ISO 6442:2005

Door leaves — General and local flatness — Measurement method

ISO 6442:2005 can be applied to all rectangular door leaves. ISO 6442:2005 specifies the method to be used to measure the deviations in general and local flatness of door leaves. In ISO 6442:2005, the concept of local flatness deviation is limited to defects considered to be prejudicial to the appearance of the door leaf.

Vantaux de portes — Planéités générale et locale — Méthode de mesure

L'ISO 6442:2005 peut s'appliquer à tous les vantaux de portes rectangulaires. L'ISO 6442:2005 définit la méthode à utiliser pour mesurer les écarts de planéité générale et locale des vantaux. Dans l'ISO 6442:2005 le concept d'écart de planéité locale est limité aux défauts considérés comme préjudiciables à l'aspect du vantail.

General Information

• Status: Published
• Publication Date: 19-Oct-2005
• ICS: 91.060.50 - Doors and windows
• Technical Committee: ISO/TC 162 - Doors, windows and curtain walling
• Drafting Committee: ISO/TC 162 - Doors, windows and curtain walling
• Current Stage: 9093 - International Standard confirmed
• Completion Date: 05-Oct-2020

Relations

• Revises: ISO 6442:1981 - Door leaves — Measurement of defects of general flatness
• Effective Date: 15-Apr-2008

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 6442
Second edition
2005-10-15

Door leaves — General and local
flatness — Measurement method
Vantaux de portes — Planéités générale et locale — Méthode de
mesure




Reference number
ISO 6442:2005(E)
©
ISO 2005

---------------------- Page: 1 ----------------------
ISO 6442:2005(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.


©  ISO 2005
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail [e-mail]
Web www.iso.org
Published in Switzerland

ii © ISO 2005 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 6442:2005(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 6442 was prepared by Technical Committee CEN/TC 33, Doors, windows, shutters, building hardware
and curtain walling (as EN 952:1999) and was adopted, under a special “fast-track procedure”, by Technical
Committee ISO/TC 162, Doors and windows in parallel with its approval by the ISO member bodies.
This second edition cancels and replaces the first edition (ISO 6442:1981) which has been technically revised.
Throughout the text of this document, read “. this European Standard .” to mean “. this International
Standard .”.

© ISO 2005 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO 6442:2005(E)
Page 2

EN 952:1999
Foreword
This European Standard has been prepared by Technical Committee CEN/TC 33 “Doors,
windows, shutters and building hardware”, the secretariat of which is held by AFNOR.
This European Standard supersedes EN 24:1974.
This European Standard shall be given the status of a national standard, either by publication of
an identical text or by endorsement, at the latest by Februa
...