ISO 14624-3:2023

Space systems — Safety and compatibility of materials — Part 3: Determination of off-gassed compounds from materials and assembled articles

This document specifies a method for determining the identity and quantity of volatile off-gassed compounds from materials and assembled articles utilized in manned, pressurized spacecraft.

Systèmes spatiaux — Sécurité et compatibilité des matériaux — Partie 3: Détermination des composés issus du dégazage sous atmosphère des matériaux et des articles assemblés

General Information

• Status: Published
• Publication Date: 09-Oct-2023
• ICS: 49.025.01 - Materials for aerospace construction in general
• ICS: 49.140 - Space systems and operations
• Technical Committee: ISO/TC 20/SC 14 - Space systems and operations
• Drafting Committee: ISO/TC 20/SC 14 - Space systems and operations
• Current Stage: 6060 - International Standard published
• Start Date: 10-Oct-2023
• Due Date: 20-May-2023
• Completion Date: 10-Oct-2023

Relations

• Revises: ISO 14624-3:2005 - Space systems — Safety and compatibility of materials — Part 3: Determination of offgassed products from materials and assembled articles
• Effective Date: 06-Jun-2022

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 14624-3
Second edition
2023-10
Space systems — Safety and
compatibility of materials —
Part 3:
Determination of off-gassed
compounds from materials and
assembled articles
Systèmes spatiaux — Sécurité et compatibilité des matériaux —
Partie 3: Détermination des composés issus du dégazage sous
atmosphère des matériaux et des articles assemblés
Reference number
ISO 14624-3:2023(E)
© ISO 2023

---------------------- Page: 1 ----------------------
ISO 14624-3:2023(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2023
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: [phone]
Email: [e-mail]
Website: www.iso.org
Published in Switzerland
ii
  © ISO 2023 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 14624-3:2023(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Principle . 3
5 Health and safety of test operators . 3
6 Test conditions .3
7 Apparatus and materials .4
8 Test samples .5
8.1 Handling/receipt . 5
8.2 Preparation . 5
8.3 Cleaning . 6
8.4 Inspection . 6
9 Pretest procedure .6
10 Test procedure .6
11 Precision . 7
12 Test r
...

FINAL
INTERNATIONAL ISO/FDIS
DRAFT
STANDARD 14624-3
ISO/TC 20/SC 14
Space systems — Safety and
Secretariat: ANSI
compatibility of materials —
Voting begins on:
2023-07-10
Part 3:
Voting terminates on:
Determination of off-gassed
2023-09-04
compounds from materials and
assembled articles
RECIPIENTS OF THIS DRAFT ARE INVITED TO
SUBMIT, WITH THEIR COMMENTS, NOTIFICATION
OF ANY RELEVANT PATENT RIGHTS OF WHICH
THEY ARE AWARE AND TO PROVIDE SUPPOR TING
DOCUMENTATION.
IN ADDITION TO THEIR EVALUATION AS
Reference number
BEING ACCEPTABLE FOR INDUSTRIAL, TECHNO-
ISO/FDIS 14624-3:2023(E)
LOGICAL, COMMERCIAL AND USER PURPOSES,
DRAFT INTERNATIONAL STANDARDS MAY ON
OCCASION HAVE TO BE CONSIDERED IN THE
LIGHT OF THEIR POTENTIAL TO BECOME STAN-
DARDS TO WHICH REFERENCE MAY BE MADE IN
NATIONAL REGULATIONS. © ISO 2023

---------------------- Page: 1 ----------------------
ISO/FDIS 14624-3:2023(E)
FINAL
INTERNATIONAL ISO/FDIS
DRAFT
STANDARD 14624-3
ISO/TC 20/SC 14
Space systems — Safety and
Secretariat: ANSI
compatibility of materials —
Voting begins on:
Part 3:
Voting terminates on:
Determination of off-gassed
compounds from materials and
assembled articles
COPYRIGHT PROTECTED DOCUMENT
© ISO 2023
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
RECIPIENTS OF THIS DRAFT ARE INVITED TO
ISO copyright office
SUBMIT, WITH THEIR COMMENTS, NOTIFICATION
OF ANY RELEVANT PATENT RIGHTS OF WHICH
CP 401 • Ch. de Blandonnet 8
THEY ARE AWARE AND TO PROVIDE SUPPOR TING
CH-1214 Vernier, Geneva
DOCUMENTATION.
Phone: [phone]
IN ADDITION TO THEIR EVALUATION AS
Reference number
Email: [e-mail]
BEING ACCEPTABLE FOR INDUSTRIAL, TECHNO-
ISO/FDIS 14624-3:2023(E)
Website: www.iso.org
LOGICAL, COMMERCIAL AND USER PURPOSES,
DRAFT INTERNATIONAL STANDARDS MAY ON
Published in Switzerland
OCCASION HAVE TO BE CONSIDERED IN THE
LIGHT OF THEIR POTENTIAL TO BECOME STAN-
DARDS TO WHICH REFERENCE MAY BE MADE IN
ii
  © ISO 2023 – All rights reserved
NATIONAL REGULATIONS. © ISO 2023

---------------------- Page: 2 ----------------------
ISO/FDIS 14624-3:2023(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Principle . 3
5 Health and safety of test operators . 3
6 Test conditions .3
7 Apparatus and materials .4
8 Test samples .5
8.1 Handling/receipt . 5
8.2 Preparation .
...

2022-07-13
2023-06-26
ISO/FDIS 14624-3:20222023(E)
ISO/TC 20/SC 14
Secretariat: ANSI
Space systems — Safety and compatibility of materials — Part 3: Determination of off-
gassed productscompounds from materials and assembled articles
© ISO 2023
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no
part of this publication may be reproduced or utilized otherwise in any form or by any means,
electronic or mechanical, including photocopying, or posting on the internet or an intranet, without
prior written permission. Permission can be requested from either ISO at the address below or
ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: [phone]
Email: [e-mail]
Website: www.iso.orgSystèmes spatiaux — Sécurité et compatibilité des matériaux — Partie 3:
Détermination des produits issus du dégazage sous atmosphère des matériaux et des articles
assemblés

---------------------- Page: 1 ----------------------
ISO/FDIS 14624-3:2022(E)

Published in Switzerland
ii © ISO 2022 – All rights reserved

---------------------- Page: 2 ----------------------
ISO/FDIS 14624-3:2022(E)
Contents Page
Foreword . 4
Introduction . 5
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Principle . 4
5 Health and safety of test operators . 4
6 Test conditions . 4
7 Apparatus and materials . 4
8 Test samples . 5
8.1 Handling/receipt . 5
8.2 Preparation . 5
8.3 Cleaning . 6
8.4 Inspection . 6
9 Pretest procedure . 7
10 Test procedure . 7
11 Precision . 8
12 Test report . 8
13 Good laboratory practices (GLP) . 8
Annex A (informative) Materials and assembled articles toxic hazard index and maximum
limit mass/article example calculations . 11
Annex B (normative) Determination of off-gassed compounds from high temperature
sensitive materials and assembled articles at 40 °C . 18
Bibliography. 20

© ISO 2
...