Cutting tool data representation and exchange — Part 311: Creation and exchange of 3D models — Solid reamers

ISO/TS 13399-311:2016 specifies a concept for the design of tool items, for all kinds of solid reamers, together with the usage of the related properties and domains of values. ISO/TS 13399-311:2016 specifies a common way of design simplified models that contain the following: - definitions and identifications of the design features of solid reamers, with an association to the used properties; - definitions and identifications of the internal structure of the 3D model that represents the features and the properties of solid reamers. The following are outside the scope of this part of ISO/TS 13399: - applications where these standard data may be stored or referenced; - concept of 3D models for cutting tools; - concept of 3D models for cutting items; - concept of 3D models for other tool items not being described in the scope of this part of ISO/TS 13399; - concept of 3D models for adaptive items; - concept of 3D models for assembly items and auxiliary items.

Représentation et échange des données relatives aux outils coupants — Partie 311: Création et échange des modèles 3D — Alésoirs monoblocs

La présente partie de l'ISO/TS 13399 spécifie un concept pour la conception des éléments relatifs aux outils, limité aux alésoirs monoblocs, utilisant les propriétés et domaines de valeurs associés. La présente partie de l'ISO/TS 13399 spécifie une façon commune de concevoir des modèles simplifiés contenant les éléments suivants: — des définitions et identifications des caractéristiques de conception des alésoirs monoblocs, avec un lien vers les propriétés utilisées; — des définitions et identifications de la structure interne du modèle 3D qui représente les caractéristiques et les propriétés des alésoirs monoblocs; Les éléments suivants n'entrent pas dans le domaine d'application de la présente partie de l'ISO/TS 13399: — les applications où les données standards peuvent être stockées ou référencées; — le concept de modèles 3D pour les outils coupants; — le concept de modèles 3D pour les éléments coupants; — le concept de modèles 3D pour d'autres éléments de l'outil non décrits dans le domaine d'application de la présente partie de l'ISO/TS 13399; — le concept de modèles 3D pour les éléments relatifs aux attachements; — le concept de modèles 3D pour les éléments relatifs aux assemblages et éléments auxiliaires.

General Information

Status
Published
Publication Date
03-Mar-2016
Current Stage
9020 - International Standard under periodical review
Start Date
15-Jul-2025
Completion Date
15-Jul-2025
Ref Project

Buy Standard

Technical specification
ISO/TS 13399-311:2016 - Cutting tool data representation and exchange
English language
24 pages
sale 15% off
Preview
sale 15% off
Preview
Technical specification
ISO/TS 13399-311:2016 - Cutting tool data representation and exchange
English language
24 pages
sale 15% off
Preview
sale 15% off
Preview
Technical specification
ISO/TS 13399-311:2016 - Représentation et échange des données relatives aux outils coupants
French language
25 pages
sale 15% off
Preview
sale 15% off
Preview
Technical specification
REDLINE ISO/TS 13399-311:2016 - Cutting tool data representation and exchange — Part 311: Creation and exchange of 3D models — Solid reamers Released:7/1/2019
French language
25 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)


TECHNICAL ISO/TS
SPECIFICATION 13399-311
First edition
Cutting tool data representation and
exchange —
Part 311:
Creation and exchange of 3D models
— Solid reamers
Représentation et échange des données relatives aux outils coupants —
Partie 311: Création et échange des modèles 3D — Alésoirs à arêtes
de coupe non amovibles
PROOF/ÉPREUVE
Reference number
ISO/TS 13399-311:2015(E)
©
ISO 2015
ISO/TS 13399-311:2015(E)
© ISO 2015, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2015 – All rights reserved

ISO/TS 13399-311:2015(E)
Contents Page
Foreword .v
Introduction .vii
1 Scope . 1
2 Normative references . 1
3 Starting elements, coordinate systems, planes . 2
3.1 General . 2
3.2 Reference system . 2
3.3 Primary coordinate system and mounting coordinate system . 2
3.4 Coordinate system at the cutting part . 3
3.5 Planes . 4
3.6 Cutting reference point . 5
4 Design of the model . 5
4.1 General . 5
4.2 Necessary properties for the connection interface feature . 6
5 Cylindrical reamer . 6
5.1 General . 6
5.2 Necessary properties . 7
5.3 Geometry of the non-cutting part including the connection . 7
5.4 Geometry of the cutting part . 8
5.5 Complete cylindrical reamer . 9
6 Tapered reamer . 9
6.1 General . 9
6.2 Necessary properties .10
6.3 Geometry of the non-cutting part including the connection .10
6.4 Geometry of the cutting part .10
6.5 Complete tapered reamer .11
7 Stepped reamer .11
7.1 General .11
7.2 Necessary properties .12
7.3 Geometry of the non-cutting part including the connection .13
7.4 Geometry of the cutting part .13
7.5 Complete stepped reamer .14
8 Bell-style reamer .15
8.1 General .15
8.2 Necessary properties .15
8.3 Geometry of the non-cutting part including the connection .16
8.4 Geometry of the cutting part .16
8.5 Complete bell-style reamer .17
9 Shell reamer .17
9.1 General .17
9.2 Necessary properties .18
9.3 Geometry of the non-cutting part including the connection .19
9.4 Geometry of the cutting part .19
9.5 Complete shell reamer .20
10 Design of details .21
10.1 Basics for modelling .21
10.2 Contact/clamping surfaces — Orientation .21
10.3 Chamfers and roundings .21
11 Attributes of surfaces — Visualization of the model features .21
ISO/TS 13399-311:2015(E)
12 Structure of the design elements (tree of model) .21
13 Data exchange model .22
Annex A (informative) Information about nominal dimensions .23
Bibliography .24
iv PROOF/ÉPREUVE © ISO 2015 – All rights reserved

ISO/TS 13399-311:2015(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity
assessment, as well as information about ISO’s adherence to the WTO principles in the Technical
Barriers to Trade (TBT), see the following URL: Foreword — Supplementary information.
The committee responsible for this document is ISO/TC 29, Small tools.
ISO/TS 13399 consists of the following parts, under the general title Cutting tool data representation
and exchange:
— Part 1: Overview, fundamental principles and general information model
— Part 2: Reference dictionary for the cutting items [Technical Specification]
— Part 3: Reference dictionary for tool items [Technical Specification]
— Part 4: Reference dictionary for adaptive items [Technical Specification]
— Part 5: Reference dictionary for assembly items [Technical Specification]
— Part 50: Reference dictionary for reference systems and common concepts [Technical Specification]
— Part 60: Reference dictionary for connection systems [Technical Specification]
— Part 80: Creation and exchange of 3D models — Overview and principles [Technical Specification]
— Part 100: Definitions, principles and methods for reference dictionaries [Technical Specification]
— Part 150: Usage guidelines [Technical Specification]
— Part 201: Creation and exchange of 3D models — Regular inserts [Technical Specification]
— Part 202: Creation and exchange of 3D models — Irregular inserts [Technical Specification]
— Part 203: Creation and exchange of 3D models — Replaceable inserts for drilling [Technical Specification]
— Part 204: Creation and exchange of 3D models — Inserts for reaming [Technical Specification]
— Part 301: Concept for the design of 3D models based on properties according to ISO/TS 13399-3:
Modelling of thread-cutting t
...


TECHNICAL ISO/TS
SPECIFICATION 13399-311
First edition
2016-03-01
Cutting tool data representation and
exchange —
Part 311:
Creation and exchange of 3D models
— Solid reamers
Représentation et échange des données relatives aux outils
coupants —
Partie 311: Création et échange des modèles 3D — Alésoirs à arêtes
de coupe non amovibles
Reference number
©
ISO 2016
© ISO 2016, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2016 – All rights reserved

Contents Page
Foreword .v
Introduction .vii
1 Scope . 1
2 Normative references . 1
3 Starting elements, coordinate systems, planes . 2
3.1 General . 2
3.2 Reference system . 2
3.3 Primary coordinate system and mounting coordinate system . 2
3.4 Coordinate system at the cutting part . 3
3.5 Planes . 4
3.6 Cutting reference point . 5
4 Design of the model . 5
4.1 General . 5
4.2 Necessary properties for the connection interface feature . 6
5 Cylindrical reamer . 6
5.1 General . 6
5.2 Necessary properties . 7
5.3 Geometry of the non-cutting part including the connection . 7
5.4 Geometry of the cutting part . 8
5.5 Complete cylindrical reamer . 9
6 Tapered reamer . 9
6.1 General . 9
6.2 Necessary properties .10
6.3 Geometry of the non-cutting part including the connection .10
6.4 Geometry of the cutting part .10
6.5 Complete tapered reamer .11
7 Stepped reamer .11
7.1 General .11
7.2 Necessary properties .12
7.3 Geometry of the non-cutting part including the connection .13
7.4 Geometry of the cutting part .13
7.5 Complete stepped reamer .14
8 Bell-style reamer .14
8.1 General .14
8.2 Necessary properties .15
8.3 Geometry of the non-cutting part including the connection .16
8.4 Geometry of the cutting part .16
8.5 Complete bell-style reamer .17
9 Shell reamer .17
9.1 General .17
9.2 Necessary properties .18
9.3 Geometry of the non-cutting part including the connection .18
9.4 Geometry of the cutting part .19
9.5 Complete shell reamer .20
10 Design of details .21
10.1 Basics for modelling .21
10.2 Contact/clamping surfaces — Orientation .21
10.3 Chamfers and roundings .21
11 Attributes of surfaces — Visualization of the model features .21
12 Structure of the design elements (tree of model) .21
13 Data exchange model .22
Annex A (informative) Information about nominal dimensions .23
Bibliography .24
iv © ISO 2016 – All rights reserved

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity
assessment, as well as information about ISO’s adherence to the WTO principles in the Technical
Barriers to Trade (TBT), see the following URL: Foreword — Supplementary information.
The committee responsible for this document is ISO/TC 29, Small tools.
ISO/TS 13399 consists of the following parts, under the general title Cutting tool data representation
and exchange:
— Part 1: Overview, fundamental principles and general information model
— Part 2: Reference dictionary for the cutting items [Technical Specification]
— Part 3: Reference dictionary for tool items [Technical Specification]
— Part 4: Reference dictionary for adaptive items [Technical Specification]
— Part 5: Reference dictionary for assembly items [Technical Specification]
— Part 50: Reference dictionary for reference systems and common concepts [Technical Specification]
— Part 60: Reference dictionary for connection systems [Technical Specification]
— Part 80: Creation and exchange of 3D models — Overview and principles [Technical Specification]
— Part 100: Definitions, principles and methods for reference dictionaries [Technical Specification]
— Part 150: Usage guidelines [Technical Specification]
— Part 201: Creation and exchange of 3D models — Regular inserts [Technical Specification]
— Part 202: Creation and exchange of 3D models — Irregular inserts [Technical Specification]
— Part 203: Creation and exchange of 3D models — Replaceable inserts for drilling [Technical Specification]
— Part 204: Creation and exchange of 3D models — Inserts for reaming [Technical Specification]
— Part 301: Concept for the design of 3D models based on properties according to ISO/TS 13399‑3: Modelling
of thread‑cutting taps, thread‑forming taps an
...


SPÉCIFICATION ISO/TS
TECHNIQUE 13399-311
Première édition
2016-03-01
Représentation et échange des
données relatives aux outils
coupants —
Partie 311:
Création et échange des modèles 3D —
Alésoirs monoblocs
Cutting tool data representation and exchange —
Part 311: Creation and exchange of 3D models — Solid reamers
Numéro de référence
©
ISO 2016
DOCUMENT PROTÉGÉ PAR COPYRIGHT
© ISO 2016
Tous droits réservés. Sauf prescription différente ou nécessité dans le contexte de sa mise en œuvre, aucune partie de cette
publication ne peut être reproduite ni utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique,
y compris la photocopie, ou la diffusion sur l’internet ou sur un intranet, sans autorisation écrite préalable. Une autorisation peut
être demandée à l’ISO à l’adresse ci-après ou au comité membre de l’ISO dans le pays du demandeur.
ISO copyright office
Case postale 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Genève
Tél.: +41 22 749 01 11
Fax: +41 22 749 09 47
E-mail: copyright@iso.org
Web: www.iso.org
Publié en Suisse
ii © ISO 2016 – Tous droits réservés

Sommaire Page
Avant-propos .v
Introduction .vii
1 Domaine d'application . 1
2 Références normatives . 1
3 Éléments de départ, systèmes de coordonnées, plans . 2
3.1 Généralités . 2
3.2 Système de référence . 2
3.3 Système de coordonnées principal et système de coordonnées de montage . 3
3.4 Système de coordonnées sur la partie coupante . 3
3.5 Plans . 4
3.6 Point de coupe de référence . 5
4 Conception du modèle . 6
4.1 Généralités . 6
4.2 Paramètres nécessaires pour la caractéristique d’interface de connexion. 6
5 Alésoir cylindrique . 7
5.1 Généralités . 7
5.2 Propriétés nécessaires . 7
5.3 Géométrie de la partie non-coupante, y compris le raccordement . 8
5.4 Géométrie de la partie coupante . 8
5.5 Alésoir cylindrique complet . 9
6 Alésoir conique .10
6.1 Généralités .10
6.2 Propriétés nécessaires .10
6.3 Géométrie de la partie non-coupante, y compris le raccordement .11
6.4 Géométrie de la partie coupante .11
6.5 Alésoir conique complet .12
7 Alésoir étagé .12
7.1 Généralités .12
7.2 Propriétés nécessaires .13
7.3 Géométrie de la partie non-coupante, y compris le raccordement .14
7.4 Géométrie de la partie coupante .14
7.5 Alésoir étagé complet .15
8 Alésoir en forme de cloche .15
8.1 Généralités .15
8.2 Propriétés nécessaires .16
8.3 Géométrie de la partie non-coupante, y compris le raccordement .17
8.4 Géométrie de la partie coupante .17
8.5 Alésoir en forme de cloche complet.18
9 Alésoir creux .18
9.1 Généralités .18
9.2 Propriétés nécessaires .19
9.3 Géométrie de la partie non-coupante, y compris le raccordement .20
9.4 Géométrie de la partie coupante .20
9.5 Alésoir creux complet .21
10 Conception des détails .22
10.1 Bases pour la modélisation .22
10.2 Surfaces de contact/serrage — Orientation .22
10.3 Chanfreins et arrondis .22
11 Attributs des surfaces — Visualisation des caractéristiques du modèle .22
12 Structure des éléments de conception (arborescence du modèle) .22
13 Modèle d’échanges de données .23
Annexe A (informative) Informations sur les dimensions nominales .24
Bibliographie .25
iv © ISO 2016 – Tous droits réservés

Avant-propos
L'ISO (Organisation internationale de normalisation) est une fédération mondiale d'organismes
nationaux de normalisation (comités membres de l'ISO). L'élaboration des Normes internationales est
en général confiée aux comités techniques de l'ISO. Chaque comité membre intéressé par une étude
a le droit de faire partie du comité technique créé à cet effet. Les organisations internationales,
gouvernementales et non gouvernementales, en liaison avec l'ISO participent également aux travaux.
L'ISO collabore étroitement avec la Commission électrotechnique internationale (IEC) en ce qui
concerne la normalisation électrotechnique.
Les procédures utilisées pour élaborer le présent document et celles destinées à sa mise à jour sont
décrites dans les Directives ISO/IEC, Partie 1. Il convient, en particulier de prendre note des différents
critères d'approbation requis pour les différents types de documents ISO. Le présent document a été
rédigé conformément aux règles de rédaction données dans les Directives ISO/IEC, Partie 2 (voir www
.iso .org/directives).
L'attention est appelée sur le fait que certains des éléments du présent document peuvent faire l'objet de
droits de propriété intellectuelle ou de droits analogues. L'ISO ne saurait être tenue pour responsable
de ne pas avoir identifié de tels droits de propriété et averti de leur existence. Les détails concernant
les références aux droits de propriété intellectuelle ou autres droits analogues identifiés lors de
l'élaboration du document sont indiqués dans l'Introduction et/ou dans la liste des déclarations de
brevets reçues par l’ISO (voir www .iso .org/brevets).
Les appellations commerciales éventuellement mentionnées dans le présent document sont données
pour information, par souci de commodité à l'intention des utilisateurs et ne sauraient constituer un
engagement.
Pour une explication de la signification des termes et expressions spécifiques de l'ISO liés à l'évaluation
de la conformité, ou pour toute information au sujet de l'adhésion de l'ISO aux principes de l'Organisation
mondiale du commerce (OMC) concernant les obstacles techniques au commerce (OTC) voir le lien
suivant: www .iso .org/iso/fr/foreword .html.
Le comité chargé de l'élaboration du présent document est l'ISO/TC 29, Petit outillage.
L'ISO 13399 comprend les parties suivantes, présentées sous le titre général Représentation et échange
des données relatives aux outils coupants:
— Partie 1: Vue d'ensemble, principes fondamentaux et modèle général d'informations
— Partie 2: Dictionnaire de référence pour les éléments coupants [Spécification technique]
— Partie 3: Dictionnaire de référence pour les éléments relatifs aux outils [Spécification technique]
— Partie 4: Dictionnaire de référence pour les éléments relatifs aux attachements [Spécification technique]
— Partie 5: Dictionnaire de référence pour les éléments d'assemblage [Spécification technique]
— Partie 50: Dictionnaire de référence pour les systèmes de référence et les concepts communs [Spécification
technique]
— Partie 60: Dictionnaire de référence pour les systèmes de connexion [Spécification technique]
— Partie 80: Création et échange des modèles 3D — Vue d'ensemble et principes [Spécification technique]
— Partie 100: Définitions, principes et méthodes pour les dictionnaires de référence [Spécification
technique]
— Partie 150: Lignes directrices d'utilisation [Spécification technique]
— Partie 201: Création et échange des modèles 3D — Plaquettes régulières [Spécification technique]
— Partie 202: Création et échange des modèles 3D — Plaquettes irrégulières [Spécification technique]
...


ISO/TC 29/SC
Date:  2016‐03‐01
ISO/TC 29/SC /GT 34
Secrétariat:  AFNOR
Représentation et échange des données relatives aux outils
coupants — Partie 311: Création et échange de modèles 3D — Alésoirs
monoblocs
Cutting tool data representation and exchange — Part 311: Creation and exchange of 3D models — Solid
reamers
Type du document: Spécification technique
Sous‐type du document:
Stade du document: (60) Publication
Langue du document: F
STD Version 2.9a
DOCUMENT PROTÉGÉ PAR COPYRIGHT
Droits de reproduction réservés. Sauf indication contraire, aucune partie de cette publication ne
peut être reproduite ni utilisée sous quelque forme que ce soit et par aucun procédé, électronique
ou mécanique, y compris la photocopie, l’affichage sur l’internet ou sur un Intranet, sans
autorisation écrite préalable. Les demandes d’autorisation peuvent être adressées à l’ISO à
l’adresse ci‐après ou au comité membre de l’ISO dans le pays du demandeur.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH‐1214 Vernier, Geneva, Switzerland
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
copyright@iso.org
www.iso.org
© ISO 2016 – Tous droits réservés
ii
Sommaire Page
Avant-propos v
Introduction viii
1 Domaine d'application . 1
2 Références normatives . 1
3 Eléments de départ, systèmes de coordonnées, plans . 2
3.1 Généralités . 2
3.2 Système de référence . 2
3.3 Système de coordonnées principal et système de coordonnées de montage . 3
3.4 Système de coordonnées sur la partie coupante . 3
3.5 Plans . 4
3.6 Point de coupe de référence . 5
4 Conception du modèle . 5
4.1 Généralités . 5
4.2 Paramètres nécessaires pour la caractéristique d’interface de connexion . 6
5 Alésoir cylindrique . 7
5.1 Généralités . 7
5.2 Propriétés nécessaires . 7
5.3 Géométrie de la partie non-coupante, y compris le raccordement . 8
5.4 Géométrie de la partie coupante . 8
5.5 Alésoir cylindrique complet . 9
6 Alésoir conique . 10
6.1 Généralités . 10
6.2 Propriétés nécessaires . 11
6.3 Géométrie de la partie non-coupante, y compris le raccordement . 11
6.4 Géométrie de la partie coupante . 11
6.5 Alésoir conique complet . 12
7 Alésoir étagé . 12
7.1 Généralités . 12
7.2 Propriétés nécessaires . 13
7.3 Géométrie de la partie non-coupante, y compris le raccordement . 14
7.4 Géométrie de la partie coupante . 14
7.5 Alésoir étagé complet . 15
8 Alésoir en forme de cloche . 16
8.1 Généralités . 16
8.2 Propriétés nécessaires . 16
8.3 Géométrie de la partie non-coupante, y compris le raccordement . 17
8.4 Géométrie de la partie coupante . 17
8.5 Alésoir en forme de cloche complet . 18
9 Alésoir creux . 18
9.1 Généralités . 18
9.2 Propriétés nécessaires . 19
9.3 Géométrie de la partie non-coupante, y compris le raccordement . 20
© ISO 2016 – Tous droits réservés
iii
9.4 Géométrie de la partie coupante . 20
9.5 Alésoir creux complet . 21
10 Conception des détails. 22
10.1 Bases pour la modélisation . 22
10.2 Surfaces de contact/serrage — Orientation . 22
10.3 Chanfreins et arrondis . 22
11 Attributs des surfaces — Visualisation des caractéristiques du modèle . 22
12 Structure des éléments de conception (arborescence du modèle). 22
13 Modèle d’échanges de données . 23
Annexe A (informative) Informations sur les dimensions nominales . 24
Bibliographie . 25

© ISO 2016 – Tous droits réservés
iv
Avant-propos
L'ISO (Organisation internationale de normalisation) est une fédération mondiale d'organismes
nationaux de normalisation (comités membres de l'ISO). L'élaboration des Normes internationales est
en général confiée aux comités techniques de l'ISO. Chaque comité membre intéressé par une étude a le
droit de faire partie du comité technique créé à cet effet. Les organisations internationales,
gouvernementales et non gouvernementales, en liaison avec l'ISO participent également aux travaux.
L'ISO collabore étroitement avec la Commission électrotechnique internationale (IEC) en ce qui
concerne la normalisation électrotechnique.
Les procédures utilisées pour élaborer le présent document et celles destinées à sa mise à jour sont
décrites dans les Directives ISO/IEC, Partie 1. Il convient, en particulier de prendre note des différents
critères d'approbation requis pour les différents types de documents ISO. Le présent document a été
rédigé conformément aux règles de rédaction données dans les Directives ISO/IEC, Partie 2
(voir www.iso.org/directives).
L'attention est appelée sur le fait que certains des éléments du présent document peuvent faire l'objet
de droits de propriété intellectuelle ou de droits analogues. L'ISO ne saurait être tenue pour
responsable de ne pas avoir identifié de tels droits de propriété et averti de leur existence. Les détails
concernant les références aux droits de propriété intellectuelle ou autres droits analogues identifiés
lors de l'élaboration du document sont indiqués dans l'Introduction et/ou dans la liste des déclarations
de brevets reçues par l’ISO (voir www.iso.org/brevets).
Les appellations commerciales éventuellement mentionnées dans le présent document sont données
pour information, par souci de commodité à l'intention des utilisateurs et ne sauraient constituer un
engagement.
Pour une explication de la signification des termes et expressions spécifiques de l'ISO liés à l'évaluation
de la conformité, ou pour toute information au sujet de l'adhésion de l'ISO aux principes de
l'Organisation mondiale du commerce (OMC) concernant les obstacles techniques au commerce (OTC)
voir le lien suivant: www.iso.org/iso/fr/foreword.html.
Le comité chargé de l'élaboration du présent document est l'ISO/TC 29, Petit outillage.
L'ISO 13399 comprend les parties suivantes, présentées sous le titre général Représentation et échange
Deleted:
des données relatives aux outils coupants:
Deleted:
— Partie 1: Vue d'ensemble, principes fondamentaux et modèle général d'informations Deleted:
— Partie 2: Dictionnaire de référence pour les éléments coupants [Spécification technique] Deleted:
— Partie 3: Dictionnaire de référence pour les éléments relatifs aux outils [Spécification technique]
Deleted:
— Partie 4: Dictionnaire de référence pour les éléments relatifs aux attachements [Spécification Deleted:
technique]
— Partie 5: Dictionnaire de référence pour les éléments d'assemblage [Spécification technique] Deleted:
— Partie 50: Dictionnaire de référence pour les systèmes de référence et les concepts communs Deleted:
[Spécification technique]
— Partie 60: Dictionnaire de référence pour les systèmes de connexion [Spécification technique]
Deleted:
© ISO 2016 – Tous droits réservés
v
— Partie 80: Création et échange des modèles 3D — Vue d'ensemble et principes [Spécification Deleted:
technique]
— Partie 100: Définitions, principes et méthodes pour les dictionnaires de référence [Spécification Deleted:
technique]
— Partie 150: Lignes directrices d'utilisation [Spécification technique] Deleted:
— Partie 201: Création et échange des modèles 3D — Plaquettes régulières [Spécification technique]
Deleted:
— Partie 202: Création et échange des modèles 3D — Plaquettes irrégulières [Spécification technique] Deleted:
— Partie 203: Création et échange des modèles 3D — Plaquettes de perçage échangeables [Spécification Deleted:
technique]
— Partie 204: Création et échange des modèles 3D — Plaquettes d'alésage [Spécification technique]
Deleted:
— Partie 301: Description des modèles 3D basés sur les propriétés de l'ISO/TS 13399-3: Modélisation des Deleted:
tarauds, tarauds à refouler et filières de filetage [Spécification technique]
Deleted: -
Deleted:
— Partie 302: Description des modèles 3D basés sur les propriétés de l'ISO/TS 13399-3: Modélisation des
Deleted:
forets monoblocs et des outils de lamage [Spécification technique]
Deleted:
— Partie 303: Description des modèles 3D basés sur les propriétés de l'ISO/TS 13399-3: Modélisation des
Deleted: -
fraises cylindriques à arêtes de coupe non amovibles [Spécification technique]
Deleted:
Deleted: -
— Partie 304: Description des modèles 3D basés sur les propriétés de l'ISO/TS 13399-3: Modélisation des
fraises à alésage et arêtes de coupe non amovibles [Spécification technique]
Deleted:
Deleted:
— Partie 307: Création et échange des modèles 3D — Fraises cylindriques pour plaquettes amovibles
Deleted: -
[Spécification technique]
Deleted:
— Partie 308: Création et échange des modèles 3D — Fraises à alésage pour plaquettes amovibles
Deleted:
[Spécification technique]
Deleted:
— Partie 309: Création et échange des modèles 3D — Porte-outils pour plaquettes amovibles Deleted:
[Spécification technique]
— Partie 311: Création et échange des modèles 3D — Alésoirs monoblocs [Spécification technique] Deleted:
— Partie 312: Création et échange des modèles 3D — Alésoirs pour plaquettes amo
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.