ISO/TS 13399-303:2016
(Main)Cutting tool data representation and exchange — Part 303: Creation and exchange of 3D models — Solid end mills
Cutting tool data representation and exchange — Part 303: Creation and exchange of 3D models — Solid end mills
ISO/TS 13399-303:2016 specifies a concept for the design of tool items, limited to solid (non-indexable) end mills, with the usage of the related properties and domains of values. ISO/TS 13399-303:2016 specifies a common way of design simplified models that contain the following: - definitions and identifications of the design features of solid (non-indexable) end mills, with a link to the properties used; - definitions and identifications of the internal structure of the 3D model that represents features and properties of solid (non-indexable) end mills. The following are outside the scope of this part of ISO/TS 13399: - applications where these standard data may be stored or referenced; - creation and exchange of simplified 3D models for cutting tools; - creation and exchange of simplified 3D models for cutting items; - creation and exchange of simplified 3D models for other tool items not being described in the scope of this part of ISO/TS 13399; - creation and exchange of simplified 3D models for adaptive items; - creation and exchange of simplified 3D models for assembly items and auxiliary items.
Représentation et échange des données relatives aux outils coupants — Partie 303: Création et échange de modèles 3D — Fraises cylindriques deux tailles monobloc
La présente partie de l'ISO/TS 13399 spécifie un concept pour la conception des éléments relatifs aux outils, limité aux fraises cylindriques deux tailles monobloc (non-amovibles), utilisant les propriétés et domaines de valeurs associés. La présente partie de l'ISO/TS 13399 spécifie une façon commune de concevoir des modèles simplifiés contenant les éléments suivants: — des définitions et identifications des caractéristiques de conception des fraises cylindriques deux tailles monobloc (non-amovibles), avec un lien vers les propriétés utilisées; — des définitions et identifications de la structure interne du modèle 3D qui représente les caractéristiques et les propriétés des fraises cylindriques deux tailles monobloc (non-amovibles); Les éléments suivants n'entrent pas dans le domaine d'application de la présente partie de l'ISO/TS 13399: — les applications où les données standards peuvent être stockées ou référencées; — le concept de modèles 3D pour les outils coupants; — le concept de modèles 3D pour les éléments coupants; — le concept de modèles 3D pour d'autres éléments de l'outil non décrits dans la présente partie de l'ISO/TS 13399; — le concept de modèles 3D pour les éléments relatifs aux attachements; — le concept de modèles 3D pour les éléments relatifs aux assemblages et éléments auxiliaires.
General Information
Buy Standard
Standards Content (Sample)
TECHNICAL ISO/TS
SPECIFICATION 13399-303
First edition
Cutting tool data representation and
exchange —
Part 303:
Creation and exchange of 3D models
— Solid end mills
Représentation et échange des données relatives aux outils coupants —
Partie 303: Création et échange de modèles 3D — Fraises cylindriques
deux tailles monobloc
PROOF/ÉPREUVE
Reference number
ISO/TS 13399-303:2015(E)
©
ISO 2015
ISO/TS 13399-303:2015(E)
© ISO 2015, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2015 – All rights reserved
ISO/TS 13399-303:2015(E)
Contents Page
Foreword .v
Introduction .vii
1 Scope . 1
2 Normative references . 1
3 Starting elements, coordinate systems, planes . 2
3.1 General . 2
3.2 Reference system . 2
3.3 Coordinate system at the cutting part . 3
3.4 Planes . 3
3.5 Cutting reference point (CRP) . 4
4 Design of the model . 5
4.1 General . 5
4.2 Necessary parameters for the connection interface feature . 5
5 Non-centre cutting end mill . 5
5.1 General . 5
5.2 Necessary properties . 6
5.3 Geometry of the non-cutting part inclusive of the connection . 7
5.4 Geometry of the cutting part . 7
5.5 Complete non-centre cutting end mill . 8
6 Centre cutting end mill . 9
6.1 General . 9
6.2 Necessary properties . 9
6.3 Geometry of the non-cutting part inclusive of the connection . 9
6.4 Geometry of the cutting part .10
6.5 Complete centre cutting end mill .10
7 Angular end mill (V-groove) .11
7.1 General .11
7.2 Necessary properties .11
7.3 Geometry of the non-cutting part inclusive of the connection .11
7.4 Geometry of the cutting part .12
7.5 V-groove end mill, complete .13
8 Dovetail end mill .13
8.1 General .13
8.2 Necessary properties .13
8.3 Geometry of the non-cutting part inclusive of the connection .13
8.4 Geometry of the cutting part .14
8.5 Complete dovetail end mill, complete .15
9 T-slot end mill .15
9.1 General .15
9.2 Necessary properties .15
9.3 Geometry of the non-cutting part inclusive of the connection .15
9.4 Geometry of the cutting part .16
9.5 Complete T-slot end mill .16
10 Ball-nosed end mill .17
10.1 General .17
10.2 Necessary properties .17
10.3 Geometry of the non-cutting part inclusive of the connection .18
10.4 Geometry of the cutting part .18
10.5 Complete ball-nosed end mill.18
11 Die end mill .19
ISO/TS 13399-303:2015(E)
11.1 General .19
11.2 Necessary properties .19
11.3 Geometry of the non-cutting part inclusive of the connection .20
11.4 Geometry of the cutting part .20
11.5 Complete die end mill .20
12 Concave rounded profile end mill .21
12.1 General .21
12.2 Necessary properties .21
12.3 Geometry of the non-cutting part inclusive of the connection .21
12.4 Geometry of the cutting part .21
12.5 Complete concave rounded profile end mill .22
13 Thread end mill .23
13.1 General .23
13.2 Necessary properties .23
13.3 Geometry of the non-cutting part inclusive of the connection .24
13.4 Geometry of the cutting part .24
13.5 Complete thread end mill .24
14 Cutting stylus .25
14.1 General .25
14.2 Necessary properties .25
14.3 Geometry of the non-cutting part inclusive of the connection .26
14.4 Geometry of the cutting part .
...
TECHNICAL ISO/TS
SPECIFICATION 13399-303
First edition
2016-02-01
Cutting tool data representation and
exchange —
Part 303:
Creation and exchange of 3D models
— Solid end mills
Représentation et échange des données relatives aux outils coupants —
Partie 303: Création et échange de modèles 3D — Fraises cylindriques
deux tailles monobloc
Reference number
©
ISO 2016
© ISO 2016, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2016 – All rights reserved
Contents Page
Foreword .v
Introduction .vii
1 Scope . 1
2 Normative references . 1
3 Starting elements, coordinate systems, planes . 2
3.1 General . 2
3.2 Reference system . 2
3.3 Coordinate system at the cutting part . 3
3.4 Planes . 3
3.5 Cutting reference point (CRP) . 4
4 Design of the model . 5
4.1 General . 5
4.2 Necessary parameters for the connection interface feature . 5
5 Non-centre cutting end mill . 5
5.1 General . 5
5.2 Necessary properties . 6
5.3 Geometry of the non-cutting part inclusive of the connection . 7
5.4 Geometry of the cutting part . 7
5.5 Complete non-centre cutting end mill . 8
6 Centre cutting end mill . 9
6.1 General . 9
6.2 Necessary properties . 9
6.3 Geometry of the non-cutting part inclusive of the connection . 9
6.4 Geometry of the cutting part .10
6.5 Complete centre cutting end mill .10
7 Angular end mill (V-groove) .11
7.1 General .11
7.2 Necessary properties .11
7.3 Geometry of the non-cutting part inclusive of the connection .11
7.4 Geometry of the cutting part .12
7.5 V-groove end mill, complete .13
8 Dovetail end mill .13
8.1 General .13
8.2 Necessary properties .13
8.3 Geometry of the non-cutting part inclusive of the connection .13
8.4 Geometry of the cutting part .14
8.5 Complete dovetail end mill, complete .15
9 T-slot end mill .15
9.1 General .15
9.2 Necessary properties .15
9.3 Geometry of the non-cutting part inclusive of the connection .15
9.4 Geometry of the cutting part .16
9.5 Complete T-slot end mill .16
10 Ball-nosed end mill .17
10.1 General .17
10.2 Necessary properties .17
10.3 Geometry of the non-cutting part inclusive of the connection .18
10.4 Geometry of the cutting part .18
10.5 Complete ball-nosed end mill.18
11 Die end mill .19
11.1 General .19
11.2 Necessary properties .19
11.3 Geometry of the non-cutting part inclusive of the connection .20
11.4 Geometry of the cutting part .20
11.5 Complete die end mill .20
12 Concave rounded profile end mill .21
12.1 General .21
12.2 Necessary properties .21
12.3 Geometry of the non-cutting part inclusive of the connection .21
12.4 Geometry of the cutting part .21
12.5 Complete concave rounded profile end mill .22
13 Thread end mill .23
13.1 General .23
13.2 Necessary properties .23
13.3 Geometry of the non-cutting part inclusive of the connection .24
13.4 Geometry of the cutting part .24
13.5 Complete thread end mill .24
14 Cutting stylus .25
14.1 General .25
14.2 Necessary properties .25
14.3 Geometry of the non-cutting part inclusive of the connection .26
14.4 Geometry of the cutting part .
...
SPÉCIFICATION ISO/TS
TECHNIQUE 13399-303
Première édition
2016-02-01
Représentation et échange des
données relatives aux outils
coupants —
Partie 303:
Création et échange de modèles 3D
— Fraises cylindriques deux tailles
monobloc
Cutting tool data representation and exchange —
Part 303: Creation and exchange of 3D models — Solid end mills
Numéro de référence
©
ISO 2016
DOCUMENT PROTÉGÉ PAR COPYRIGHT
© ISO 2016
Tous droits réservés. Sauf prescription différente ou nécessité dans le contexte de sa mise en œuvre, aucune partie de cette
publication ne peut être reproduite ni utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique,
y compris la photocopie, ou la diffusion sur l’internet ou sur un intranet, sans autorisation écrite préalable. Une autorisation peut
être demandée à l’ISO à l’adresse ci-après ou au comité membre de l’ISO dans le pays du demandeur.
ISO copyright office
Case postale 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Genève
Tél.: +41 22 749 01 11
Fax: +41 22 749 09 47
E-mail: copyright@iso.org
Web: www.iso.org
Publié en Suisse
ii © ISO 2016 – Tous droits réservés
Sommaire Page
Avant-propos .v
Introduction .vii
1 Domaine d'application . 1
2 Références normatives . 1
3 Éléments de départ, systèmes de coordonnées, plans . 2
3.1 Généralités . 2
3.2 Système de référence . 2
3.3 Système de coordonnées sur la partie coupante . 3
3.4 Plans . 3
3.5 Point de coupe de référence (CRP) . 4
4 Conception du modèle . 5
4.1 Généralités . 5
4.2 Paramètres nécessaires pour la caractéristique d’interface de connexion. 5
5 Fraise cylindrique deux tailles non centrée . 5
5.1 Généralités . 5
5.2 Propriétés nécessaires . 6
5.3 Géométrie de la partie non-coupante, y compris le raccordement . 7
5.4 Géométrie de la partie coupante . 7
5.5 Fraise cylindrique deux tailles non centrée, complète . 8
6 Fraise cylindrique deux tailles centrée . 9
6.1 Généralités . 9
6.2 Propriétés nécessaires . 9
6.3 Géométrie de la partie non-coupante, y compris le raccordement . 9
6.4 Géométrie de la partie coupante .10
6.5 Fraise cylindrique deux tailles centrée, complète .10
7 Fraise cylindrique deux tailles angulaire (rainure en V) .11
7.1 Généralités .11
7.2 Propriétés nécessaires .11
7.3 Géométrie de la partie non-coupante, y compris le raccordement .12
7.4 Géométrie de la partie coupante .12
7.5 Fraise cylindrique deux tailles à rainure en V, complète .13
8 Fraise cylindrique deux tailles à queue d’aronde .13
8.1 Généralités .13
8.2 Propriétés nécessaires .14
8.3 Géométrie de la partie non-coupante, y compris le raccordement .14
8.4 Géométrie de la partie coupante .14
8.5 Fraise cylindrique deux tailles à queue d’aronde, complète .15
9 Fraise cylindrique deux tailles pour rainure à T .16
9.1 Généralités .16
9.2 Propriétés nécessaires .16
9.3 Géométrie de la partie non-coupante, y compris le raccordement .16
9.4 Géométrie de la partie coupante .16
9.5 Fraise cylindrique deux tailles pour rainure à T, complète .17
10 Fraise cylindrique deux tailles à bout sphérique .17
10.1 Généralités .17
10.2 Propriétés nécessaires .18
10.3 Géométrie de la partie non-coupante, y compris le raccordement .18
10.4 Géométrie de la partie coupante .18
10.5 Fraise cylindrique deux tailles à bout sphérique, complète .19
11 Fraise cylindrique deux tailles à matrice.19
11.1 Généralités .19
11.2 Propriétés nécessaires .20
11.3 Géométrie de la partie non-coupante, y compris le raccordement .20
11.4 Géométrie de la partie coupante .20
11.5 Fraise cylindrique deux tailles à matrice, complète .21
12 Fraise cylindrique deux tailles à profil arrondi concave .21
12.1 Généralités .21
12.2 Propriétés nécessaires .22
12.3 Géométrie de la partie non-coupante, y compris le raccordement .22
12.4 Géométrie de la partie coupante .22
12.5 Fraise cylindrique deux tailles à profil arrondi concave, complète .23
13 Fraise cylindrique deux tailles à fileter .23
13.1 Généralités .23
13.2 Propriétés nécessaires .24
13.3 Géométrie de la partie non-coupante, y compris le raccordement .24
13.4 Géométrie de la partie coupante .25
13.5 Fraise cylindrique deux tailles à fileter, complète .25
14 Burin à graver .26
14.1 Généralités .26
14.2 Propriétés nécessaires .26
14.3 Géométrie de la partie non-coupante, y compris le raccordement .26
14.4 Géométrie de la partie coupante .26
14.5 Burin à graver, complet .27
15 Fraise cylindrique deux tailles à fileter avec une partie forage .28
15.1 Généralités .28
15.2 Propriétés nécessaires .28
15.3 Géométrie de la partie non-coupante, y compris le raccordement .
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.