ISO 23717:2022
(Main)Steel wire and wire products — Hose reinforcement wire
Steel wire and wire products — Hose reinforcement wire
This document specifies the composition, dimensions and mechanical properties of steel wire with a high mass fraction of carbon, generally brass coated, for reinforcing high-pressure hoses. It is applicable to multiple parallel wires, braided or spirally wrapped for reinforcement in a rubber or synthetic hose that is made to withstand a relatively high bursting pressure.
Fils et produits tréfilés en acier — Fil d'armature pour flexibles
General Information
Relations
Standards Content (Sample)
INTERNATIONAL ISO
STANDARD 23717
Second edition
2022-03
Steel wire and wire products — Hose
reinforcement wire
Fils et produits tréfilés en acier — Fil d'armature pour flexibles
Reference number
ISO 23717:2022(E)
© ISO 2022
---------------------- Page: 1 ----------------------
ISO 23717:2022(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2022
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii
© ISO 2022 – All rights reserved
---------------------- Page: 2 ----------------------
ISO 23717:2022(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Classification . 2
5 Designation and ordering .2
5.1 Designation . 2
5.2 Information supplied by the purchaser and items to be agreed upon. 2
6 Requirements . 3
6.1 Material . 3
6.1.1 Steel . 3
6.1.2 Chemical composition . 3
6.1.3 Wire. 3
6.1.4 Coating material . 3
6.2 Mechanical properties . 3
6.2.1 Tensile strength, breaking load and elongation . 3
6.2.2 Reverse bend test . . 3
6.2.3 Torsion test . 3
6.3 Surface quality . 6
6.3.1 General . 6
6.3.2 Coating mass . 6
6.3.3 Cast and tip rise/dead cast . 6
6.4 Dimensions and tolerances . . . 6
6.4.1 Tolerance on diameter . 6
6.4.2 Out of roundness . 6
6.5 Delivery conditions . . 7
6.5.1 Unit package . 7
6.5.2 Welds . . 7
7 Testing and inspection .7
7.1 Testing and inspection documents . 7
7.2 Scope of test programme for acceptance inspection. 7
7.3 Test procedures . 7
7.3.1 Tensile test . 7
7.3.2 Reverse bend test and torsion test . 7
7.3.3 Diameter and out of roundness . 7
7.3.4 Cast and tip rise/dead cast . 8
7.3.5 Coating test . 8
7.4 Retests . 8
8 Marking, labelling and packaging .8
Annex A (informative) Packaging of hose reinforcement wire . 9
Bibliography .12
iii
© ISO 2022 – All rights reserved
---------------------- Page: 3 ----------------------
ISO 23717:2022(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to
the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see
www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 17, Steel, Subcommittee SC 17, Steel wire
rod and wire products.
This second edition cancels and replaces the first edition (ISO 23717:2006), which has been technically
revised.
The main changes are as follows:
— Annex A on packaging added;
— Clause 2 updated;
— Clause 3 updated;
— classification from LT to UT updated (see Clause 4);
— Cu content of coating updated (see 6.1.4);
— breaking load for mechanical properties added (see 6.2.1 and Table 1);
— product list and mechanical properties updated (see Table 1);
— cast and tip rise/dead cast requirement added (see 6.3.3 and Table 3);
— tolerance on diameter updated (see Table 4);
— welds requirement updated (see 6.5.2);
— test procedures for Cast and tip rise/dead cast and coating test added (see 7.3.4 and 7.3.5);
— labelling information for packing updated (see Table 5).
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www.iso.org/members.html.
iv
© ISO 2022 – All rights reserved
---------------------- Page: 4 ----------------------
ISO 23717:2022(E)
v
© ISO 2022 – All rights reserved
---------------------- Page: 5 ----------------------
INTERNATIONAL STANDARD ISO 23717:2022(E)
Steel wire and wire products — Hose reinforcement wire
1 Scope
This document specifies the composition, dimensions and mechanical properties of steel wire with a
high mass fraction of carbon, generally brass coated, for reinforcing high-pressure hoses.
It is applicable to multiple parallel wires, braided or spirally wrapped for reinforcement in a rubber or
synthetic hose that is made to withstand a relatively high bursting pressure.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 404, Steel and steel products — General technical delivery requirements
ISO 6892-1, Metallic materials — Tensile testing — Part 1: Method of test at room temperature
ISO 7800, Metallic materials — Wire — Simple torsion test
ISO 7801, Metallic materials — Wire — Reverse bend test
ISO 10474, Steel and steel products — Inspection documents
ISO 16120-1, Non-alloy steel wire rod for conversion to wire — Part 1: General requirements
ISO 16120-2, Non-alloy steel wire rod for conversion to wire — Part 2: Specific requirements for general
purpose wire rod
ISO 16120-4, Non-alloy steel wire rod for conversion to wire — Part 4: Specific requirements for wire rod
for special applications
ISO 23475-1, Testing method for steel tyre cord — Part 1: General requirements
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
ISO and IEC maintain terminology databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at https:// www .iso .org/ obp
— IEC Electropedia: available at https:// www .electropedia .org/
3.1
nominal diameter
d
value of the diameter by which the wire is designated and specified by the purchaser
Note 1 to entry: The nominal diameter is expressed in millimetres.
Note 2 to entry: This is the basis on which the values of all relevant characteristics are determined for the
acceptance of the wire.
1
© ISO 2022 – All rights reserved
---------------------- Page: 6 ----------------------
ISO 23717:2022(E)
3.2
out of roundness
arithmetic difference between the maximum and minimum diameter measured in a transverse cross-
section perpendicular to the wire axis
3.3
cast
smallest external diameter of a wire loops naturally formed when placed on a smooth surface without
external tension
3.4
tip rise/dead cast
vertical height of the cut wire end that protrudes above the flat and smooth surface, on which the wire
is placed without external tension
4 Classification
Hose wire is classified according to five classes of tensile strength.
— LT: Low
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.