Physical layer specifications and management parameters for 2.5 Gb/s and 5 Gb/s operation over backplane

Spécifications de la couche physique et paramètres de gestion pour fonctionnement à 2,5 Gb/s et 5 Gb/s sur fond de panier

General Information

Status
Published
Current Stage
5020 - FDIS ballot initiated: 2 months. Proof sent to secretariat
Start Date
24-Jun-2021
Completion Date
24-Jun-2021
Ref Project

RELATIONS

Buy Standard

Draft
ISO/IEC/IEEE 8802-3:2021/FDAmd 1 - Physical layer specifications and management parameters for 2.5 Gb/s and 5 Gb/s operation over backplane
English language
182 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (sample)

FINAL
ISO/IEC/IEEE
AMENDMENT
DRAFT
8802-3:2021
FDAM 1
ISO/IEC JTC 1/SC 6
Telecommunications and exchange
Secretariat: KATS
between information technology
Voting begins on:
2021-06-24 systems — Requirements for local and
metropolitan area networks —
Voting terminates on:
2021-11-11
Part 3:
Standard for Ethernet
AMENDMENT 1
Télécommunications et échange entre systèmes informatiques —
Exigences pour les réseaux locaux et métropolitains —
Partie 3: Norme pour Ethernet
AMENDEMENT 1
RECIPIENTS OF THIS DRAFT ARE INVITED TO
SUBMIT, WITH THEIR COMMENTS, NOTIFICATION
OF ANY RELEVANT PATENT RIGHTS OF WHICH
THEY ARE AWARE AND TO PROVIDE SUPPOR TING
DOCUMENTATION.
IN ADDITION TO THEIR EVALUATION AS
Reference number
BEING ACCEPTABLE FOR INDUSTRIAL, TECHNO-
ISO/IEC/IEEE 8802-3:2021/FDAM 1:2021(E)
LOGICAL, COMMERCIAL AND USER PURPOSES,
DRAFT INTERNATIONAL STANDARDS MAY ON
OCCASION HAVE TO BE CONSIDERED IN THE
LIGHT OF THEIR POTENTIAL TO BECOME STAN-
DARDS TO WHICH REFERENCE MAY BE MADE IN
NATIONAL REGULATIONS. IEEE 2019
---------------------- Page: 1 ----------------------
ISO/IEC/IEEE 8802-3:2021/FDAM 1:2021(E)
COPYRIGHT PROTECTED DOCUMENT
© IEEE 2019

All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may

be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting

on the internet or an intranet, without prior written permission. Permission can be requested from IEEE at the address below.

Institute of Electrical and Electronics Engineers, Inc
3 Park Avenue, New York
NY 10016-5997, USA
Email: stds.ipr@ieee.org
Website: www.ieee.org
Published in Switzerland
ii © IEEE 2019 – All rights reserved
---------------------- Page: 2 ----------------------
ISO/IEC/IEEE 8802-3:2021/FDAM 1:2021(E)
Foreword

ISO (the International Organization for Standardization) and IEC (the International Electrotechnical

Commission) form the specialized system for worldwide standardization. National bodies that are

members of ISO or IEC participate in the development of International Standards through technical

committees established by the respective organization to deal with particular fields of technical activity.

ISO and IEC technical committees collaborate in fields of mutual interest. Other international

organizations, governmental and non-governmental, in liaison with ISO and IEC, also take part in the

work.

The procedures used to develop this document and those intended for its further maintenance are

described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the

different types of ISO/IEC documents should be noted.

IEEE Standards documents are developed within the IEEE Societies and the Standards Coordinating

Committees of the IEEE Standards Association (IEEE-SA) Standards Board. The IEEE develops its

standards through a consensus development process, approved by the American National Standards

Institute, which brings together volunteers representing varied viewpoints and interests to achieve the

final product. Volunteers are not necessarily members of the Institute and serve without compensation.

While the IEEE administers the process and establishes rules to promote fairness in the consensus

development process, the IEEE does not independently evaluate, test, or verify the accuracy of any of the

information contained in its standards.

Attention is drawn to the possibility that some of the elements of this document may be the subject of

patent rights. ISO and IEC shall not be held responsible for identifying any or all such patent rights. Details

of any patent rights identified during the development of the document will be in the Introduction and/or

on the ISO list of patent declarations received (see www.iso.org/patents) or the IEC list of patent

declarations received (see patents.iec.ch).

Any trade name used in this document is information given for the convenience of users and does not

constitute an endorsement.

For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and

expressions related to conformity assessment, as well as information about ISO's adherence to the World

Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT),

see www.iso.org/iso/foreword.html. In the IEC, see www.iec.ch/understanding-standards.

ISO/IEC/IEEE 8802-3:2021/Amd.1 was prepared by the LAN/MAN of the IEEE Computer Society (as

IEEE Std 802.3cb-2018) and drafted in accordance with its editorial rules. It was adopted, under the “fast-

track procedure” defined in the Partner Standards Development Organization cooperation agreement

between ISO and IEEE, by Joint Technical Committee ISO/IEC JTC 1, Information technology,

Subcommittee SC 6, Telecommunications and information exchange between systems.

A list of all parts in the ISO/IEC/IEEE 8802 series can be found on the ISO and IEC websites.

Any feedback or questions on this document should be directed to the user’s national standards body. A

complete listing of these bodies can be found at www.iso.org/members.html and www.iec.ch/national-

committees.
© IEEE 2019 – All rights reserved iii
---------------------- Page: 3 ----------------------
IEEE Std 802.3cb™-2018
(Amendment to IEEE Std 802.3™-2018)
IEEE Standard for Ethernet
Amendment 1: 
Physical Layer Specifications 
and Management Parameters 
for 2.5 Gb/s and 5 Gb/s Operation 
over Backplane
Sponsor
LAN/MAN Standards Committee 
of the 
IEEE Computer Society
Approved 27 September 2018
IEEE-SA Standards Board
---------------------- Page: 4 ----------------------
ISO/IEC/IEEE 8802-3:2021/Amd.1:2021(E)

Abstract: Ethernet Media Access Control (MAC) parameters, Physical Layer specifications, and

management objects for the serial transfer of Ethernet format frames at 2.5 Gb/s and 5 Gb/s over

electrical backplanes are defined in this amendment to IEEE Std 802.3-2018.

Keywords: 2.5 Gigabit Ethernet, 5 Gigabit Ethernet, 2.5GBASE-KX, 2.5GBASE-X, 5GBASE-KR,

5GBASE-R, amendment, AN, Auto-Negotiation, Backplane Ethernet, BASE-R, BASE-X, EEE,

Energy Efficient Ethernet, Ethernet, IEEE 802.3™, IEEE 802.3cb™
The Institute of Electrical and Electronics Engineers, Inc.
3 Park Avenue, New York, NY 10016-5997, USA
Copyright © 2019 by The Institute of Electrical and Electronics Engineers, Inc.

All rights reserved. Published 4 January 2019. Printed in the United States of America.

IEEE and 802 are registered trademarks in the U.S. Patent & Trademark Office, owned by The Institute of Electrical and

Electronics Engineers, Incorporated.
PDF: ISBN 978-1-5044-5278-6 STD23391
Print: ISBN 978-1-5044-5279-3 STDPD23391
IEEE prohibits discrimination, harassment and bullying.

For more information, visit http://www.ieee.org/web/aboutus/whatis/policies/p9-26.html.

No part of this publication may be reproduced in any form, in an electronic retrieval system or otherwise, without the prior written permission

of the publisher.
---------------------- Page: 5 ----------------------
ISO/IEC/IEEE 8802-3:2021/Amd.1:2021(E)
Important Notices and Disclaimers Concerning IEEE Standards Documents

IEEE documents are made available for use subject to important notices and legal disclaimers. These notices and

disclaimers, or a reference to this page, appear in all standards and may be found under the heading “Important Notices

and Disclaimers Concerning IEEE Standards Documents.” They can also be obtained on request from IEEE or viewed at

http://standards.ieee.org/ipr/disclaimers.html.
Notice and Disclaimer of Liability Concerning the Use of IEEE Standards
Documents

IEEE Standards documents (standards, recommended practices, and guides), both full-use and trial-use, are developed

within IEEE Societies and the Standards Coordinating Committees of the IEEE Standards Association (“IEEE-SA”)

Standards Board. IEEE (“the Institute”) develops its standards through a consensus development process, approved by

the American National Standards Institute (“ANSI”), which brings together volunteers representing varied viewpoints

and interests to achieve the final product. IEEE Standards are documents developed through scientific, academic, and

industry-based technical working groups. Volunteers in IEEE working groups are not necessarily members of the

Institute and participate without compensation from IEEE. While IEEE administers the process and establishes rules to

promote fairness in the consensus development process, IEEE does not independently evaluate, test, or verify the

accuracy of any of the information or the soundness of any judgments contained in its standards.

IEEE Standards do not guarantee or ensure safety, security, health, or environmental protection, or ensure against

interference with or from other devices or networks. Implementers and users of IEEE Standards documents are

responsible for determining and complying with all appropriate safety, security, environmental, health, and interference

protection practices and all applicable laws and regulations.

IEEE does not warrant or represent the accuracy or content of the material contained in its standards, and expressly

disclaims all warranties (express, implied and statutory) not included in this or any other document relating to the

standard, including, but not limited to, the warranties of: merchantability; fitness for a particular purpose; non-

infringement; and quality, accuracy, effectiveness, currency, or completeness of material. In addition, IEEE disclaims

any and all conditions relating to: results; and workmanlike effort. IEEE standards documents are supplied “AS IS” and

“WITH ALL FAULTS.”

Use of an IEEE standard is wholly voluntary. The existence of an IEEE standard does not imply that there are no other

ways to produce, test, measure, purchase, market, or provide other goods and services related to the scope of the IEEE

standard. Furthermore, the viewpoint expressed at the time a standard is approved and issued is subject to change

brought about through developments in the state of the art and comments received from users of the standard.

In publishing and making its standards available, IEEE is not suggesting or rendering professional or other services for,

or on behalf of, any person or entity nor is IEEE undertaking to perform any duty owed by any other person or entity to

another. Any person utilizing any IEEE Standards document, should rely upon his or her own independent judgment in

the exercise of reasonable care in any given circumstances or, as appropriate, seek the advice of a competen t

professional in determining the appropriateness of a given IEEE standard.
IN NO EVENT SHALL IEEE BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,

EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO: PROCUREMENT OF

SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)

HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT

LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE

PUBLICATION, USE OF, OR RELIANCE UPON ANY STANDARD, EVEN IF ADVISED OF THE POSSIBILITY

OF SUCH DAMAGE AND REGARDLESS OF WHETHER SUCH DAMAGE WAS FORESEEABLE.
Translations

The IEEE consensus development process involves the review of documents in English only. In the event that an IEEE

standard is translated, only the English version published by IEEE should be considered the approved IEEE standard.

Copyright © 2019 IEEE. All rights reserved.
---------------------- Page: 6 ----------------------
ISO/IEC/IEEE 8802-3:2021/Amd.1:2021(E)
Official statements

A statement, written or oral, that is not processed in accordance with the IEEE-SA Standards Board Operations Manual

shall not be considered or inferred to be the official position of IEEE or any of its committees and shall not be considere d

to be, or be relied upon as, a formal position of IEEE. At lectures, symposia, seminars, or educational courses, a n

individual presenting information on IEEE standards shall make it clear that his or her views should be considered the

personal views of that individual rather than the formal position of IEEE.
Comments on standards

Comments for revision of IEEE Standards documents are welcome from any interested party, regardless of membership

affiliation with IEEE. However, IEEE does not provide consulting information or advice pertaining to IEEE Standards

documents. Suggestions for changes in documents should be in the form of a proposed change of text, together with

appropriate supporting comments. Since IEEE standards represent a consensus of concerned interests, it is important that

any responses to comments and questions also receive the concurrence of a balance of interests. For this reason, IEEE

and the members of its societies and Standards Coordinating Committees are not able to provide an instant response to

comments or questions except in those cases where the matter has previously been addressed. For the same reason, IEE E

does not respond to interpretation requests. Any person who would like to participate in revisions to an IEEE standard is

welcome to join the relevant IEEE working group.
Comments on standards should be submitted to the following address:
Secretary, IEEE-SA Standards Board 
445 Hoes Lane 
Piscataway, NJ 08854 USA
Laws and regulations

Users of IEEE Standards documents should consult all applicable laws and regulations. Compliance with the provisions

of any IEEE Standards document does not imply compliance to any applicable regulatory requirements. Implementers of

the standard are responsible for observing or referring to the applicable regulatory requirements. IEEE does not, by the

publication of its standards, intend to urge action that is not in compliance with applicable laws, and these documents

may not be construed as doing so.
Copyrights

IEEE draft and approved standards are copyrighted by IEEE under U.S. and international copyright laws. They are made

available by IEEE and are adopted for a wide variety of both public and private uses. These include both use, by

reference, in laws and regulations, and use in private self-regulation, standardization, and the promotion of engineering

practices and methods. By making these documents available for use and adoption by public authorities and private

users, IEEE does not waive any rights in copyright to the documents.
Photocopies

Subject to payment of the appropriate fee, IEEE will grant users a limited, non-exclusive license to photocopy portions

of any individual standard for company or organizational internal use or individual, non-commercial use only. T o

arrange for payment of licensing fees, please contact Copyright Clearance Center, Customer Service, 222 Rosewood

Drive, Danvers, MA 01923 USA; +1 978 750 8400. Permission to photocopy portions of any individual standard for

educational classroom use can also be obtained through the Copyright Clearance Center.

Copyright © 2019 IEEE. All rights reserved.
---------------------- Page: 7 ----------------------
ISO/IEC/IEEE 8802-3:2021/Amd.1:2021(E)
Updating of IEEE Standards documents

Users of IEEE Standards documents should be aware that these documents may be superseded at any time by the

issuance of new editions or may be amended from time to time through the issuance of amendments, corrigenda, or

errata. An official IEEE document at any point in time consists of the current edition of the document together with any

amendments, corrigenda, or errata then in effect.

Every IEEE standard is subjected to review at least every ten years. When a document is more than ten years old and has

not undergone a revision process, it is reasonable to conclude that its contents, although still of some value, do no t

wholly reflect the present state of the art. Users are cautioned to check to determine that they have the latest edition of

any IEEE standard.

In order to determine whether a given document is the current edition and whether it has been amended through the

issuance of amendments, corrigenda, or errata, visit the IEEE-SA Website at http://ieeexplore.ieee.org or contact IEEE

at the address listed previously. For more information about the IEEE SA or IEEE’s standards development process, visit

the IEEE-SA Website at http://standards.ieee.org.
Errata

Errata, if any, for all IEEE standards can be accessed on the IEEE-SA Website at the following URL :

http://standards.ieee.org/findstds/errata/index.html. Users are encouraged to check this URL for errata periodically.

Patents

Attention is called to the possibility that implementation of this standard may require use of subject matter covered by

patent rights. By publication of this standard, no position is taken by the IEEE with respect to the existence or validity o f

any patent rights in connection therewith. If a patent holder or patent applicant has filed a statement of assurance via an

Accepted Letter of Assurance, then the statement is listed on the IEEE-SA Website a t

http://standards.ieee.org/about/sasb/patcom/patents.html. Letters of Assurance may indicate whether the Submitter is

willing or unwilling to grant licenses under patent rights without compensation or under reasonable rates, wit h

reasonable terms and conditions that are demonstrably free of any unfair discrimination to applicants desiring to obtai n

such licenses.

Essential Patent Claims may exist for which a Letter of Assurance has not been received. The IEEE is not responsible for

identifying Essential Patent Claims for which a license may be required, for conducting inquiries into the legal validity

or scope of Patents Claims, or determining whether any licensing terms or conditions provided in connection with

submission of a Letter of Assurance, if any, or in any licensing agreements are reasonable or non-discriminatory. Users

of this standard are expressly advised that determination of the validity of any patent rights, and the risk of infringemen t

of such rights, is entirely their own responsibility. Further information may be obtained from the IEEE Standards

Association.
Copyright © 2019 IEEE. All rights reserved.
---------------------- Page: 8 ----------------------
ISO/IEC/IEEE 8802-3:2021/Amd.1:2021(E)
Participants

The following individuals were officers and members of the IEEE 802.3 Working Group at the beginning of

the IEEE P802.3cb Working Group ballot.
David J. Law, IEEE 802.3 Working Group Chair
Adam Healey, IEEE 802.3 Working Group Vice-Chair
Peter Anslow, IEEE 802.3 Working Group Secretary
Steven B. Carlson, IEEE 802.3 Working Group Executive Secretary
Valerie Maguire, IEEE 802.3 Working Group Treasurer
Yong Kim, IEEE P802.3cb Task Force Chair, Phase 1*
Daniel F. Smith, IEEE P802.3cb Task Force Chair, Phase 2
William Lo, IEEE P802.3cb Task Force Editor-in-Chief, Phase 1
Daniel F. Smith, IEEE P802.3cb Task Force Editor-in-Chief, Phase 2
Jim Hatfield, IEEE P802.3cb Task Force Editor, Phase 2*
John Dillard Upen Kareti
Justin Abbott
David Abramson Daniel Dillow Keisuke Kawahara
Shadi Abughazaleh Thuyen Dinh Yasuaki Kawatsu
Mohammad Ahmed Curtis Donahue Michael Kelsen
Scott Kipp
Eric Baden Dan Dove
Michael Klempa
Amrik Bains Mike Dudek
Curtis Knittle
Thananya Baldwin David Dwelley
Shigeru Kobayashi
Denis Beaudoin Frank Effenberger
Daniel Koehler
Christian Beia Hesham Elbakoury
Paul Kolesar
Michael Bennett David Estes
Tom Kolze
Vipul Bhatt John Ewen
Glen Kramer
William Bliss Ramin Farjad
Hans Lackner
Brad Booth Shahar Feldman
Jeffrey Lapak
Martin Bouda James Fife
Mark Laubach
Ralf-Peter Braun Alan Flatman
Han Hyub Lee
Theodore Brillhart Matthias Fritsche
David Lewis
Paul Brooks Richard Frosch
Jon Lewis
Alan Brown Andrew Gardner
Mike Peng Li
Matthew Brown Claude Gauthier
Jane Lim
Chris Bullock Ali Ghiasi
Dekun Liu
Jairo Bustos Heredia Joel Goergen
Hai-Feng Liu
Adrian Butter Volker Goetzfried
Miklos Lukacs
Francesco Caggioni Zhigang Gong
Kent Lusted
Anthony Calbone Steven Gorshe
Jeffery Maki
Clark Carty Robert Grow
David Malicoat
Mark Gustlin
Craig Chabot
Yonatan Malkiman
Marek Hajduczenia
Geoffrey Chacon Simon
Arthur Marris
Takehiro Hayashi
Mandeep Chadha
Takeo Masuda
David Chalupsky Yasuo Hidaka
Erdem Matoglu
Jacky Chang Rita Horner
Naoki Matsuda
Xin Chang Bernd Horrmeyer
Mick McCarthy
Ahmad Chini Victor Hou
Brett McClellan
Keng Hua Chuang Yasuhiro Hyakutake
Thomas McDermott
Christopher R. Cole Hideki Isono
John McDonough
John D'Ambrosia Tom Issenhuth
Larry McMillan
Yair Darshan Kenneth Jackson
Richard Mei
Piers Dawe Andrew Jimenez
Richard Mellitz
Fred Dawson Chad Jones
Bryan Moffitt
Wael Diab Peter Jones
Ardeshir Mohammadian
Eric DiBiaso Manabu Kagami
Paul Mooney

* Not a member of the IEEE 802.3 working group at the beginning of the working group ballot.

Copyright © 2019 IEEE. All rights reserved.
---------------------- Page: 9 ----------------------
ISO/IEC/IEEE 8802-3:2021/Amd.1:2021(E)
Dale Murray Sam Sambasivan Pirooz Tooyserkani
Henry Muyshondt Edward Sayre Albert Tretter
James Nadolny Dieter Schicketanz Stephen Trowbridge
Edward Nakamoto Fred Schindler
Yoshihiro Tsukamoto
Gary Nicholl Hossein Sedarat
Ed Ulrichs
Kevin Noll Naoshi Serizawa
Alexander Umnov
Mark Nowell Masood Shariff
Sterling A. Vaden
Ramin Shirani
David Ofelt Stefano Valle
Tom Skaar
Thomas Palkert Paul Vanderlaan
Jeff Slavick
Hui Pan Robert Wagner
Sesha Panguluri Scott Sommers Dylan Walker
Vasu Parthasarathy Yoshiaki Sone Haifei Wang
Petar Pepeljugoski Tom Souvignier Roy Wang
Gerald Pepper Peter Stassar Tongtong Wang
Ruben Perez De Aranda Alonso Heath Stewart Xinyuan Wang
Michael Peters Robert Stone Matthias Wendt
Phong Pham David Stover Oded Wertheim
Jean Picard Junqing Sun Natalie Wienckowski
William Powell Ken-Ichi Suzuki Ludwig Winkel
Rick Rabinovich Steve Swanson Peter Wu
Adee Ran Andre Szczepanek Dayin Xu
Alon Regev William Szeto Yu Xu
Duane Remein Bharat Tailor Jun Yi
Victor Renteria Takayuki Tajima Lennart Yseboodt
Christopher Roth Satoshi Takahashi Hayato Yuki
Salvatore Rotolo Kohichi Tamura Andrew Zambell
Toshiaki Sakai Brian Teipen Yan Zhuang
Jorge Salinger Geoffrey Thompson George Zimmerman

The following members of the individual balloting committee voted on this amendment. Balloters may have

voted for approval, disapproval, or abstention.
Shadi Abughazaleh Marco Hernandez Thomas Palkert
David Hess Bansi Patel
Thomas Alexander
Peter Anslow Werner Hoelzl Arumugam Paventhan
Butch Anton Rita Horner Michael Peters
Amrik Bains C. Huntley Rick Pimpinella
Noriyuki Ikeuchi Adee Ran
Ralf-Peter Braun
Nancy Bravin Atsushi Ito Alon Regev
Theodore Brillhart Raj Jain Maximilian Riegel
Matthew Brown SangKwon Jeong Robert Robinson
Piotr Karocki Benjamin Rolfe
Demetrio Bucaneg
Jairo Bustos Heredia Stuart Kerry Daniel F. Smith
William Byrd Yong Kim Thomas Starai
Steven B. Carlson Mark Laubach Walter Struppler
David J. Law
Juan Carreon Mitsutoshi Sugawara
Mandeep Chadha Jon Lewis Junqing Sun
Keith Chow Mike Peng Li Geoffrey Thompson
Keng Hua Chuang Elvis Maculuba Michael Thompson
Steven Tilden
Charles Cook Valerie Maguire
Rodney Cummings Jeffery Maki David Tremblay
Sourav Dutta Arthur Marris Mark-Rene Uchida
Michael Fischer Mick McCarthy Alexander Umnov
Matthias Fritsche Brett McClellan Paul Vanderlaan
Yukihiro Fujimoto Thomas McDermott George Vlantis
Zhigang Gong Larry McMillan Khurram Waheed
James Graba Richard Mellitz Lisa Ward
Eric W. Gray Charles Moorwood Karl Weber
Randall Groves Michael Newman Andreas Wolf
Robert Grow Nick S. A. Nikjoo Peter Wu
Michael Gundlach Paul Nikolich Jun Xu
Marek Hajduczenia Satoshi Obara Oren Yuen
Adam Healey Zhen Zhou
Copyright © 2019 IEEE. All rights reserved.
---------------------- Page: 10 ----------------------
ISO/IEC/IEEE 8802-3:2021/Amd.1:2021(E)

When the IEEE-SA Standards Board approved this amendment on 27 September 2018, it had the following

membership:
Jean-Philippe Faure, Chair
Gary Hoffman, Vice Chair
John D. Kulick, Past Chair
Konstantinos Karachalios, Secretary
Ted Burse
Xiaohui Liu Robby Robson
Guido R. Hiertz Kevin Lu Dorothy Stanley
Christel Hunter Daleep Mohla Mehmet Ulema
Joseph L. Koepfinger* Andrew Myles Phil Wennblom
Thomas Koshy Paul Nikolich Philip Winston
Howard Wolfman
Hung Ling Ronald C. Petersen
Annette D. Reilly Jingyi Zhou
Dong Liu
*Member Emeritus
Copyright © 2019 IEEE. All rights reserved.
---------------------- Page: 11 ----------------------
ISO/IEC/IEEE 8802-3:2021/Amd.1:2021(E)
Introduction

This introduction is not part of IEEE Std 802.3cb-2018, IEEE Standard for Ethernet—Amendment 1: Physical Laye r

Specifications and Management Parameters for 2.5 Gb/s and 5 Gb/s Operation over Backplane.

IEEE Std 802.3™ was first published in 1985. Since the initial publication, many projects have added

functionality or provided maintenance updates to the specifications and text included in the standard. Each

IEEE 802.3 project/amendment is identified with a suffix (e.g., IEEE Std 802.3ba™-2010).

The half duplex Media Access Control (MAC) protocol specified in IEEE Std 802.3-1985 is Carrier Sense

Multiple Access with Collision Detection (CSMA/CD). This MAC protocol was key to the experimental

Ethernet developed at Xerox Palo Alto Research Center, which had a 2.94 Mb/s data rate. Ethernet at

10 Mb/s was jointly released as a public specification by Digital Equipment Corporation (DEC), Intel and

Xerox in 1980. Ethernet at 10 Mb/s was approved as an IEEE standard by the IEEE Standards Board in 1983

and subsequently published in 1985 as IEEE Std 802.3-1985. Since 1985, new media options, new speeds o f

operation, and new capabilities have been added to IEEE Std 802.3. A full duplex MAC protocol was added

in 1997.

Some of the major additions to IEEE Std 802.3 are identified in the marketplace with their project number.

This is most common for projects adding higher speeds of operation or new protocols. For example,

IEEE Std 802.3u™ added 100 Mb/s operation (also called Fast Ethernet), IEEE Std 802.3z added 1000 Mb/s

operation (also called Gigabit Ethernet), IEEE Std 802.3ae added 10 Gb/s operation (also called 10 Gigabit

Ethernet), IEEE Std 802.3ah™ specified access network Ethernet (also called Ethernet in the First Mile) and

IEEE Std 802.3ba added 40 Gb/s operation (also called 40 Gigabit Ethernet) and 100 Gb/s operation (also

called 100 Gigabit Ethernet). These major additions are all now included in and are superseded by

IEEE Std 802.3-2018 and are not maintained as separate documents.

At the date of publication for IEEE Std 802.3cb-2018, IEEE Std 802.3 was composed of the following

documents:
IEEE Std 802.3-2018

Section One—Includes Clause 1 through Clause 20 and Annex A through Annex H and Annex 4A.

Section One includes the specifications for 10 Mb/s operation and the MAC, frame formats and servic e

interfaces used for all speeds of operation.

Section Two—Includes Clause 21 through Clause 33 and Annex 22A through Annex 33E. Section

Two includes management attributes for multiple protocols and speed of operation as well as

specifications for providing power over twisted pair cabling for multiple operational speeds. It also

includes general information on 100 Mb/s operation as well as most of the 100 Mb/s Physical Layer

specifications.

Section Three—Includes Clause 34 through Clause 43 and Annex 36A through Annex 43C. Sectio n

Three includes general information on 1000 Mb/s operation as well as most of the 1000 Mb/s Physical

Layer specifications.

Section Four—Includes Clause 44 through Clause 55 and Annex 44A through Annex 55B. Sectio n

Four includes general information on 10 Gb/s operation as well as most of the 10 Gb/s Physical Layer

specifications.

Section Five—Includes Clause 56 through Clause 77 and Annex 57A through Annex 76A. Clause 56

through Clause 67 and Clause 75 through Clause 77, as well as associated annexes, specify subscriber

access and other Physical Layers and sublayers for operation from 512 kb/s to 10 Gb/s, and defines

Copyright © 2019 IEEE. All rights reserved.
---------------------- Page: 12 ----------------------
ISO/IEC/IEEE 8802-3:2021/Amd.1:2021(E)

services and protocol elements that enable the exchange of IEEE Std 802.3 format frames between

stations in a subscriber access network. Clause 68 specifies a 10 Gb/s Physical Layer specification.

Clause 69 through Clause 74 and associated annexes specify Ethernet operation over electrical

backplanes at speeds of 1000 Mb/s and 10 Gb/s.

Section Six—Includes Clause 78 through Clause 95 and Annex 83A through Annex 93C. Clause 78

specifies Energy-Efficient Ethernet. Clause 79 specifies IEEE 802.3 Organizationally Specific Link

Layer Discovery Protocol (LLDP) type, length, and value (TLV) information elements. Clause 80

through Clause 95 and associated annexes includes general information on 40 Gb/s and 100 Gb/s

operation as well the 40 Gb/s and 100 Gb/s Physical Layer specifications. Clause 90 specifies Ethernet

support for time synchronization protocols.

Section Seven—Includes Clause 96 through Clause 115 and Annex 97A through Annex 115A.

Clause 96 through Clause 98, Clause 104, and associated annexes, specify Physical Layers and

optional features for 100 Mb/s and 1000 Mb/s operation over a single twisted pair. Clause 100 throug h

Clause 103, as well as associated annexes, specify Physical Layers for the operation of the EPON

protocol over coaxial distribution networks. Clause 105 through Clause 114 and associated annexes

include general information on 25 Gb/s operation as well as 25 Gb/s Physical Layer specifications.

Clause 99 specifies a MAC merge sublayer for the interspersing of express traffic. Clause 115 and its

associated annex specify a Physical Layer for 1000 Mb/s operation over plastic optical fiber.

Section Eight—Includes Clause 116 through Clause 126 a
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.