ISO 603-8:2024
(Main)Bonded abrasive products — Dimensions — Part 8: Grinding wheels for deburring and fettling/snagging on stationary machine
Bonded abrasive products — Dimensions — Part 8: Grinding wheels for deburring and fettling/snagging on stationary machine
This document specifies the nominal dimensions, in millimetres, of: — shape type 1: straight grinding wheel. These bonded abrasive products are intended to be used for deburring and fettling of any surface of a workpiece. The workpiece is manually guided, and the grinding wheel is fixed. This document does not specify limit deviations and run-out tolerances, which are given in ISO 13942.
Produits abrasifs agglomérés — Dimensions — Partie 8: Meules pour ébarbage et ébavurage sur une meuleuse stationnaire
Le présent document spécifie les dimensions nominales, en millimètres, de: — forme de type 1: meule plate. Ces produits abrasifs agglomérés sont destinés à être utilisés pour l'ébarbage et l'ébavurage de surfaces quelconques d'une pièce. La pièce est guidée manuellement et la meule est fixe. Le présent document ne spécifie pas les écarts limites et les tolérances de battement, qui sont donnés dans l'ISO 13942.
General Information
Relations
Buy Standard
Standards Content (Sample)
INTERNATIONAL ISO
STANDARD 603-8
Second edition
Bonded abrasive products —
Dimensions —
Part 8:
Grinding wheels for deburring and
fettling/snagging on stationary
machine
PROOF/ÉPREUVE
Reference number
ISO 603-8:2023(E)
© ISO 2023
---------------------- Page: 1 ----------------------
ISO 603-8:2023(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2023
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii
PROOF/ÉPREUVE © ISO 2023 – All rights reserved
---------------------- Page: 2 ----------------------
ISO 603-8:2023(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Shape type and dimensions.1
5 Designation . 2
Bibliography . 3
iii
© ISO 2023 – All rights reserved PROOF/ÉPREUVE
---------------------- Page: 3 ----------------------
ISO 603-8:2023(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO document should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
ISO draws attention to the possibility that the implementation of this document may involve the use
of (a) patent(s). ISO takes no position concerning the evidence, validity or applicability of any claimed
patent rights in respect thereof. As of the date of publication of this document, ISO had not received
notice of (a) patent(s) which may be required to implement this document. However, implementers are
cautioned that this may not represent the latest information, which may be obtained from the patent
database available at www.iso.org/patents. ISO shall not be held responsible for identifying any or all
such patent rights.
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to
the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see
www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 29, Small tools, Subcommittee SC 5,
Grin
...
© ISO 2023 – All rights reserved
ISO /PRF 603-8:2023(EN)
ISO /TC 29/SC 5/WG 5
2023-10-06
Secretariat: DIN
Date: 2023-11-24
Bonded abrasive products — Dimensions —
Part 8:
Grinding wheels for deburring and fettling/snagging on stationary
machine
PROOF
© ISO 2023 – All rights reserved
---------------------- Page: 1 ----------------------
ISO/PRF 603-8:2023(E)
© ISO 2023
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this
publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical,
including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can
be requested from either ISO at the address below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: + 41 22 749 01 11
Fax: +41 22 749 09 47
EmailE-mail: copyright@iso.org
Website: www.iso.orgwww.iso.org
Published in Switzerland
ii © ISO 2023 – All rights reserved
---------------------- Page: 2 ----------------------
ISO/PRF 603-8:2023(E)
Contents
Foreword . iv
Part 8: Grinding wheels for deburring and fettling/snagging on stationary machine . 1
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Shape type and dimensions . 1
5 Designation . 3
Bibliography . 4
Foreword iv
1 Scope 1
2 Normative references 1
3 Terms and definitions 1
4 Shape type and dimensions 1
5 Designation 3
Bibliography 4
© ISO 2023 – All rights reserved iii
---------------------- Page: 3 ----------------------
ISO/PRF 603-8:2023(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO
collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO document should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
ISO draws attention to the possibility that the implementation of this document may involve the use of
(a) patent(s). ISO takes no position concerning the evidence, validity or applicability of any claimed
patent rights in respect thereof. As of the date of publication of this document, ISO had not received notice
of (a) patent(s) which may be required to implement this document. However, implementers are
cautioned that this may not represent the latest information, which may be obtained from the patent
database available at www.iso.org/patents.www.iso.org/patents. ISO shall not be held responsible for
identifying any or all such patent rights.
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the World
Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see
w
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.