ISO 8102-1:2020

Electrical requirements for lifts, escalators and moving walks — Part 1: Electromagnetic compatibility with regard to emission

This document specifies the emission limits in relation to electromagnetic disturbances and test conditions for lifts, escalators and moving walks, which are intended to be permanently installed in buildings. It is possible, however, that these limits do not provide full protection against disturbances caused to radio and TV reception when such equipment is used within distances given in Table 1. This document is not applicable for apparatus which are manufactured before the date of its publication

Exigences électriques pour ascenseurs, escaliers mécaniques et trottoirs roulants — Partie 1: Compatibilité électromagnétique en ce qui concerne les émissions

General Information

• Status: Published
• Publication Date: 17-Jun-2020
• ICS: 91.140.90 - Lifts. Escalators
• Technical Committee: ISO/TC 178 - Lifts, escalators and moving walks
• Drafting Committee: ISO/TC 178/WG 8 - Electrical requirements
• Current Stage: 9092 - International Standard to be revised
• Completion Date: 17-Jan-2024

Relations

• Consolidated By: ISO 10304-4:2022 - Water quality — Determination of dissolved anions by liquid chromatography of ions — Part 4: Determination of chlorate, chloride and chlorite in water with low contamination
• Effective Date: 06-Jun-2022
• Revises: ISO 22199:2009 - Electromagnetic compatibility — Product family standard for lifts, escalators and moving walks — Emission
• Effective Date: 28-Jan-2017

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 8102-1
First edition
2020-06
Electrical requirements for lifts,
escalators and moving walks —
Part 1:
Electromagnetic compatibility with
regard to emission
Exigences électriques pour ascenseurs, escaliers mécaniques et
trottoirs roulants —
Partie 1: Compatibilité électromagnétique en ce qui concerne les
émissions
Reference number
ISO 8102-1:2020(E)
©
ISO 2020

---------------------- Page: 1 ----------------------
ISO 8102-1:2020(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2020
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: [phone]
Fax: [phone]
Email: [e-mail]
Website: www.iso.org
Published in Switzerland
ii © ISO 2020 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 8102-1:2020(E)

Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Test set-up procedure . 5
4.1 General . 5
4.2 Radiated and conducted radio-frequency emissions. 6
4.3 Voltage fluctuation and flicker . 6
4.4 Mains supply harmonics . 6
5 Applicability of tests . 6
6 Emission limits . 7
6.1 Enclosure ports (radiative) . 7
6.2 A.C. mains ports (conductive) . 7
6.3 Output power ports (conductive) . 7
6.4 Impulse noise . 7
6.5 Voltage fluctuations . 7
6.6 Mains supply current harmonics . 8
6.7 Measurement .
...

FINAL
INTERNATIONAL ISO/FDIS
DRAFT
STANDARD 8102-1
ISO/TC 178
Electrical requirements for lifts,
Secretariat: AFNOR
escalators and moving walks —
Voting begins on:
2020-03-26
Part 1:
Voting terminates on:
Electromagnetic compatibility with
2020-05-21
regard to emission
Exigences électriques pour ascenseurs, escaliers mécaniques et
trottoirs roulants —
Partie 1: Compatibilité électromagnétique en ce qui concerne les
émissions
RECIPIENTS OF THIS DRAFT ARE INVITED TO
SUBMIT, WITH THEIR COMMENTS, NOTIFICATION
OF ANY RELEVANT PATENT RIGHTS OF WHICH
THEY ARE AWARE AND TO PROVIDE SUPPOR TING
DOCUMENTATION.
IN ADDITION TO THEIR EVALUATION AS
Reference number
BEING ACCEPTABLE FOR INDUSTRIAL, TECHNO-
ISO/FDIS 8102-1:2020(E)
LOGICAL, COMMERCIAL AND USER PURPOSES,
DRAFT INTERNATIONAL STANDARDS MAY ON
OCCASION HAVE TO BE CONSIDERED IN THE
LIGHT OF THEIR POTENTIAL TO BECOME STAN-
DARDS TO WHICH REFERENCE MAY BE MADE IN
©
NATIONAL REGULATIONS. ISO 2020

---------------------- Page: 1 ----------------------
ISO/FDIS 8102-1:2020(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2020
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: [phone]
Fax: [phone]
Email: [e-mail]
Website: www.iso.org
Published in Switzerland
ii © ISO 2020 – All rights reserved

---------------------- Page: 2 ----------------------
ISO/FDIS 8102-1:2020(E)

Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Test set-up procedure . 5
4.1 General . 5
4.2 Radiated and conducted radio-frequency emissions. 6
4.3 Voltage fluctuation and flicker . 6
4.4 Mains supply harmonics . 6
5 Applicability of tests . 6
6 Emission limits . 7
6.1 Enclosure ports (radiative) . 7
6.2 A.C. mains ports (conductive) . 7
6.3 Output power ports (conductive) . 7
6.4 Impulse noise .
...