ISO 17069:2014
(Main)Accessible design — Consideration and assistive products for accessible meeting
Accessible design — Consideration and assistive products for accessible meeting
ISO 17069:2014 specifies considerations to be taken, as well as support and assistive products that can be used when organizing a physical meeting in which older persons and persons with disabilities can actively participate. Teleconferences and web conferences are important methods that can be used to include older persons and persons with disabilities in meetings.
Conception accessible — Considérations et produits d'assistance pour réunion accessible
General Information
Relations
Buy Standard
Standards Content (Sample)
INTERNATIONAL ISO
STANDARD 17069
First edition
2014-10-15
Accessible design — Consideration
and assistive products for accessible
meeting
Conception accessible — Considérations et produits d’assistance pour
réunion accessible
Reference number
ISO 17069:2014(E)
©
ISO 2014
---------------------- Page: 1 ----------------------
ISO 17069:2014(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2014
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2014 – All rights reserved
---------------------- Page: 2 ----------------------
ISO 17069:2014(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Terms and definitions . 1
3 Planning and management for full participation . 2
3.1 Principle . 2
3.2 Specific considerations and supports . 3
Annex A (informative) Guidelines in relation to the process of organizing an accessible meeting .8
Annex B (informative) Prior registration form for an accessible meeting .15
Bibliography .17
© ISO 2014 – All rights reserved iii
---------------------- Page: 3 ----------------------
ISO 17069:2014(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any
patent rights identified during the development of the document will be in the Introduction and/or on
the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity
assessment, as well as information about ISO’s adherence to the WTO principles in the Technical Barriers
to Trade (TBT) see the following URL: Foreword - Supplementary information.
The committee responsible for this document is ISO/TC 173, Assistive products for persons with disability,
Subcommittee SC 7, Accessible design.
iv © ISO 2014 – All rights reserved
---------------------- Page: 4 ----------------------
ISO 17069:2014(E)
Introduction
There are various types of meetings, ranging from small gatherings in families, schools, workplaces, and
towns, to bigger ones such as academic meetings, sessions in congresses, and international conferences.
Participation in meetings is indispensable for full participation and inclusion in society as envisioned in
the United Nations Convention on the Rights of Persons with Disabilities.
As social participation of older persons and persons with disabilities is promoted, more older persons
and persons with disabilities are taking the opportunity to attend meetings. To ensure that all persons
can participate in a meeting in a meaningful way, considerations are required to be taken to overcome
any obstacle that can be a hindrance. Printed meeting notices and documents might not be appropriate
for a participant who has a seeing impairment or who is blind. Complicated texts might be a hindrance
for a person who has a cognitive impairment. Discussions might be difficult to follow for a participant
who has hearing impairment or who is deaf. Narrow passages, gaps, and stairs might be barriers for a
person who uses a wheelchair or assistive products for walking. Persons with speech disability might
have difficulties expressing themselves in a meeting without any support.
Meeting organizers have to understand and address hindrances so that all participants can fully take
part in the meeting. Careful planning, support staff, and use of appropriate assistive products can
overcome hindrances. Preparation of meeting materials in alternative formats such as large print, braille,
or digital formats can facilitate understanding for a person who has seeing impairment or who is blind.
Texts that are clear and concise can facilitate understanding for a person with cognitive impairment.
Amplification of speech by using microphones can be appropriate support for a person with hearing
impairment. Sign language interpreters can assist a person who is deaf to follow and participate in a
discussion. A built environment with elevators and ramps can make an area accessible for a person with
mobility limitation.
This International Standard identifies areas to consider, as well as support and assistive products that
can facilitate the full participation of older persons and persons with disabilities in meetings.
In this International Standard, considerations and assistive products that can contribute to making a
meeting accessible are presented in relation to human abilities. To facilitate for meeting organizers,
Annex A presents detailed guidelines and a checklist in relation to the process of organizing an accessible
meeting.
© ISO 2014 – All rights reserved v
---------------------- Page: 5 ----------------------
INTERNATIONAL STANDARD ISO 17069:2014(E)
Accessible design — Consideration and assistive products
for accessible meeting
1 Scope
This International Standard specifies considerations to be taken, as well as support and assistive
products that can be used when organizing a physical meeting in which older persons and persons with
disabilities can actively participate.
Teleconferences and web conferences are important methods that can be used to include older persons
and persons with disabilities in meetings.
2 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
2.1
accessible meeting
meeting which is organized so that older persons and persons with disabilities can participate actively
and where required, assistive products and support staff are used to facilitate participation
2.2
assitive product
any product (including devices, equipment, instruments, and software), especially produced or generally
available, used by or for persons with disability for the following functions:
— for participation;
— to protect, support, train, measure or substitute for body functions/structures and activities;
— to prevent impairments, activity limitations, or participation restrictions
[SOURCE: ISO 9999:2011, 2.3]
2.3
support staff
person who performs tasks to facilitate the execution of an accessible meeting which can include, but
are not limited to, interpreting, note taking, guiding, and assisting participation of older persons and
persons with disabilities
Note 1 to entry: Support staff includes guide assistant (2.4) and communication assistant (2.5).
2.4
guide assistant
person who leads and assists a person in a location in an appropriate manner for that person’s impairment
2.5
communication assistant
person who assists with communication
EXAMPLE 1 A person who conveys proceedings of meetings and discussions using sign languages, live
captioning, by paraphrasing or by Assistive Augmented Communication (AAC).
EXAMPLE 2 A person who expresses opinions on behalf of a participant.
EXAMPLE 3 A person who assists participant to follow documentation, e.g. turns pages of documents, points
out information in documents.
© ISO 2014 – All rights reserved 1
---------------------- Page: 6 ----------------------
ISO 17069:2014(E)
2.6
attendant
person who accompanies an older person or a person with disability and enables them to participate in
the meeting
2.7
information services
interactive communication support using support staff and assistive products so that older persons and
persons with disabilities can actively participate
3 Planning and management for full participation
3.1 Principle
3.1.1 Basic principle
Meeting organizers should be aware of factors that can hinder the participation of older persons and
persons with disabilities in meetings.
When planning a meeting, the organizer should identify and consider measures they should take to
facilitate full participation of the persons who intend to participate in the meeting. When appropriate,
arrangements should be made for web conferencing such as captioning services, and auditory or textual
expression for non-textual presentations. For public or open meetings where prior registration is not
feasible, the organizer should carry out measures to ensure reasonable accommodation.
3.1.2 Before the meeting
All participants should receive necessary information (e.g. notice, invitation, agenda, meeting documents)
in an appropriate format and be requested to express any requirements they might have in relation to
active participation. For this purpose, prior registration can be helpful. (See Annex B).
NOTE Information on formatting is available in W3C/WAI document at http://www.w3.org/WAI/
training/accessible.php
The meeting venue and program should be checked to ensure that they accommodate the requirements
of the participants.
The meeting organizers should inform staff concerning requirements of participants.
The meeting organizers and support staff should plan how they will provide the support required
and emergency procedures in relation to participants’ requirements. Communication methods for
emergency situations and evacuation procedures should be established and clarified.
The meeting organizers should brief speakers, workshop leaders, moderators, etc. concerning
considerations to be taken when presenting and leading the meeting in relation to the participants’
requirements.
The meeting organizers should inform all meeting participants of any allergens or sensitizing substances
that they should not wear, use, or bring to the meeting in relation to the participants’ requirements.
The meeting organizers should provide information concerning accessibility of the web conferencing
software adopted.
3.1.3 At the meeting
Information presented at the meeting should accommodate the requirements of the participants.
Information on meeting schedule (e.g. time for pauses, lunch breaks, end of meeting) and venue
(e.g. location of restrooms) should be given when opening the meeting.
2 © ISO 2014 – All rights reserved
---------------------- Page: 7 ----------------------
ISO 17069:2014(E)
All participants should be informed of considerations they should take to ensure that all present can
participate actively. Such considerations include, but are not limited to, information on special seating
arrangements, use of microphone, speaking slowly to allow for interpretation, introducing themselves
before speaking, and any allergy, intolerance, or hypersensitivity considerations.
When appropriate, a procedure/system should be established for participants to signal (e.g. with cards)
need of a short pause in discussions when more time is needed before discussions are continued (e.g. to
consult with interpreter, assistant, or attendant).
Organizers should ensure that all participants can take part in discussions during breaks, lunch, and
breakout meetings.
3.1.4 After the meeting
Meeting materials and minutes (including any handouts and presentations) should be produced and
sent to participants in appropriate formats.
Participants should be given the opportunity to give feedback concerning accessibility of the meeting.
Meeting organizers should review feedback and make adjustments in planning procedures or checklists
for subsequent meetings.
3.2 Specific considerations and supports
3.2.1 General
This Clause includes considerations and supports in relation to specific human functions. Further
information on accessibility, design considerations, and human functions, abilities, or disabilities can be
found in ISO/IEC Guide 71.
Examples of related support include assistive products and personnel that are provided by the meeting
organizer and those brought to the meeting by a person with disability. For those that are brought to the
meeting by the participant, the organizer should ensure that the assistive product or personnel can be
accommodated at the meeting.
3.2.2 Seeing
3.2.2.1 Considerations
Considerations should be taken regarding written information, mobility, and orientation in relation to
blindness and seeing impairment as well as appropriate colour scheme in relation to colour identification
disability.
If appropriate, information on the meeting venue should be made available prior to the meeting or
explained orally on site.
3.2.2.2 Examples of related support
The following are examples of related support for blindness and seeing impairments:
— appropriate colour scheme in documents and signage (colour identification disability);
— audio or enlarged letters version of documents (seeing impairment);
— braille, audio, or digital version of documents (blind);
— devices such as braille displays, braille typewriters, slates, computers with reading application
(blind);
— devices such as image-enlarging video systems, large screen monitors (seeing impairment);
© ISO 2014 – All rights reserved 3
---------------------- Page: 8 ----------------------
ISO 17069:2014(E)
— tactile walking surface indicator, tactile guide maps, etc. (seeing impairment, blind);
— support staff such as guide assistants;
— work space to accommodate attendants;
— relevant information (e. g. introduction of participants in relation to where they are seated at start
of meeting, if appropriate);
— list of keyboard shortcuts for the web conferencing software.
3.2.3 Hearing
3.2.3.1 Considerations
Considerations such as good sound environment throughout the premises and good lighting to facilitate
lip reading should be taken into consideration in relation to spoken communication, presentations,
discussions, and audio alarm notifications.
3.2.3.2 Examples of related support
The following are examples of related support for hearing impairments:
— projectors, white boards;
— amplifiers, loudspeakers (hearing impairment);
— good lighting, especially on the person speaking to facilitate lip reading (hearing impairment, deaf);
— microphones (hearing impairment);
— assistive systems for hearing (hearing impairment, deaf, deafblind), e.g. induction loop system,
infrared systems for audio information, and radio frequency transmission system;
— sign language interpretation (deaf, hearing impairment);
— speech to text/CART (deaf, hearing impairment). CART (Communication Access Realtime
Translation) is realtime display of verbatim report on a computer or large screen, using a special
keyboard/stenotype via special software;
— captioning/subtitling (deaf, hearing impairment): captioning is to provide a piece of text appearing
on screen as part of a film or broadcast; while subtitling is to provide captions displayed at the
bottom of a cinema or television screen that translate or transcribe the dialogue or narrative;
— live captioning provided by the web conferencing software;
— note-taking (deaf, hearing impairment): note-taking is to produce a summary report by hand-
written paper (manual note-taking) or on screen of laptop computer (computerized note-taking);
— interpreting system as per preference or requirement of participant (deafblind);
— information services and communication assistants;
— work space to accommodate attendants;
— relevant information.
4 © ISO 2014 – All rights reserved
---------------------- Page: 9 ----------------------
ISO 17069:2014(E)
3.2.4 Touch
3.2.4.1 Considerations
Meeting venues should be inspected in relation to anything that might require intact sensory ability such
as sharp edges and hot or cold surfaces. If there are any questions concerning safety, the participants
with sensory impairment should be contacted prior to meeting.
3.2.5 Taste and/or smell
3.2.5.1 Considerations
Consideration should be taken in relation to anything that requires intact taste and/or smell abilities. If
there are any questions concerning safety, participants with taste and/or smell impairment should be
contacted prior to meeting.
3.2.6 Hand and arm use
3.2.6.1 Considerations
Meeting venues and routes to local parking and transportation facilities should be inspected in relation
to anything that can hinder hand and arm use, such as doors that are manually opened, placement of
objects and materials that are to be handled, etc.
3.2.6.2 Examples of related support
The following are examples of related support for hand and arm use impairments:
— alternate routes with appropriate signage;
— arrangement of meeting room and placement of documents, materials, refreshments, etc.;
— support staff, guide assistant;
— work space to accommodate attendants;
— relevant information.
NOTE Hand and arm use corresponds to upper body structure functions and fine hand use abilities in
ISO/IEC Guide 71.
3.2.7 Mobility
3.2.7.1 Considerations
Meeting venues and routes to local parking and transportation facilities should be inspected in relation
to anything that can hinder mobility, such as uneven pavement, steps, lack of adequate space for those
who have mobility impairment, or who use walking aids and wheelchairs.
3.2.7.2 Examples of related support
The following are examples of related support for mobility impairments:
— elimination or avoidance of hindrances or hazards that can cause tripping and/or falls;
— alternate routes with appropriate signage;
— arrangement of meeting room and placement of documents, materials, refreshments, etc.;
© ISO 2014 – All rights reserved 5
---------------------- Page: 10 ----------------------
ISO 17069:2014(E)
— support staff, guide assistant;
— work space to accommodate attendants;
— relevant information.
NOTE Mobility corresponds to lower body structure functions in ISO/IEC Guide 71.
3.2.8 Voice and speech
3.2.8.1 Considerations
Considerations should be taken in relation to the number of participants, acoustics, and size of room.
Meeting organizers should check with participants with voice and speech impairment prior to meeting
concerning appropriate support and alternative forms of communication, such as “sign language” or
“augumentative and alternative communication technology”. Other means of communication support
can be appropriate depending on individual needs and situations.
3.2.8.2 Examples of related support
The following are examples of related support for voice and speech impairment:
— microphones;
— voice amplifiers;
— support staff, communication assistant;
— work space to accommodate attendants;
— relevant information.
3.
...
DRAFT INTERNATIONAL STANDARD ISO/DIS 17069
ISO/TC 173/SC 7 Secretariat: JISC
Voting begins on Voting terminates on
2013-08-05 2013-11-05
INTERNATIONAL ORGANIZATION FOR STANDARDIZATION МЕЖДУНАРОДНАЯ ОРГАНИЗАЦИЯ ПО СТАНДАРТИЗАЦИИ ORGANISATION INTERNATIONALE DE NORMALISATION
Accessible design — Consideration and assistive products for
accessible meeting
Conception accessible — Considérations et produits d'assistance pour réunion accessible
ICS 11.180.01; 13.180
To expedite distribution, this document is circulated as received from the committee
secretariat. ISO Central Secretariat work of editing and text composition will be undertaken at
publication stage.
Pour accélérer la distribution, le présent document est distribué tel qu'il est parvenu du
secrétariat du comité. Le travail de rédaction et de composition de texte sera effectué au
Secrétariat central de l'ISO au stade de publication.
THIS DOCUMENT IS A DRAFT CIRCULATED FOR COMMENT AND APPROVAL. IT IS THEREFORE SUBJECT TO CHANGE AND MAY NOT BE
REFERRED TO AS AN INTERNATIONAL STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS BEING ACCEPTABLE FOR INDUSTRIAL, TECHNOLOGICAL, COMMERCIAL AND USER PURPOSES,
DRAFT INTERNATIONAL STANDARDS MAY ON OCCASION HAVE TO BE CONSIDERED IN THE LIGHT OF THEIR POTENTIAL TO BECOME
STANDARDS TO WHICH REFERENCE MAY BE MADE IN NATIONAL REGULATIONS.
RECIPIENTS OF THIS DRAFT ARE INVITED TO SUBMIT, WITH THEIR COMMENTS, NOTIFICATION OF ANY RELEVANT PATENT RIGHTS OF WHICH
THEY ARE AWARE AND TO PROVIDE SUPPORTING DOCUMENTATION.
© International Organization for Standardization, 2013
---------------------- Page: 1 ----------------------
ISO/DIS 17069
COPYRIGHT PROTECTED DOCUMENT
© ISO 2013
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any
means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission.
Permission can be requested from either ISO at the address below or ISO’s member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2013 – All rights reserved
---------------------- Page: 2 ----------------------
ISO/DIS 17069
Contents Page
Foreword . iv
Introduction . v
1 Scope . 1
2 Normative reference . 1
3 Terms and definitions . 1
4. Planning and management for full participation . 2
4.1 Principle . 2
Annex A (Informative) . 7
Annex B Prior registration form for accessible meeting . 12
Bibliography . 14
© ISO 2002 – All rights reserved iii
---------------------- Page: 3 ----------------------
ISO/DIS 17069
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
ISO XXXxx was prepared by Technical Committee ISO/TC 173, TC Assitive Products, Subcommittee SC 7,
Accessible Design.
iv © ISO 2002 – All rights reserved
---------------------- Page: 4 ----------------------
ISO/DIS 17069
Introduction
There are various types of meetings, ranging from small gatherings in families, schools, workplaces and towns,
to bigger ones such as academic meetings, sessions in congresses and international conferences.
Participation in meetings and conferences is indispensable for full and effective participation, and inclusion in
society as envisioned in the United Nations Convention on the Rights of Persons with Disabilities.
As social participation of older persons and persons with disabilities is promoted, their opportunities to attend
meetings increase. To ensure that all persons can participate in a meeting in a meaningful way considerations
are required to be taken to overcome any obstacle that can hinder an older person or a person with a
disability. Printed meeting notices and documents may not be appropriate for a participant who has a seeing
impairment or who is blind. Complicated texts may be a hinder for a person who has a cognitive impairment.
Discussions may be difficult to follow for a participant who has hearing impairment or who is deaf. Narrow
passages, gaps and stairs may be barriers for a person who uses a wheelchair or assistive products for
walking.
Meeting organizers should understand and address obstacles that can hinder active and meaningful
participation so that all participants can fully take part in the meeting. Careful planning, support staff and use
of appropriate assistive products can overcome the obstacles. Preparation of meeting materials in alternative
formats such as large print, braille or digital formats can facilitate for a person who has seeing impairment or
who is blind. Amplification of speech by using microphones can be appropriate support for a person with
hearing impairment. Sign language interpreters can assist a person who is deaf to follow and participate in a
discussion. Texts that are clear and concise can facilitate understanding for a person with cognitive
impairment. A built environment with elevators and ramps can make the area accessible for a person with
mobility limitation. This International Standard identifies areas to consider, support and assistive products that
can facilitate the participation of older persons and persons with disabilities in meetings.
© ISO 2002 – All rights reserved v
---------------------- Page: 5 ----------------------
WORKING DRAFT
ISO/DIS 17069
Accessible Design — Considerations and assistive products for
accessible meeting
1 Scope
This International Standard specifies considerations to be taken, support and assistive products that can be
used when organizing a physical meeting in which older persons and persons with disabilities can actively
participate. Teleconferences and web conferences are important methods that can be used to include older
persons and persons with disabilities in meetings but are not within the scope of this International Standard.
2 Normative reference
The following document applies to this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including supplements) applies.
ISO/IEC Guide 71
ISO 9999 Assistive Products for Persons with Disability - Classification and terminology
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
3.1
accessible meeting
meeting which is organized so that older persons and persons with disabilities can participate actively and
where required, assistive products and support staff are used to facilitate participation
3.2
assistive product
any product (including devices, equipment, instruments and software), especially produced or generally
available, used by or for persons with disability
- for participation;
- to protect, support, train, measure or substitute for body functions/structures and activities; or
- to prevent impairments, activity limitations or participation restrictions
3.3
support staff
person who performs tasks to facilitate the execution of an accessible meeting which can include, but not
limited to, interpreting, note taking, guiding, and assisting participation of older persons and persons with
disabilities. Support staff includes guide assistant (3.4) and communication assistant (3.5).
© ISO 2002 – All rights reserved 1
---------------------- Page: 6 ----------------------
ISO/DIS 17069
3.4
guide assistant
person who leads and assists a person in a location in an appropriate manner for that person’s impairment
3.5
communication assistant
person who assists with communication
Examples
-a person who conveys proceedings of meeting and discussions using sign languages, live captioning, or by
paraphrasing
- a person who expresses opinions on behalf of a participant
- a person who assists participant to follow documentation e.g. turns pages of documents, points out
information in documents
3.6
attendant
person who accompanies an older person or a person with disabilities and enables them to participate in the
meeting
3.7
information services
interactive communication support using support staff and assistive products so that older persons and
persons with disabilities can actively participate
4. Planning and management for full participation
4.1 Principle
4.1.1 Basic principle
Meeting organizers should be aware of factors that can hinder the participation of older persons and
persons with disabilities in meetings.
When planning a meeting, the organizer should identify and consider measures they should take to
facilitate full participation of the persons who intend to participate in the meeting.
4.1.2 Before the meeting
All participants should receive necessary information in an appropriate format and be requested to
express any requirements they may have in relation to active participation. For this purpose, prior
registration may be helpful. (See Annex B)
The meeting venue and program should accommodate the requirements of the participants.
The meeting organizers should inform staff concerning requirements of participants.
The meeting organizers and support staff should plan how they will provide the support required and
emergency procedures in relation to participants’ requirements. Communication method in emergency
situations and evacuation procedures should be established and clarified.
The meeting organizers should brief speakers, workshop leaders, moderators, etc. concerning
considerations to be taken when presenting and leading the meeting in relation to the participants’
requirements.
© ISO 2002 – All rights reserved
---------------------- Page: 7 ----------------------
ISO/DIS 17069
The meeting organizers should inform all meeting participants of any allergens or sensitizing substances
that they should not wear, use or bring to the meeting in relation to participants’ requirements.
4.1.3 At the meeting
Information presented at the meeting should accommodate the requirements of the participants.
All participants should be informed of considerations they should take to ensure that all present can
participate actively. Such considerations include, but are not limited to, information on special seating
arrangements, use of microphone, speaking slowly to allow for interpretation, introducing themselves
before speaking, allergy considerations, dietary considerations, and location of restrooms.
4.1.4 After the meeting
Meeting records should be produced in formats to accommodate requirements of the participants.
Participants should be given the opportunity to give feedback concerning accessibility of the meeting.
Meeting organizers should review feedback and make adjustments in planning procedures/checklists for
subsequent meetings.
4.2 Specific Considerations and supports
4.2.1 General
This clause includes considerations and supports in relation to specific human functions. Further
information on accessibility, design considerations and human functions/abilities/disabilities can be found
in ISO/IEC Guide 71.
Examples of related support include assistive products and personnel that are provided by the meeting
organizer and those brought to the meeting by the person with disability. For those that are brought to the
meeting by the participant, the organiser should ensure that the assistive product or personnel can be
accommodated at the meeting.
4.2.2 Seeing
4.2.2.1 Considerations
Considerations should be taken regarding written information, mobility and orientation in relation to
blindness and low vision as well as appropriate colour scheme in relation to colour identification disability.
4.2.2.2 Examples of related support
- Appropriate colour scheme in documents and signage (colour identification disability)
- Audio or enlarged letters version of documents (low vision)
- Braille, audio or digital version of documents (blind)
- Devices such as braille displays, braille typewriters, slates, computers with reading application (blind)
- Devices such as image-enlarging video systems, large screen monitors (low vision)
- Tactile walking surface indicator, tactile guide maps, etc. (low vision, blind)
- Support staff such as guide assistants
- Relevant information and work space to accommodate attendants
© ISO 2002 – All rights reserved 3
---------------------- Page: 8 ----------------------
ISO/DIS 17069
4.2.3 Hearing
4.2.3.1 Considerations
Consideration should be taken in relation to spoken communication, presentations, discussions and audio
alarm notifications.
4.2.3.2 Examples of related support
- Devices such as amplifiers, loudspeakers, projectors, white boards, microphones (hard of hearing)
- Sign language interpretation and speech to text/CART/captioning and note-taking (deaf, hard of hearing)
- Assistive systems for hearing (hard of hearing)
- Interpreting system as per preference/requirement of participant (deafblind)
- Information services and communication assistants
- Relevant information and work space to accommodate attendants
Note 1 Assistive systems for hearing include radio frequency transmission systems, Infrared systems for audio
information, and induction-loop system.
Note 2 CART (Communication Access Real time Translation) is real time display of verbatim report on a
computer/large screen, using a special keyboard/stenotype via special software. CART is sometimes referred
to as ―speech to text‖.
Captioning is to provide a piece of text appearing on screen as part of a film or broadcast.
Note-taking is to produce a summary report by hand-written paper (manual note-taking) or on screen of laptop
computer (computerized note-taking).
Subtitle is captions displayed at the bottom of a cinema or television screen that translate or transcribe the
dialogue or narrative.
4.2.4 Touch
4.2.4.1 Considerations
Meeting venues should be inspected in relation to anything that may require intact sensory ability such as
sharp edges and hot or cold surfaces. If there are any questions concerning safety, the participants with
sensory impairment should be contacted prior to meeting.
4.2.5 Taste or smell
4.2.5.1 Considerations
Consideration should be taken in relation to anything that requires intact taste and/or smell ability. If there are
any questions concerning safety, the participants with taste or smell impairment should be contacted prior to
meeting.
© ISO 2002 – All rights reserved
---------------------- Page: 9 ----------------------
ISO/DIS 17069
4.2.6 Hand and arm use
4.2.6.1 Considerations
Meeting venues and routes to local parking and transportation facilities should be inspected in relation to
anything that can be a hinder in relation to hand and arm use such as doors that are manually opened,
placement of objects and materials that are to be handled, etc.
4.2.6.2 Examples of Related support
- Alternate routes with appropriate signage
- Arrangement of meeting room and placement of documents, materials, refreshments, etc.
- Paper clips to facilitate handling of documents
- Support staff, guide assistant
- Relevant information and work space to accommodate attendants
NOTE Hand and arm use corresponds to upper body functions in ISO/IEC Guide 71.
4.2.7 Mobility
4.2.7.1 Considerations
Meeting venues and routes to local parking and transportation facilities should be inspected in relation to
anything that can be a hinder in relation to mobility such as uneven pavement, steps, lack of adequate space
for walking aids and wheelch
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.