Petroleum and natural gas industries — Corrosion-resistant alloy seamless tubular products for use as casing, tubing, coupling stock and accessory material — Technical delivery conditions

This document specifies the technical delivery conditions for corrosion-resistant alloy seamless tubular products for casing, tubing, coupling stock and accessory material (including coupling stock and accessory material from bar) for two product specification levels: — PSL-1, which is the basis of this document; — PSL-2, which provides additional requirements for a product that is intended to be both corrosion and cracking resistant for the environments and qualification method specified in Annex G and in the ISO 15156 series. At the option of the manufacturer, PSL-2 products can be provided in lieu of PSL-1. NOTE 1 The corrosion-resistant alloys included in this document are special alloys in accordance with ISO 4948-1 and ISO 4948-2. NOTE 2 For the purpose of this document, NACE MR0175 is equivalent to the ISO 15156 series. NOTE 3 Accessory products can be manufactured from coupling stock and tubular material, or from solid bar stock or from bored and heat heat-treated bar stock as covered in Annex F. This document contains no provisions relating to the connection of individual lengths of pipe. This document contains provisions relating to marking of tubing and casing after threading. This document is applicable to the following five groups of products: a) group 1, which is composed of stainless alloys with a martensitic or martensitic/ferritic structure; b) group 2, which is composed of stainless alloys with a ferritic-austenitic structure, such as duplex and super-duplex stainless alloy; c) group 3, which is composed of stainless alloys with an austenitic structure (iron base); d) group 4, which is composed of nickel-based alloys with an austenitic structure (nickel base); e) group 5, which is composed of bar only (Annex F) in age-hardened (AH) nickel-based alloys with austenitic structure. NOTE 4 Not all PSL-1 categories and grades can be made cracking resistant in accordance with the ISO 15156 series and are, therefore, not included in PSL-2.

Industries du pétrole et du gaz naturel — Produits tubulaires sans soudure en acier allié résistant à la corrosion utilisés comme tubes de cuvelage, tubes de production, tubes-ébauches pour manchons et matériau pour accessoires — Conditions techniques de livraison

General Information

Status
Published
Publication Date
18-May-2020
Current Stage
6060 - International Standard published
Start Date
04-May-2020
Due Date
12-Jun-2020
Completion Date
19-May-2020
Ref Project

Relations

Buy Standard

Standard
ISO 13680:2020 - Petroleum and natural gas industries -- Corrosion-resistant alloy seamless tubular products for use as casing, tubing, coupling stock and accessory material -- Technical delivery conditions
English language
125 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 13680
Fourth edition
2020-05
Petroleum and natural gas
industries — Corrosion-resistant
alloy seamless tubular products for
use as casing, tubing, coupling stock
and accessory material — Technical
delivery conditions
Industries du pétrole et du gaz naturel — Produits tubulaires sans
soudure en acier allié résistant à la corrosion utilisés comme tubes
de cuvelage, tubes de production, tubes-ébauches pour manchons et
matériau pour accessoires — Conditions techniques de livraison
Reference number
ISO 13680:2020(E)
©
ISO 2020

---------------------- Page: 1 ----------------------
ISO 13680:2020(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2020
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2020 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 13680:2020(E)

Contents Page
Foreword .vii
Introduction .viii
1 Scope . 1
2 Normative references . 2
3 Terms, definitions, abbreviated terms and symbols . 4
3.1 Terms and definitions . 4
3.2 Abbreviated terms . 6
3.3 Symbols . 7
4 General . 8
4.1 Dual normative references. 8
4.2 Units of measurement . . 8
5 Information supplied by the purchaser . 8
6 Manufacturing process .11
6.1 Melting practices .11
6.2 Product manufacturing process .11
6.3 Pipe end sizing .11
6.4 Straightening .11
6.5 Process requiring validation .12
6.6 Traceability .12
6.7 Manufacturing procedure qualification test .12
6.8 Process for update of alloys and/or grades .12
7 Material requirements .13
7.1 Chemical composition .13
7.2 Tensile properties .13
7.3 Hardness properties .13
7.4 Charpy V-notch test properties — General requirements .13
7.4.1 Evaluation of test results .13
7.4.2 Critical thickness.14
7.4.3 Specimen size, orientation and hierarchy .14
7.4.4 Alternative size impact test specimens .14
7.4.5 Sub-size test specimens .14
7.4.6 Test temperature .14
7.5 Charpy V-notch — Absorbed energy requirements for coupling stock and
accessory material — All grades .14
7.5.1 General.14
7.5.2 Requirements for all grades .15
7.6 Charpy V-notch — Absorbed energy requirements for pipe — All grades .15
7.7 Flattening requirements .16
7.8 Charpy V-notch test properties at low temperature for group 2 .17
7.8.1 General.17
7.8.2 Evaluation of test results .17
7.8.3 Selection of test specimens .17
7.8.4 Test temperature .17
7.8.5 Absorbed energy requirements .17
7.9 Corrosion properties .17
7.9.1 General.17
7.9.2 Pitting corrosion properties for group 2 .18
7.10 Microstructure properties .18
7.10.1 Group 1 .18
7.10.2 Group 2 .18
7.10.3 Groups 3 and 4 .18
7.11 Surface condition .18
© ISO 2020 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO 13680:2020(E)

7.12 Defects .19
7.12.1 Pipe .19
7.12.2 Coupling stock and accessory material .19
7.12.3 Process control plan.19
8 Dimensions, masses and tolerances.19
8.1 Outside diameter, wall thickness and mass.19
8.2 Length .20
8.3 Tolerances .20
8.3.1 Tolerance on outside diameter, wall thickness and mass .20
8.3.2 Inside diameter, d .20
8.3.3 Straightness .20
8.3.4 Drift requirements .20
8.4 Product ends .20
9 Inspection and testing .21
9.1 Test equipment .21
9.2 Type and frequency of tests .21
9.3 Testing of chemical composition .21
9.3.1 Chemical analysis .21
9.3.2 Test method .21
9.3.3 Chromium depletion test — Groups 2, 3 and 4 .21
9.4 Testing of mechanical characteristics .22
9.4.1 Test lot.22
9.4.2 Selection and preparation of samples and test pieces .22
9.5 Tensile test .22
9.5.1 Orientation and size of test pieces.22
9.5.2 Test method .22
9.5.3 Invalidation of test . .22
9.5.4 Retest .22
9.6 Hardness test .23
9.6.1 Test pieces .23
9.6.2 Test method .23
9.6.3 Invalidation of tests .24
9.6.4 Periodic checks of hardness-testing machines .24
9.6.5 Verification of hardness-testing machines and indenters.24
9.6.6 Retests .25
9.7 Impact or flattening test .26
9.7.1 Test pieces .26
9.7.2 Frequency of testing .26
9.7.3 Impact test method .26
9.7.4 Flattening test method . .27
9.7.5 Impact test retest .27
9.7.6 Flattening test retest.27
9.7.7 Invalidation of tests .28
9.8 Impact test at low temperature for group 2 .28
9.9 Pitting corrosion test for group 2 .28
9.10 Microstructural examination .29
9.10.1 Test pieces .29
9.10.2 Test method .29
9.10.3 Retest .30
9.11 Dimensional testing .30
9.11.1 General.30
9.11.2 Outside diameter .30
9.11.3 Wall thickness at end of products .30
9.11.4 Wall thickness of product body .30
9.12 Drift test .31
9.12.1 Non-upset and external upset pipe .31
9.12.2 Internal upset pipe .31
iv © ISO 2020 – All rights reserved

---------------------- Page: 4 ----------------------
ISO 13680:2020(E)

9.12.3 Drift mandrel coating . .31
9.13 Length .31
9.14 Straightness .31
9.15 Mass determination .31
9.16 Visual inspection .31
9.16.1 General.31
9.16.2 Pipe body, coupling stock and accessory material .32
9.16.3 Pipe ends.32
9.16.4 Disposition .32
9.17 Non-destructive examination .32
9.17.1 General.32
9.17.2 NDE personnel .33
9.17.3 Products .33
9.17.4 Pup joints . .33
9.17.5 Untested ends .33
9.17.6 Upset ends .33
9.17.7 Reference standards .34
9.17.8 NDE system capability records .34
9.17.9 All product group 1 .35
9.17.10 Full-body NDE of product — Groups 2, 3 and 4 .35
9.17.11 Pipe, coupling stock and accessory material requiring further evaluation .35
9.17.12 Evaluation of indications (prove-up) .35
9.17.13 Disposition of pipe containing defects .36
9.17.14 Disposition of coupling stock and accessory material containing defects .37
9.18 Positive material identification .37
10 Surface treatment .38
10.1 Group 1 .38
10.2 Groups 2, 3 and 4 .38
11 Marking .39
11.1 General .39
11.2 Colour-code identification .39
11.3 Marking content and sequence .39
11.4 Marking informative for couplings, pup joints and accessories after threading .40
12 Surface protection — Group 1 .40
13 Documents .41
13.1 Electronic media .41
13.2 Retention of records .41
13.3 Test certificates .41
14 Handling, packaging and storage .42
14.1 General .42
14.2 Handling.42
14.3 Packaging .42
14.3.1 General.42
14.3.2 Identification .42
14.4 Storage .43
Annex A (normative) Tables in SI units .
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.