Petroleum and natural gas industries — Steel drill pipe

This document specifies the technical delivery conditions for steel drill-pipes with upset pipe-body ends and weld-on tool joints for use in drilling and production operations in petroleum and natural gas industries for three product specification levels (PSL-1, PSL-2 and PSL-3). The requirements for PSL-1 form the basis of this document. The requirements that define different levels of standard technical requirements for PSL-2 and PSL-3 are in Annex G. This document covers the following grades of drill-pipe: — grade E drill-pipe; — high-strength grades of drill-pipe, grades X, G and S; — enhanced H2S resistance drill pipe, grades D and F. A typical drill-pipe configuration is given, showing main elements and lengths (see Figure B.1). The main dimensions and masses of the grades of drill-pipe are given in both SI units (see Table A.1) and in USC units (see Table C.1). This document can also be used for drill-pipe with tool joints not specified by ISO or API standards. By agreement between purchaser and manufacturer, this document can also be applied to other drill-pipe body and/or tool-joint dimensions. This document lists supplementary requirements that can optionally be agreed between purchaser and manufacturer, for testing, performance verification and non-destructive examination (see Annex E). This document does not consider performance properties, nor performance degradation of the product when in service. NOTE 1 In this document, drill-pipe is designated by label 1, label 2, grade of material (E, X, G, S, D and F), upset type and type of rotary shouldered connection. Designations are used for the purpose of identification in ordering. NOTE 2 Reference can be made to ISO 10424-2 or API Spec 7-2 for the detailed requirements for the threading of drill-pipe tool joints. NOTE 3 Reference can be made to API RP 7G for the performance properties of the drill-pipe.

Industries du pétrole et du gaz naturel — Tiges de forage en acier

General Information

Status
Published
Publication Date
16-Oct-2018
Current Stage
9093 - International Standard confirmed
Completion Date
12-Jun-2024
Ref Project

Relations

Buy Standard

Standard
ISO 11961:2018 - Petroleum and natural gas industries — Steel drill pipe Released:17. 10. 2018
English language
108 pages
sale 15% off
Preview
sale 15% off
Preview
Standard
ISO 11961:2018 - Petroleum and natural gas industries -- Steel drill pipe
English language
108 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 11961
Third edition
2018-10
Petroleum and natural gas
industries — Steel drill pipe
Industries du pétrole et du gaz naturel — Tiges de forage en acier
Reference number
ISO 11961:2018(E)
©
ISO 2018

---------------------- Page: 1 ----------------------
ISO 11961:2018(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2018
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2018 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 11961:2018(E)

Contents Page
Foreword .viii
Introduction .ix
1 Scope . 1
2 Normative references . 1
3 Terms, definitions, symbols and abbreviated terms . 2
3.1 Terms and definitions . 2
3.2 Symbols and abbreviated terms. 7
4 Conformance . 9
4.1 Dual citing of normative references . 9
4.2 Units of measurement . . 9
5 Information to be supplied when placing orders for drill-pipe . 9
5.1 Grades D95 and F105 . 9
5.2 General information .10
5.3 Additional information .10
6 Requirements for drill-pipe .11
6.1 General .11
6.2 Dimensions, masses and connections .11
6.2.1 Standard configuration.11
6.2.2 Alternative configurations .12
6.2.3 Drill-pipe weld neck diameters .12
6.2.4 Tool-joint inside diameter
...

INTERNATIONAL ISO
STANDARD 11961
Third edition
2018-10
Petroleum and natural gas
industries — Steel drill pipe
Industries du pétrole et du gaz naturel — Tiges de forage en acier
Reference number
ISO 11961:2018(E)
©
ISO 2018

---------------------- Page: 1 ----------------------
ISO 11961:2018(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2018
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2018 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 11961:2018(E)

Contents Page
Foreword .viii
Introduction .ix
1 Scope . 1
2 Normative references . 1
3 Terms, definitions, symbols and abbreviated terms . 2
3.1 Terms and definitions . 2
3.2 Symbols and abbreviated terms. 7
4 Conformance . 9
4.1 Dual citing of normative references . 9
4.2 Units of measurement . . 9
5 Information to be supplied when placing orders for drill-pipe . 9
5.1 Grades D95 and F105 . 9
5.2 General information .10
5.3 Additional information .10
6 Requirements for drill-pipe .11
6.1 General .11
6.2 Dimensions, masses and connections .11
6.2.1 Standard configuration.11
6.2.2 Alternative configurations .12
6.2.3 Drill-pipe weld neck diameters .12
6.2.4 Tool-joint inside diameter
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.