a solid post’
‘Remove orange fuse cover’ (if applicable)
‘Ensure top of article clears post’
< placing instructions >
For batteries requiring external support
‘Standing sideways, light fuse at its out-
to be supported by heavy objects, e.g.
ermost end and retire immediately at
sand bags:
least 8 m”
‘Closely surround article with heavy
An arrow indicating firing direction shall
objects on all sides. ‘
be part of the label (if applicable).
For batteries requiring external support
supplied with a special holding device,
or for which particular instructions are
necessary, the manufacturer or importer
shall provide appropriate instructions
8 © ISO 2017 – All rights reserved

---------------------- Page: 12 ----------------------
ISO 25947-3:2017(E)

Table 1 (continued)
Fireworks type Category Minimum labelling requirements Placing instructions
batteries 3 ‘For outdoor use only’ (see placing instructions for category 2
requiring batteries requiring external support)
‘Avoid overhead obstructions’ (if applicable)
external support
(with one fuse)
‘Do not fire near tall buildings, trees or
similar’ (if applicable)
‘Remove orange fuse cover’ (if applicable)
< placing instructions >
‘Standing sideways, light fuse at its outermost
end and retire immediately at least 15 m’
‘Spectators must be at least 25 m away‘
An arrow indicating firing direction shall
be part of the label (if applicable).
batteries ‘This firework contains two fuses’ For batteries requiring external support
requiring to be buried into soft ground or material:
‘For outdoor use only’
external support
‘Insert article upright in soft ground or
(with two fuses)
‘Avoid overhead obstructions’ (if applicable)
other non-flammable material, e.g. sand’.
For batteries requiring external support
For batteries requiring external support
where the tubes are placed at an angle:
to be fixed to a post:
‘Do not fire near tall buildings, trees or
‘Fix article firmly and upright to a solid post’
similar’
‘Ensure top of article clears post’
‘Identify first fuse and remove orange fuse
cover’ (if applicable) For batteries requiring external support
to be supported by heavy objects, e.g.
< placing instructions >
sand bags:
‘Standing sideways, light fuse at its outer-
‘Closely surround article with heavy
most end and retire immediately at least 8 m’
objects on all sides.‘
‘In the event that the firework fails to
For batteries requiring external support
function completely, wait 15 min before
supplied with a special holding device,
returning to the firework and then
or for which particular instructions are
ENSURING THAT NO PART OF THE BODY necessary, the manufacturer or importer
IS POSITIONED ABOVE THE FIREWORK, shall provide appropriate instructions
locate the second fuse and standing side-
ways, light fuse at its outermost end and
retire immediately at least 8 m’
An arrow indicating firing direction shall
be part of the label (if applicable).
© ISO 2017 – All rights reserved 9

---------------------- Page: 13 ----------------------
ISO 25947-3:2017(E)

Table 1 (continued)
Fireworks type Category Minimum labelling requirements Placing instructions
batteries 3 ‘This firework contains two fuses’ (see placing instructions for category 2
requiring batteries requiring external support)
‘For outdoor use only’
external support
(with two fuses)
‘Avoid overhead obstructions’ (if applicable)
‘Do not fire near tall buildings, trees or
similar’ (if applicable)
‘Identify first fuse and remove orange fuse
cover’ (if applicable)
< placing instructions >
‘Standing sideways, light fuse at its outermost
end and retire immediately at least 15 m’
‘In the event that the firework fails to
function completely, wait 15 min before
returning to the firework and then
ENSURING THAT NO PART OF THE BODY
IS POSITIONED ABOVE THE FIREWORK,
locate the second fuse and standing side-
ways, light fuse at its outermost end and
retire immediately at least 15 m’
‘Spectators must be at least 25 m away‘
An arrow indicating firing direction shall
be part of the label (if applicable).
Bengal flames 1 ‘For outdoor use only’ For Bengal flames to be placed flat on
the ground:
‘Remove orange fuse cover’ (if applicable)
‘Place Bengal flame flat on the ground’.
‘Do not inhale smoke’
For Bengal flames to be buried into soft
< placing instructions >
ground or material:
‘Standing sideways, light fuse at its outer-
‘Insert Bengal flame upright in soft ground
most end and retire immediately at least
or other non-flammable material, e.g. sand’.
1 m’, or
For Bengal flames supplied with a special
‘Standing sideways, light ignition head and
holding device, or for which particular
retire immediately at least 1 m’ or
instructions are necessary, the manufac-
‘Standing sideways, light sealing paper and turer or importer shall provide appropriate
retire immediately at least 1 m’ (whichever instructions.
is appropriate)
2 ‘For outdoor use only’
‘Remove orange fuse cover’ (if applicable)
‘Do not inhale smoke’
< placing instructions >
‘Standing sideways, light fuse at its outer-
most end and retire immediately at least
8 m’, or
‘Standing sideways, light ignition head and
retire immediately at least 8 m’ (whichever
is appropriate)
10 © ISO 2017 – All rights reserved

---------------------- Page: 14 ----------------------
ISO 25947-3:2017(E)

Table 1 (continued)
Fireworks type Category Minimum labelling requirements Placing instructions
Bengal flames 3 ‘For outdoor use only’ (see placing instructions for category 1
and 2 Bengal flames)
‘Remove orange fuse cover’ (if applicable)
‘Do not inhale smoke’
< placing instructions >
‘Standing sideways, light fuse at its outer-
most end and retire immediately at least
15 m’, or
‘Standing sideways, light ignition head and
retire immediately at least 15 m ‘ (whichever
is appropriate)
‘Spectators must be at least 25 m away‘
Bengal matches 1 ‘Ignite on the striking surface’
‘Use singly’
‘Use only above non-flammable surface’
‘Do not carry Bengal matches loose in
the pocket’
Bengal sticks 1 ‘For outdoor use only’
‘Use singly’
‘Light one Bengal stick at time at its out-
ermost end’
‘Do not use in windy conditions’
‘Hold horizontally’
Keep Bengal stick away from any part of
the body and flammable materials’
Do not inhale smoke’
Bengal sticks 2 ‘For outdoor use only’
‘Use singly’
‘Light one Bengal stick at time at its out-
ermost end’
‘Do not use in windy conditions’
‘Hold horizontally’
‘Keep Bengal stick away from any part of
the body and flammable materials’
‘Do not inhale smoke’
Christmas 1 ‘Do not pull near eyes or ears’
crackers
‘Pull both ends at arms length firmly and
sharply’
‘Do not remove snap’
© ISO 2017 – All rights reserved 11

---------------------- Page: 15 ----------------------
ISO 25947-3:2017(E)

Table 1 (continued)
Fireworks type Category Minimum labelling requirements Placing instructions
c om bi n a t ion s 2 ‘For outdoor use only’
(with one fuse)
‘Avoid overhead obstructions’ (if applicable)
For combinations where the tubes are placed
at an angle:
‘Do not fire near tall buildings, trees or
similar’
‘Remove orange fuse cover’ (if applicable)
‘Place combination on flat ground’
‘Standing sideways, light fuse at its out-
ermost end and retire immediately at
least 8 m”
An arrow indicating firing direction shall
be part of the label (if applicable).
c om bi n a t ion s 3 ‘For outdoor use only’
(with one fuse)
‘Avoid overhead obstructions’ (if applicable)
‘Do not fire near tall buildings, trees or
similar’ (if applicable)
‘Remove orange fuse cover’ (if applicable)
‘Place combination on flat ground’
‘Standing sideways, light fuse at its outermost
end and retire immediately at least 15 m’
‘Spectators must be at least 25 m away‘
An arrow indicating firing direction shall
be part of the label (if applicable).
c om bi n a t ion s 2 ‘This firework contains two fuses’
(with two fuses)
‘For outdoor use only’
‘Avoid overhead obstructions’ (if applicable)
For combinations where the tubes are placed
at an angle:
‘Do not fire near tall buildings, trees or
similar’
‘Identify first fuse and remove orange fuse
cover’ (if applicable)
‘Place combination on flat ground’
‘Standing
...

NORME ISO
INTERNATIONALE 25947-3
Première édition
2017-04
Artifices de divertissement —
Catégories 1, 2 et 3 —
Partie 3:
Étiquetage minimal
Fireworks — Categories 1, 2 and 3 —
Part 3: Minimum labelling requirements
Numéro de référence
ISO 25947-3:2017(F)
©
ISO 2017

---------------------- Page: 1 ----------------------
ISO 25947-3:2017(F)

DOCUMENT PROTÉGÉ PAR COPYRIGHT
© ISO 2017, Publié en Suisse
Droits de reproduction réservés. Sauf indication contraire, aucune partie de cette publication ne peut être reproduite ni utilisée
sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie, l’affichage sur
l’internet ou sur un Intranet, sans autorisation écrite préalable. Les demandes d’autorisation peuvent être adressées à l’ISO à
l’adresse ci-après ou au comité membre de l’ISO dans le pays du demandeur.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2017 – Tous droits réservés

---------------------- Page: 2 ----------------------
ISO 25947-3:2017(F)

Sommaire Page
Avant-propos .iv
1 Domaine d’application . 1
2 Références normatives . 2
3 Termes et définitions . 2
4 Exigences minimales d’étiquetage . 3
4.1 Exigences générales et spécifiques d’étiquetage . 3
4.1.1 Exigences générales d’étiquetage . 3
4.1.2 Exigence d’étiquetage spécifique pour les batteries, les batteries
nécessitant un support externe, les combinaisons et les combinaisons
nécessitant un support externe . 3
4.1.3 Exigences d’étiquetage spécifique pour les assortiments. 4
4.1.4 Exigences d’étiquetage spécifique pour les compositions d’artifices
de divertissement . 4
4.2 Type d’artifice de divertissement, catégorie et numéro d’enregistrement . 4
4.3 Limite d’âge d’utilisation . 4
4.4 Contenu explosif . 4
4.5 Année de fabrication . 5
4.6 Informations de sécurité . 5
4.7 Coordonnées du fabricant ou de l’importateur . 5
4.8 Impression . 5
4.9 Marquage d’éléments de très petite taille . 5
4.10 Informations supplémentaires. 5
Annexe A (informative) Lettres autres que latines .35
© ISO 2017 – Tous droits réservés iii

---------------------- Page: 3 ----------------------
ISO 25947-3:2017(F)

Avant-propos
L’ISO (Organisation internationale de normalisation) est une fédération mondiale d’organismes
nationaux de normalisation (comités membres de l’ISO). L’élaboration des Normes internationales est
en général confiée aux comités techniques de l’ISO. Chaque comité membre intéressé par une étude
a le droit de faire partie du comité technique créé à cet effet. Les organisations internationales,
gouvernementales et non gouvernementales, en liaison avec l’ISO participent également aux travaux.
L’ISO collabore étroitement avec la Commission électrotechnique internationale (IEC) en ce qui
concerne la normalisation électrotechnique.
Les procédures utilisées pour élaborer le présent document et celles destinées à sa mise à jour sont
décrites dans les Directives ISO/IEC, Partie 1. Il convient, en particulier de prendre note des différents
critères d’approbation requis pour les différents types de documents ISO. Le présent document a été
rédigé conformément aux règles de rédaction données dans les Directives ISO/IEC, Partie 2 (voir www
.iso .org/ directives).
L’attention est appelée sur le fait que certains des éléments du présent document peuvent faire l’objet de
droits de propriété intellectuelle ou de droits analogues. L’ISO ne saurait être tenue pour responsable
de ne pas avoir identifié de tels droits de propriété et averti de leur existence. Les détails concernant
les références aux droits de propriété intellectuelle ou autres droits analogues identifiés lors de
l’élaboration du document sont indiqués dans l’Introduction et/ou dans la liste des déclarations de
brevets reçues par l’ISO (voir www .iso .org/ brevets).
Les appellations commerciales éventuellement mentionnées dans le présent document sont données
pour information, par souci de commodité, à l’intention des utilisateurs et ne sauraient constituer un
engagement.
Pour une explication de la nature volontaire des normes, la signification des termes et expressions
spécifiques de l’ISO liés à l’évaluation de la conformité, ou pour toute information au sujet de l’adhésion
de l’ISO aux principes de l’OMC concernant les obstacles techniques au commerce (OTC), voir le lien
suivant: w w w . i s o .org/ iso/ fr/ foreword .html.
Le présent document a été élaboré par le comité technique ISO/TC 264, Artifices de divertissement.
Une liste de toutes les parties de la série ISO 25947 se trouve sur le site Web de l’ISO.
iv © ISO 2017 – Tous droits réservés

---------------------- Page: 4 ----------------------
NORME INTERNATIONALE ISO 25947-3:2017(F)
Artifices de divertissement — Catégories 1, 2 et 3 —
Partie 3:
Étiquetage minimal
1 Domaine d’application
Le présent document spécifie les exigences minimales d’étiquetage applicables à l’article et à l’emballage
primaire ou à l’assortiment des artifices de divertissement des types suivants:
— soucoupes volantes;
— pétards à mèche;
— batteries;
— batteries nécessitant un support externe;
— feux de Bengale;
— allumettes Bengale;
— baguettes Bengale;
— pétards papillote;
— combinaisons;
— combinaisons nécessitant un support externe;
— compositions d’artifices de divertissement;
— crépitants;
— pétards aériens;
— pétards aériens à composition flash;
— pétards à composition flash;
— clignoteurs pyrotechniques;
— fontaines;
— serpenteaux;
— tourbillons;
— cierges magiques tenus à la main;
— pétards sauteurs;
— tourbillons sauteurs;
— pots à feu en mortier;
— mini fusées;
— nezumi-hanabis;
© ISO 2017 – Tous droits réservés 1

---------------------- Page: 5 ----------------------
ISO 25947-3:2017(F)

— cierges magiques non tenus à la main;
— allumettes «détonantes»;
— party poppers;
— fusées;
— chandelles romaines;
— senko-hanabis;
— serpents;
— chandelles monocoup;
— pétards à tirette;
— tourbillons volants;
— bombes de table;
— pois fulminants;
— soleils.
Le présent document ne s’applique pas aux articles pyrotechniques pour le théâtre qui sont destinés à
un emploi intérieur ou extérieur sur scène, y compris les productions filmographiques et télévisuelles
ou les usages similaires.
2 Références normatives
Les documents suivants cités dans le texte constituent, pour tout ou partie de leur contenu, des
exigences du présent document. Pour les références datées, seule l’édition citée s’applique. Pour les
références non datées, la dernière édition du document de référence s’applique (y compris les éventuels
amendements).
ISO 25947-1, Artifices de divertissement — Catégories 1, 2 et 3 — Partie 1: Terminologie
ISO 25947-2, Artifices de divertissement — Catégories 1, 2 et 3 — Partie 2: Catégories et types
ISO 25947-4:2017, Artifices de divertissement — Catégories 1, 2 et 3 — Partie 4: Méthodes d’essai
3 Termes et définitions
Pour les besoins du présent document, les termes et définitions de l’ISO 25947-1 s’appliquent.
L’ISO et l’IEC tiennent à jour des bases de données terminologiques destinées à être utilisées en
normalisation, consultables aux adresses suivantes:
— IEC Electropedia: disponible à l’adresse http:// www .electropedia .org/ .
— ISO Online browsing platform: disponible à l’adresse http:// www .iso .org/ obp.
2 © ISO 2017 – Tous droits réservés

---------------------- Page: 6 ----------------------
ISO 25947-3:2017(F)

4 Exigences minimales d’étiquetage
4.1 Exigences générales et spécifiques d’étiquetage
4.1.1 Exigences générales d’étiquetage
Les artifices de divertissement doivent être marqués conformément à 4.9 et 4.10 avec les informations
spécifiées en 4.1.2 à 4.1.4 (le cas échéant) et 4.2 à 4.8.
Les emballages primaires, s’ils existent, doivent être marqués avec les informations spécifiées en 4.2 à
4.8 et 4.10.
Pour les artifices de divertissement suivants, lorsque l’utilisation d’un emballage primaire est
obligatoire, le marquage doit être appliqué uniquement sur l’emballage primaire:
— allumettes Bengale;
— baguettes Bengale;
— pétards papillote;
— compositions d’artifices de divertissement;
— crépitants;
— clignoteurs pyrotechniques;
— cierges magiques tenus à la main;
— pétards sauteurs;
— nezumi-hanabis;
— cierges magiques non tenus à la main;
— allumettes «détonantes»;
— senko-hanabis;
— serpents;
— pétards à tirette;
— pois fulminants.
Les informations spécifiées doivent être rédigées dans la ou les langues officielles du pays dans lequel
les artifices de divertissement ou les emballages primaires sont destinés à la vente au détail. Pour
chaque langue, elles doivent être regroupées sans être interrompues par un autre texte. Tout texte
supplémentaire dans une autre langue ne doit pas être en contradiction avec les informations spécifiées.
La conformité aux exigences spécifiées en 4.1 à 4.10 doit être vérifiée par examen visuel.
4.1.2 Exigence d’étiquetage spécifique pour les batteries, les batteries nécessitant un support
externe, les combinaisons et les combinaisons nécessitant un support externe
Pour les batteries, les batteries nécessitant un support externe, les combinaisons et les combinaisons
nécessitant un support externe équipées de deux mèches d’allumage, la deuxième mèche d’allumage
doit clairement porter la mention «MÈCHE DE SECOURS».
© ISO 2017 – Tous droits réservés 3

---------------------- Page: 7 ----------------------
ISO 25947-3:2017(F)

4.1.3 Exigences d’étiquetage spécifique pour les assortiments
Les assortiments contenant des articles relevant d’une ou de plusieurs catégories doivent être marqués
pour la catégorie la plus élevée contenue dans l’assortiment, par exemple «CAT 3».
4.1.4 Exigences d’étiquetage spécifique pour les compositions d’artifices de divertissement
Les compositions d’artifices de divertissement doivent être étiquetées sur l’emballage primaire
conformément aux exigences de 4.2 à 4.10. L’étiquette de l’emballage primaire doit identifier tous les
articles inclus utilisés dans les compositions d’artifices de divertissement conformément à 4.2. Pour
les compositions d’artifices de divertissement équipées de deux mèches d’allumage, la deuxième mèche
d’allumage doit clairement porter la mention «MÈCHE DE SECOURS».
Les artifices de divertissement assemblés dans des compositions d’artifices de divertissement ne
doivent pas être étiquetés avec les informations selon 4.3 ni avec les informations de sécurité selon 4.6.
4.2 Type d’artifice de divertissement, catégorie et numéro d’enregistrement
Le type d’artifice de divertissement doit être indiqué, en majuscules, conformément à l’ISO 25947-2.
Si un nom de marque est utilisé en plus du nom de type, il ne doit pas être en contradiction avec l’effet
principal du type d’artifice de divertissement correspondant ou avec le nom d’un autre type d’artifice
de divertissement. Pour les chandelles romaines, le nombre de coups doit être indiqué, par exemple
«CHANDELLE ROMAINE 8 COUPS».
La catégorie doit être marquée, en majuscules, par exemple «CATÉGORIE 2» ou «CAT 2».
D’autres informations de traçabilité concernant les essais de lot réalisés, par exemple le numéro de lot,
peuvent figurer sur l’étiquette de l’article ou sur le plus petit élément d’emballage.
Le numéro d’enregistrement doit, le cas échéant, figurer sur l’étiquette. Des exemples de numéros
d’enregistrement sont donnés ci-dessous.
EXEMPLE 1 Un exemple de numéro d’enregistrement utilisé au Japon est donné ci-dessous.
V – 00 – xxxx
où V fait référence au type d’artifice de divertissement, 00 fait référence au numéro associé au pays du fabricant
ou de l’importateur (par exemple 00 pour le Japon) et xxxx fait référence au numéro de série.
EXEMPLE 2 Un exemple de numéro d’enregistrement utilisé dans l’Union européenne est donné ci-dessous.
XXXX – YY – ZZZZ…
où XXXX fait référence au numéro d’identification de l’organisme notifié ayant délivré le certificat, YY fait
référence à la catégorie d’artifice de divertissement dans un format abrégé (F1, F2 ou F3 pour la catégorie 1, 2 ou
3 respectivement), et où ZZZZ est un numéro de traitement utilisé par l’organisme notifié.
4.3 Limite d’âge d’utilisation
La limite d’âge d’utilisation applicable dans le pays où les artifices de divertissement sont mis en vente
au détail et disponibles à l’utilisation doit être clairement indiquée sur l’étiquette. Les limites d’âge
suivantes s’appliquent sauf si l’État membre concerné les a modifiées:
— Catégorie 1: 12 ans;
— Catégorie 2: 16 ans;
— Catégorie 3: 18 ans.
4.4 Contenu explosif
La masse active ou la MA totale de l’artifice de divertissement doit être indiquée sur l’étiquette.
4 © ISO 2017 – Tous droits réservés

---------------------- Page: 8 ----------------------
ISO 25947-3:2017(F)

Pour les artifices de divertissement pour lesquels l’utilisation d’un emballage primaire est obligatoire
(voir 4.1.1) et pour les artifices de divertissement ne faisant pas mention de l’ensemble des informations
spécifiées en 4.2 à 4.7, la MA totale des éléments contenus dans l’emballage primaire doit être indiquée
sur l’emballage primaire.
L’abréviation pour la masse active (MA) peut être utilisée pour l’étiquetage.
4.5 Année de fabrication
Pour les artifices de divertissement de catégorie 3, l’année de fabrication doit être clairement indiquée
en bas à droite de l’étiquette, avec quatre ou deux chiffres, par exemple «2010» ou «10».
4.6 Informations de sécurité
L’étiquetage doit au moins inclure les informations relatives à la sécurité spécifiées dans le Tableau 1,
dans un ordre logique, pour le type d’artifice de divertissement correspondant. Si nécessaire, des
instructions supplémentaires autres que celles spécifiées dans le Tableau 1 peuvent être indiquées. Les
instructions de mise en place appropriées, sélectionnées à partir de celles spécifiées dans le Tableau 1,
doivent remplacer la mention:
«< instructions d’installation >»
lorsqu’elle est indiquée.
Les informations de sécurité doivent être mises en évidence au moyen d’un titre, ou l’usage de caractères
gras, ou de toute autre mise en forme similaire.
4.7 Coordonnées du fabricant ou de l’importateur
L’étiquetage doit comprendre le nom et l’adresse du fabricant ou de l’importateur.
L’adresse doit au moins inclure la ville et le pays.
4.8 Impression
L’étiquetage doit être clairement visible, facilement lisible, indélébile et sur fond de couleur contrasté.
Les erreurs d’impression n’induisant pas d’erreur pour l’emploi ne sont pas classées comme des défauts.
Si des caractères latins sont utilisés et quand ils sont mesurés selon l’ISO 25947-4:2017, 6.7, les tailles
de caractères doivent être telles que la hauteur du caractère «X» (en majuscule) soit d’au moins 2,8 mm
pour les informations relatives au type et à la catégorie des artifices de divertissement (4.2), aux
informations de sécurité (4.6) et, le cas échéant, aux informations supplémentaires (4.10) figurant sur
l’emballage primaire, et d’au moins 2,1 mm pour les autres informations.
Dans le cas de caractères autres que latins, l’Annexe A s’applique.
4.9 Marquage d’éléments de très petite taille
Si l’artifice de divertissement n’offre pas un espace suffisant pour les informations spécifiées en utilisant
les tailles de caractères spécifiées en 4.8, pour les informations relatives au nom et à la catégorie et
pour les informations de sécurité, la taille de caractères doit être réduite à 2,1 mm. Si l’artifice de
divertissement n’offre pas un espace suffisant pour l’ensemble des informations spécifiées même après
réduction de la taille de caractères, au moins les informations relatives au fabricant ou à l’importateur
doit être indiqué sur l’artifice de divertissement.
4.10 Informations supplémentaires
Si l’artifice de divertissement ne fait pas mention de l’ensemble des informations spécifiées dans le
Tableau 1, ou si l’emballage primaire fait office de protection des mèches d’allumage, l’artifice doit être
vendu uniquement dans son emballage primaire. L’emballage primaire doit comporter la mention: «Doit
© ISO 2017 – Tous droits réservés 5

---------------------- Page: 9 ----------------------
ISO 25947-3:2017(F)

être vendu dans son emballage». Si l’assortiment fait office de protection de la (des) mèche(s) d’allumage,
il doit comporter la mention: «Doit être vendu dans son emballage». Cette instruction doit figurer à côté
du nom de type ou de la catégorie. Pour l’impression, 4.8 s’applique.
Tableau 1 — Informations obligatoires en matière de sécurité
Type d’artifice de
Catégorie Exigences minimales d’étiquetage Instructions d’installation
divertissement
soucoupes volantes 3 «Artifice d’extérieur»
«La zone de tir doit être dégagée de tout obs-
tacle en hauteur»
«À placer individuellement sur son support
de tir - Respecter le sens de tir»
«Retirer le couvre mèche orange» (le cas
échéant)
«En se tenant sur le côté, allumer la mèche à
son extrémité et s’éloigner immédiatement
d’au moins 15 m»
«Les spectateurs doivent être à au moins
25 m»
pétards à mèche 2 «Artifice d’extérieur»
«Retirer le couvre mèche orange» (le cas
échéant)
«Placer individuellement sur le sol et allumer
la mèche à son extrémité et s’éloigner immé-
diatement d’au moins 8 m», ou
«En se tenant sur le côté, allumer la tête
d’allumage et s’éloigner immédiatement d’au
moins 8 m» ou
«Allumer à l’aide du frottoir, placer le pétard
à mèche sur le sol et s’éloigner immédiate-
ment d’au moins 8 m» (selon le cas approprié)
3 «Artifice d’extérieur»
«Retirer le couvre mèche orange» (le cas
échéant)
«Placer individuellement sur le sol, allumer la
mèche à son extrémité et s’éloigner immédia-
tement d’au moins 15 m» ou
«En se tenant sur le côté, allumer la tête
d’allumage et s’éloigner immédiatement d’au
moins 15 m» ou
«Allumer à l’aide du frottoir, placer le pétard à
mèche sur le sol et s’éloigner immédiatement
d’au moins 15 m» (selon le cas approprié)
«Les spectateurs doivent être à au moins
25 m»
batteries 1 «Ne pas utiliser à proximité des yeux et des
oreilles»
(party poppers)
«Maintenir à bout de bras et orienter la base
loin du corps et sans viser d’autres personnes
ou des animaux»
«Tirer la ficelle d’un coup sec»
6 © ISO 2017 – Tous droits réservés

---------------------- Page: 10 ----------------------
ISO 25947-3:2017(F)

Tableau 1 (suite)
Type d’artifice de
Catégorie Exigences minimales d’étiquetage Instructions d’installation
divertissement
batteries (avec une 2 «Artifice d’extérieur»
seule mèche d’allu-
«La zone de tir doit être dégagée de tout obs-
mage)
tacle en hauteur» (le cas échéant)
Pour les batteries dont les tubes sont placés en
position inclinée:
«Ne pas utiliser à proximité de bâtiments,
arbres ou éléments similaires élevés»
«Retirer le couvre mèche orange» (le cas
échéant)
«Placer la batterie sur un sol plat»
«En se tenant sur le côté, allumer la mèche à
son extrémité et s’éloigner immédiatement
d’au moins 8 m»
Une flèche indiquant la direction du tir doit
figurer sur l’étiquette (le cas échéant).
batteries (avec une 3 «Artifice d’extérieur»
seule mèche d’allu-
«La zone de tir doit être dégagée de tout obs-
mage)
tacle en hauteur» (le cas échéant)
«Ne pas utiliser à proximité de bâtiments,
arbres ou éléments similaires élevés» (le cas
échéant)
«Retirer le couvre mèche orange» (le cas
échéant)
«Placer la batterie sur un sol plat»
«En se tenant sur le côté, allumer la mèche à
son extrémité et s’éloigner immédiatement
d’au moins 15 m»
«Les spectateurs doivent être à au moins
25 m»
Une flèche indiquant la direction du tir doit
figurer sur l’étiquette (le cas échéant)
© ISO 2017 – Tous droits réservés 7

---------------------- Page: 11 ----------------------
ISO 25947-3:2017(F)

Tableau 1 (suite)
Type d’artifice de
Catégorie Exigences minimales d’étiquetage Instructions d’installation
divertissement
batteries (avec deux 2 «Cet artifice de divertissement possède deux
mèches d’allumage) mèches d’allumage»
«Artifice d’extérieur»
«La zone de tir doit être dégagée de tout obs-
tacle en hauteur» (le cas échéant)
Pour les batteries dont les tubes sont placés en
position inclinée:
«Ne pas utiliser à proximité de bâtiments,
arbres ou éléments similaires élevés»
«Identifier la première mèche d’allumage
et retirer le couvre mèche orange» (le cas
échéant)
«Placer la batterie sur un sol plat»
«En se tenant sur le côté, allumer la mèche à
son extrémité et s’éloigner immédiatement
d’au moins 8 m»
«Si l’artifice de divertissement ne fonctionne
pas complètement, attendre 15 minutes avant
de s’en approcher puis,
APRÈS S’ÊTRE ASSURÉ QU’AUCUNE PARTIE
DU CORPS NE SE TROUVE AU-DESSUS DE
L’ARTIFICE de divertissement, repérer la deu-
xième mèche d’allumage et, en se tenant sur
le côté, l’allumer à son extrémité et s’éloigner
immédiatement d’au moins 8 m»
Une flèche indiquant la direction du tir doit
figurer sur l’étiquette (le cas échéant)
8 © ISO 2017 – Tous droits réservés

---------------------- Page: 12 ----------------------
ISO 25947-3:2017(F)

Tableau 1 (suite)
Type d’artifice de
Catégorie Exigences minimales d’étiquetage Instructions d’installation
divertissement
batteries (avec deux 3 «Cet artifice de divertissement possède deux
mèches d’allumage) mèches d’allumage»
«Artifice d’extérieur»
«La zone de tir doit être dégagée de tout obs-
tacle en hauteur» (le cas échéant)
«Ne pas utiliser à proximité de bâtiments,
arbres ou éléments similaires élevés» (le cas
échéant)
«Identifier la première mèche d’allumage
et retirer le couvre mèche orange» (le cas
échéant)
«Placer la batterie sur un sol plat»
«En se tenant sur le côté, allumer la mèche à
son extrémité et s’éloigner immédiatement
d’au moins 15 m»
«Si l’artifice de divertissement ne fonctionne
pas complètement, attendre 15 minutes avant
de s’en approcher puis,
APRÈS S’ÊTRE ASSURÉ QU’AUCUNE PARTIE
DU CORPS NE SE TROUVE AU-DESSUS DE
L’ARTIFICE de divertissement, repérer la deu-
xième mèche d’allumage et, en se tenant sur
le côté, l’allumer à son extrémité et s’éloigner
immédiatement d’au moins 15 m»
«Les spectateurs doivent être à au moins
25 m»
Une flèche indiquant la direction du tir doit
figurer sur l’étiquette (le cas échéant)
© ISO 2017 – Tous droits réservés 9

---------------------- Page: 13 ----------------------
ISO 25947-3:2017(F)

Tableau 1 (suite)
Type d’artifice de
Catégorie Exigences minimales d’étiquetage Instructions d’installation
divertissement
batteries néces- 2 «Artifice d’extérieur» Pour les batteries nécessitant
sitant un support un support externe et desti-
«La zone de tir doit être dégagée de tout obs-
externe (avec une nées à être enfoncées dans un
tacle en hauteur» (le cas échéant)
seule mèche d’allu- sol ou matériau meuble:
mage)
Pour les batteries nécessitant un support
«Insérer l’article verticalement
externe et dont les tubes sont placés en position
dans un sol meuble ou autre
inclinée:
matériau non inflammable, du
«Ne pas utiliser à proximité de bâtiments, sable, par exemple»
arbres ou éléments similaires élevés»
Pour les batteries devant être
«Retirer le couvre mèche orange» (le cas fixées à un support vertical
échéant) externe:
«Fixer solidement l’article
< instructions d’installation >
verticalement sur un support
«En se tenant sur le côté, allumer la mèche à
vertical résistant»
son extrémité et s’éloigner immédiatement
d’au moins 8 m» «S’assurer que le sommet de
l’article dépasse du support
Une flèche indiquant la direction du tir doit
vertical»
figurer sur l’étiquette (le cas échéant)
Pour les batteries nécessitant
un support externe destinées
à être soutenues par des objets
lourds, par exemple des sacs
de sable:
«Entourer étroitement
l’article d’objets lourds sur
tous les côtés.»
Pour les batteries nécessitant
un support externe, fournies
avec un support de maintien
spécial, ou pour lesquelles des
instructions particulières sont
nécessaires, le fabricant ou
l’importateur doit fournir les
instructions appropriées
batteries néces- 3 «Artifice d’extérieur» (voir les instructions d’installa-
sitant un support tion pour les batteries de caté-
«La zone de tir doit être dégagée de tout obs-
externe (avec une gorie 2 nécessitant un support
tacle en hauteur» (le cas échéant)
seule mèche d’allu- externe)
mage)
«Ne pas utiliser à proximité de bâtiments,
arbres ou éléments similaires élevés» (le cas
échéant)
«Retirer le couvre mèche orange» (le cas
échéant)
< instructions d’installation >
«En se tenant sur le côté, allumer la mèche à
son extrémité et s’éloigner immédiatement
d’au moins 15 m»
«Les spectateurs doivent être à au moins
25 m»
Une flèche indiquant la direction du tir doit
figurer sur l’étiquette (le cas échéant)
10 © ISO 2017 – Tous droits réservés

---------------------- Page: 14 ----------------------
ISO 25947-3:2017(F)

Tableau 1 (suite)
Type d’artifice de
Catégorie Exigences minimales d’étiquetage Instructions d’installation
divertissement
batteries néces- «Cet artifice de divertissement possède deux Pour les batteries nécessitant
sitant un support mèches d’allumage» un support externe et desti-
externe (avec deux nées à être enfoncées dans un
«Artifice d’extérieur»
mèches d’allumage) sol ou matériau meuble:
«La zone de tir doit être dégagée de tout obs-
«Insérer l’article verticalement
tacle en hauteur» (le cas échéant)
dans un sol meuble ou autre
Pour les batteries nécessitant un support matériau non inflammable, du
externe et dont les tubes sont placés en position sable, par exemple»
inclinée:
Pour les batteries devant être
«Ne pas utiliser à proximité de bâtiments, fixées à un support vertical
arbres ou éléments similaires élevés» externe:
«Fixer solidement l’article
«Identifier la première mèche d’allumage
verticalement sur un support
et retirer le couvre mèche orange» (le cas
vertical résistant»
échéant)
< instructions d’installation > «S’assurer que le sommet de
l’article dépasse du support
«En se tenant sur le côté, allumer la mèche à
vertical»
son extrémité et s’éloigner immédiatement
d’au moins 8 m» Pour les batteries nécessitant
un support externe destinées
«Si l’artifice de divertissement ne fonctionne
à être soutenues par des objets
pas complètement, attendre 15 minutes avant
lourds, par exemple des sacs
de s’en approcher puis,
de sable:
APRÈS S’ÊTRE ASSURÉ QU’AUCUNE PARTIE
«Entourer étroitement
DU CORPS NE SE TROUVE AU-DESSUS DE
l’article d’objets lourds sur
L’ARTIFICE de divertissement, repérer la deu-
tous les côtés.»
xième mèche d’allumage et, en se tenant sur
le côté, l’allumer à son extrémité et s’éloigner Pour les batteries nécessitant
immédiatement d’au moins 8 m» un support externe, fournies
avec un support de maintien
Une flèche indiquant la direction du tir doit
spécial, ou pour lesquelles des
figurer sur l’étiquette (le cas échéant)
instructions particulières sont
nécessaires, le fabricant ou
l’importateur doit fournir les
instructions appropriées
© ISO 2017 – Tous droits réservés 11

---------------------- Page: 15 ----------------------
ISO 259
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.