Cutting tool data representation and exchange — Part 308: Creation and exchange of 3D models — Milling cutters with arbor hole for indexable inserts

ISO/TS 13399-308:2016 specifies a concept for the design of tool items, limited to any kind of milling cutters with arbor hole for indexable inserts, together with the usage of the related properties and domains of values. ISO/TS 13399-308:2016 specifies a common way of design simplified models that contain the following: - definitions and identifications of the design features of milling cutters with arbor hole for indexable inserts, with an association to the used properties; - definitions and identifications of the internal structure of the 3D model that represents the features and the properties of milling cutters with arbor hole for indexable inserts. The following are outside the scope of this part of ISO/TS 13399: - applications where these standard data may be stored or referenced; - concept of 3D models for cutting tools; - concept of 3D models for cutting items; - concept of 3D models for other tool items not being described in the scope of this part of ISO/TS 13399; - concept of 3D models for adaptive items; - concept of 3D models for assembly items and auxiliary items.

Représentation et échange des données relatives aux outils coupants — Partie 308: Création et échange des modèles 3D — Fraises à trou central pour plaquettes amovibles

La présente partie de l'ISO/TS 13399 spécifie un concept pour la conception des éléments relatifs aux outils, limité à tous les types de fraises à trou central pour plaquettes amovibles, utilisant les propriétés et domaines de valeurs associés. La présente partie de l'ISO/TS 13399 spécifie une façon commune de concevoir des modèles simplifiés contenant les éléments suivants: — des définitions et identifications des caractéristiques de conception des fraises à trou central pour plaquettes amovibles, avec un lien vers les propriétés utilisées; — des définitions et identifications de la structure interne du modèle 3D qui représente les caractéristiques et les propriétés des fraises à trou central pour plaquettes amovibles; Les éléments suivants n'entrent pas dans le domaine d'application de la présente partie de l'ISO/TS 13399: — les applications où les données standards peuvent être stockées ou référencées; — le concept de modèles 3D pour les outils coupants; — le concept de modèles 3D pour les éléments coupants; — le concept de modèles 3D pour d'autres éléments de l'outil non décrits dans le domaine d'application de la présente partie de l'ISO/TS 13399; — le concept de modèles 3D pour les éléments relatifs aux attachements; — le concept de modèles 3D pour les éléments relatifs aux assemblages et éléments auxiliaires.

General Information

Status
Published
Publication Date
01-Feb-2016
Current Stage
9020 - International Standard under periodical review
Start Date
15-Jul-2025
Completion Date
15-Jul-2025
Ref Project

Buy Standard

Technical specification
ISO/TS 13399-308:2016 - Cutting tool data representation and exchange
English language
46 pages
sale 15% off
Preview
sale 15% off
Preview
Technical specification
ISO/TS 13399-308:2016 - Cutting tool data representation and exchange
English language
46 pages
sale 15% off
Preview
sale 15% off
Preview
Technical specification
ISO/TS 13399-308:2016 - Représentation et échange des données relatives aux outils coupants
French language
47 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)


TECHNICAL ISO/TS
SPECIFICATION 13399-308
First edition
Cutting tool data representation and
exchange —
Part 308:
Creation and exchange of 3D models
— Milling cutters with arbor hole for
indexable inserts
Représentation et échange des données relatives aux outils coupants —
Partie 308: Création et échange des modèles 3D — Fraises à métaux à
trou de fixation et à plaquettes amovibles
PROOF/ÉPREUVE
Reference number
ISO/TS 13399-308:2015(E)
©
ISO 2015
ISO/TS 13399-308:2015(E)
© ISO 2015, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2015 – All rights reserved

ISO/TS 13399-308:2015(E)
Contents Page
Foreword .v
Introduction .vii
1 Scope . 1
2 Normative references . 1
3 Starting elements, coordinate systems, planes . 2
3.1 General . 2
3.2 Reference system . 2
3.3 Coordinate system at the cutting part . 3
3.4 Planes . 3
3.5 Design of the pocket seat and cutting reference point (CRP) of the insert . 4
3.6 Adjustment coordinate system on workpiece side . 7
3.6.1 General. 7
3.6.2 Designation of the coordinate system workpiece side . 8
4 Design of the model . 9
4.1 General . 9
4.2 Necessary parameters for the connection interface feature .10
4.3 Necessary properties for inserts .10
4.3.1 General.10
4.3.2 Properties for equilateral, equiangular and equilateral, nonequiangular inserts 10
4.3.3 Properties for nonequilateral, equiangular and nonequilateral,
nonequiangular inserts .11
4.3.4 Design of the pocket seat feature.12
5 Face milling cutter .12
5.1 General .12
5.2 Necessary properties .13
5.3 Basic geometry .13
5.4 Determination of the position of the mounting coordinate system of insert .14
5.5 Chip flute and pocket seat .15
5.6 Face milling cutter, assembly .16
6 Shoulder milling cutter .17
6.1 General .17
6.2 Necessary properties .17
6.3 Basic geometry .17
6.4 Determination of the position of the mounting coordinate system of insert .17
6.5 Chip flute and pocket seat .18
6.6 Shoulder milling cutter, assembly .18
7 Plain milling cutter .19
7.1 General .19
7.2 Necessary properties .19
7.3 Basic geometry .20
7.4 Determination of the position of the mounting coordinate system of insert .20
7.5 Chip flute and pocket seat .21
7.6 Plain milling cutter, assembly.23
8 Shell milling cutter .23
8.1 General .23
8.2 Necessary properties .24
8.3 Basic geometry .24
8.4 Determination of the position of the mounting coordinate system of insert .25
8.5 Chip flute and pocket seat .25
8.6 Shell milling cutter, assembly .25
9 Full-side-slot milling cutter .25
ISO/TS 13399-308:2015(E)
9.1 General .25
9.2 Necessary properties .26
9.3 Basic geometry .26
9.4 Determination of the position of the mounting coordinate system of insert .27
9.5 Chip flute and pocket seat .28
9.6 Assembly of a full-side slot milling cutter .30
10 Half-side slot milling cutter .31
10.1 General .31
10.2 Necessary properties .31
10.3 Basic geometry .31
10.4 Determination of the position of the mounting coordinate system of insert .31
10.5 Chip flute and pocket seat .32
10.6 Half-side slot milling cutter, assembly .32
11 Full-side profile slot milling cutter .33
11.1 General .33
11.2 Necessary properties .33
11.3 Basic geometry .34
11.4 Determination of the position of the mounting coordinate system of insert .34
11.5 Chip flute and pocket seat .34
11.6 Full-side profile slot milling cutter, assembly.34
12 Full-side angular slot milling cutter .35
12.1 General .35
12.2 Necessary properties .
...


TECHNICAL ISO/TS
SPECIFICATION 13399-308
First edition
2016-02-01
Cutting tool data representation and
exchange —
Part 308:
Creation and exchange of 3D models
— Milling cutters with arbor hole for
indexable inserts
Représentation et échange des données relatives aux outils coupants —
Partie 308: Création et échange des modèles 3D — Fraises à métaux à
trou de fixation et à plaquettes amovibles
Reference number
©
ISO 2016
© ISO 2016, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2016 – All rights reserved

Contents Page
Foreword .v
Introduction .vii
1 Scope . 1
2 Normative references . 1
3 Starting elements, coordinate systems, planes . 2
3.1 General . 2
3.2 Reference system . 2
3.3 Coordinate system at the cutting part . 3
3.4 Planes . 3
3.5 Design of the pocket seat and cutting reference point (CRP) of the insert . 4
3.6 Adjustment coordinate system on workpiece side . 7
3.6.1 General. 7
3.6.2 Designation of the coordinate system workpiece side . 8
4 Design of the model . 9
4.1 General . 9
4.2 Necessary parameters for the connection interface feature .10
4.3 Necessary properties for inserts .10
4.3.1 General.10
4.3.2 Properties for equilateral, equiangular and equilateral, nonequiangular inserts 10
4.3.3 Properties for nonequilateral, equiangular and nonequilateral,
nonequiangular inserts .11
4.3.4 Design of the pocket seat feature.12
5 Face milling cutter .12
5.1 General .12
5.2 Necessary properties .13
5.3 Basic geometry .13
5.4 Determination of the position of the mounting coordinate system of insert .14
5.5 Chip flute and pocket seat .15
5.6 Face milling cutter, assembly .16
6 Shoulder milling cutter .17
6.1 General .17
6.2 Necessary properties .17
6.3 Basic geometry .17
6.4 Determination of the position of the mounting coordinate system of insert .17
6.5 Chip flute and pocket seat .18
6.6 Shoulder milling cutter, assembly .18
7 Plain milling cutter .19
7.1 General .19
7.2 Necessary properties .19
7.3 Basic geometry .20
7.4 Determination of the position of the mounting coordinate system of insert .20
7.5 Chip flute and pocket seat .21
7.6 Plain milling cutter, assembly.23
8 Shell milling cutter .23
8.1 General .23
8.2 Necessary properties .24
8.3 Basic geometry .24
8.4 Determination of the position of the mounting coordinate system of insert .25
8.5 Chip flute and pocket seat .25
8.6 Shell milling cutter, assembly .25
9 Full-side-slot milling cutter .25
9.1 General .25
9.2 Necessary properties .26
9.3 Basic geometry .26
9.4 Determination of the position of the mounting coordinate system of insert .27
9.5 Chip flute and pocket seat .28
9.6 Assembly of a full-side slot milling cutter .30
10 Half-side slot milling cutter .31
10.1 General .31
10.2 Necessary properties .31
10.3 Basic geometry .31
10.4 Determination of the position of the mounting coordinate system of insert .31
10.5 Chip flute and pocket seat .32
10.6 Half-side slot milling cutter, assembly .32
11 Full-side profile slot milling cutter .33
11.1 General .33
11.2 Necessary properties .33
11.3 Basic geometry .34
11.4 Determination of the position of the mounting coordinate system of insert .34
11.5 Chip flute and pocket seat .34
11.6 Full-side profile slot milling cutter, assembly.34
12 Full-side angular slot milling cutter .35
12.1 General .35
12.2 Necessary properties .
...


SPÉCIFICATION ISO/TS
TECHNIQUE 13399-308
Première édition
2016-02-01
Représentation et échange des
données relatives aux outils
coupants —
Partie 308:
Création et échange des modèles 3D —
Fraises à trou central pour plaquettes
amovibles
Cutting tool data representation and exchange —
Part 308: Creation and exchange of 3D models — Milling cutters with
arbor hole for indexable inserts
Numéro de référence
©
ISO 2016
DOCUMENT PROTÉGÉ PAR COPYRIGHT
© ISO 2016
Tous droits réservés. Sauf prescription différente ou nécessité dans le contexte de sa mise en œuvre, aucune partie de cette
publication ne peut être reproduite ni utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique,
y compris la photocopie, ou la diffusion sur l’internet ou sur un intranet, sans autorisation écrite préalable. Une autorisation peut
être demandée à l’ISO à l’adresse ci-après ou au comité membre de l’ISO dans le pays du demandeur.
ISO copyright office
Case postale 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Genève
Tél.: +41 22 749 01 11
Fax: +41 22 749 09 47
E-mail: copyright@iso.org
Web: www.iso.org
Publié en Suisse
ii © ISO 2016 – Tous droits réservés

Sommaire Page
Avant-propos .v
Introduction .vii
1 Domaine d'application . 1
2 Références normatives . 1
3 Éléments de départ, systèmes de coordonnées, plans . 2
3.1 Généralités . 2
3.2 Système de référence . 2
3.3 Système de coordonnées sur la partie coupante . 3
3.4 Plans . 3
3.5 Conception du logement et point de coupe de référence (CRP) de la plaquette. 4
3.6 Système de coordonnées de réglage côté pièce . 7
3.6.1 Généralités . 7
3.6.2 Désignation des systèmes de coordonnées côté pièce . 8
4 Conception du modèle . 9
4.1 Généralités . 9
4.2 Paramètres nécessaires pour la caractéristique d’interface de connexion.10
4.3 Propriétés nécessaires pour les plaquettes .10
4.3.1 Généralités .10
4.3.2 Propriétés pour les plaquettes équilatérales et équiangles et les
plaquettes équilatérales et non-équiangles .10
4.3.3 Propriétés pour les plaquettes non-équilatérales et équiangles, et non-
équilatérales et non-équiangles .11
4.3.4 Conception des caractéristiques du logement .12
5 Fraise à surfacer .12
5.1 Généralités .12
5.2 Propriétés nécessaires .13
5.3 Géométrie de base .13
5.4 Détermination de la position du système de coordonnées de montage de la plaquette .14
5.5 Goujure et logement .15
5.6 Assemblage de la fraise à surfacer .16
6 Fraise à surfacer et dresser .17
6.1 Généralités .17
6.2 Propriétés nécessaires .17
6.3 Géométrie de base .17
6.4 Détermination de la position du système de coordonnées de montage de la plaquette .18
6.5 Goujure et logement .18
6.6 Assemblage de la fraise à surfacer et dresser .18
7 Fraise une taille à surfacer .19
7.1 Généralités .19
7.2 Propriétés nécessaires .19
7.3 Géométrie de base .20
7.4 Détermination de la position du système de coordonnées de montage de la plaquette .20
7.5 Goujure et logement .21
7.6 Assemblage de la fraise une taille à surfacer .23
8 Fraise creuse .23
8.1 Généralités .23
8.2 Propriétés nécessaires .24
8.3 Géométrie de base .24
8.4 Détermination de la position du système de coordonnées de montage de la plaquette .24
8.5 Goujure et logement .25
8.6 Assemblage de la fraise creuse .25
9 Fraise trois tailles à rainurer .25
9.1 Généralités .25
9.2 Propriétés nécessaires .25
9.3 Géométrie de base .26
9.4 Détermination de la position du système de coordonnées de montage de la plaquette .27
9.5 Goujure et logement .28
9.6 Assemblage des fraises trois tailles à rainurer .30
10 Fraise deux tailles à rainurer .31
10.1 Généralités .31
10.2 Propriétés nécessaires .31
10.3 Géométrie de base .31
10.4 Détermination de la position du système de coordonnées de montage de la plaquette .31
10.5 Goujure et logement .32
10.6 Assemblage des fraises deux tailles à rainurer .32
11 Fraise profilée trois tailles à rainurer .33
11.1 Généralités .33
11.2 Propriétés nécessaires .33
11.3 Géométrie de base .34
11.4 Détermination de la position du système de coordonnées de montage de la plaquette .34
11.5 Goujure et logement .34
11.6 Assemblage des fraises deux tailles à rainurer .34
12 Fraise angulaire trois tailles à rainurer .35
12.1 Généralités .35
12.2 Propriétés nécessaires .35
12.3 Géométrie de base .36
12.4 Déterm
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.